ZLINE DW304H24, DW30424, DW771324, DW771418, DWSSH18 Installation Manual

1

CONTENTS

Installation Guide

SAFETY INSTRUCTIONS 2

Important Safety Instructions

Grounding Instructions

BEFORE INSTALLING 4

Electric Shock Hazard

PREPARING THE DISHWASHER ENCLOSURE 5

Product Dimensions

Enclosure Dimensions

INSTALLING THE DISHWASHER 6

Step 1: Check the Parts and Tools

Step 2: Select the Best Location for the Dishwasher

Step 3: Check Water Supply Requirements and Cautions

Step 4: Check the Electrical Requirements and Cautions

Step 5: Unpacking and Inspecting the Dishwasher

Step 6: Preparing the Dishwasher

Step 7: Placing the Dishwasher and Connecting the Hot Water Supply Line

Step 8: Leveling the Dishwasher

Step 9: Securing the Dishwasher

Step 10: Connecting the Drain Hose

Step 11: Wiring Connections

Step 12: Completing the Installation

SPECIFICATIONS 24

CONTENTS

Users Manual

SAFETY INSTRUCTIONS 26

Proper Installation

Basic Precaution Before Use

FEATURES OF YOUR NEW DISHWASHER 28

Specification

Filter System

Smart Wash System

OPERATING INSTRUCTIONS 32

Control Panel

Cycle Chart

PREPARING AND LOADING DISHES 36

Loading the Lower Basket

Loading the Upper Basket

Loading the Silverware Basket

Adding a Dish

Filling the Detergent Dispenser

Filling the Rinse Aid Reservoir

USER MAINTENANCE 40

Cleaning the Exterior

Cleaning the Interior

Cleaning the Nozzles

TROUBLESHOOTING 41

Installation Guide

SAFETY INSTRUCTIONS

Throughout this manual, you’ll see Warning and Caution notes. These warnings,

cautions, and important safety instructions that follow do not cover all possible

conditions and situations that may occur. It’s your responsibility to use common

sense, caution, and care when installing, maintaining, and operating the dishwasher.

Zline is not liable for damages resulting from improper use.

These warning signs are here to prevent injury to you and others. Please follow

them explicitly. After reading this book, keep it in a safe place for future reference.

Important Safety Instructions

Hazards or unsafe practices that may result in severe personal injury or

WARNING

Hazards or unsafe practices that may result in personal injury or property
damage.

death.

CAUTION

To reduce risk of fire, explosion, electric shock, or personal injury when
using the dishwasher, follow these basic safety precautions.

CAUTION

Make sure the machine is grounded to prevent electric shock.

Read all instructions before using the appliance.

Install and store the dishwasher inside, away from exposure to weather.

Do not install the dishwasher near electrical components. Keep the

CAUTION

dishwasher away from open flames.

Do not install the dishwasher on a carpet as this is a fire hazard.

Do not install the dishwasher in a location where the water may freeze (where the

temperature falls below 32°F(0°C). Frozen water in the hoses or pipes may damage

the dishwasher.

As with all equipment using electricity, water and moving parts, potential hazards

exist. To safely operate this appliance, become familiar with its operation and

exercise care when using it.

The dishwasher must be properly grounded. Never connect it to an ungrounded

outlet.

2

SAFETY INSTRUCTIONS

Prior to removal of original dishwasher and the installation of your new unit,

make sure to switch off your circuit breaker. Do not connect the dishwasher

until you have completed the installation. Connecting the power cable is the last step

when installing the dishwasher.

All wiring and grounding must be done in accordance with the electrical code

applicable to the region.

Grounding Instructions

For a permanently connected appliance:

This appliance must be connected to grounded metal, a permanent wiring system,

or an equipment-grounding conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on the appliance.

The dishwasher is very heavy. Do not attempt to move or carry a dishwasher alone.

Two or more people are needed to move a dishwasher and avoid potential injuries.

If the power cable is damaged, it must be replaced by the manufacturer,

a service agent or similarly qualified person in order to avoid a hazard.

Do not touch the power cable with wet hands.

CAUTION

Do not connect another appliance to the same power outlet as the

dishwasher.

Make sure to use a new water supply line. Old lines are susceptible to breakage

because they become hardened and may cause property damage due to a water

leakage.

The dishwasher must be connected to a hot water supply with a temperature between

120°F and 149°F. This temperature range provides the best washing result and

shortest cycle time. Temperature should not exceed 149°F to prevent damage to

dishes.

Ensure that the water supplied to the dishwasher does not freeze. Frozen water can

damage the hoses, valves, pump, or other components.

For a full list of safety information, please refer to the User Manual.

3

WARNING

before installing

Do not use the dishwasher until it is correctly installed.
Do not push down on the door when it is open.
Do not place excessive weight on the open door.

Electric Shock Hazard

Failure to follow these instructions can result in death, fire, or electric shock:

Electrically ground the dishwasher.

Connect the ground wire to the green ground connector in the junction box.

Do not use an extension cord.

To reduce the risk of electric shock, fire, or injury to persons, the installer must ensure

that dishwasher is completely enclosed at the time of installation.

4

preparing the dishwasher enclosure

Product Dimensions

The water supply line, power cable, and drain hose should go through the space

behind the dishwasher. The power cable runs in channels under the dishwasher to

connections in the front.

Enclosure Dimensions

This dishwasher is designed to be enclosed on the top and on both sides by a

standard residential kitchen cabinet unit.

The installation enclosure must be clean and free

of any obstructions.

The enclosure must be at least

23.6 inches wide 23 inches

deep and 32.5 inches high.

For the front door of the

dishwasher to be flush with the

leading edge of the counter top,

the counter top must be at least

23 inches deep.

5

installing the dishwasher

Be sure that you or your installer follow these instructions closely so that the new

dishwasher works properly and that you’re not at risk of injury when washing dishes.

Step 1: Check the Parts and Tools

Before starting on the installation, prepare all the necessary tools and parts required

to install the dishwasher. This will save installation time and simplify the installation

process. Below are all the parts that are provided with the dishwasher. See step 5.

Installation Bracket #1 x2 Installation Bracket #2 x2 ST3.9*13 x2

(for the kick plate)

ST4*14 x10

(for install brackets 1&2)

ST3.5*25 x2

(for the decorative door hook)

Cable Tie

(for the drain hose)

ST3.5*9 x2 ST3.5*45 x4

(for the decorative door)

Decorative Door Hook Adjustment Cap x2

Kick Plate Condensation Strip

6

Not Provided:

installing the dishwasher

Twist on wire connector Strain relief

Hot water supply line 90° Elbow Tube fittings

Air gap Rubber connector Hose clamp

Electrical tape & standard

duct tape

Power cable Teflon tape or sealing

compound

Do not use plastic tubing. Plastic tubing can deteriorate over time and cause a

leak inside the tube fitting. We strongly recommend using copper tubing with a

compression fitting or a flexible stainless steel braided hot water supply line.

Decorative door

7

installing the dishwasher

Tools Required (Not Provided):

Electric drill Safety glasses Gloves

Adjustable wrench Wire stripper Pliers

Tape measure

Tubing cutter Cutting knife Hole saw

Torx t20 Hex L-wrench Flashlight

Nipper Flat screwdriver Level

Pencil Phillips screwdriver

8

installing the dishwasher

If the dishwasher is a new installation, most of the installation work must be done

before the dishwasher is moved into place. If the dishwasher is replacing an old

dishwasher, you must check the exising dishwasher connections for compatibility with

the new dishwasher. Replace the existing connections as necessary.

Step 2: Select the Best Location for the Dishwasher

The following criteria are important to ensure the best location for the dishwasher:

The location must have a solid floor that is able to support the weight of the

dishwasher.

The location must be near a sink with easy access to the water supply, drain,

and electrical outlet.

For the drain to operate properly, the dishwasher should be installed within

9.8 ft of the sink.

The location must let you load your dishes into the dishwasher easily.

The location must have sufficient space for the dishwasher door to open

easily and provide enough space between the dishwasher and the

cabinet sides (at least 0.1 in).

If the dishwasher is installed in a corner, ensure that the side of the

dishwasher is more than 2 inches from the wall or cabinet.

The wall at the back must be free of obstructions.

If this is a new installation, follow these steps:

1. Using a hole saw, cut a hole into the side of the cabinet that hold the sink as shown

in Figure 1-1 below.

2. If the base inside the sink cabinet is raised above the kitchen floor and is higher

than the connections on the dishwasher, make a hole in the base inside the cabinet

and in the cabinet side as shown in Figure 1-2.

Depending on where your electrical outlet is, you may need to cut a hole in the

opposite cabinet side.

9

Figure 1-1 Figure 1-2

installing the dishwasher

Step 3: Check Water Supply Requirements and Cautions

The hot water supply line pressure must be between 0.04-1MPa.

Adjust the water heater to deliver water between 120°F ~149°F.

The dishwasher must be connected to a hot water supply between

120°F~149 °F. This temperature range provides the best

washing result and shortest cycle time. Temperature should not

exceed 149°F to prevent damage to dishes.

Ensure that the water supply valve is turned off before connecting the hot

water supply line to the dishwasher.

Seal the hot water supply line connections using teflon tape or sealing

compound to stop any water leakage.

When you install the dishwasher, ensure there is nothing on the drain hose

and be careful not to tear it during the installation process.

Figure 2

10

installing the dishwasher

Step 4: Check the Electrical Requirements and Cautions
The electrical requirements for the dishwasher are as follows:

In the United States, install in accordance with the National Electric Code/State and

Municipal codes and/or local codes.

For cable direct connections.

Use flexible, armored or non-metallic sheathed, copper wire with a

grounding wire that meets the wiring requirements for your local codes and

ordinances.

Use the strain relief method provided with the wiring junction box or install

a U.L.-listed/CSA-certified clamp connector to the wiring junction box. If

using conduit, use a U.L.-listed/CSA-certified conduit connector.

11

installing the dishwasher

Step 5: Unpacking and Inspecting the Dishwasher

Unbox the dishwasher in an open area free of obstruction both around the carton

and overhead. We recommend that you retain the carton and all of the packing

materials until the dishwasher is fully installed and operational to ensure you have

removed all the product’s components from the carton prior to disposal.

Unboxing

1. Unbuckle or cut the four straps securing the carton top.

2. Lift the top of the telescoping carton clear of the carton tray and the contents, and

then turn it over and place it on the floor.

3. Put the straps and all of the packing materials from around the dishwasher inside

the carton top, inspecting them for any signs of damage.

4. Lift the dishwasher from the carton tray, and then place it on the floor. Put the tray

into the carton top.

5. Remove the bag that protects the dishwasher during shipping.

ALWAYS LIFT THE DISHWASHER TO MOVE IT.

Sliding it over rough surfaces can damage the dishwasher’s feet

and sliding the feet over finished surfaces can, in some cases,

CAUTION

damage that finish or the underlying surface.

6. There is also packing inside the dishwasher that you may want to leave in place

until the dishwasher is installed.

7. Do not, under any circumstances, remove the sound-absorbent padding that

surrounds the exterior of the tub of the dishwasher.

Mechanical Inspection

1. Check the plastic base assembly to ensure that it is intact.

2. Check the dishwasher’s feet to ensure they are in place and can be adjusted so

you can level and secure the dishwasher.

3. Check all the visible components on the bottom of the dishwasher to ensure they

are intact and secure.

4. Check the door latch, the operation of the hinges, and confirm the door is properly

secured to the dishwasher.

12