Zotac H67ITX User Manual

1

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with instructions
contained in this manual, may cause harmful interference to radio and television communications.
However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

- REORIENT OR RELOCATE THE RECEIVING ANTENNA

- INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER

- CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM
THAT OF THE RECEIVER

- CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION TECHNICIAN

NOTE:

Connecting this device to peripheral devices that do not comply with Class B requirements, or
using an unshielded peripheral data cable, could also result in harmful interference to radio or
television reception.

The user is cautioned that any changes or modications not expressly approved by the party

responsible for compliance could void the user’s authority to operate this equipment.

To ensure that the use of this product does not contribute to interference, it is necessary to use
shielded I/O cables.

Copyright

This manual is copyrighted with all rights reserved. No portion of this manual may be copied or
reproduced by any means.

While every precaution has been taken in the preparation of this manual, no responsibility for
errors or omissions is assumed. Neither is any liability assumed for damages resulting from the
use of the information contained herein.

Trademarks

All brand names, logos and registered trademarks mentioned are property of their respective
owners.

CAUTION:

Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled

where possible. Disposal of used batteries must be in accordance with local environmental
regulations.

Electronic Emission Notices

WARNING!

2

Intel H67-ITX series Motherboard

Table of Contents

Motherboard Specications ---------------------------------------------------------------------------------4
Motherboard Layout--------------------------------------------------------------------------------------------6
Hardware Installation ------------------------------------------------------------------------------------------9

Safety Instructions-------------------------------------------------------------------------------------------9
Preparing the Motherboard -------------------------------------------------------------------------------10

Installing the CPU -------------------------------------------------------------------------------------- 10
Installing the CPU Fan -------------------------------------------------------------------------------- 11
Installing Memory Modules --------------------------------------------------------------------------11

Installing the Motherboard --------------------------------------------------------------------------------12

Installing the I/O Shield -------------------------------------------------------------------------------12
Securing the Motherboard into the Chassis -----------------------------------------------------12

Connecting Cables and Setting Switches -------------------------------------------------------------13

24-pin ATX Power Connector-PW1 ----------------------------------------------------------------14
4-pin ATX_12V power connector-PW2 -----------------------------------------------------------14
SPDIF-Out Header-CN5------------------------------------------------------------------------------15
COM Header-CN4 (Optional) -----------------------------------------------------------------------15
Front panel header-FP1 ------------------------------------------------------------------------------15
USB Headers-FP_U1/2/FP_USB3_1 -------------------------------------------------------------16
Front Pannel Audio Header-FP_S1 ---------------------------------------------------------------16
Speaker Header-SPK1 -------------------------------------------------------------------------------17
Serial-ATA (SATA) Connectors (SATA1~6) ------------------------------------------------------17
Fan Connectors-----------------------------------------------------------------------------------------17
Expansion Slots ----------------------------------------------------------------------------------------18
Jumper Settings ----------------------------------------------------------------------------------------18

Conguring the BIOS ------------------------------------------------------------------------------------------19

Enter BIOS Setup -------------------------------------------------------------------------------------------19
Main Menu ----------------------------------------------------------------------------------------------------19
Advanced Menu----------------------------------------------------------------------------------------------20

X-Setting --------------------------------------------------------------------------------------------------20
Storage Conguration --------------------------------------------------------------------------------- 20
H/W Monitor ---------------------------------------------------------------------------------------------20

CPU Conguration ------------------------------------------------------------------------------------- 21
USB Conguration -------------------------------------------------------------------------------------21
Super IO Conguration -------------------------------------------------------------------------------21

ACPI Settings -------------------------------------------------------------------------------------------22

Chipset Menu ------------------------------------------------------------------------------------------------- 22

Display Conguration ---------------------------------------------------------------------------------22
OnBoard Device Cong ------------------------------------------------------------------------------22

Boot Menu ----------------------------------------------------------------------------------------------------- 23

3

Table of Contents

Boot Settings Conguration -------------------------------------------------------------------------23

Security Menu ------------------------------------------------------------------------------------------------24

Administrator Password ------------------------------------------------------------------------------24
User Password ------------------------------------------------------------------------------------------24

Exit Menu ------------------------------------------------------------------------------------------------------ 25

Save Changes and Exit-------------------------------------------------------------------------------25
Discard Changes and Exit ---------------------------------------------------------------------------25

Save Changes and Reset ---------------------------------------------------------------------------- 25
Discard Changes and Reset ------------------------------------------------------------------------25
Save Changes ------------------------------------------------------------------------------------------25
Discard Changes --------------------------------------------------------------------------------------- 26
Restore Defaults----------------------------------------------------------------------------------------26
Save as User Defaults --------------------------------------------------------------------------------26
Restore User Defaults --------------------------------------------------------------------------------26
Launch EFI Shell from lesystem device --------------------------------------------------------26

Flash Update Procedure ---------------------------------------------------------------------------------- 26

Installing Drivers and Software ----------------------------------------------------------------------------27

Drivers Installation ------------------------------------------------------------------------------------------27
Realtek HD Audio Driver Setup -------------------------------------------------------------------------39
Getting Started ------------------------------------------------------------------------------------------39
Sound Effect ---------------------------------------------------------------------------------------------39
Mixer ------------------------------------------------------------------------------------------------------- 41
Audio I/O -------------------------------------------------------------------------------------------------- 43
Microphone -----------------------------------------------------------------------------------------------47
3D Audio Demo -----------------------------------------------------------------------------------------48
Information ----------------------------------------------------------------------------------------------- 48

SATA RAID User Manual --------------------------------------------------------------------------------------49

Setting up the BIOS ----------------------------------------------------------------------------------------- 49
Entering the RAID BIOS utility ---------------------------------------------------------------------------50
Creating a RAID set ----------------------------------------------------------------------------------------- 50
Deleting a RAID set -----------------------------------------------------------------------------------------51

4

Intel H67-ITX series Motherboard

Motherboard Specications

q Chipset

v Intel® H67 Chipset

q Size

v Mini ITX form factor of 6.7 X 6.7 inch

q Microprocessor support

v Supports LGA 1155 Socket for 2nd Generation Intel® Core i3/i5/i7 and Pentium processors

q Operating systems

v Supports Windows XP 32bit/64bit, Windows Vista 32bit/64bit and Windows 7 32bit/64bit

q System Memory

v Supports 1 GB, 2 GB, 4 GB and 8 GB DDR3 DRAM devices

v Supports Dual Channel DDR3 1066 and 1333 MT/s

v Maximum memory size: 16 GB

q USB 2.0 ports

v Supports hot plug and play

v Eight USB 2.0 ports (four ports on the back panel, four via the USB brackets connected

to the internal USB headers)

v Supports USB 2.0 protocol up to 480 Mbps transmission rate

q USB 3.0 ports

v Supports hot plug and play

v Four USB 3.0 ports (two on the back panel, two via the USB bracket connected to the

internal USB header)

v Fully backward compatible with USB 2.0 and 1.1 specications

q Onboard Serial ATA ports

v Independent DMA operation on six ports

v Two SATAIII ports(6.0 Gb/s) and four SATAII ports(3.0 Gb/s)

q eSATA Port

v One eSATA port on backpanel

v Supports hot plug and play

v Provide a link for 3.0 Gb/s data speed

q Onboard LAN

v Support Full Duplex ow control (IEEE802.3x)

v 10/100/1000 BASE-T IEEE 802.3 compliant

5

Motherboard Specications

v Wake On LAN (WOL) power management support

q WiFi support

v Compliant with IEEE802.11n Draft 2.0 Standard

v High speed wireless connection and enhanced wireless security

v Max transfer rate up to 300 Mbps or 150 Mbps (optional for different models)

q Audio

v 8 channel High Denition Audio (including one optical SPDIF output port)

v All DACs support 192k/96k/48k/44.1kHz sample rate

v One SPDIF-out header on board

q Green Function

v Support SMM, APM, ACPI

v Suspend to DRAM supported (STR)

v AC power failure recovery

q Onboard Graphics Features

v Integrated GPU contains a refresh of the sixth generation graphics core

v DX10.1 and OpenGL 3.0 are supported

v 3D Graphics Rendering Enhancements

v HDMI/DP/DVI ports output support (DVI-VGA adaptor bundled in some model)

v Support resolution up to 1920x1200 @ 60Hz for HDMI/DVI and 2560x1600 @ 60Hz for DP

q PCI Express Interface

v Supports PCI Express 2.0

v Wake up function is supported

v Clock spread spectrum capability

q Expansion slots

v One PCI Express x16 slot

v One Mini PCI Express slot (full-height)

6

Intel H67-ITX series Motherboard

120

240

121

120

240

121

1.5V

1.5V

115XLM

LGA1156

REMOVE

LOTES

+

1

5

CPUFAN

PCIE_X16

7

SATA2
SATA1

SATA4

8

9

10

PW2

11

14

15

Chipset

16

17

19 20

DDRIII1

DDRIII2

MINI_PCIE1

2

51

52

K/B USB3.0

DVI

USB/e_SATA

LAN/USB

SD1

CN4

PW1

FP1

SPK1

CN5

FP_S1

DP/HDMI

SW1

FP_U1

FP_U2

SATA3

SATA6
SATA5

2

3

4

13

1

12

FP_USB3_1

18

6

JP1

1

SYSFAN1

Motherboard Layout

Figure 1 shows the motherboard and Figure 2 shows the back panel connectors.

Figure 1. Board Layout

1. COM Header-CN4 (Optional)

2. 24-pin ATX Power Connector-PW1

3. CPU Fan Connector-CPUFAN1

4. Front Panel Header-FP1

5. Speaker Header-SPK1

6. PCI Express x16 Slot-PCIE_X16

7. CPU Socket

8. 4-pin ATX_12V power connector-PW2

9. SPDIF-Out Header-CN5

10. Front Pannel Audio Header-FP_S1

11. Backpanel Connectors

12. Clear CMOS Button-SW1

13. USB 3.0 Header-FP_USB3_1

14. USB 2.0 Headers (FP_U1~FP_U2)

15. Serial-ATA (SATA) Connectors (SATA1~6)

16.

Chipset

17. SYS Fan Connector-SYSFAN1

18. Clear CMOS Jumper-JP1

19. Mini PCI Express Slot-MINI_PCIE1

20. DDRIII DIMM Sockets-DDRIII1~2

Figure 1

7

Rear panel

1. USB 3.0 Ports

3. DVI Port

2. HDMI Port

4. eSATA Port

1

2

3

8

4

6

9

7

5

10

Figure 2. Backpanel connectors

9. DisplayPort

10. PS2 Keyboard/Mouse Port
(Refer to page 21 to set PS2 Keyboard/Mouse Swap)

11

5. USB 2.0 Ports 6. Optical SPDIF Output

Activity LED

Status Descritption

Off No link

Orange Linked

Blinking Data activity

8. LAN port LED indicators
Speed LED

Status Description

Off Speed: 10 Mbps

Green Speed: 100 Mbps

Orange Speed: 1000 Mbps

Speed LED Activity LED

7. Port 2-Channel 4-Channel 6-Channel 8-Channel

Blue Line-In Line-In Line-In Side Speaker Out

Green Line-Out Front Speaker Out Front Speaker Out Front Speaker Out

Pink Mic In Mic In Mic In Mic In

Black -- -- Center/Subwoofer Center/Subwoofer

Orange -- Rear Speaker Out Rear Speaker Out Rear Speaker Out

8

Intel H67-ITX series Motherboard

11. WiFi antenna connectors (Optional)

This motherboard can support two WiFi antenna modules. Refer to the following to install

the WiFi antenna modules.

Step 1. Remove the red caps from the WiFi antenna connectors.

Step 2. Install the WiFi antennas to the WiFi antenna connectors, and make sure the screws

are rotated in clockwise direction.







Note: 1. Users please note that the appearance of your WiFi antenna modules may

not be exactly the same as those shown in this manual.

2. Users can install one or two WiFi antennas to the motherboard.

3. Users can bend or rotate the WiFi antennas to the best receiving direction

according to the picture below.

120

240

121

120

240

121

1.5V

1.5V

115XLM

LGA1156

REMOVE

LOTES

+







9

Hardware Installation

This section will guide you through the installation of the motherboard. The topics covered in this

section are:

q Preparing the motherboard

v Installing the CPU

v Installing the CPU fan

v Installing Memory DIMMs

q Installing the motherboard

q Connecting cables and setting switches

Safety Instructions

To reduce the risk of re, electric shock, and injury, always follow basic safety precautions.

Remember to remove power from your computer by disconnecting the AC main source before

removing or installing any equipment from/to the computer chassis.

Hardware Installation

10

Intel H67-ITX series Motherboard

Preparing the Motherboard

The motherboard shipped in the box does not contain a CPU or memory DIMM. You need to

purchase them to complete this installation.

Installing the CPU

Be very careful when handling the CPU. Make sure not to bend or break any pins on the back.

Hold the processor only by the edges and do not touch the bottom of the processor.

The following illustration shows CPU installtaion components

1. Unhook the socket lever by pushing down

and away from the socket.

2. Lift the socket lever and the load plate to

fully open position.

3. Use your thumb and forenger to lift the cap

up vertically.

● Be careful not to touch the socket contacts.

4. Hold the processor with your thumb and

forenger. Insert the processor into the socket

vertically.

● Align the CPU pin 1 mark with the pin 1

corner of the CPU socket.

5. Make sure the CPU is fully seated, and then

replace the load plate.

● Be sure that the front end of the load

plate is under the shoulder screw.

6. Secure the load lever to its locked location.

11

Installing the CPU Fan

There are many different fan types that can be used with this motherboard. Follow the instruction

that came with your fan assembly. Be sure that the fan orientation is correct for your chassis type

and your fan assembly.

Installing Memory Modules

Your new motherboard has two 1.5V 240-pin slots for DDR3 memory. These slots support 1

GB/2 GB/4 GB/8 GB DDR3 devices. There must be at least one memory bank populated to

ensure normal operation. Refer to the following recommendations to install memory modules.

Note that a memory module has a notch, so it can only t in one direction. Refer to the following

procedure to install memory modules into the slots on the motherboard.

1. Unlock a DIMM slot by pressing the module clips outward.

2. Align the memory module to the DIMM slot, and insert the module vertically into the DIMM

slot. The plastic clips at both sides of the DIMM slot automatically lock the DIMM into the
connector.

120

240

121

120

240

121

1.5V

1.5V

115XLM

LGA1156

REMOVE

LOTES

+

DDRIII1

DDRIII2

Hardware Installation

12

Intel H67-ITX series Motherboard

Installing the Motherboard

The sequence of installing the motherboard into the chassis depends on the chassis you are

using and if you are replacing an existing motherboard or working with an empty chassis. Deter-

mine if it would be easier to make all the connections prior to this step or to secure the mother-

board and then make all the connections. It is normally easier to secure the motherboard rst.

Use the following procedure to install the I/O shield and secure the motherboard into the chassis.

Note: Be sure that the CPU fan assembly has enough clearance for the chassis covers

to lock into place and for the expansion cards. Also make sure the CPU Fan assem

-bly is aligned with the vents on the covers.

Installing the I/O Shield

The motherboard kit comes with an I/O shield that is used to block radio frequency transmis-

sions, protects internal components from dust and foreign objects, and promotes correct airow

within the chassis.

Before installing the motherboard, install the I/O shield from the inside of the chassis. Press the

I/O shield into place and make sure it ts securely. If the I/O shield does not t into the chassis,

you would need to obtain the proper size from the chassis supplier.

Securing the Motherboard into the Chassis

Most computer chassis have a base with mounting studs or spacers to allow the motherboard

to be secured to the chassis and help to prevent short circuits. If there are studs that do not

align with a mounting hole on the motherboard, it is recommended that you remove that stud

to prevent the possibility of a short circuit. In most cases, it is recommended to secure the

motherboard with spacers.

1. Carefully place the motherboard onto the studs/spacers located inside the chassis.

2. Align the mounting holes with the studs/spacers.

3. Align the connectors to the I/O shield.

4. Ensure that the fan assembly is aligned with the chassis vents according to the fan assembly

instruction.

5. Secure the motherboard with screws.

13

Hardware Installation

Connecting Cables and Setting Switches

This section takes you through all the connectors and switch settings necessary on the mother-

board. This will include:
q Power Connectors
v 24-pin ATX Power Connector-PW1

v 4-pin ATX_12V Power Connector-PW2
q Internal Headers/Connectors
v SPDIF-Out Header-CN5
v COM Header-CN4 (Optional)
v Front Panel Header-FP1
v USB Headers (FP_U1/2/FP_USB3-1)
v Front Pannel Audio Header-FP_S1
v Speaker Header-SPK1
q Serial-ATA (SATA) Connectors (SATA1~6)
q Fan Connectors
q Expansion Slots
q CMOS Jumper Settings

See Figure 1 to locate the connectors and jumpers referenced in the following procedure.

14

Intel H67-ITX series Motherboard

24-pin ATX Power Connector-PW1

PW1 is the main power supply connector. Make sure that the power supply cable and pins are

properly aligned with the connector on the motherboard. Firmly plug the power supply cable into

the connector and make sure it is secure.

PW1-Pin Denition

Pin Signal Pin Signal

1 +3.3V 13 +3.3V

2 +3.3V 14 -12V

3 GND 15 GND

4 +5V 16 PS_ON

5 GND 17 GND

6 +5V 18 GND

7 GND 19 GND

8 PWROK 20 -5V

9 +5V_AUX 21 +5V

10 +12V 22 +5V

11 +12V 23 +5V

12 +3.3V 24 GND

4-pin ATX_12V power connector-PW2

PW2, the 4-pin ATX 12V power connector, is used to provide power to the CPU. Align the pins to

the connector and press rmly until seated.

PW2-Pin Denition

Pin Signal

1 GND

2 GND

3 +12V

4 +12V

120

240

121

120

240

121

1.5V

1.5V

115XLM

LGA1156

REMOVE

LOTES

+

1

PW2

PW1

1

12

13

24

15

Hardware Installation

SPDIF-Out Header-CN5

This header provides a SPDIF (Sony/Philips Digital Interface) output to digital multimedia

device through coaxial connector.

CN5 - Pin Denition

Pin Signal

1 GND

2 SPDIF-out

3 VCC

q PWRLED

Attach the front panel power LED cable to these two pins of the connector. The Power LED

indicates the system’s status.

q PWR SW

Attach the power button cable from the case to these two pins. Pressing the power button

on the front panel turns the system on and off rather than using the power supply button.

q HDD LED

Attach the hard disk drive indicator LED cable to these two pins. The HDD indicator LED

indicates the activity status of the hard disks.

q RST SW

Attach the Reset switch cable from the front panel of the case to these two pins. The system

restarts when the RESET switch is pressed.

Note: Some chassis do not have all four cables. Be sure to match the name on the

connectors to the corresponding pins.

Front panel header-FP1

The front panel header on this motherboard is

one connector used to connect the following four

cables :

CN5

1

120

240

121

120

240

121

1.5V

1.5V

115XLM

LGA1156

REMOVE

LOTES

+

FP1

CN4

1

COM Header-CN4 (Optional)

CN4 - Pin Denition

Pin Signal Pin Signal

1 DCD 2 RXD

3 TXD 4 DTR

5 GND 6 DSR

7 RTS 8 CTS

9 RI 10 NC

FP1-Pin Denition

Pin Signal Pin Signal

1 HDD_LED+ 2 PW_LED+

3 HDD_LED- 4 PW_LED-

5 GND 6 PWR_SW

7 RESET 8 GND

9 NC 10 KEY

16

Intel H67-ITX series Motherboard

USB Headers-FP_U1/2/FP_USB3_1

This motherboard contains four USB 2.0 and two USB 3.0 ports that are exposed on the rear

panel of the chassis. The motherboard also contains two 10-pin internal USB 2.0 headers and

one 20-pin USB 3.0 connector onboard.

Front Panel Audio Header-FP_S1

The audio connector supports HD audio standard

and provides two kinds of audio output choices: the

Front Audio, the Rear Audio. The front Audio supports

retasking function.

Note:

In order to utilize the front audio

header, your chassis must have front

audio connector. Also please make

sure the pin assignment on the cable

is the same as the pin assignment

on the mainboard header. To nd

out if the chassis you are buying

supports a front audio connector,

please contact your dealer.

FP_U1~FP_U2-Pin Denition

PIN Assignment PIN Assignment

1 VCC 2 VCC

3 USBP0- 4 USBP1-

5 USBP0+ 6 USBP1+

7 GND 8 GND

9 KEY 10 NC

FP_S1-Pin Denition

PIN Assignment PIN Assignment

1 MIC2(L) 2 GND

3 MIC(R) 4 -ACZ-DET

5 Front Audio(R) 6 Reserved

7 FAVDIO-JD 8 Key(No pin)

9 Front Audio(L) 10 Reserved

120

240

121

120

240

121

1.5V

1.5V

115XLM

LGA1156

REMOVE

LOTES

+

1

FP_S1

1

FP_U11FP_U2

FP_USB3_1

1

FP_USB3_1-Pin Denition

Pin Signal Pin Signal

1 NC 2 BD+

3 AD+ 4 BD-

5 AD- 6 GND2

7 GND1 8 BSSTX+

9 ASSTX+ 10 BSSTX-

11 ASSTX- 12 GND3

13 GND 14 BSSRX+

15 ASSRX+ 16 BSSRX-

17 ASSRX- 18 BVBUS

19 AVBUS 20 KEY

Note: Secure the bracket to

either the front or rear panel

of your chassis (not all chas-

sis are equipped with the front

panel option).