Page 1
©2017 ZONEFIRST® | 6 Aspen Drive – Randolph, NJ. 07869-1103 | Telephone: 201-794-8004 | Fax: 201-794-1359
www.zonefirst.com | info@zonefirst.com
Controlling Your Comfort Room by Room
The ZD series are extruded aluminum parallel blade dampers
compete with a Power Open Power Close Plug-In Motor. These
dampers are shipped complete and ready for installation. The
lightweight ZD can be installed in any position in any properly sized
duct. These dampers are rated for duct pressure up to
2.0” W.C.
Dampers are available all in even sizes from 8”x8” to 36”x24”. All
dampers are 1/4” undersized from their listed size. Dampers are
ordered as ZDSP for side mount, width by height, as the motor
and end plate will be on the smaller dimension, for typical insertion
into the side/shorter dimension of the duct. The ZDBP denotes
bottom mount and is ordered height by width. The motor and
end plate are on the longer dimension for typical insertion into
either the bottom or top of the duct. Dampers are ordered as
ZDSPwwhh or ZDBPhhww, using 2 digits for each dimension. All ZD
dampers are shipped in the Open position ready for installation.
A 12 Volt DC damper motor, Model MP12M, powers the damper
closed and open. The MP12M motor wires by simply plugging
the motor in using the modular cord, supplied with each
damper. The modular cord is a 25’ length of standard four (4)
conductor telephone wire with RJ11 jacks on each end. The
motor is complete with 2 jacks allowing you to daisy chain up to
10 dampers per zone.
The MP12M motor has been tested to over 1,000,000 cycles to
provide long life. Even replacing the motor is a simple less than
one (1) minute change by l oosening the setscrew holding the
motor onto the damper, slide the motor off the damper shaft,
place a new one on and secure with the screw.
The MP12M motor also has a two-color Light Emitting Diode (LED)
to indicate the damper position. When the LED is GREEN the
damper is Open. When the LED is RED the damper is Closed.
When the LED is not lit the motor is typically moving between open
and closed. The motor cycles between open and closed in less
than 5 seconds
Actuator & 25’ of modular cord included with each damper
Minimum Position
Adjustment
Simply open the cover to
minimum position setting.
With a screwdriver, loosen
the setscrew and adjust
your setting to desired
position.
ZONE DAMPER
With MP12M Plug-In Motor
Model: ZDSP & ZDBP
ZDSP Side
Mount
ZDBP-Bottom Mount
Dimensional Drawing (nominal)
Damper Specifications
Construction – Aluminum Mill Finish, Mitre Angles
Linkage – Zinc plated linkage arms, Delrin bushings
Dimensions – 8”x8” to 36”x24” in 2” increments, 1/4” undersized.
Custom sizes also available
Motor Voltage – 12VDC, 0.100A
Torque – 7.0 in/lbs, 112.0 in/oz, 0.79NM
Temperature Rating - 0 F to 150 F Operating, -13 F to 150 F Storage
Humidity – 5% to 95% Non-Condensing
Damper Timing – Nominal 5 Sec. Powered Open-Closed \
Connection - Modular RJ11, 2 Ports
Duct Pressure – Maximum 2”W.C.
Page 2
©2017 ZONEFIRST® | 6 Aspen Drive – Randolph, NJ. 07869-1103 | Telephone: 201-794-8004 | Fax: 201-794-1359
www.zonefirst.com | info@zonefirst.com
NOT USED
POSITIVE (+)
NEGATIVE (-)
POSITIVE (+)
NOT USED
-12VDC
VDC
-12VDC
NOT USED
POSITIVE (+)
NEGATIVE (-)
POSITIVE (+)
NOT USED
+12VDC
VDC
+12VDC
INSTALLATION
1. Cut a 4-inch (102-millimeter) opening in one side of the air
duct at the location selected. Ensure the opening is cut fully to
the top and bottom air duct seams.
2. Slide the damper into the cut opening of the air duct. Ensure
the electric actuator is mounted toward the top of the air duct.
3. Secure the damper mounting plate to the air duct with the
sheet metal zip screws provided.
Side Mount:
CHECKOUT
To checkout the operation of the dampers the control
panel needs to be operating. I t is recommended that
each damper be checked before installing into the duct.
To check the damper, plug the damper into a zone on
the control panel. Each zone of the panel has an LED
that will be Green when the damper is to be open. When
the panel LED is off, the damper will close and the
damper LED will turn RED.
All dampers are 100% factory tested with the cord
provided with each damper.
OPEN CLOSE
The damper shaft is square
however the motor has a
small triangular shape that
also indicates the position of
the damper. If the LED does
not light, this will indicate the
damper is either opening or
closing. The damper may be
closed and the LED not lit Red
as the damper may have
stopped short of full closed
due to the roundness of the
damper.
Bottom Mount:
TROUBLESHOOTING
If the damper LED does not light and the motor is not moving when
plugged into the control panel, unplug and retry plugging in
again. Until the motor moves and the LED lights. Make sure
the cord is not pinched or broken.
The motor is powered by 12VDC from the panel. Check the
connector on the panel for 12VDC as shown below.
MOTOR
PLUG
The power to the dampers
can be checked with a
voltmeter measuring
12VDC. Check the
and any wire the same
way by checking the
inside negative pair of
wires with the outside
positive pair of wires.
+12VDC
VDC
-12VDC
VDC
POSITIVE (+)
NEGATIVE (-)
POSITIVE (+)
NOT USED
DAMPER OPEN
MOTOR
PLUG
NOT USED
POSITIVE (+)
NEGATIVE (-)
POSITIVE (+)
NOT USED
DAMPER CLOSED
Loading...