~T~ZONTON
999
Professional
FM Transceiver
THE USER'S MANUAL
We are grateful for your purchase of this transceiver.
We believe this easy-to-use transceiver will provide you
with dependable and reliable communications.
We adopt advanced technology & workmanship for this
transceiver, we trust our aborative design will make it better
&
quicker service for you. For correct use, please read this
manual before use.
MODELS COVERED BY THIS MANUAL
ST-618: VHF FM Transceiver 136-174MHz
ST-618: UHF FM Transceiver 350-390MHz
400-470MHz etc.
The transceiver apply for the software of QXPG-78D
NOTE: For avoiding mistakes, should read the data
first, then program.
Function
Operation
Page
Channel Mode
[DIAL](1 second)+[LOW]
12
Frequency+Channel Mode
[DIAL](1 second)+[DIAL]
12
Frequency Mode
[DIAL](1 second)+[SCAN]
12
Adjust Squelch
[FUNC](1 second)+[LOW]
14
High/Low Power
Press [LOW]
16
Channel Mode and Frequency
Add Channel Scan
+Channel Mode.
17
[FUNC](1 second)+[SCAN]
Scan ON
Press [SCAN]
17
Manually Dialing
Press [PTT] + Digits Key
19
Dial Saved DTMF Numbers
[DIAL]+memory units(1-9)
19
Redial DTMF Numbers
[DIAL]+[O]
19
Save DTMF Numbers
[DIAL]+[#J, input the digits
(16 digits max.)[DIAL]+
20
memory units(1-9)
Confirm Saved DTMF Numbers
[DIAL]+[*]+memory units(1-9)
20
Delete Saved DTMF Numbers
[DIAL]+[D]+memory units(1-9)
20
Key Locked
[FUNC](1 second)+[*]
21
[FUNC](1 second)+[2].
Lightening
Rotate[Circumrotate Encoder]
21
to choose background lights
Reverse Frequency
[FUNC](1 second)+[3]
22
. QUICK-OPERATION liUIDE
Function
Operation
Page
Frequency Mode
Stepping
[FUNC](1 second)+[#)
22
Press[LOW] to choose
stepping level in circle
[FUNC](1 second)+[1].
VOX
Rotate [Circumrotate Encoder]
23
to choose gain level
[FUNC] (1 second)+ [A).Press
[LOW] to choose CTCSS/DCS/
Adjust Receiving
OFF in circle, when in DCS,
CTCSS/DCS Decode
press [DIAL] to choose Normal
24
or Inverted code.Rotate
[Circumrotate Encoder] to
choose code.
[FUNC] (1 second)+[B]. Press
[LOW] to choose CTCSS/DC
Adjust Transmitting
StOFF in circle,when in DCS,
CTCSS/DCS Encode
press [DIAL] to choose Normal
24
or Inverted code.Rotate
[Circumrotate Encoder] to
choose code.
Frequency Mode. [FUNC] (1
second) + OPress[SCAN] to
Slip Frequency
choose +/- slip frequency
25
Rotate[Circumrotate Encoder]
to choose slip frequency value.
QUICK-OPERATION GUIDE
PROMPTION
Function
Operation
Page
Wide/Narrow Band
[FUNC](1 second)+[4]
26
Choose wide/narrow band in circle
Channel Mode and Frequency+Channe
Copy Channel
Mode. [FUNC](1 second)+[C]
26
Rotate[Circumrotate Encoder] to
choose channel, press PIT to save.
Frequency Mode.
Save Channel
[FUNC] (1 second)+[C].
27
Rotate [ Circumrotate Encoder] to
choose channel, press PTT to save.
Channel Mode and Frequency+Channel
Delete Channel
Mode. [FUNC](1 second)+[D]. Rotate
27
[Circumrotate Encoder] to choose
delete channel, press PIT to exit.
Copy Function with
Press[lOW]+[MONI]+Power ON at the
same time. Press [MONI] to transmit
28
Cable
data,then exit to power off and reboot.
The red indicator flashes when
low battery, need to be
transmitting but it can still
communicate
charged
The transmitting will stop when
The voltage of battery is
the red indicator flashes and "Du"
too low. Please charge at
sounds
once!
Out of lock, programmed
"Da da" sounds at intervals. frequency is out of the
range of the transceiver.
The transmitting(last a little while) TOT alert is ON.
will stop when hear "Du" sounds Release PIT to stop the
from speaker. alert tone.
The transmitting(last a little while)
will stop when hear a prompting
TOT alert is ON.
voice.
Set Interval after TOT or
The transceiver transmits after a
TOT resume time. After
while of the TOT alerts.
limited time the transce-
iver can transmit.
When receive signal from other
transceiver,the green light ON.
Press PIT to transmit and "Du"
BCl function is ON.
sounds heard,then retum to receive
signal.
PRECAUTION
For using this transceiver with high safety and efficiency, please
read the following information carefully:
1. Repairing is only for qualified technicians. Please do not dis-
assemble the transceiver causally.
2. Do not modify the transceiver causally.
3. Power off when enter into the flammable and explosive places.
4. Please do not change or charge the battery when under the
flammable and explosive circumstances.
5. Please power OFF the transceiver before entering the explosive
and detonators areas.
6. To avoid the problem caused by electromagnetism interfering
or compatibility,please power OFF when you entering into
the places where is not allowed to use the transceiver,such
as hospitals and airplanes.
7. Please put the device out of the range of the extension of the
airbag in the car.
8. Do not expose the transceiver under sunshine for a long
time,nor place it close to heating appliances.
9. Please keep the antenna at least 2.5cm far away from you
when transmitting.
10.00 not put the device into the dusty,humid and wet areas, nor
put it into the rough surface.
11.lf the device smelled abnormally or smoking,please power
OFF at once,and take out the battery, then contact with the
local distributor.
CONTENT
Unpacking and Checking Equipment·····--------------- 1
Supplied Accessories • - -. - ••• - --- - - - -. - - - - - - - -. - - - - - 1
Standard Accessories • - - - - - - - - - - - - - - - ••• -. - - •• - - -. - - 2
Optional Accessories • - - - - - - - - -- - - - - - - ••••• --. - - - - - - 2
Battery - - - - - - - - - - - .. - - - - .. - - - - .. - - - - - - - - . - - - - - - . -. - ... -
3
Notes •••• - •••• - ••• - •• - - - - -. - - - - - -. - _. - _•• _•• -. -. - - 3
How to Charge - .... - - - - - - - - - - - - - - - -. - - - - _. - - - -. - - - - -- -
4
How to Store - - - - - - - - - - -- - - - - - •- - • - • - -- - - - - - - - -- - -- . 4
Installing the Accessories . -. - - - - - - - - - - --. - - - - - - - ....
5. 7
Installing/Removing the Battery - - - - -. - - - •• - - - -. -. -. - -. 5
Installing/Removing the Antenna - •• -. -. - - -. - - - - -. - - - - - 6
Installing/Removing the Belt Clip - - - - - - - •••• -- - •••••• _. 6
Installing/Removing the Gallus -- - - - - - - -- - - - •••• - - - - - - 7
Installing Exterior Earphone/Microphone - - - - - - - - - - - - -
-·7
Getting Acquainted - - - - - - -... - ... - - - - - - -. -. - - - -. - . -
8. 11
LED Screen • -. - - - - - - - - - - - - - -• -. - - - - - - - - •• _. - - -- - 11
Basic Operation - --- - --- -- -- --- -- .• _.- •. --- ----- -. 12, 16
Power ON/OFF - - - • - - ••• -. -•• -- - - - - - - -. - -- - - - - •• -. - 12
Volume Control-· - ••••• - - - - - - - - - - - - -- -. _. -. - _••• - - - 12
Choose Displaying Mode - - _••• - - - - - - -. -- - - - - - -- - - - 12
Choose Channel - - - - - _•• - -. - - - - - - - - - - -- - - - - - - - _. - - 13
Choose Frequency ------------ ••• - ••• ------------- 13
Squelch - -- - - - • -. - - - - •••• -. _•• - - - - - - -. -••• - • -. - - - - 14
Transmitting' - - - - - -- - - - - - - - - - - - -. -. - --- - - -- -. - - - - - 15
Receiving - - - - - - - - - - -- -. - - _•••• - - - - - -. - - - - - - - - - - - - 15
High/Low Power - -- _. -- - - - - - - -- - - - - - --. - • - _•• _. -- - 16
Advanced Operation ---- --- -- -- -- ----- -- ---- -- --- 17 28
Add Scanning Channel·· - - _•• - - - - - - - - -. - - - - - - - -. - • .' 17
Channel Scanning _. -. _. -- - - - -. - - - - - -. _•• - - -. - •• --. 17
.CONTENT
Frequency Scanning -. - - - - - - - - - - - - - - - - -. - - - - - - -. - - 18
DTMF Calling ---- •• -------.------ •••• -----.-.- 19, 21
Key Locked -- • - - - - - - • - • - - - - - - •• - - - - - - - • - - - -- - - •• - 21
Lightening -- - - - - - - •• -- - - - •• - - -- - ••••• - - - - - - •• - - - - 21
Reverse Frequency - - -- • -. - • - - - - - ••• - - •• - - •• -- - - - -. 22
Stepping .-.------ ••• ------.------ •• --------.----- 22
VOX - -. - - - - - ••• -. - - - - - - •• - -- - - ••• -- - -. -.-. -- - - - - 23
CTCSS/DCS - •• -- - - -. -. - - -. -. -. -. - -- - -. - - - - - -. 23, 25
Slip Frequency. - - - - -. - - - - - •• - -. - - - - ••• - - - - - - •• - - -. 25
Wide/Narrow Band - - -. - •• -. -- - - -. - - - - - -- •• - - - - - - •• 26
Copy Channel - - - - - -. - - -- - -. -. - - - - - - - •• - - - - - -. - - - - 26
Save Channel - - ••• -. - - - -. - - - - - --. -. - - -- - - - - - - - - - -. 27
Delete Channel -. -. -- •- •• - - - - - --. - - - -- - - -. - - - - •• -. 27
Copy Function with Cable - -. - - - - - - •• - - - - - - ••• - - - - - - 28
Auxiliary Operation - --. - -- -- -- •. ---- -- -. -- ---- -. 29, 31
Time-out Timer -- - - - - •• -- -. - -. - ••• -- - - - •• - - - -. -. - •. 29
TOT Pre-caution Time - - - - - - - - - - - - - -. -. - - - -. -. - - - - -. 29
Interval after TOT - - - - • - - -. - - ••••• - - - - - -. - - - - -. - - - - 29
TOT Resume Time·· - - - - - -. -. - - - - - - - - - - - •• - •• - - - -. 29
MONI Key Setting ------.-.-------.----- •• -------.- 29
Busy Channel Lokced •- - - - - - - _. - - - - - - -. - - - - --. - - - - 30
Battery Save - - - ••••• - - - - -• - - - - - -- - - - - - - - - •• - -- • - -. 30
Prompting Voice -- - - ••• - - - - - - - ••• - - - - - -. - - - - -• -. - -. 30
Low Battery Warning -. - - - - - - ••• - - - - -. - •• - - - - - •• - - - - 30
PTT 10 -. - - - -- --. -- ---- --- - .-- -- .:- - - --.-. -. -- --. - 31
Input Information - - - - -. - - - - - ••• -. - - - - •• - - - - - - -. - - - -. 31
Main Technology Parameter··------·-------·--- 32, 33
Trouble Shooting -•.•• ----- •.• ---- •. -.• --- .• --- 34, 35
Carefully unpack the transceiver. We suggest that you confirm the
items listed in the following table before discarding the packing
material. If any items are missing or have been damaged during
shipment, contact with the dealer immediately.
ITEM
QUA!JTiiY?0)
l;h
136-174MHz
Antenna
350-390MHz
1
400-470MHz etc.
Li·ion Battery Charger
1
Adaptor
1
Li-ion Battery (7.4V 1100mAh)
1
Gallus
1
Belt Clip
1
Screws
1
Instruction Manual
1
BATTERY
Please charge the battery before you use it,because it was uncharged
against delivery. The first charging after purchasing orkeeping for more
than 2 months without using cannot achieve normal battery capacity.
After repeating the charge/discharge for 2 or 3 times, the battery can get
to the best performance Please change or charge the battery if low power.
1. Please use the specific charger, other models may cause explosion
and lead to hurt the body.
2. Do not short circuit the battery or put it into fire,nor remove the housing
of the battery.
3. The ambient temperature should between
5"C
and
40"C
while charging.
Otherwise, it may not fUlly charge.
4. Power OFF the transceiver with battery while charging. Using the devic
while charging would affect normal charging.
5. Toavoid interfering the charging, please do not cut off the power or take
out the battery during charging.
6. The battery life will over soon when its operating time decreases even
though it is fully and correctly charged. Please replace the battery.
7. Please do not take out the battery and recharge it after it was fully
charged,otherwise the battery would be damaged or the life would be
shorten.
8. Please do not charge when the battery or the transceiver is damped.
Do it before wipe it up to avoid the hazard.
o
Instruction
Manual
~
~
~
Headset
Speaker/Mic
Speaker/Mic
(QME-01)
(QME-02)
~ ~
®~
~
,~
\
.'/
Programming
Programming
Copy Cable
Software
Cable (QXPL-01)
~
ST-6.5-150V-1
ST-8.5-400V-1
~
ST-8.5-150V-2
ST-10-400V-2
Alwarningl
Whenjewelry, keys or ornamental chain and other electric metals contact
with the battery terminal, the battery maycause damageor hurt bodies.
If the battery terminal short circuitit wi!generatealot of heat, Pleasebe
careful when you bring or use the battery, especially put it into thepocket,
purse or other metal container.
HOW TO CHARGE
1.Plug the AC adaptor into the AC outlet,then plug the cable of
adaptor into the socket at the back of charger. The charger
indicator on GREEN.
2.Plug the Li-ion battery pack or transceiver wifh a Li-ion battery
pack into the charger.
a.Make sure the battery is connected with the charging terminal.
b.The indicator lights RED while charging.
3.When it is 90% charged(about 4 hours),the indicator turns to
LIGHT GREEN (and need to be charged for 2 hours more) ..
4.The indicator turns to GREEN while fully charged.
• After charging the supplied battery for6hours,remove
it
or transceiver
equipped with the battery from the charger. Please do not charge for
over 10 hours,nor placeitin charger for recharging. Over-charging will
shorten the lifeofthe battery and affect its performance .
• Please pay attentiontothe local net power,in ordertosupply different
adaptors.
How to Store
1.lf the battery needs to bestored,itshouldkeep inthe status of 50% charged.
2.lt should be keep in low temperature,dry environment.
3.Keep it far away from heating places,included the place where
the sunshine is too strong.
INSTALLIN THE ACCESSORIES
• Do not shori circuit the battery and put battery into fire.
• Do not
try
to remove the housingofbattery pack.
• Do not install battery in the dangerous circumstance,;t may
cause explosion.
• Do not place them in high temperature placeorput it into fire,
in caseofexplosion.
Removing the Battery:
2. Press the release latch and
slide the pack away from the
transceiver.
The transceiver performs best when the Li-ion battery pack is
fully charged,especially for long-time transmitting or continuo-
usly use.
INSTALLING THE ACCESSORIES
INSTALLING THE ACCESSORIES
CD mtlDt::r:D
CD ••••
em
•••• _a:t
CD
_cu:>cm
Installing the Antenna:
Screw the antenna into the connector on
the top of the transceiver and turn clock-
wise to fasten it.
Removing the Antenna:
Turn the antenna counterclockwise to
remove it.
Plug the gallus into the ring on the right
side of the transceiver,and put the other
side of the gallus into the ring, and then
fasten it.
Installing the Belt Clip:
Aim the screw eyes of belt clip and
the AI. shell of transceiver at each
other,then fasten the belt clip with
the screws.
Removing the Belt Clip:
When remove the belt c1ip,fastening
its fixed screws.
Unveil(not need to take it out)the cover of
J
the MIC-SP jack,then plug the earphonel
"Mic into the jack of earphone/MicWhen
iO .
uSing earphone/Mic,it will affect the perf-
ormance of waterproof.
~@
GETTING ACQUAINTED
GETTING ACQUAINTED
1. Power SwitchNolume Control
Turn clockwise to power ON and adjust volume while turn
counterclockwise to power OFF.
2. LED Indicator
Lights RED while transmitting,lights KELLY while receiving,
flashes RED while in low battery.
3. Circumrotate Encoder
Rotate to select channels, and also work with other function
keys to set functions.
4. [PTT] Switch
Press,then speak into the microphone to transmit, and also
work with other function keys to set functions.
5. [MONI] Key
According to how to program auxiliary functions of this key.
Please refer to P30 of the details instruction,press ON/OFF
the programmable auxiliary function,and also work with other
function keys to set functions.
6. [DIAL] Key
Use to store/confirm/transmitldelete DTMF number,also using
as a function key.
7. [FUNC] Key
Function key,press to unlock other functions setting.
GETTING ACQUAINTED
GETTING ACQUAINTED
8. [SCAN] Key
Press to begin or stop scanning,and also work with other
function keys to set functions.
13
DCS " " " " "
i,
75
100
+
ACT
C, C, C•.O O.C'·
~gl!.I!!
-l!!llil ••••
vox~
R
9. [LOW] Key
Press to choose transmitting in High/Low power,and also
work with other function keys to set functions.
ICON
INSTRUCTION
-
Displays when monitoring the channels
(Squelch ON)
Dsiplays when the selected channels are
A
in the scan list while displays nothing
when the channelis out of scan list.
CI CI CIC'CI CI
Displays the working frequency or
channel number. Select different functions
tI !.I LU"
Lf.!.I
displays different numbers.
IBB
Displays all kinds of numbers as per
selected functions.
R
Displays when the Reverse Frequency
function is ON
VOX
Displays when VOX function is ON.
While receiving, it means signal strength
.....
_---
(the more,the stronger), while transmitting,
it means power(the more,the higher).
[i
DisplayswhenpressingFUNCto setthefunctions
II!]
Displays when transmitting in low power.
+
Displays when Key Locked function is ON.
A
Displays when using narrow band.
CT Displays when CTCSS function is ON.
DCS Displays when DCS function is ON.
a
Displays when selling Slip Frequency function.
75
50
Mantissa of frequency.
.25
10. [DTMF] Keypad
Use to store and transmit DTMF number,and also work with
other function keys to set functions.
11. MIC-SP Jack
Connect earphone/microphone bought by users.
BA!iIC OPERATION
Power ON/OFF
Turn [Power SwitchNolume Control] clockwise to power ON the
transceiver.
Turn [Power SwitchNolume Control] counterclockwise to power
OFF the transceiver.
Volume Control
Rotate [Power SwitchNolume Control] to adjust volume.Turn
clockwise to turn up the volume while turn counterclockwise
to turn down. When adjusting the volume, press MaN I to mo-
nitor the background noise.
• When communicating with others, you need to adjust the
volume correctly.
Choose Displaying Mode
There are 3 kinds of displaying modes for free choice.
Channel Mode
Press DIAL for 1 second (the prompting voice would be heard
if set),"
Iii"
flashes on the screen,then press Law.
• The current channel displays on the screen.
Frequency+ChannelMode
Press DIAL for 1 second,and then press again.
• The current communicating frequency and channel displays
on the screen.
Frequency Mode
Press DIAL for 1 second, and then press SCAN.
• The current communicating frequency displays on the screen.
BA!iIC OPERATION
• Channel mode displays UNPG if any channel hasn't been
programmed. You can only press DIAL to change to frequency
mode.
Choose Channel
This function is valid under the display mode of Channel and
Frequency+ChanneI.Rotate[Circumrotate Encoder] to choose
needed channel.Turn clockwise to increase the channel num-
ber while turn counterclockwise to decrease it.
• When the programmed frequencyofchose channel is out
of
the rangeoftransceiver, it will alert you outoflock.
• The screen displays chose channels.
Choose Frequency
This function is valid only under the display mode of Frequency.
There are 2 ways for free choice.
1. Input frequency
Rotate [Circumrotate Encoder] to choose frequency,turn clo-
ckwise according "stepping" to increase frequency while turn
counterclockwise to decrease it.
• The selected frequency displays on the screen.
• Please select the stepping before circumrotate encoder to
choose frequency (Refer to P22 of "STEPPING'?
BA!iIC OPERATION
2. Input frequency on Keypad
• Press [DTMF],then input the frequency directly.
E.g. linput 4,0,3,0,5,0 when communicating in 403,050MHz,
he screen displays 403,050, that means you can communi-
cate in 403,050MHz.
NOTE: Input frequency on keypad is relatedtostepping,use
Circumrotate Encodertoselect and adjust frequency.
• The input frequency displays on the screen.
• When inputting wrong frequency,press [MON/} to cancel.
• Frequency range and stepping frequencyoftransceiver would
restrict the frequency you inputPlease pay more attention
about the stepping you set.
Squelch
When there is no signal,squelch function can mute loudspeaker.
When squelch function is ON,you will hear the background noise
from the loudspeaker, while the squelch is OFF you will not hear
the background noise. The squelch level you choose will decide
when your squelch is ON/OFF. If the level is too high,you cannot
get weak signal, if the level is too low, the signal will appears in
the background noise.
HowtoAdjust Squelch
1. Press FUNC for 1 second, then press Law.
• The screen displays"_SqL" and the current squelch level.
BA!iIC OPERATION
2. Turn the encoder from O(open) to 9(tightest) to select the
squelch level.
• Turn clockwise to increase the squelch level,turn counter-
clockwise to decrease the squelch level.
3. Press any key to end the setting.
• Return to normal operation.
Transmitting
According to different settings for the monitor function,press
MaN I to monitor the loudspeaker for a moment,and confirm
there is no broadcasting station is transmitting on the selected
channel. Press PTT, and then speak into the microphone.
1. Please keep the microphone approximately 3-4cm from
your mouth,and speak in normal speaking voice to ensure
best performance.
2. When pressing PTT, LED lights RED.
3. Release PTT to receive.
Receiving
If the working channel is called, LED lights Green,you can
receive the call.
• If the signal is weak and you have set the higher squelch
level,you may miss the call.
• Local dealer may program the CTCSS/DCS.You could only
receive calling from the station that selected the same
CTCSS/DCS as yours. Other callings cannot be heard.
BA§IC OPERATION
ADVANCED OPERATION
High/Low Power
For tansmitting in high power,large waste in battery, thus it dose
not need high power in short distance communication, we can
choose low power to save battery, while we use high power
when in long distance communication. Press LOW to choose
High/Low power.
• Low power,displays "LO" on the screen while high power
displays nothing.
Add Scanning Channel
This function is valid only under the display mode of Channel
and Frequency+Channel.You can choose channels for scanning.
1.
Rotate [Circumrotate Encoder] to choose add scanning cha-
nnels.
2. Press FUNC for 1 second to set the function ON.
• "F" flashes on the screen .
3. Press SCAN to add/cancel the added scanning channels.
• The channel displays "A" on the screen while it is added
to scan.
• The channel displays nothing while it is not added to scan.
Repeat the above operation,channel will alternate between
scan and non-scan.
Channel Scanning
This function is valid only under the display mode of Channel
and Frequency+Channel, which is used to monitor every added
scanning channel of the transceiver. When scanning, the trans-
ceiver will check every channel and only stop in the channel
with signal.
ADVANCED OPERATION
1. Press SCAN to begin scanning.
• Scan starts from current channel,and channel number
increases gradually. Screen displays "SCAN".
• The transceiver will stay in the communicating channel until
the signal disappears. Scan will return after signal disapp-
ears for 4 seconds, unless there is new signal appears
within these 4 seconds.
2. Press any key except MONI to end scanning.
Frequency Scanning
This function is valid only under the display mode of Frequency.
It is used to monitor the signal in every frequency of the step-
ping.When scanning,transceiver will check the increased step-
ping and only stop in the frequency with signal.
1. Press SCAN to begin scanning.
• Scan starts from current frequency,and increases according
to the stepping.
• Screen displays "SCAN"
When the increased frequency range is out of transceiver frequency,
it will turn to the lowest frequency to increase as per "stepping".
The transceiver will stay in the communicating frequency until
the signal disappears. Scan will return after signal disappears
for 4 seconds, unless there is new signal appears within these
4 seconds.
• When scan quit in a specific frequency, the screen displays
frequency rate, the dot between frequency will flash on the
screen.
2. Press any key except MONI to end scanning.
ADVANCED OPERATION
DTMF Calling
Manually Dialing
Press PTT, and then enter the needed numbers.
• Press PIT,then enter the first digit you input,release PIT,
and then release the digits keypad,the transceiver will keep
transmitting within 2 seconds,you need not keep pressing
PTTto dial.
• When transmitting DTMF, microphone will be muted,you can
monitor the double-audio-frequency through loudspeaker.
Automatically Dialing
Dial Saved DTMF Numbers
Dial saved DTMF number of the memory number units.
1. Press DIAL to enter the dial-up mode.
• Screen displays "__ d"
2. Input the dialed memory number units
(1-9)
• Screen displays and scrolls the calling numbers and
sounds DTMF.
3. Return to the former display automatically.
Redial DTMF Numbers
Redial the last transmitted DTMF number (16 digits max.)
1. Press DIAL to enter the dial-up mode.
• Screen displays "__ d"
2. Press [0] to dial the last transmitted number.
• Screen displays and scrolls the calling numbers and
sounds DTMF.
3. Return to the former display autimatically.
ADVAI\ICED OPERATION
Save
DTMF
Numbers
1.
Press DIAL to enter the dial-up mode.
• Screen displays "__ d"
2. Press [#] to enter the store mode.
3. Enter the numbers in the DTMF keypad.
• If you input incorrect number, press -MaN I to clear it and
enter the correct one.
4. Press DIAL after input the digits, and then enter digits of the
memory channel numbers
(0-9).
• Return to the former display.
Confirm Saved
DTMF
Numbers
Check the memory channel number units.
1.
Press DIAL to dial-up mode.
• Screen displays "__ d"
2. Press [*] to enter confirmed saved mode.
3. Enter the needed memory number units
(1-9)
• Screen displays and scrolls the saved DTMF numbers
and sounds correspongding DTMF.
4. Return to the former display automatically.
Delete Saved
DTMF
Numbers
Delete the memory channel number units.
1.
Press DIAL to enter the dial-up mode .
• Screen displays "__ d"
2. Press [0] to enter the delete mode .
• Screen displays "c1r_d"
Press any key except digit keys from 1 to 9 to cancel the
operation.
ADVANCED OPERATION
3. Input the needed delete DTMF numbers
(1-9).
• The selected DTMF numbers were deleted.
4. Return to the former display automatically.
Key Locked
This function is to avoid operating transceiver incorrectly,to lock
keypad of the transceiver.
1.
Press FUNC for1second, the function is ON.
• "Iii "flashes on the screen.
2. Press [*] to enter Key Locked.
• "+" displays on the screen.
• When key locked function is ON, all the keys are invalid
except PTT,MONI,FUNC.
To unlock keypad of the transceiver, please repeat the above operation.
Lightening
You can set the lightening function to be automatism, connec-
tion or off.
1.
Press FUNC for1second, the function is ON.
• "Iii" flashes on the screen.
2. Press [2] to select lightening function.
3. Rotate [Circumrotate Encoder] to select the needed setting.
• Displays "A" for automatism. The light on screen will light
for 5 seconds when press any key except PTT and MONI,
and then put out automatically.
• Displays "ON" for connection. The light on screen will light
when the transceiver is power ON.
• Displays "OFF" for cutting off. The light on screen will not work.
4. Press any key to end setting,and return to the former display.
ADVANCED ,OPERATION
Reverse Frequency
Transmitting and receiving frequency will reverse when using
the reverse frequency function. It means to transmit with receiv-
ing frequency, to receive with transmitting frequency. If set CTCS
SIDCS function,encoding and decoding signal will also reverse.
1. Press FUNC for 1 second, the function is ON.
• "F" flashes on the screen.
2. Press [3] to set reverse frequency function ON.
• Screen displays "R"
While changing channel/frequency or scanning, the reverse
frequency function is OFF.
3. Repeat the above operation,the channel will alternate
between ON/OFF reverse frequency.
Stepping
This function is valid only under the mode of full range of Fre-
quency. Setting setpping would restrict the transceiver choos-
ing frequency and frequency scanning.
1. Press FUNC for 1 second, the function is ON.
• "[ii "
flashes on the screen.
2. Press [#] to select stepping frequency.
• Screen displays the current stepping frequency.
3.
Press LOW to choose stepping frequency in circle.
5 means stepping is 5KHz
6.25 means stepping is 6025KHz
12.50 means stepping is 12.50KHz
25 means stepping is 25KHz
50 means stepping is 50KHz
1.000 means stepping is 1.000KHz
10.000 means stepping is 10.000KHz
4. Press other key to end setting,and return to the former display.
ADVAI\ICED OPERATION
VOX
This transmitting function can communicate hands-freely. When
using VOX, if microphone's gain is higher than VOX gain,
the transceiver will turn to transmitting mode automatically while
return to receiving mode after 2 secends if microphone's gain is
lower than VOX gain. Owing to switching between transmitting
and receiving, we suggest not transmit when setting VOX gain if
the surrounding is too noisy.
1. Press FUNC for 1 second, the function is ON.
• "F" flashes on the screen.
2. Press [1] to enter VOX function.
• "VOX" flashes on the screen,at the same time the top right
corner of the screen displays the current VOX transmitting
gain.
3. Rotate [Circumrotate Encoder] to select the VOX transmitting
gain from "OF" to "3".
• Turn clockwise to increase VOX transmitting gain while turn
counterclockwise to decrease it.
• Screen displays "OF" when VOX is OFF. "1" means low gain,
"2" means middle gain, "3" means high gain.
4. Press any key to end setting.
• Screen displays "VOX" when select the gain from 1 to 3 and
displays nothing when VOX function is OFF.
CTCSS/DCS
When the channel setting CTCSS/DCS code,the squelch func-
tion ON only received the corresponding CTCSS/DCS code.
And, the transceiver which has the same CTCSS/DCS code
can receive the signal you transmit.
ADVAI\ICED OPERATIOI\I
• Program CTCSS/DCS code in your transceiver can help
you to ignore (not hear)some unnecessary callings from
ther transceiver. But that not means your calling is privacy.
Adjust Receiving CTCSS/DCS Decode
1. Press FUNC for 1 second,the function is ON.
• "F" flashes on the screen.
2. Press [A) to adjust receiving CTCSS/DCS decode.
• Screen displays the current code.
3. Press LOW to select the mode of CTCSS/DCS/OFF in circle.
• Displays "q" before the digits when select CTCSS code,
displays "d" before the digits when select DCS code, select
"OFF" to delete.
• When select DCS code, press DIAL to choose Normal or
Inverted code. Inverted code displays" - " while Normal
code displays nothing.
4. Rotate [Circumrotate Encoder] to select new CTCSS/DCS
code.
5. Press any key except PTT and MONI to exit and store the
adjusted code.
• Set CTCSS decode,screen displays "CT" while receiving.
Set DCS decode, screen displays "DCS" while receiving.
Set OFF,screen displays nothing.
Adjust Transmitting CTCSS/DCS Encode
1. Press FUNC for 1 second, the function is ON.
• "~ "flashes on the screen.
2. Press [B) to adjust receiving CTCSS/DCS encode.
• Screen displays the current code.
ADVAI\ICED OPERATIOI\I
3. Press LOW to select the mode of CTCSS/DCS/OFF in circle.
• Displays "q" before the digits when select CTCSS code,
displays "d" before the digits when select DCS code, select
"OFF" to delete.
• When select DCS code, press DIAL to choose Normal or
Inverted code. Inverted code displays" - " while Normal
code displays nothing.
4. Rotate [Circumrotate Encoder) to select new CTCSS/DCS code.
5. Press any key except PTT and MONI to exit and store the
adjusted code.
• Set CTCSS decode,screen displays "CT" while transmitting.
Set DCS decode,screen displays "DCS" while transmitting.
Set OFF,screen displays nothing.
Slip Frequency
This function is valid only under the display mode of Frequency,
setting the slip frequency of receiving and transmitting it.
1. Press FUNC for 1 second, the function is ON.
• "~" flashes on the screen.
2. Press [0) to set slip frequency.
• Screen displays the current slip frequency status.
3. Press SCAN to select +/- slip frequency.
• " 13"
displays before the frequency when it is - slip frequ-
ency, while + slip frequency displays nothing.
4. Rotate [Circum rotate Encoder) to increase/decrease slip
frequency as per the stepping.
• Screen displays slip frequency.
5. Press other key to exit and store the setting.
ADVANCED OPERATION
Wide/Narrow Band
The user can set transceiver to communicate in wide/narrow
band freely according to different countries.
High volume but big distortion when the transceiver with wide band
talk to the transceiver with narrow band,and squelch switches OFF
as
the increasing of volume. Low volume but large noise when the
transceiver with narrow band talk to the transceiver with wide band.
1. Press FUNC for 1 second to set the function ON.
• "1:iI
"flashes on the screen.
2. Press [4] to select Wide/Narrow band.
• Narrow band displays" .•. " on the screen while wide band
displays nothing.
Repeat the above operation to choose Wide/Narrow band in circle.
Copy Channel
This function is valid only under the display mode of Channel
and Frequency+Channel. Copy one channel data of the
tranceiver to other channel.
1. Select the needed copy channel.
2. Press FUNC for 1 second to set the function ON.
• " I:iI
"flashes on the screen.
3. Press [C] to select the saved copy channel.
• Screen displays the saved channel.
4. Rotate [Circumrotate Encoder] to select the channel.
• Press any key except [PTT] to exit but not store.
5. Press PTT to store and exit.
• Now the initial channel data is the same with saved channel data
ADVANCED OPERATION
Save Channel
This function is valid only under the display mode of Frequency.
Program receiver channel when the transceiver without any ext-
erior equipment.
1. Enter the Frequency mode. Select the frequency,slip freque-
ncy,encode/decode signal,etc.
2. Press FUNC to set the function ON.
• "1:iI
"flashes on the screen.
3. Press [C] to select the saved channel.
• Screen displays the saved channel.
4. Rotate [Circumrotate Encoder] to select the saved channel.
• Press any key except PTT to exit but not store .
5. Press PTT to store and exit.
• The programmed data under full range of Frequency mode
was stored in the saved channel.
Delete Channel
Delete the programmed channel data of the transceiver.
1. Press FUNC for 1 second, the function is ON.
• "1:iI "
flashes on the screen.
2. Press [0] to select the deleted channel.
• Screen displays the deleted channel.
3. Rotate [Circumrotate Encoder] to select the needed delete
channel.
• Press any key except PTT to exit but not store.
4. Press PTT to store and exit.
• This channel data was deleted and never displays besides
you reprogrammed it.
ADVANCED OPERATION
Copy Function with Cable
Copy function with cable is that copying the data from a trans-
ceiver to another transceiver without any exterior equipment.
• This function is ON only when the local distributor set
it for you.
1.Power off the main transceiver. Press [LOW] and [MONI] at
the same time to power on and enter into the copying status.
The screen displays "COPY".
2.Repeat STEP 1 for the target transceiver. The screen displays
"COpy" too.
3.Connect the two transceivers with specified copying cable.
4.Press [FUNC] of the main transceiver to begin to copy. The
screen displays "COPY-t", sending its data to the target
transceiver.
S.The two transceivers display "COpy" when finishing the
copying and back to copying stand-by status. If it is needed
to copy to another target transceiver, the target transceiver
should enter into copying status first, and then repeat STEP
3 and STEP 4. Repeat the operations for multi-transceivers.
6.Restart the power again when finishing copying, and the
machine will back to normal working status.
• When in stand-by status, displays COPY.
• When in receiving status, displays COPY-r.
• When in transmitting status, displays COPY-I.
AUXILIARY OPERATION
Adopt OXPG-78D(Software) and OXPG-01
(Program cable) to program.
Time-Out Timer
The purpose of the Time-out timer is to prevent any single
person from using a channel for an extended period of time. If
you continuously transmit more than limited time, the transceiver
will stop transmitting and an alert tone will sound. To stop the
tone, release PIT.
• Pre-caution before TOT: The alert tone sounds before the
limited TOT time of the transceiver.
• Interval after TOT: It is interval after limited TOT time you
have set. You cannot transmit during this interval.
• TOT resume time: Pre-set TOT resume time,when this
function is on,you can not transmit before TOT resume time.
Only when resume time arrives,then can transmit again.
[MONI] Key Setting
MONI key can be set as the following auxiliary functions.
• Squelch OFF(Default setting)
Press to hear the background noise,release to return the
normal operation. It is used to get the weak signal which you
can't get even operated correctly.
• None( No function)
No operation if press.
• Activate Monitor
Press to set CTCSS/DCS OFF, press again to return normal
.operation.
AUXILIARY OPERATION
• Monitor Momentary
Press to set CTCSS/OCS OFF, release to return normal
operation.
Busy Channel Locked
When this function is ON, it can avoid interfering other stations
of the same channel using with yours.When press PIT, if the
channel is being used,your transceiver will alert, and return to
the receiving status.
Battery Save
The battery save function is ON when a signal is not being
received and no operations are being performed(no keys are
being pressed,and no switches are being turned).And it can
decrease the amount of power used.While the channel is not
busy and no operation is performed for 5 seconds this function
is ON,and while a signal is received or an operation is perfor-
med this function is OFF.
Prompting Voice
You can choose prompting voice ON/OFF. This covers all
prompting voice of the transceiver.
Low Battery Warning
Low battery warning alerts you when the battery needs to be
charged or changed. If low power, when transmitting, the ind-
icator flashes and it can transmit continuously. If the voltage is
too low, when transmitting, the indicator flashes and an alert
AUXILIARY OPERATION
tone sounds,stop transmitting and the indicator flashes.Please
change or charge the battery.
PTT 10 is used to continue or stop some repeaters and telephone
system. Press PIT to transmit 10 signal if set begin transmitting.
Release PIT to transmit 10 signal if set stop transmitting.Press
PIT then release it to transmit 10 signal if set begin and stop
transmitting signal.
Input Information
You can write your own information(64 characters max.) storing
in the transceiver.
MAIN TECHNOLOGY PARAMETER
136-174MHz
Frequency Range 350-390MHz
400-470MHz etc.
Working Temperature
-20'C -+55'c
Frequency Synthesization
PLL
Working Voltage
DC7.4V
(2 Rechargeable Li-ionbattery)
Number of Channels
128 Channels
Antenna Configuration
Coil Loaded Antenna
Antenna Impedance
500
Working Way
Simplex in same channel
Simplex in different channel
Grounding
Cathode
Size
1OOmmx 52mm x 27mm
Weight
230g
Output Power
Modulation
Max. Fre. Deviation
Residual Wave
Radiation
Pre-emphasis
Transmitting Current
High power 4W, Low power 1 W
FM
Wide..;;±5KHz Narrow";;±2.5KHz
6dB
High";; 1200mA Low..;;600mA
MAIN TECHNOLOGY PARAMETER
Receiving
-
Sensitivity
Wide band <0.18JN (12dB SINAD)
Narrow band<0.25jlV
Squelch Sensitivity
0.18jlV
Intermodulation
60 dB
Interference
Audio Power
;;'0.5W
Receiving Current
..;;200mA
Squelch Standby
20mA
Current
Trouble
!ihOO1:ing
Trouble phenomenon
Shooting method
Maybe out of battery, please charge
No power
or replace it.Maybe the battery is
not correctly installed, try again!
Check whether the frequency and
Unable to talk with others
CTCSS is same as that of other
in the group
members,whether other members
are in valid communication distance
of transceiver.
There is disturbance from
Please modify CTCSS,also signal
other members.
order of other members or to work
in other frequency.
The battery life is short ev- The battery's life is over, replace
en after correctly charged. with a new one.
Noisy after being
Squelch is open when programming
non-professional users please do
programmed
not modify parameters causally
Some regulated"Da da da" Some errors happen when program
sounds after being
it.Maybe it is out of working
programmed
frequency range.
The transceiver can't scan
Haven't programmed the channel
into the scan list
There is no sound after using
Something wrong with ear bud (send
the earphone for a period. it to distributor for reparation.)
Communication distance
Whether the antenna and its conn-
closer and sensitivity
ector is complete,whether set to be
weaker.
in low power(send it to distributor
for reparation)
Trouble phenomenon
Shooting method
It can receive but not
Check PTT key.
transmit.
(Send it to distributor for reparation)
Power off often
Check whether the connector of
battery is complete.
The voice is too low,and
Check whether the MIC jack is block
often cut off.
with something.(Send it to distributo
for reparation)
Out of communication distance, or
Receiving signal unconsci-
block with high buildings, or using it
ously,and with big noise.
in the underground building. (Send
it to distributor for reparation.)
Speaker with "Ka ka"
Check whether there is something
sound after using for a
on the cover of speaker.(Send it to
period of time. distributor for reparation.)
No sound from speaker
Check whether it is in Min. volume.
(Send it to distributor for reparation.)
Loading...