Page 1
Smart Business Security System
Quick Start Guide
1
Getting to know your Business Security
System
The Zmodo Business Security System provides a full-featured monitoring
solution to cover your entire business space. The business system includes an
NVR for local storage, HD cameras with cloud storage options, and sPoE
Repeaters to connect the cameras. The sPoE repeater allows you to run one
cable from your router to power on multiple cameras in each zone of your
business. It will also allow for longer cable runs from your NVR.
Network Requirements:
720p cameras: Requires at least 1mbps upload when live viewing or 2mbps
upload when using the Cloud Service for each camera.
1080p cameras: Requires at least 2mbps upload when live viewing or 4mbps
upload when using the Cloud Service for each camera.
In order to optimize bandwidth and the number of ports on your WiFi router,
you may use a network switch, however your sPoE Repeater(s) and NVR must
be connected to the same network.
2
Hard Drive Disk Installation
If your system does not include a pre-installed hard drive (HDD), you can
purchase your own and follow the steps below for installation. Make sure
that you purchase a 3.5" HDD optimized for always-on read/write
surveillance, e.g. low-powered WD10PURX HDD.
1
Make sure that your NVR is powered off and unplugged from the power
source. Using a screwdriver, remove the four screws located on the
bottom panel as shown below.
1
Page 2
2
Slide your HDD until the SATA ports on the NVR and the corresponding ports
on the HDD are properly connected, and the HDD is secure.
3
Replace the cover, and fasten the screws into the corresponding holes using
a screwdriver.
4
Peel the cover from the four rubber pads
(provided) to expose the adhesive backing.
Press firmly onto the bottom panel to cover
the four screws.
NVR Status Indicator
NVR Status Indicator will let you know the
status of your NVR. Please refer to the chart
for specific details.
Solid green
The NVR is powered on and no IP cameras have been detected.
Solid blue
IP cameras and a hard drive have been detected by the NVR.
Blinking blue
The NVR is recording video to the hard drive.
Solid red
There is no hard drive, or there is a malfunction with your hard drive.
Blinking red
Your NVR may have encountered an error. Try restarting the NVR. If the
problem still persists, please contact Zmodo Support.
2
Page 3
3
Connecting your system
Power Supply
sPoE Repeater
Camera
Dis play
NVR
HDMI
Wireless Router
Connection Diagram
1
Find a suitable location for your NVR and sPoE Repeater(s) and plug them into
nearby power outlets.
2
Connect the NVR and the sPoE Repeater to an open ethernet port on your
WiFi router or network switch (not included). The sPoE Repeater(s) and NVR
must be connected to the same network. You may use the provided ethernet
cables.
3
Connect the wired cameras to the ports on the sPoE Repeater using the
provided simplified Power over Ethernet (sPoE) cables. This cable will provide
both video and power to your cameras. Please connect all cameras and
make sure that they work before performing permanent installation.
4
(Optional) You can connect an external monitor to view your NVR locally. Use
the HDMI port (cable not included) to connect your NVR to a local display, and
connect a USB mouse to control it.
Note: There will be no password when you first use your NVR locally. However, we strongly
recommend that you set a password after you configure your NVR. Set a password by going
to the Main Menu > General Settings > Account Settings.
Safety Requirements
Place your NVR and sPoE Repeater in a well-ventilated area.
Do not place any objects on top of your NVR or sPoE Repeater.
Try to keep your NVR and sPoE Repeater in a cool operating temperature.
Do NOT move or shake the NVR while operating, or else the hard drive will be
damaged.
Use a surge protector to protect the NVR and the sPoE Repeater from shortages.
Use only the provided power adapters with your products.
If water or any liquid comes into contact with the NVR and the sPoE Repeater,
unplug it immediately and contact Zmodo support.
3
Page 4
4
Configuring your system
Local Viewing
If you are accessing your system locally, please make sure that you have
properly connected your system (Part 3), and power on your NVR and the
sPoE Repeater. Once you have logged into your NVR interface, please wait
3-5 minutes for your system to automatically add the cameras.
Remote Viewing
You can access your system from any location with a working internet
connection. In order to set up remote viewing, you will need a mobile device
with Android or iOS . Follow the steps below to configure your system for
remote viewing:
1
Connect your mobile device to the same WiFi network that your NVR is
connected to.
2
Download and install the “Zmodo” app from Google Play or the App
Store (compatibility: 9.0+ or Android 4.0+). Launch the app and
sign up for a free Zmodo account. All of your devices will be bound to this
account.
3
Log into your Zmodo account within 15 minutes of powering on your NVR
and sPoE Repeater(s). The NVR and cameras will be automatically added
onto your account. If not, tap the [+] Add Device icon on the upper right
corner of the Home Screen. Select the “Wireless Device and Smart Kit”
connection method and then select the “Smart Kit” option. The app will
automatically search for NVRs that are connected to the same network as
your mobile device. Add your NVR and press “Finish” when prompted. You
will not need to configure any cameras.
TM ®
TM TM
Zmodo
TM
4
Page 5
4
In addition to viewing your system locally on your monitor and remotely
on your mobile device, you can also access your system from any
location with our web app. Just type into your web user.zmodo.com
browser and log in using your Zmodo account information.
5
Mounting your cameras
The following is an example of a potential installation map. You may refer
to the diagram below as a general guideline for your installation.
Res troom
Off ice 2
Gar age
Off ice 1
Off ice 3
WiF i Ro uter
sPo E Re peater
NVR
Cameras
5
Page 6
If you’re installing your cameras outdoors, all wired connections must be
weatherproof.
Before you perform any permanent installation and route wires, plug in your
cameras to the sPoE Repeater using the provided cables to make sure no
components were damaged during shipping.
Before installing the cameras, carefully plan where and how they will be
positioned, and how you will route the wiring that connects your cameras to
the sPoE Repeater.
Before mounting, make sure you have drilled the appropriate holes to run
the sPoE cables from the sPoE Repeater to your camera.
1
Line the camera bracket against the wall where you would like to install the
cameras, and mark the appropriate holes. Remove the bracket, and drill
three holes slightly smaller than the wall anchors. Use a hammer to
gently insert the anchors into the wall. Fasten the three screws through the
holes on the bracket and into the anchors as shown. Plug in your camera to
the sPoE Repeater using the routed cable.
6
Page 7
2
You will be able to adjust the camera position using the adjustable camera
bracket. Position the camera for an optimal viewing angle, and tighten the
bracket.
6
Troubleshooting
The NVR doesn’t recognize the correct cameras.
Your NVR may be recognizing other cameras on your network. Please
manually delete all cameras by going to the “Add Device” menu from your
NVR’s interface. Select the “Search and Add All Devices Automatically”
option, and wait 3-5 minutes for the NVR to add the camera. If this fails, you
can also disable the automatic search and add your camera manually.
I can't access the NVR remotely.
Please make sure your internet is working, and check that your NVR and the
sPoE Repeater are properly connected to the router.
The app doesn’t find my NVR during setup.
Make sure that your NVR and the sPoE Repeater are properly connected and
powered on, and reconnect your phone to your WiFi network. You may need
to exit the setup and try again.
7
Page 8
7
Support
Having difficulty?
You can use the Live Chat function in Zmodo app if you have any technical
problems.
Please follow the steps below:
Access the “Me” page in the lower right corner in Zmodo app and select
"Zmodo Support".
For more instructions, troubleshooting, support, and other resources,
please visit:
Androi d is a trademark o f Google Inc. Go ogle Play is a tra demark of Goog le Inc.
Apple , the App le Logo , and iPhone are tr ademarks of Ap ple Inc., regi stered i n the
U.S. an d other c ountr ies. App Store is a s ervice mark of A pple Inc.
www. zm od o. co m/ su pp or t
Like us on Facebook.com/Zmodo
Scan the QR-code below!
Follow us on Twitt er @Z mo do
Scan the QR -c od e below!
8
REV-A07
Loading...