Zippy R1V2-5275V4H User Manual

PRODUCTS MANUAL

R1V2 SERIES

High Density Redundant Power Supply

For 1U Chassis

Rev.:A1

P/N:702-10041

INDEX

1.1 Introduction page 2

1.2 Packing page 3

1.3 Model Designation page 3

1.4 Features page 4

1.5 Pre-Installation page 4

1.6 Drawing page 5 ~ 6

1.7 Specification page 7 ~ 8

1.8 Installation & Testing page 9 ~ 10

1.9 Hot-Swap Procedures page 10 ~ 11

1.10 Pin-outs and function of connectors page 11

1.11 Trouble shooting page 12

1

1.1 INTRODUCTION

First of all, thank you for purchasing R1V2 Series – High-Density Micro
Redundant power supply for 1U chassis.

The R1V2 is a 1+1, Hot-swappable/Hot-pluggable, High-Density Micro
Redundant power supply set, it consists of:

(1) complete metal frame (nickel-plated)
(2) compact size 1+1 power modules
(3) backplane board

The R1V2 Series of hot swappable high-density micro redundant power supply
offer a maximum 275 watts of output power. The R1V2 series provide Active
Power Factor correction (PFC) at full range AC Input complies with
IEC 1000-3-2/3 for critical applications.

The power unit’s size is compact which smaller than PS II form factor and both
power modules built two interior 40X28 m/m ball bearing DC fans. Each power
module has designed with 2 outputs including +12V & 5VSB circuits and higher
current availability based on Intel ATX12V / EPS12V standards. Total set has
designed with 5 outputs including +12V, +5V, +3.3V, -12V & +5VSB circuits

The unit features a warning sub-system, including LED display, buzzer alarm,
TTL signal, etc., at the same time, it guides user the fast way to find out the
power supply and DC fan Good or Fail optional conditions.

To really discover the power and easy in using these products, we recommend
that you read through this manual carefully.

2

1.2 PACKING

Your R1V2 box package should consist of the following:

(A) R1V2 *1
(B) Accessory pack (included 1 holding bracket for shipment)*1
(C) Products’ manual *1

1.3 MODEL DESIGNATION

Model number identification:

R1V2 – 5ZZZV4H

R1V2 --- Model name (AC Input)
5 --- For 5 DC outputs (5V/12V/-12V/3.3V/5VSB) for
ATX12V / EPS12V Spec.
ZZZ --- Total output power, ZZZ -> 275 etc. (unit: watt)
V --- High efficiency.
4H --- Suit for 1U chassis (1U = 44.4 m/m) suit for 1U chassis
horizontal type

3

1.4 FEATURES

R1V2 Series --- High-Density Redundant power supply with Active Power Factor
correction
1+1, Hot swappable, Hot pluggable, AC Input for 1U chassis

Easy fit into 1U , 275W+275W , ATX12V / EPS12V outputs

 Dimension :R1V2 - 295mm(D)×106mm(W)×41.8mm(H)
 True Redundant design (Passive backplane)

 All circuit been designed in the power module
 Hot swap, Hot plug ability
 Full range 90V~264VAC input
 Active Power Factor Correction (PFC) built in
 ATX 275W + 275W output power
 Remote sensing design
 Meet FCC, CISPR EMI regulation
 Compact size for1U chassis
 Space save design
 One 40X28 m/m ball bearing DC fan on power module design
 High-Density

1.5 PRE-INSTALLATION

Before installing the R1V2 unit into the system chassis, please review the
following drawings page 4 ~ 13 and find out the best way to match them.

1.6 DRAWING

.

1.7 SPECIFICATIONS

INPUT CHARACTERISTICS: R1V2-5275V4H

A、INPUT CHARACTERISTICS：

1、VOLTAGE： 90∼264VAC FULL RANGE
2、FREQUENCY： 47∼63HZ
3、INPUT CURRENT：4A (RMS) FOR 115 VAC

2A (RMS) FOR 230 VAC

4、INRUSH CURRE NT：35A MAX. FOR 115 VAC PER MODULE

70A MAX. FOR 230 VAC PER MODULE

B、OUTPUT CHARACTERISTICS：

OUTPUT OUTPUT CURRENT REGULATION OUTPUT RIPPLE &

VOLTAGE MIN. MAX. LOAD LINE NOISE MAX. [P-P]

+5V 0 20 ±5%

+12V

-12V

0.1 22 ±5% ±1%
0 0.3

±10%

+3.3V 0 20 ±5%

+5Vsb 0.1 2.5 ±5%

±1%

±1% 120mV (P-P)
±1% 50mV (P-P)
±1% 50mV (P-P)

50mV (P-P)

120mV (P-P)

REMARK: +5V AND +3.3V TOTAL OUTPUT MAX: 150W / +5V, +3.3V, +12V, -12V TOTAL

OUTPUT MAX: 263W / TOTAL POWER: 275W

C、SPECIFICATION
* TEMPERATURE RANGE：OPERATING 0
* HOLD UP TIME：WHEN POWER SHUTDOWN DC OUTPUT 5V MUST BE MAINTAIN 16MSEC IN
REGULATION LIMIT AT NORMAL INPUT VOLTAGE
* EFFICIENCY：78
* LEAKAGE CURRENT: 3.5 MA. MAX. AT NOMINAL VOLTAGE 250VAC
* POWER GOOD SIGNAL：ON DELAY 100mS TO 550mS，OFF DELAY 1Ms
* OVER POWER PROTECTION：110∼170% MAX
* OVER VOLTAGE PROTECTION: +5V→5.6~6.5V, +3.3V→3.6~4.3V, +12V→13.2~15V
* SHORT CIRCUIT PROTECTION: +5V, +3.3V, +12V, -12V, +5VSB
* SAFETY: MEET UL60950, TUV EN-60950, CB IEC 60950
* WARNING METHOD: AUDIO ALARM (BUZZER SOUND, RESETABLE ), FALUT LED, TTL
* DIMENSION: 295(D)×106(W)×41.8(H) mm

%±2%

TYPICAL，AT FULL LOAD 230VAC

℃∼50℃

, STORAGE -20℃~80℃

1.8 INSTALLATION & TESTING

Turn off (Remote off) the on/off switch.

Mount the power supply in the system chassis using the proper mounting tool,
the mounting holes in the power supply should match those in the case. Attach
the connectors to the M/B by following the M/B instructions, there are various
connectors / pin-outs on both power supply and M/B. They should match each
other; otherwise the connection will cause undetectable harms.

Attach all the remaining power supply connections to the various peripherals as
needed. These connectors are “keyed”, so there will be only one possible way to
connect them.

Before applying power to the system, make sure there are no loose or incorrect
connectors. You do not need to worry about the setting of AC Input because of
the units’ full range features. Double check that all connections to the M/B are
matched properly. Maybe you would like to test the redundancy function before
you put back the cover of your system chassis. Remote on the on/off switch, you
will notice that if the power unit is operating properly, the individual LEDs and
external warning LEDs (please refer to Sec. 1.10 for detail explanation) are lit
Green. Now remove one of the power modules, the warning buzzer in the power
system will sound and the external warning LED which displays the status of the
total power supply system will change to blink, the individual LEDs (on the front
of power module) indicating the power supply’s status will not light. Meanwhile,
the power supply will continue to backup the power output without affecting the
computer system’s operation.

When the warning buzzer sounds, the user can reset the warning buzzer by
pressing the buzzer reset or use the reset switch of the system chassis. The reset
switch can be connected by wires lead provided from the power supply system
(please refer to Sec. 1.10). Insert the power module which is removed for testing
earlier, the sound of the warning buzzer will disappear, the external warning LED
will turn Green again. The LED indicating the status of the power supply will
light again when testing another power supply by performing the similar
procedure.

9

If everything works out fine, then turn off (remote off) the power system. Now
put back the cover of the case and tighten with the screws that you have retained
earlier. Now you have completed the installation of the R1V2 redundant power
supply system.

1.9 HOT-SWAP PROCEDURES

Please refer to the following when either power module or the fan found
defective.

A) Locate the defective power module by examining the individual LED (if LED

without light, it indicates the power module is defective).

***WARNING:

Please perform the above step carefully otherwise it may cause shut down the
whole system.

***WARNING:

Please do not remove the defective power module until you have worn gloves to
keep from be burned. This is due to the cover of the power module is used as heat
sink for cooling, usually the temperature is around 50 ~ 60 degree Celsius under
full load condition.

B) Loosen the bracket screws of the power module
C) Remove the defective power module by pulling out method

***WARNING:

Please put aside the power module await for cooling down. Keep from other
people tough it until it is cool.

10

D) Replace a new Good power module, insert the power module into the power

system to the end.

E) Check the LED of the power module light Green.
F) Check the LED indicating the total power system status. It should be from

twinkle to Green.

G) Tighten the screws of the power module to fix it.
H) If you want to test this new power module in simulating defective situation.

Please refer to the Section 1.8 Installation & Testing Section.

Remarks: If the DC fan of the power module fail, you have to replace the power
module. Please follow with the Hot-Swap procedures of the power module.

1.10 PINOUTS AND FUNCTION OF THE CONNECTORS

*** Please be aware of the polarity***

A. Power module defective signal:
PIN# VOLTAGE SPECIFICATION
1 GND
2 TTL SIGNAL pull up to +5Vsb
Low Active --- Defective
High --- Normal

B. Power status LED:
PIN# VOLTAGE SPECIFICATION
1 GND
2 12V Resistance 1K ohm to +12V
Low Active (blink) --- Defective
High (Green) --- Normal

C. Buzzer reset switch:
PIN# VOLTAGE SPECIFICATION
2 GND
1 5V pull up to +5Vsb
Low Active --- on shoot trigger
TTL signal:
Sink current max. 5mA
Source current max. 50uA
Low Active ---Defective
High ---Normal

11

1.11 TROUBLE SHOOTING

If you have followed these directions correctly, there should be no problem
occurred. Some common symptoms are: the system doesn’t work, buzzer sounds,
work for a very short period, etc., please try the following steps to verify and
correct it:

1. Check all the connections (correct pinouts, loose connections, wrong direction,

etc).

2. Check for short-circuits or defective peripherals by unhooking each peripheral

once at a time. When the systems functions again, you have solved the
problem.

3. Once you hear the buzzer sound or see the LED with blink, please be aware

of :

a. If the load is under the minimum / over the maximum

load of each channel

(please refer the Sec. 1.7 specification)?

b. If each power cord been well plugged into the inlet?

Suppose the above conditions happen, please unplug the power cords, wait for 2
~ 3 minutes for releasing the protection state, then test it again.

c. If buzzer still sounds or the LED shows power module is defective, please

locate the defective power module, perform hot-swap procedure (please refer
to the Sec. 1.9 Hot-swap procedures), sent the defective power module to your
vendor for RMA operation.

d. If you can not fix the problem, please contact with your vendor for supporting.

12

The “RELIABILITY “ solution to E-application

新巨企業股份有限公司

ZIPPY TECHNOLOGY CORP .

POWER DIVISION

HEADQUARTERS

10F, NO. 50, MIN CHYUAN RD., SHIN-TIEN CITY,
TAIPEI HSIEN, TAIWAN, R.O.C.
TEL: [phone] FAX: [phone]
WEB SITE: http://www.zippy.com.tw EMAIL: [e-mail]

USA OFFICE

961 CALLE NEGOCIO, SAN CLEMENTE CA 92673, USA
TEL: [phone] FAX: [phone]
EMAIL: [e-mail]

Note:

*The description stated herein is subject to change without prior notice.
*All brand names and trademarks are the property of their respective owners.

13