Zotac 740G, 760G, 780G User Manual
1
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with instructions
contained in this manual, may cause harmful interference to radio and television communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- REORIENT OR RELOCATE THE RECEIVING ANTENNA
- INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER
- CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM
THAT OF THE RECEIVER
- CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION TECHNICIAN
NOTE:
Connecting this device to peripheral devices that do not comply with Class B requirements, or
using an unshielded peripheral data cable, could also result in harmful interference to radio or
television reception.
The user is cautioned that any changes or modications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
To ensure that the use of this product does not contribute to interference, it is necessary to use
shielded I/O cables.
Copyright
This manual is copyrighted with all rights reserved. No portion of this manual may be copied or
reproduced by any means.
While every precaution has been taken in the preparation of this manual, no responsibility for
errors or omissions is assumed. Neither is any liability assumed for damages resulting from the
use of the information contained herein.
Trademarks
All brand names, logos and registered trademarks mentioned are property of their respective
owners.
Electronic Emission Notices
WARNING!
2
AMD 740G/760G/780G motherboard
Table of Contents
Motherboard Specications ------------------------------------------------------------------- 4
Motherboard Layout------------------------------------------------------------------------------ 6
Hardware Installation ---------------------------------------------------------------------------- 8
Safety Instructions ----------------------------------------------------------------------------- 8
Preparing the motherboard ------------------------------------------------------------------ 8
Installing the CPU ------------------------------------------------------------------------- 9
Installing the CPU Fan ------------------------------------------------------------------- 9
Installing Memory Modules ------------------------------------------------------------- 10
Installing the motherboard ------------------------------------------------------------------- 11
Installing the I/O Shield ------------------------------------------------------------------ 11
Securing the Motherboard into the Chassis ---------------------------------------- 11
Connecting Cables and Setting Switches ------------------------------------------------ 12
24-pin ATX Power Connector ---------------------------------------------------------- 13
4-pin ATX 12V Power Connector ------------------------------------------------------ 13
USB Headers ------------------------------------------------------------------------------- 14
FP Audio Header -------------------------------------------------------------------------- 14
Front Panel Header ----------------------------------------------------------------------- 15
Speaker Header --------------------------------------------------------------------------- 15
Hard Disk Connector --------------------------------------------------------------------- 16
SPDIF-Out Connector -------------------------------------------------------------------- 16
COM Header ------------------------------------------------------------------------------- 16
Connecting Serial ATA Cables (optional) -------------------------------------------- 17
Fan Connectors ---------------------------------------------------------------------------- 17
Expansion Slots ---------------------------------------------------------------------------- 18
Jumper Settings --------------------------------------------------------------------------- 19
Conguring the BIOS ---------------------------------------------------------------------------- 20
Enter BIOS Setup ------------------------------------------------------------------------------ 20
Main Menu --------------------------------------------------------------------------------------- 20
X-Setting Menu --------------------------------------------------------------------------------- 21
Advanced Menu -------------------------------------------------------------------------------- 21
CPU Conguration ------------------------------------------------------------------------ 21
SATA Conguration ----------------------------------------------------------------------- 22
Power Conguration ---------------------------------------------------------------------- 22
USB Conguration ------------------------------------------------------------------------ 22
Security -------------------------------------------------------------------------------------- 23
PCIPnP -------------------------------------------------------------------------------------- 23
Chipset Menu ----------------------------------------------------------------------------------- 24
Display Conguration--------------------------------------------------------------------- 24
OnBoard Device Conguration -------------------------------------------------------- 24
Memory Conguration -------------------------------------------------------------------- 24
PCI Express Conguration -------------------------------------------------------------- 24
PC Health Menu -------------------------------------------------------------------------------- 25
3
CPUFAN Mode Setting ------------------------------------------------------------------ 25
Boot Menu --------------------------------------------------------------------------------------- 25
Boot Settings Conguration------------------------------------------------------------- 25
Exit Menu ---------------------------------------------------------------------------------------- 26
Save Changes and Exit ------------------------------------------------------------------ 26
Discard Changes and Exit -------------------------------------------------------------- 26
Discard Changes -------------------------------------------------------------------------- 26
Load Optimal Defaults ------------------------------------------------------------------- 26
Load Failsafe Defaults ------------------------------------------------------------------- 27
Flash Update Procedure -------------------------------------------------------------------- 27
Installing Drivers and Software -------------------------------------------------------------- 28
Drivers Installation ---------------------------------------------------------------------------- 28
Realtek HD Audio Driver Setup ----------------------------------------------------------- 32
Getting Started ----------------------------------------------------------------------------- 32
Sound Effect -------------------------------------------------------------------------------- 32
Mixer------------------------------------------------------------------------------------------ 34
Audio I/O------------------------------------------------------------------------------------- 36
Microphone --------------------------------------------------------------------------------- 40
3D Audio Demo ---------------------------------------------------------------------------- 41
Information --------------------------------------------------------------------------------- 41
SATA RAID User Manual ------------------------------------------------------------------------ 42
Setting up the BIOS --------------------------------------------------------------------------- 42
Entering the RAID BIOS Setup ------------------------------------------------------------- 44
Creating a RAID set --------------------------------------------------------------------------- 44
Deleting a RAID set --------------------------------------------------------------------------- 45
Installing the RAID Drivers ------------------------------------------------------------------- 46
Table of Contents
4
AMD 740G/760G/780G motherboard
Motherboard Specications
q Chipset
v AMD® 740G/760G/780G + SB710
q Size
v Micro ATX form factor of 7.2 inch X 8.7 inch
q Microprocessor support
v AMD® PhenomTM II/AthlonTM II/SempronTM with socket AM3 (TDP max:65W)
q Operating systems:
v Supports Windows XP 32 bit/64 bit, Windows Vista 32 bit/64 bit and Windows 7
32bit/64bit
q System Memory support
v Supports Dual Channel DDR3 1333/1066/800, maximum memory size: 8 GB
q USB 2.0 Ports
v Supports hot plug and play
v Twelve USB 2.0 ports (four on the back panel, eight via the USB brackets
connected to the internal USB headers) (optional)
v Supports USB 2.0 protocol up to 480 Mbps transmission rate
q Onboard Serial ATA II
v Independent DMA operation on four ports (optional)
v Data transfer rates of 300 Mb/s
q Onboard LAN
v Supports IEEE 802.3
v Supports 10/100 Mbps Ethernet
q Onboard Audio
v Azalia High-Denition audio
v Supports 6-channel audio
v Supports Jack-Sensing function
q PCI Express Support
v Supports PCI Express 1.0
v Low power consumption and power management features
q Green Function
v Supports ACPI (Advanced Conguration and Power Interface)
v Suspend to DRAM supported (STR)
5
v RTC timer to power-on the system
v AC power failure recovery
q Onboard Graphics Support
v Integrates ATI Radeon 2100 Graphics (740G)/ATI Radeon 3000 Graphics
(760G)/ATI Radeon HD 3200 Graphics (780G)
v Supports DirectX 9.0 (740G), DirectX10 (760G/780G)
v VGA and DVI port output support
q Expansion Slots
v One PCI Express x16 slot
v One PCI Express x1 slot
v One PCI slot
Motherboard Specications
6
AMD 740G/760G/780G motherboard
Motherboard Layout
Figure 1. Board Layout
120
240
121
120
240
121
1.5V
1.5V
.
.
.
1
7
CPU FAN
SATA 4
11
12
13
PCI 1
19
21
DDR II I1
DDR II I2
KB/ MS
DVI
LA N/U SB
AUD IO
FP_ S1
J1
SYS FAN
FP2
PCI EX 1
3
5
FP_ U2
8
JP1
6
9
10
COM 1
Sou th bri dg e
Nor th br idg e
5
PWR 1
2
SATA 3SATA 2
SATA 1
FP1
FP_ U4
FP_ U1
FP_ U3
14
CN4
15
PCI EX 2
16
17
4
18
20
USB
VGA
IDE
1. CPU fan connector
2. 4-pin ATX_12V power connector
3. 24-pin ATX power connector
4. IDE connector
5. SATA connectors
6. SYS fan connector
7. Front pannel header
8. Southbridge
9. Speaker header
10. Clear CMOS jumper
11. USB headers
12. PCI slot
13. COM header
14. SPIDF connector
15. PCI Express x1 slot
16. Front pannel audio header
17. PCI Express x16 slot
18. Backpanel connectors
19. Northbridge
20. CPU socket
21. DDR3 slots
7
Figure 2: Backpanel connectors
Rear Panel
6
11
5
10
15
2
4
7
5
1
3
6
Activity LED
Status Descritption
Off No link
Orange Linked
Blinking Data activity
7. LAN port LED indicators
Speed LED
Status Description
Off Speed: 10 Mbps
Green Speed: 100 Mbps
Speed LED Activity LED
1. PS/2 Mouse Port
2. PS/2 Keyboard Port
3. VGA Connector
4. DVI Port
5. USB Ports
6. Port 2-Channel 4-Channel 6-Channel
Blue Line-In Rear Speaker Out Rear Speaker Out
Green Line-Out Front Speaker Out Front Speaker Out
Pink Mic In Mic In Center/Subwoofer
8
AMD 740G/760G/780G motherboard
Hardware Installation
This section will guide you through the installation of the motherboard. The topics
covered in this section are:
q Preparing the motherboard
v Installing the CPU
v Installing the CPU fan
v Installing Memory Modules
q Installing the motherboard
v Installing the I/O shield
v Securing the Motherboard into the Chassis
q Connecting cables and setting switches
Safety Instructions
To reduce the risk of re, electric shock, and injury, always follow basic safety precations.
Remember to remove power from your computer by disconnecting the AC main
source before removing or installing any equipment from/to the computer chassis.
Preparing the Motherboard
The motherboard shipped in the box does not contain a CPU and memory. You need
to purchase these to complete this installation.
9
Installing the CPU
Be very careful when handling the CPU. Make sure not to bend or break any pins on
the back. Hold the processor only by the edges and do not touch the bottom of the
processor.
Use the following procedure to install the CPU onto the motherboard.
1. Please turn off the power and unplug the power
cord before installing the CPU. Pull the lever up and
away from the socket until it is at a 90 degree angle
to the motherboard.
2. Look for the gold arrow on the CPU. The gold arrow
should point away from the lever pivot. The CPU can
only sit properly in the socket in the correct orientation.
3. If the CPU is correctly seated, the pins should be
completely embedded in the socket and can not be
seen (Please note that any deviation from the correct
installation procedures may cause permanent damage
to your motherboard).
4. Press the CPU down rmly into the socket and
close the lever. As the CPU is likely to move while
the lever is being closed, always close the lever with
your ngers pressing tightly on top of the CPU to
make sure the CPU is properly and completely seated
in the socket.
5. When you are installing the CPU, make sure the
CPU has a heat sink and a cooling fan attached on
the top to prevent overheating. If you do not have the
heat sink and cooling fan, contact your dealer to
purchase and install them before turning on the
computer.
Installing the CPU Fan
There are many different fan types that can be used with this motherboard. Follow the
instruction that came with your fan assembly. Be sure that the fan orientation is correct
for your chassis type and your fan assembly.
Hardware Installation
10
AMD 740G/760G/780G motherboard
120
240
121
120
240
121
1.5V
1.5V
.
.
.
DDRIII2
DDRIII1
Installing Memory Modules
This motherboard accommodates two memory modules. It can support two 240-pin
DDR3 1333/1066/800. The total memory capacity is 8 GB. You must install at least
one module in any of the two slots. Refer to the following recommendations to install
the memory modules.
Note that a memory module has a notch, so it can only t in one direction. Refer to the following
procedure to install memory modules into the slots on the motherboard.
1. Unlock a DIMM slot by pressing the module clips outward.
2. Align the memory module to the DIMM slot, and insert the module vertically into the DIMM
slot. The plastic clips at both sides of the DIMM slot automatically lock the DIMM into the
connector.
11
Hardware Installation
Installing the Motherboard
The sequence of installing the motherboard into the chassis depends on the chassis
you are using and if you are replacing an existing motherboard or working with an
empty chassis. Determine if it would be easier to make all the connections prior to this
step or to secure the motherboard and then make all the connections. It is normally
easier to secure the motherboard rst.
Use the following procedure to install the I/O shield and secure the motherboard into
the chassis.
Note: Be sure that the CPU fan assembly has enough clearance for the
chassis covers to lock into place and for the expansion cards. Also
make sure the CPU Fan assembly is aligned with the vents on the
covers.
Installing the I/O Shield
The motherboard kit comes with an I/O shield that is used to block radio frequency
transmissions, protects internal components from dust and foreign objects, and
promotes correct airow within the chassis.
Before installing the motherboard, install the I/O shield from the inside of the chassis.
Press the I/O shield into place and make sure it ts securely. If the I/O shield does not
t into the chassis, you would need to obtain the proper size from the chassis supplier.
Securing the Motherboard into the Chassis
Most computer chassis have a base with mounting studs or spacers to allow the
motherboard to be secured to the chassis and help to prevent short circuits. If there are
studs that do not align with a mounting hole on the motherboard, it is recommended
that you remove that stud to prevent the possibility of a short circuit. In most cases, it
is recommended to secure the motherboard with spacers.
1. Carefully place the motherboard onto the studs/spacers located inside the
chassis.
2. Align the mounting holes with the studs/spacers.
3. Align the connectors to the I/O shield.
4. Ensure that the fan assembly is aligned with the chassis vents according to the fan
assembly instruction.
5. Secure the motherboard with screws.
12
AMD 740G/760G/780G motherboard
Connecting Cables and Setting Switches
This section takes you through all the connectors and switch settings necessary on
the motherboard. This will include:
q Power Connectors
v 24-pin ATX Power Connector
v 4-pin ATX_12V Power Connector
q Internal Headers/Connectors
v USB Headers
v Front Pannel Audio Header
v Front Panel Header
v Speaker Header
v Hard Disk Connector
v SPDIF-Out Header
v COM Header
q Serial-ATA (SATA) Connectors
q Fan Connectors
q Expansion Slots
q Jumper Settings
See Figure 1 to locate the connectors and jumpers referenced in the following
procedure.
13
Hardware Installation
J1-Pin Denition
Pin Signal Pin Signal
1 +3.3V 13 +3.3V
2 +3.3V 14 -12V
3 GND 15 GND
4 +5V 16 PS_ON
5 GND 17 GND
6 +5V 18 GND
7 GND 19 GND
8 PWROK 20 -5V
9 +5V_AUX 21 +5V
10 +12V 22 +5V
11 +12V 23 +5V
12 +3.3V 24 GND
24-pin ATX Power Connector
J1 is the main power supply connector. Make sure that the power supply cable and
pins are properly aligned with the connector on the motherboard. Firmly plug the
power supply cable into the connector and make sure it is secure.
4-pin ATX_12V Power Connector
PWR1, the 4-pin ATX 12V power connection, is used to provide power to the CPU. Align the pins
to the connector and press rmly until seated.
PWR1-Pin Denition
Pin Signal
1 GND
2 GND
3 +12V
4 +12V
120
240
121
120
240
121
1.5V
1.5V
.
.
.
J1
1
12
13
24
PWR1
1
14
AMD 740G/760G/780G motherboard
USB Headers
This motherboard contains four USB 2.0 ports that are exposed on the rear panel of
the chassis (Figure 2). The motherboard also contains four 10-pin internal headers
onboard. The onboard headers are optional.
Note. Secure the bracket to either the front or rear panel of your chassis (not all
chassis are equipped with the front panel option).
FP_U1~FP_U4-Pin Denition
PIN Assignment PIN Assignment
1 VCC 2 VCC
3 USBP0- 4 USBP1-
5 USBP0+ 6 USBP1+
7 GND 8 GND
9 KEY 10 NC
120
240
121
120
240
121
1.5V
1.5V
.
.
.
FP_U111FP_U3
FP Audio Header
The audio connector supports HD audio
standard and provides two kinds of audio
output choices: the Front Audio, the Rear
Audio. The front Audio supports re-tasking
function.
Note:
In o rd e r to u ti l iz e th e f ro n t au di o
header, your chassis must have front
audio connector. Also please make
sure the pin assignment on the cable
is the same as the pin assignment on
the mainboard header. To find out if
the chassis you are buying supports a
front audio connector, please contract
your dealer.
FP_S1-Pin Denition
PIN Assignment PIN Assignment
1 MIC2(L) 2 GND
3 MIC(R) 4 -ACZ-DET
5 Front Audio(R) 6 Reserved
7 FAVDIO-JD 8 Key(No pin)
9 Front Audio(L) 10 Reserved
1
FP_S1
FP_U211FP_U4
Loading...