Page 1
CV-TYQ_0120_E_20180329
20
VE HYBRID ELECTRIC
DISPENSING POT
SGPHKG
CV-TYQ40
BC
A
WARNING - THIS APPLIANCE MUST BE EARTHED
How to change the Fuse
If the Power Plug of your Power Cord (See P.4) is,
A. A type that can be disassembled. Refer to above.
B. A solid molded type that can not be disassembled. Please refer to the following.
1. Open the Fuse Cover of the Power Plug.
2. Replace the Fuse (13A) that is inside with a new Fuse. (Be sure to replace
with a 13A Fuse)
3. Fit back the Fuse Cover with the new Fuse to the Power Plug.
Do not connect the Fuse directly to the Power Plug. The Fuse
Cover can not be attached.
GREEN AND YELLOW
13 AMP FUSE
BROWN
BLUE
IMPORTANT
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow:Earth Brown:Live Blue:Neutral
If the colours of the wires in the mains lead of this appliance do not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows.
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the
letter E or by the earth symbol or coloured green or green-and-yellow. The wire which is coloured blue must be
connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured brown must be connected to the terminal which is
marked with the letter L or coloured RED.
This appliance must be protected by a 13A fuse if a 13A (BS1363) plug is used
or, if any other type of plug is used, by a 10A fuse either in the plug or adaptor
or at the distribution board.
Caution
Power Plug
Fuse Cover
Fuse
(13A)
Fuse Cover
Always follow basic safety precautions when using electrical appliances.
Read all instructions carefully.
Please keep this instruction book on hand for easy reference.
INDEX
BOIL MODE
DISPENSE HOT WATER
DISPOSE WATER
AUTOMATIC SHUT-OFF FUNCTION
REBOIL MODE
HOW TO SET THE KEEP WARM MODE
QUICK TEMP MODE
ENERGY-SAVING MODE
ENERGY-SAVING TIMER FUNCTION
CAFÉ DRIP FUNCTION
HOW TO CHANGE THE INFORMATION
SOUND
6
8
8
9
9
10
12
13
13
14
14
IMPORTANT SAFEGUARDS
PARTS NAMES AND FUNCTIONS
2
4
HOW TO USE
BEFORE USE
USEFUL FUNCTIONS:
●
The average Keep Warm electric power consumption is for one hour, provided that the Inner
Container is full and the room temperature is approximately 23｡C.
●
The height refers to the product when the handle is down.
●
In high altitudes or severely cold areas, the product may not perform as specified. Avoid using the
product in such areas or in other extreme conditions.
●
This product is not suitable for use in countries or regions with different power supply voltages or
frequencies.
SPECIFICATIONS
CD-TYQ40
AC 220-230V 50/60Hz
640-700W
0.75 m
Approx.
24
W
Approx.
21
W
Approx.
17
W
Approx.
13
W
4.0 liters
98｡C
90｡C
80｡C
70｡C
Model No.
Capacity
Rating
Electric Consumption
Length of the Power Cord
Weight (including the Power Cord)
External Dimensions (approx. cm)
Average Power
Consumption
during Keep
Warm
21 (W) x 28.5 (D) x 35 (H)
Approx.
3.2
kg
Q&A ON PRODUCT USE
TROUBLESHOOTING GUIDE
SPECIFICATIONS
CLEANING AND MAINTENANCE
BEFORE CALLING FOR SERVICE
17
17
20
CLEANING AND MAINTENANCE
HOW TO REPLACE THE
INNER LID GASKET
15
15
REPLACEMENT PARTS
17
16
HOW TO CLEAN THE INNER
CONTAINER WITH CITRIC ACID
●
Page 2
CV-TYQ_0203_E_20180126
2 3
IMPORTANT SAFEGUARDS
These WARNINGS and CAUTIONS are intended to protect you and others from personal injury and
household damage. To ensure safe operation, please follow carefully.
Do not use a power source other than 220-230 V AC.
Use of any other power supply voltage may cause fire
or electric shock.
If the blades or surface of the Power Plug become
soiled, wipe them clean.
A dirty Power Plug may cause fire.
Do not tilt the product or tip it over.
Hot water may spill from the Spout or Steam Vent,
even if the Automatic Dispense Lock is on.
Do not slam the Upper Lid when closing.
Hot water may dispense or spill out, resulting in scalds.
Do not modify the product. Only a repair technician
may disassemble or repair this unit.
Attempting to do so may cause fire, electric shock or
injury. Make any repair inquiries to the store you
purchased the product.
Do not use the product as a cooler or place ice
inside of it.
Doing so may cause condensation, resulting in electric
shock or breakdown of the product.
Insert the Power Plug completely and securely
into the electrical outlet.
A loosely inserted Power Plug may cause electric
shock, short circuit, smoke or fire.
Do not allow infants or children to put the
Appliance Plug in their mouth.
Doing so may cause electric shock or injury. Take
special precautions with children and infants.
Do not allow the end of the Appliance Plug to
become soiled with dust or come into contact with
any metal objects.
Doing so may cause electric shock, short circuit or fire.
Do not damage the Power Cord.
Do not bend, pull, twist, fold, or attempt to modify the
Power Cord. Do not place it on or near high
temperature surfaces or appliances, under heavy items
or between objects. A damaged Power Cord can cause
fire or electric shock.
Do not use the product if the Power Plug or Power
Cord is damaged or if the Power Plug is loosely
inserted into the electrical outlet.
Doing so may cause electric shock, short circuit or fire.
Do not fill over the Maximum Water Level Line.
Overfilling may cause hot water to spill out, resulting in
scalds.
Do not cover the Steam Vent with anything such
as a dishcloth.
Hot water may spill out, resulting in scalds. It may also
cause deformation or discoloration of the Upper Lid or
breakdown of the product.
Do not plug or unplug the Power Cord if your
hands are wet.
Doing so may cause electric shock or injury.
Do not allow liquid to come into contact with the
Receptacle or Power Cord.
Doing so may cause short circuit or electric shock.
Do not touch the Steam Vent or bring your hands
or face near the Steam Vent.
Doing so may cause burns or scalding. Take special
precautions with children and infants.
Always remove the Upper Lid before disposing
hot water.
The Upper Lid may fall off and cause hot water to splash,
resulting in scalds.
Do not tilt or shake the product or carry in your
arms. Do not move it or drain hot water by holding
the Upper Lid.
Doing so may result in scalding by hot water spilling out
from the Spout or Steam Vent, even if the Automatic
Dispense Lock is on. Always use the handle when
carrying.
Do not allow children to use the product
unsupervised. Keep it out of the reach of infants.
Children are at risk of burns, electric shock or injury.
Do not immerse the product in water or splash it
with water, and do not put it on a wet surface such
as a sink.
Doing so may cause short circuit or electric shock.
Use only an electrical outlet rated at 10 amperes
minimum, and do not plug other devices into the
same outlet.
Plugging other devices into the same outlet may cause
the electrical outlet to overheat, resulting in fire.
Do not boil anything other than water.
Attempting to boil, cook, or heat up the following items
may cause bubbling or boiling over, which may cause
scalding. Doing so may also cause clogging of the
water route or Electric Pump, or scorching or corrosion
of the Inner Container.
・
Milk, sake, soup, charcoal, tea bags or tea leaves.
・
Instant food.
・
Food and sauce pouches or foods in plastic bags.
Do not remove the Upper Lid while boiling.
●
The illustrations used in these Operating Instructions may vary from the actual product you have purchased.
Replace the Inner Lid Gasket if it hardens, changes
shape, turns white, or otherwise becomes worn out.
Hot water may spill out when the product is tilted or
tipped over accidentally, and may cause scalding.
Steam may also leak out from the gap and cause burns
or product failures.
Close the Upper Lid securely.
Hot water may spill out when the product is overturned,
resulting in scalds.
Do not use the product near walls or furniture.
Steam or heat may damage, discolor or deform walls or
furniture.
Do not use other Power Cords than the one provided.
Do not use the Power Cord for other appliances.
Do not use the Power Cord for overseas models.
Doing so may cause malfunction or fire.
Do not touch hot surfaces during or for a short
period of time after use.
Touching hot surfaces may cause burns. Be especially
careful with metal parts such as the Inner Lid and the
Inner Container.
Please allow the product to cool down before
cleaning.
Touching hot surfaces may cause burns.
Do not touch the Lid Lock when carrying the product.
Doing so may cause the Upper Lid to open, resulting in
injuries or scalds.
Do not swivel or move the product while
dispensing water.
Hot water may splash out, resulting in scalds.
Always unplug the product by holding the Power
Plug, not by pulling the Power Cord.
Pulling the Power Cord to unplug the product may
cause electric shock, short circuit or fire.
If the Power Cord is damaged, it must be replaced
by an appropriate cord or assembly made
available by the manufacturer or its service agent.
Always use caution when opening the Upper Lid
and avoid skin contact with steam.
Loose water or steam may escape upon opening the
Upper Lid and cause scalds.
Do not attempt to dispense hot water while it is
boiling.
Hot water can spurt out, resulting in scalds.
Do not place or use the product on unstable surfaces.
Doing so may cause scalds or injuries.
Do not use on surfaces that are sensitive to heat.
Doing so may cause fire.
Unplug the Power Plug from the outlet when the
product is not in use.
Leaving the Power Plug in an outlet may cause the
insulation to become damaged, resulting in electric
shock, short circuit or fire, or result in injuries or scalds.
Do not operate the product when it is empty.
Doing so may burn or damage the product.
Avoid using the product near a radio, TV, computer, etc.
The product may cause interference with certain electronics.
Do not drag the product over any surface while
attempting to move.
Doing so may cause damage to surfaces such as
countertops.
Do not place the product over direct flame (such
as a gas stove top), or on top of electric or
induction heating (IH) cookers.
Doing so may cause fire, breakdown or damage of the
product.
Do not use the product where its steam may come
into contact with other electrical appliances.
The steam may cause fire, malfunction, discoloration or
deformation to other electrical appliances.
This appliance is intended to be used in
household and similar applications such as;
Do not allow hot water to come into contact with
the Control Panel or the Water Level Gauge.
Doing so may cause breakdown of the product.
Allow the product to dry completely when storing
the product for a long period of time where it may
freeze.
If water left inside freeze, it may cause breakdown or
malfunction.
Avoid letting steam make contact with cabinets and
walls when using near or under a kitchen shelf.
Doing so may cause discoloration or deformation.
Avoid rough handling, dropping or bumping the
product.
Doing so may cause damage or cease operation of the
product.
IMPORTANT
Stop using immediately if you notice any of the following symptoms
indicating a malfunction or breakdown.
Continued use of the product may cause smoke, fire, electric shocks or injury.
・
The Power Plug or Power Cord has become very hot.
・
The Power Cord is damaged or the electricity turns on and off when touched.
・
The Body is deformed or unusually hot.
・
Smoke is arising from the product or there is a burning smell.
・
Some parts of the product is cracked, loose or unstable.
・
The product emits steam for at least 10 minutes continuously and does not
turn to Keep Warm mode.
・
Water leaks from the Body.
If any of the above occurs, unplug the product immediately and return to
the store where you purchased it for check-ups and/or repairs.
This product is not intended for
use by persons (including
children) with reduced physical,
sensory or mental capabilities, or
lack of experience and
knowledge, unless they have
been given supervision or
instruction concerning use of the
product by a person responsible
for their safety. Children should
be supervised to ensure that they
do not play with the product.
・
Staff kitchen areas in shops, offices and other working environments;
・
Environments comparable to residential living rooms and kitchens;
※
This appliance is not intended for use by many unspecified
people for a long period of time.
Page 3
CV-TYQ_0405_E_20180314
4 5
仮
About 45
degrees
Push
Lid Lock
Indented Area of
the Lid Lock
Water Level Ball
REFILL Line
1
2
3
1
2
Upper Lid
Detach button
A rattling sound you may
hear when opening or
closing the Upper Lid or
when boiling is normal.
(see P.19)
This button must be pressed to
dispense hot water. (see pg.8)
Press this button again for Café
Drip Function.
(see pg.14)
CONTROL PANEL
To Open
To Close
To Detach
PARTS NAMES AND FUNCTIONS
How to Open/Close the Upper Lid
How to Detach/Attach the Upper Lid
Press the indented area of the
Lid Lock with your thumb.
Depress the Upper Lid until it
clicks shut.
Pull the Lid Lock up with your
fingers to open the Upper Lid.
Open the Upper Lid to about
a 45-degree angle.
Push the Upper Lid Detach
button.
Pull the Upper Lid forward
and up at an angle.
1
2
1
2
3
To Attach
Push the Upper Lid back into
place at the same angle.
Lid Lock
Steam Vent
●
Exercise care during the boiling
process as steam emitting from
the Steam Vent is very hot.
Inner Lid
●
If the Inner Lid Gasket hardens, changes
shape, turns white, or otherwise
becomes worn out, please replace it with
a new one. (Separate charge required.)
(see pg.16)
Not doing so may cause hot water to
leak when the product is tilted or tipped
over, resulting in scalding. Steam leaking
from the gap may also cause burns or
product failures.
Inner Lid Gasket
(Consumable Part)
Upper Lid
Press to dispense hot water. (see pg.8, 14)
Sets the Keep Warm temperature.
(see pg.10-11)
LCD display shows the water
temperature and Timer settings.
NOTE: Illustration is for reference only. Actual display will not
show all functions simultaneously during use.
QUICK TEMP light
BOIL light
TEMP SET
button
KEEP WARM light
Display
DISPENSE button
UNLOCK light
CAFÉ DRIP light
Power Cord
Cord
Swivel Base
Water Removal Area
Inner Container
Handle
Control Panel
●
Drain water here.
●
Appliance Plug
inserts here.
●
Do not let the Power Cord wrap
around the Main Body when turning.
●
Hot water dispenses from here.
●
For care and use instructions,
see pg.15.
Filter
Maximum Water
Level Line
Hinge
Receptacle
Water Level Gauge
Spout
●
Fill water above the line.
REFILL Line
Body
Twist Tie
●
Please remove the twist tie holding the
Power Cord before use.
●
Do not use the Power Cord bundled up.
Doing so may cause the Power Cord to
become excessively hot, resulting in
malfunction.
Appliance Plug
●
Press buttons down firmly.
●
The Sound Signals and raised dot ( ● ) in the center of the
DISPENSE button is provided for those with visual impairment.
Power Plug
REBOIL/
QUICK TEMP
button
UNLOCK button
Starts the Reboil
mode. (see pg.9)
Sets the Quick Temp
mode. (see pg.12)
Use to return to the original
temperature setting when
Energy-Saving mode is
selected. (see P.14)
Also used when performing the
Citric Acid Cleaning (to initiate
cleaning, press this button for more
than 3 seconds). (see pg.16)
ENERGY-SAVING/
TIMER button
Use when setting the
Energy-Saving mode or
Energy-Saving Timer function.
(see P.12-13)
●
The Water Level Ball is not
seen when the water level is
higher than the scale of
Water Level Gauge.
Water Level Ball
(Red Ball)
Page 4
CV-TYQ_0607_E_20180329
6 7
Beep
Turns on
Turns
off
Turns on
1
2
●
How to set the Keep Warm mode:
see P.10-11
●
How to set the Quick Temp mode:
see pg. 12
※
Approx. 37 minutes
Length of time until the water
temperature reaches about 90｡C:
Time required to boil water:
Maximum Water
Level Line
Close the Upper Lid
securely.
To ensure safe
operation while
boiling and to prevent
scalds if the product
is overturned.
Otherwise, may cause electric
shock, short circuit, smoke or
fire.
Be sure to insert the
Power Cord securely.
●
Do not allow the
end of the
Appliance Plug to
get soiled with dust
or come into contact
with metal objects
such as pins.
NOTE
When boiling has completed, a melody
sounds and it automatically switches
to 90｡C Keep Warm mode.
Includes approx. 4 minutes to
Dechlorinate.
(At a room temperature of 23｡C with the
Inner Container filled to the Maximum
Water Level Line with water temperature
at 23｡C.)
※
●
The length of time for the water
temperature to reach
90｡C
will vary
depending on the temperature of the
room and water.
(At a room temperature of 23｡C with the
Inner Container filled to the Maximum
Water Level Line.)
Approx. 1 hour and 10
minutes
When the water
temperature drops to about
90｡C
, "90" appears on the
Display.
98｡C
Keep Warm Mode. (see pg.10)
80｡C
Keep Warm Mode. (see pg.10)
70｡C
Keep Warm Mode. (see pg.11)
Vacuum Insulation (Non-Electric)
Keep Warm Mode. (see pg.11)
How to set the Keep Warm mode:
The BOIL light turns off, the KEEP WARM
light turns on and "100" appears on the
Display.
●
Add water when the water level is
low during the Keep Warm mode.
(The product automatically begins
heating the water.) If the water level
is still not high enough, it will not
automatically switch to Boil. In this
case, press the REBOIL/QUICK
TEMP button to manually start the
process. (see pg.9)
●
Please follow the instructions below
to prevent the risk of scalding:
・
Do not cover the Steam Vent with a
cloth.
・
Do not touch the Steam Vent or
bring your hands or face near the
Steam Vent.
・
Do not open the Upper Lid while
the BOIL light is on.
・
Do not dispense hot water while it
is boiling.
NOTE
2
Close the Upper Lid and connect the Power Cord.
1
BOIL MODE
Open the Upper Lid and fill
the Inner Container with water
using a pitcher or other ontainer.
●
Do not fill the
Inner Container
directly from a
water faucet or
place the product
on a wet surface
such as a sink. (Exposing
the heating element directly
to water may cause
malfunction.)
●
Avoid splashing water on
the Body or Control Panel.
(May cause malfunction.)
●
Before use,
check the Inner
Lid Gasket for
any deformation.
(May cause
steam leakage.)
NOTE
●
Do not fill over the Maximum
Water Level Line. (Hot water may
overflow from the Steam Vent.)
●
Do not fill the Inner Container with
hot water. (The Automatic
Shut-Off function may be
activated.) (see P.9)
●
Do not fill the Inner Container with
any liquid other than water.
●
Do not use water additives such
as charcoal for water purification
or mineral additives. (Small
particles may get clogged inside
of the product.)
●
If you wish to shorten the
completion time, add less water to
the Inner Container.
The first time
you use the product you
may notice the smell of
plastic. This is normal
and will gradually fade
away.
Fill the Inner Container with water to the Maximum Water
Level Line ( ), and boil water as directed. Once it
reaches a boil, press the UNLOCK button, then press the
DISPENSE button to dispense about 1 liter of hot water in
order to rinse the water route, and dispose the remaining
water. Fill with fresh water.
(Always remember to attach the Filter.)
●
When using mineral or Alkalized Ionic water:
When mineral or Alkalized Ionic water is used, a floating
residue may develop or a milky white substance may form
on the surface of the Inner Container. This is due to the
ingredients in the water and is harmless to your health.
Frequent cleaning is recommended.
●
At your initial use or when
using the product after a long period of storage:
How to change the Information Sound
from a melody to a beep. (see pg.14)
水量ボールの位置で水量が
ひと目で分かります。
Water Level Ball
To monitor the amount of water
you are filling, look at the Water
Level Ball position.
Water
Level
Gauge
Present Water
Level
The Water Level Ball is not
seen when the water level
is higher than the scale of
Water Level Gauge.
It automatically starts the boiling
process.
The BOIL light turns on and the
Display shows the water
temperature in 5｡C increments.
Page 5
CV-TYQ_0809_E_20180329
8
9
Short beep
Turns on
Beep
Turns on
Turns off
Turns on
Turns on
Short beep ×
10 times
Beeps will
sound, 3 lights
will turn on and
"HH" will appear
on the Display.
●
Be careful not to repeat
the boiling process
without filling the pot
with water, as the
Non-Stick Coating may
discolor and peel off.
The UNLOCK light turns on
and hot water can be
dispensed.
●
Do not unlock and press the
DISPENSE button if the Inner
Container is empty.
NOTE
2
Press the button to dispense hot water.
Do not swivel the product while dispensing water.
●
Initiallyupon boiling or if it has been a while after dispensing,the
water may not be very hot. Please discard the first cup (of the hot
water).
●
Do not attempt to dispense hot water while boiling.
●
Water may not dispense smoothly for a short period of time after
boiling.
●
Be careful as the Body heats up during the Boil and Keep Warm
modes.
1
Press the button.
DISPOSE WATER
Dispose leftover water when the product is not in use.
DISPENSE HOT WATER
A safety function to prevent hot water
from dispensing if the DISPENSE
button is accidentally pressed.
Automatic Dispense Lock
10 seconds after dispensing,
the UNLOCK light turns off
and the Automatic Dispense
Lock is activated.
Do not tilt or shake the
product after dispensing.
Hot water may drip from the
Spout, causing scalds.
●
Even if no water is dispensed, the
Automatic Dispense Lock will be
activated after about 10 seconds.
1
Unplug the Power Cord
and detach the Upper Lid.
●
Take precaution with the steam.
You may scald yourself.
When detaching the Upper Lid:
1
2
Spout
2
Hold the Handle securely.
Hold the product with both hands and dispose water where indicated
"EMPTY FROM HERE" on the wall of the Inner Container.
●
Take precaution with the
hot water and steam.
You may scald yourself.
●
Take precaution as hot
water may drip from the
Spout, causing scalds.
When disposing hot water:
Water Removal Area
●
Do not plug or unplug the
Power Plug or Appliance
Plug with wet hands. (Doing
so may cause short circuit
or electric shock.)
●
Do not dispose hot water
with the Upper Lid in place.
(The Upper Lid may come
off, spilling hot water and
causing scalds.)
●
Do not allow water to splash
on the Control Panel, Hinge,
Handle or Receptacle.
(Could cause scalding or
breakdown.)
●
Take precaution as not
attaching the Filter properly
may cause it to fall out
when dispensing hot water.
●
Dispose the water at least
once a day. (Leaving water
in the Inner Container can
cause unwanted odor or
scale build-up.)
NOTE
●
Make sure the water level is above the REFILL Line
before pressing the REBOIL/QUICK TEMP button.
Approx.
3〜4 minutes
Approx.
5〜8 minutes
98｡C Keep Warm Mode
90｡C Keep Warm Mode
The BOIL light turns on when
the boiling process begins.
(At a room temperature of 23｡C
with the Inner Container filled to
the Maximum Water Level Line.)
Time required to
finish reboiling
Reboil mode
Press the button.
This function is used when reboiling
water in the Keep Warm mode.
When the Reboil process is completed,
a melody sounds and the product
switches to Keep Warm mode.
NOTE
●
Pressing the REBOIL/QUICK TEMP button twice activates the
Quick Temp mode. (see pg.12)
●
Do not attempt to dispense hot water while reboiling.
●
Water may not dispense smoothly for a short period of time
after reboiling.
●
When the Energy-Saving mode is selected, you cannot
activate the Reboil mode. To start the Reboil mode, cancel the
Energy-Saving mode once, then press the REBOIL/QUICK
TEMP button. (see P.12)
Automatic Shut-Off function
Unplug the product. Allow the Inner Container
to cool. Fill the Inner Container with water and
plug back in.
●
When plugged in without filling the Inner Container with water.
●
When the water level is lower than the REFILL Line and boiling
has been attempted.
●
When the Inner Container is empty or the Upper Lid is left open for
adding water.
●
When pouring in hot water immediately after plugging in the unit.
The Automatic Shut-Off function activates to shut down power to the
heater in order to prevent damage from overheating. The Display will
show "HH" and beeps will sound to alert you that the Automatic Shut-Off
has been activated. The following conditions may cause activation:
Remedy
Page 6
CV-TYQ_1011_E_20180329
10 11
※
Turns on
Turns off
Blinks
Turns off
Turns off
2 short beeps
× 2 times
Turns on
2 short beeps
× 2 times
Turns on
●
If you wish to shorten
the time, add less water
to the Inner Container.
Fill water up to 1.0
on the Water Level
Gauge.
For example
HOW TO SET THE KEEP WARM MODE
Press the button to
change the settings.
Each press of the button changes the position
of the " " on the Display.
When the water
temperature reaches
98｡C, "98" appears on
the Display.
●
Depending on the altitude where the product
is used, the Keep Warm mode may be set at
96｡C-97｡C, in order to prevent continuous
boiling.
Select the "98" on the Display.
98｡C Keep Warm Mode
98｡C is ideal for making coffee, tea and
instant noodles.
For making coffee, tea and instant noodles
When the boiling process has completed, a
melody sounds, the BOIL light turns off and
the KEEP WARM light turns on.
■
Length of time for the water temperature to
reach 80｡C after boiling:
When the boiling process has completed, a
melody sounds, the BOIL light turns off, and
the KEEP WARM light begins to blink.
When the water
temperature reaches
about 80｡C, "80"
appears on the Display,
and the KEEP WARM
light stops blinking and
remains on.
If initiated during Keep Warm mode, the light
will blink 2 seconds after the selection.
●
The length of time for the water temperature
to reach 80｡C will vary depending on the
room temperature and amount of water.
(At a room temperature of 23｡C with the Inner Container
filled to the Maximum Water Level Line.)
When the boiling
process has
completed, a melody
sounds, the BOIL
light turns off, and
the KEEP WARM
light begins to blink.
If initiated during
Keep Warm mode,
the light will blink 2
seconds after the
selection.
Select the "80" on the Display.
80｡C Keep Warm Mode
80｡C is ideal for making Japanese (green)
tea.
Select the "70" on the Display.
70˚C Keep Warm Mode
70˚C is ideal for preparing baby formula.
For preparing baby formula
When the water
temperature reaches
about 70˚C, "70"
appears on the Display
and the KEEP WARM
light stops blinking and
remains on.
For making Japanese (green) tea
■
Length of time for the water temperature to
reach 70˚C after boiling:
●
The length of time for the water temperature
to reach 70˚C will vary depending on the
room temperature and amount of water.
(At a room temperature of 23˚C.)
・Be sure to check that the KEEP WARM light is on
and NOT blinking before dispensing.
・Do not use the Quick Temp mode. (see pg.12)
70˚C is ideal for preparing formula. Dissolve the
formula and let cool to optimum temperature
(slightly higher than body temperature). If fed
without cooling, babies are at risk of scalding.
Approx. 3 hours and 30 minutes
When preparing baby formula:
When water is boiled in the Quick Temp mode,
the KEEP WARM light does not blink but turns
on. (see pg.12)
1.0 L
4.0 L
Approx. 2 hours
Approx. 5 hours and 40 minutes
■
Water temperature during VACUUM
INSULATION Keep Warm Mode:
(Temperatures are measured in the center of the Inner Container and are
based on a room temperature of 23｡C, with the maximum amount of water.)
●
Temperature is measured in the center of the
Inner Container. The water temperature in the
upper and lower area will differ as time pass, and
the temperature in the center is measured as the
average.
●
As the water temperature drops, the display
temperature may be lower than actual when the
Vacuum Insulation Keep Warm mode is selected.
●
The lower the amount of water, the faster the
temperature will drop.
●
During the Vacuum Insulation Keep Warm mode,
the product will not automatically start reboiling.
To resume boiling, manually press the
REBOIL/QUICK TEMP button.
Select "VACUUM" on the Display.
This mode saves electricity by shutting off the
power to the heater after the boiling process is
completed and keeps it warm by Vacuum insulation.
When the boiling process has completed, a
melody sounds, and the BOIL light turns off.
For saving electricity
Vacuum Insulation Keep
Warm Mode
Approx. 85｡C
Approx. 78｡C
2 hours later
Approx. 92｡C
4 hours later
6 hours later
After complete boiling
90 98 90 80 70
VACUUM
●
You cannot select the 98°C Keep
Warm mode and Vacuum Insulation
Keep Warm mode while the Quick
Temp mode is selected.
※
You will hear 2 short beeps when 90｡C
Keep Warm mode is selected.
(Default)
Beep
●
You can change the temperature
setting during Keep Warm mode.
It may start reboiling depending on
the water temperature and the
selected setting.
●
Re-insert the Power Plug when the plug is detached by
accident.
●
If the plug is detached for more than a few minutes and be
inserted, the pot returns to the Energy-Saving 90｡C Keep
Warm mode and it may start reboiling automatically.
If the Power Plug is detached while the Thermal
Insulation Keep Warm mode is selected:
Page 7
CV-TYQ_1213_E_20180322
※
Turns off
Beep
Turns off
Turns on
Turns on
You cannot activate Quick
Temp mode while the
product is set at 98°C
Keep Warm mode or
Vacuum Insulation Keep
Warm mode.
Beep
Turns on
Beep
※You will hear 2 beeps
when 6H is selected.
Beep
13
12
●
Water does not reach a boil under Quick Temp mode, and
should not be used to prepare baby formula.
●
Although the water will not reach a boil when Quick
Temp mode is activated, the Steam Vent will become
hot. Please do not touch it.
※
After reaching the
selected temperature,
it will automatically
switch to Keep Warm.
(The QUICK TEMP light
turns off and the KEEP
WARM light turns on.)
●
You cannot select 98°C Keep Warm mode or Vacuum
Insulation Keep Warm mode while Quick Temp mode is
activated.
●
There may be a lingering chlorine smell if tap water is used while
Quick Temp mode is activated. If this is an issue, use the regular
Boil mode instead.
●
Depending on the amount of water and room temperature the
actual water temperature after heating may differ from that
shown on the Display.
●
Depending on the amount of water, room temperature, and
atmospheric pressure, some steam may be produced.
●
The Quick Temp mode may be canceled if the Power Cord is
detached. Set to the desired mode again.
●
The product begins the Regular Boil mode when water is added.
Activate the Quick Temp mode again.
Each press of the Energy-Save/Timer button changes the mode and set time.
When operation is not confirmed for approx. 2 seconds, the displayed settings is activated.
A melody sounds and the Energy-Saving
Timer function is activated.
The Boiling function will complete at the set time.
●
When using the Energy-Saving Timer function with the
Quick Temp mode, set the Quick Temp mode after
selecting the Energy-Saving Timer function
Boiling may stop earlier than set, depending on room
temperature, water temperature and amount of water.
The BOIL light turns off and the KEEP WARM light turns on.
How to cancel
Energy-Saving Timer
function
Or
Press the button once.
●
It is unable to use the Energy-Saving
mode with Energy-Saving Timer function.
While the water is heating, press the
button to select the Quick Temp mode.
※
At the 70°C Keep Warm mode only, water is heated once to approx. 80°C and
then kept warm at approx. 70°C. The length of time for the water temperature to
reach approx. 70°C. 1 hour after boiling. (At a room temperature of 23°C with
the Inner Container filled to the Maximum Water Level Line.)
This function heats the water to the Keep Warm temperature
setting without reaching a boil. The water will reach the Keep
Warm temperature setting quicker.
As compared to the regular Boil mode, the function shortens the
boiling time, suppresses steam generation, and helps save
energy.
The Quick Temp mode is unable to boil and dechlorinate water.
Set this mode for potable water.
Each press of the REBOIL/QUICK TEMP button changes the boil mode.
Regular Boil mode Quick Temp mode
(Default)
NOTE
In the case of 98°C Keep Warm mode, 90°C Keep Warm mode,
and 80°C Keep Warm mode
6H 7H 8H 9H 10H
Cancel (temperature display)
Energy-Saving
mode
Energy-Saving
mode
Energy-Saving Timer function
Energy-Saving Timer function
6H 7H 8H 9H 10H
Energy-Saving Timer functionEnergy-Saving Timer function
Cancel (temperature display)
In the case of 70°C Keep Warm mode and
Vacuum Insulation Keep Warm mode
You cannot select the
Energy-Saving mode
while 70°C Keep Wa rm
mode or Vacuum
Insulation Keep Warm
mode is activated.
Press the button, and set
either Energy-Saving mode or
Energy-Saving Timer function
(6 hours to 10 hours).
When the Energy-Saving mode is fixed,
the temperature display turns on.
Energy-Saving
Mode
For approx. 2 seconds after selecting the Energy-Saving
mode, the temperature display turns off.
The following cases, too, cancel the Energy-Saving mode.
●
Water may not be dispensed smoothly for a while
after heating to the Keep-Warm temperature
setting. The temperature shown on the Display
after heating may differ from the Keep-Warm
temperature setting.
●
The product automatically begins heating the
water by adding water. If the water level is still not
high enough, it will not automatically switch to Boil.
In this case, cancel the Energy-Saving mode, then
press the REBOIL /QUICK TEMP button.
●
When 70°C Keep Warm mode or Vacuum
Insulation Keep Warm mode is chosen in the
Energy-Saving mode.
How to cancel
the Energy-Saving
mode
Further,
Press the button
once.
Press the button.
Energy-Saving while waiting
When water is he ated to the original
temperature setting
Energy-Saving starts.
After automatically shutting off electricity to the heater,
water is kept warm at approx. 70°C.
●
When the water temperature is lower than the
temperature setting, the BOIL light turns on and water is
heated to the temperature setting. After completing
boiling, the hot water may become higher than the
temperature setting.
●
When the water temperature is higher than the
temperature setting, water is not boiled when the
REBOIL /QUICK TEMP button is pressed.
●
The REBOIL /QUICK TEMP button is re jected in Energy-Saving
standby mode.
The setting returns to the Energy-Saving
standby mode.
After water is heated to the temperature setting, the
setting returns to the Energy-Saving standby state.
Energy-Saving
standby mode
When operation is not confirmed for approx. 2 hours,
the Energy-Saving mode helps save energy by
automatically shutting off electricity to the heater and
keeping water warm at approx. 70°C.
The Boiling function will complete after the set time.
(The Energy-Saving Timer function helps save energy by
shutting off electricity to the heater until boiling begins.)
When operation is not confirmed
for continuously approx. 2 hours
When the
Energy-Saving Timer
function is re-selected
Press the button
several times to set the
timer to the desired time.
（6H〜10H）
Energy-Saving Timer
Function
Press the button
several times.
If the Power Cord is detached, the Energy-Save
Mode/Energy-Save Timer function will be cancelled and
must be reset.
If the Power Cord is detached:
QUICK TEMP MODE
ENERGY-SAVING MODE
/ ENERGY-SAVING TIMER FUNCTION
At the 70℃ Keep Warm mode, after the KEEP WARM light blinks,
two short beeps will sound and the KEEP WARM light will turn on.
Page 8
CV-TYQ_1415_E_20180314
1514
Hole on the
Inner Lid
Always unplug the Power Cord,
dispose all water, and allow to cool
completely before cleaning.
The Inner Lid Gasket may need to be replaced due to time and
wear. We recommend that you replace it about once a year.
HOW TO REPLACE THE INNER LID GASKET
●
Do not attempt to dry the product by turning it upside down when the bottom is wet. (Water may get inside
the body and cause it to break or rust.)
●
Do not use the following:
・
Thinner, benzene and bleach. (Doing so may cause discoloration, crack, degradation and corrosion.)
・
Polishing powder, nylon brushes, anything made with metal, eraser pads, hard nylon sponges and abrasive cleaners. (Doing so
may cause corrosion.)
・
Detergent. (Hot water may spill out, resulting in scalds or damage. Doing so may cause unwanted odor.)
●
Do not use scrub brushes for any portions other than the Filter. (Doing so may cause corrosion.)
●
When using chemically treated cloths, do not rub too hard or leave them on the product for a long time as the surfaces of the
product may be damaged by chemical reactions.
●
Do not use a dishwasher or dish dryer for cleaning or drying. (Doing so may cause the plastic parts to deform.)
●
Before storing the product for a longer period of time, dry it completely and pack in a plastic bag to prevent odors from being absorbed.
Body/Upper Lid
CLEANING AND MAINTENANCE
Wipe clean with a
damp well-wrung cloth.
●
Do not wash any part of the Body, Control
Panel or Water Level Gauge with water.
(May cause malfunction or rust.)
Wipe new Inner Lid Gaskets with a wet soft sponge before attaching to the Inner Lid.
To remove the Inner Lid Gasket
To attach the Inner Lid Gasket
NOTE
①
Remove the three screws, and remove the Inner Lid.
②
Remove the Inner Lid Gasket which is installed on the
Inner Lid.
After removing the Inner Lid, check the plastic part of
the Upper Lid for abnormalities.
→If this part is discolored or if it feels rough to the touch,
replace it (there will be a fee for this).
①
Fit the Inner Lid Gasket securely to the outer
circumference as shown in the figure.
②
Place them correctly onto the Upper Lid and tighten the
screws securely.
●
Do not lose these screws.
If the Inner Lid Gasket hardens, changes shape, turns white, or otherwise
becomes worn out, hot water may leak from the gap between the Upper Lid
and Body when tilted. Steam may also leak from the gap, causing burns and
product failures, which may result in scalds. If hot water spews from the
gap or there is steam even after replacing the Inner Lid Gasket, other parts
may be in need of repair. Please contact the store where you purchased the
product.
When the Inner Lid Gasket
hardens, changes shape,
turns white, or otherwise
becomes worn out.
Please purchase
and replace with
a new one.
Wipe with a soft wet sponge.
Inner Lid
Wipe clean with a dry cloth.
Power Cord
Filter
Remove the Filter from the Inner
Container and wash with a soft brush.
Pull the Filter up to release, and press
down firmly to attach.
If you find it difficult to clean the Filter, replace
it with a new one. (see pg.17)
●
Never use the product without installing the Filter.
(The Filter prevents foreign objects from entering the water
route or Electric Pump and obstructing the flow of hot water.)
●
Red rust spots (Rust Stain)is visible on the Inner Container.
●
Milky white or gray discoloration and/or filmy objects
are found in the water.
●
Boiling is louder than usual.
●
Hot water has an odor.
(The condition of the Inner Container will vary
depending on the water quality and frequency of use.)
Especially when...
Perform the Citric Acid Cleaning
(see pg.16) periodically.
Inner Container
Inner Lid
Gasket
Inner Lid
Screws (x3)
Inner Lid Gasket
Inner Lid
Upper Lid
CAFÉ DRIP FUNCTION
1
When the CAFÉ DRIP light
turns on, Café Drip Function is
activated.
This function decreases the amount of water dispensed to 60% of the normal setting, making it suitable
for brewing café drip coffee.
Press the button
twice.
●
Be careful not to burn yourself.
●
If using a cone filter placed directly on a
cup, be careful not to let it fall inside the
cup while brewing.
●
When using a manual drip coffee cone,
dispense a cup of hot water before
brewing. (The first cup may not be hot
enough.)
●
Pressing the UNLOCK button again during
Café Drip
Function
will reset the product to
the normal dispensing mode.
●
When the light turns off, the Automatic
Dispense Lock will be activated.
●
If the water level is low, it may take longer
for water to begin dispensing after pressing
the DISPENSE button.
●
If the water level is low or boiling has just
completed, water may not dispense
smoothly.
NOTE
2
You can use the Café Drip
Function for about 60 seconds
while the CAFÉ DRIP light is
on.
Press the
button to dispense
hot water.
Turns on
Long beep
1
●
Each button press changes the
Information Sound.
Press the button for more
than 3 seconds during the boiling
process or Keep Warm mode.
2
Once your desired sound
(melody or beep) is heard,
the setting is completed.
The product informs you with a melody or beeps that it has finished
boiling or the timer has been set.
HOW TO CHANGE THE INFORMATION SOUND
●
Information Sound:
When
Type
Minuet
Beautiful Dreamer
×
×
×
5 long beeps
Boiling stops
Timer is set
When and what types of
Information Sounds are heard:
Press for more
than 3 seconds
Press for more
than 3 seconds
Melody
Silent
Melody Beeping Silent
Press for more
than 3 seconds
Beeping
(Default)
3 long beeps
Long beep
(Melody)
●
If the Silent setting is selected, a beep will
indicate the setting has completed.
●
The Information Sound will return to
Melody if the product is unplugged.
Page 9
CV-TYQ_1617_E_20180329
16 17
4
●
If mineral or Alkalized Ionic water is
used, calcium tends to build up on
the surface of the Inner Container. If
scale accumulates on the Inner
Container or the Filter, boiling may
become louder than usual and water
may not dispense smoothly.
Frequent cleaning is recommended
when using mineral or Alkalized Ionic
water.
To cancel the Citric Acid Cleaning at any time,
unplug the Power Plug for more than 5 seconds.
●
Repeated citric acid cleaning may
be necessary for hard-to-remove
residues or if water does not
dispense smoothly.
NOTE
●
Take precaution with the hot water
and steam. You may scald yourself.
●
Take precaution as hot water may
drip from the Spout, causing scalds.
When disposing hot water:
3
P.16
P.2
P.8
P.7
P.9
Is it okay to use the product for
heating liquids other than water?
Do not fill the product with any liquid other than water. It may cause
malfunction, or may overflow and cause scalding.
Is it okay to use mineral
water or Alkalized Ionic
water?
Yes. However, when mineral or Alkalized Ionic water is used, a floating
residue may develop or milky white substance may form on the surface of the
Inner Container. This is due to the ingredients in the water and is harmless to
your health. Frequent cleaning is recommended.
I accidentally drank water while
performing the Citric Acid Cleaning.
Is this harmful to my health?
Please follow the instructions shown on the package of the citric acid
cleaner CD-K03E-JU.
Is it okay to go out while
the product is turned on?
It is safe to use the product unattended as it has an Automatic Shut-Off function (power
to the heater will be automatically turned off), which will be activated once it is empty of
water. However be careful not to repeat the boiling process without filling the Inner
Container with water, as the Nonstick Coating may discolor and peel.
Does the water need to be
changed every day?
To prevent scale from building up, please change the water at least once a
day.
Check that the Filter is attached
to the Inner Container.
Preparation:
●
If the Filter is dirty, remove
it from the Inner Container,
wash with a soft brush and
reinstall.
NOTE
2
Beeps when the cleaning process is completed.
Turns on
5 long beeps
※Cleaning times may vary
depending on the amount
of water, water
temperature and room
temperature.
Approx. 1.5 hours.
Cleaning time:
1
Beep
Beeps when the cleaning process begins.
In order to prevent gas bubbles and bubbling-over, the Citric Acid Cleaner for
Electric Water Boilers (CD-K03E-JU) is recommended for cleaning. To
purchase this cleaner, please visit an authorized Zojirushi dealer.
NOTE
Blinks
2 lights will
blink.
LCD display will
show a square as
illustrated.
The square
shown on the
Display rotates.
2 lights will stop
blinking and stay
on.
Unplug the Power Plug, detach the
Upper Lid and dispose water where
indicated "EMPTY FROM HERE."
(Please take precautions not to splash water
on the Hinge.)
To rinse, fill the Inner Container with
water. Boil and dispense about a cup of
hot water to rinse out the Spout, allow to
cool, then dispose the remaining water.
Q&A ON PRODUCT USE
Please check the following
points before calling for service.
TROUBLESHOOTING GUIDE
Condition Cause Remedy
The product has not been used for a long
time.
Hot water has a
disagreeable odor.
●
A mild plastic odor may be
noticeable with a new product.
This odor will gradually fade
away.
●
You may smell chlorine (used
for sterilization of tap water)
after boiling.
Boil water, unlock and dispense
about 1 liter of hot water. Discard
the remaining. (see pg.7)
If this is an issue, use the regular Boil
mode instead. (see pg.12)
The regular Boil mode purges chlorine
in tap water by boiling completion.
Scale or other residue has accumulated
on the Inner Container.
You have not performed citric acid
cleaning regularly.
Perform citric acid cleaning.
(see pg.16)
If tap water is used under Quick Temp
Function, it will take an additional 15
minutes after heating completes at the set
temperature removing up to 80% of the
chlorine.
Do not drink
the water used
for citric acid
cleaning.
HOW TO PERFORM CITRIC ACID CLEANING
Put 1 package of the Citric Acid Cleaner
CD-K03E-JU in a cup and add warm water to
dissolve. Pour it into the Inner Container and
fill with water to the Maximum Water Level Line.
●
Do not fill over the
Maximum Water Level
Line. (Hot water may spill
out, resulting in scalds.)
NOTE
Close the Upper Lid, insert the Power Plug and press the button for
more than 3 seconds.
625702-00
BF297053G-00
CD-K03E-JU
REPLACEMENT PARTS
●
Replacement parts may be available for an
additional charge. Please replace damaged parts
only with new parts.
●
When replacing parts, please record the model
number and part name beforehand. Then contact
the retail store where you purchased this product.
Parts Names Parts Number
Citric Acid Cleaner for Electric
Water Boilers (30g×4 packets)
Inner Lid Gasket
Filter
Perform every 1-3 month(s) of usage
Water does not heat up.
Connect the Power Plug.
Power Plug is not connected to an
electrical outlet.
Page 10
CV-TYQ_1819_E_20180322
1918
TROUBLESHOOTING GUIDE (cont.)
Water pours out by itself from
the Spout or Steam Vent.
Pour out the excess water until it is
below the Maximum Water Level Line.
Check that the Inner Container is not filled
over the Maximum Water Level Line.
Use the Quick Temp mode for other
than 98°C Keep Warm mode or
Vacuum Insulation Keep Warm
mode. (see P.12)
The 98°C Keep Warm mode or
Vacuum Insulation Keep Warm
mode cannot be selected during
the Quick Temp mode.
Steam is produced from the pot
at the Quick Temp mode.
●
The Quick Temp mode prevents the water in the pot from boiling. However, steam
may be produced, depending on the room temperature, amount of water, and
atmospheric pressure.
You cannot select the 98°C Keep Warm
mode and Vacuum Insulation Keep
Warm modeduring the Quick Temp
mode.
The Quick Temp mode cannot
be selected.
Select the 90, 80 or 70°C Keep
Warm mode, then select the Quick
Temp mode. (see P.12)
Is the 98°C Keep Warm mode or
Vacuum Insulation Keep Warm mode
selected?
The amount of water kept warm is too
low.
Add water (below the Maximum
Water Level Line) and press the
REBOIL/QUICK TEMP button.
Water cools easily during
Vacuum Insulation Keep
Warm mode.
Bubbles form from the bottom of the
Inner Container while water is being
heated. Dispense hot water after the
bubbling stops.
Clean the Inner Container and Filter.
(see P.15)
Press the UNLOCK button, then press
the DISPENSE button. (see P.8)
Water does not dispense or
does not pour properly.
Hot water does not pour properly a few
minutes after boiling.
Scale or other residue has accumulated
on the Inner Container and Filter.
The Automatic Dispense Lock is
activated.
Scale may build up in the water route or
Electric Pump and prevent water from
dispensing smoothly.
Power Plug is not connected to an electrical
outlet.
Connect the Power Plug.
A filmy, floating residue is
noticeable. (Could the Nonstick
Coating be peeling off?)
Residue is due to the mineral content in
water, not from corrosion of the Inner
Container or peeling of the Nonstick Coating.
Milky white and rough-surfaced
objects have built up on the
surface of the Inner Container.
Boiling is louder than usual.
Excessive accumulation of scale and
other build-up on the surface of the Inner
Container can cause boiling to become
louder.
Red rust-like spotting appears
on the surface of the Inner
Container.
Caused by iron in the water, not
deterioration of the Inner Container.
Perform citric acid cleaning.
(see P.16)
Over time and use, calcium
and other minerals
contained in water build up
on the surface of the Inner
Container and the Filter. It is
called "scale" and is
harmless to your health.
Scale
If this part is discolored or if it feels
rough to the touch, replace it.
A white floating residue is
noticeable.
Remove the Inner Lid and check the
plastic part of the Upper Lid for
abnormalities. (see P.15)
Condition Cause Remedy
Condition Cause Remedy
The Quick Temp mode is selected.
(Water does not reach a boil under
Quick Temp mode.)
Press the REBOIL/QUICK TEMP
button, select the regular Boil mode.
(see P.12)
Water does not boil.
Water is not hot.
Initiallyupon boiling or if it has been a
while after dispensing,the water may not
be very hot due to water remaining in the
Water Level Gauge.
Please discard the first cup (of the
hot water).
Is the Energy-Saving mode or Timer set?
Press the REBOIL/QUICK TEMP
button. (see P.11, 14-15)
Is the Vacuum Insulation Keep Warm
mode selected? If yes, then power to
the heater has been turned off, causing
the water temperature to gradually drop.
●
If water is filled from a faucet or the product is placed directly on a sink and the bottom
becomes wet, water may go inside of the Body and the Display may show moisture.
This may cause short-circuiting or electric shocks, unplug the Power Cord and contact
our authorized service center.
You pressed the
REBOIL/QUICK TEMP
button for 3 seconds or more.
The Inner Container is in a
citric acid cleaning cycle.
The Body becomes hot.
●
When the water temperature and/or room temperature is high, the outer surface of
the Body may reach up to 60˚C. This is not a malfunction.
You hear a rattling sound when
opening and closing the Upper Lid
or when boiling.
●
This sound is normal and comes from the movement of the weight which prevents hot
water from flowing out when the product is overturned.
The Power Cord becomes hot.
●
The Power Cord may become hot while the water is boiling. This is not a malfunction.
Humidity builds in the Display
window.
Error Displays and their meaning
Replacement for
the Upper Lid
A beep sounds,
3 lights turn on and
"HH" appears on
the Display.
2 lights blink at the
same time and the
Display shows a
rotating square.
The Inner Container is low
on water or hot water was
added to the Inner
Container, causing the
Automatic Shut-Off function
to engage.
Unplug the Power Plug and
wait until the Inner Container
cools down. Add water and
plug in the Power Cord.
(see P.9)
To cancel the citric acid
cleaning cycle, unplug the
Power Plug and wait more
than 5 seconds before
plugging back in. (see P.16)
, or
is displayed.
Indicates malfunction.
Please contact the retail store where
you purchased this product.
●
The Inner Lid Gasket is replaceable, and we recommend that you replace it about
once a year. If steam leaks from the gap between the Upper Lid and the Body, or if
the Inner Lid Gasket hardens, changes shape, turns white, or otherwise becomes
worn out, please replace it. (see P.15)
Inner Lid Gasket
●
The plastic part of the Upper Lid may deteriorate over use. When replacing the Inner
Lid Gasket, check the plastic part. If discoloration occurs or the surface becomes
coarse, replace the Upper Lid (must purchase separately). (We take care in only
using materials for the plastic parts that are safe and hygienic for food contact.)
Plastic Parts
The Nonstick Coating of the Inner Container may become damaged over use.
Contact the retail store where you purchased this product.
Blinks
Turns on
Loading...