1.1 INTRODUCTION
First of all, thank you for purchasing MyWx series redundant power supply.
The MyWx series is a N+1 hot-swappable / hot-pluggable redundant power supply. It
consists of,
The total output is up to your power’s requirements, you can figure out the total
Power’s consumption and check over the specification, the you can find out the
correct configuration.
It delivers full safety redundant (hot-swappable) function and provides the
hot-pluggable feature. In other words, it can offer a more reliable and safer, easy
install / maintain operation in the power energy supply to your system.
Its major function is to deliver the full power and the mean time these power modules
can mutually backup once one of the power modules is defective.
It provides a warning subsystem, include LED display, buzzer alarm, TTL signal etc.,
at the same time, it also indicates the status of the power system.
When all the power modules are at normal condition, it balances the load share and
results the power system increase reliability.
To really discover the power and ease in using the product, we recommend that
you read through this manual carefully.
1.2 PACKING
Your MyWx package should consist of the followings:
(A) MyWx series x 1
(B) Accessory pack x 1
(C) Product Manual x 1
1.3 MODEL DESINGATION
Model number identification
X X Y Z X – X XXX X X X
1 2 3 4 5 6 7 8 9 10
1st --- Category
X --- blank AC input ( AC – DC )
D -48Vdc input
B -24Vdc input
2nd --- Serial ID
X --- R redundant 1 + 1
M redundant N + 1
3rd --- for # U use
Y --- 1 for 1U use
2 for 2U use
4th --- PM or Customer specify
5th --- # of power module in N+1 system
X --- 1 single
2 1+1 power system
3 2+1 power system
4 3+1 power system
6th --- # of the channel
X --- 2 5V, 12V ( Disk Array )
4 5V, 12V, -5V, -12V ( AT )
5 5V, 12V, 3.3V, 5Vsb, -12V ( ATX / EPS )
6 5V, 12V, 3.3V, 5Vsb, -5V, -12V ( ATX / EPS )
7th --- # of total wattages
XXX --- 460
AXX --- 10XX
BXX --- 11XX
CXX --- 12XX
………
8th --- attribute
X --- P w/ PFC
F w/ EMI filter
9th --- chassis type
X --- H horizontal type
V vertical type
M horizontal + vertical type
10th --- Use FAN type
X --- 3 use 3.8CM type
4 use 4CM type
6 use 6CM type
8 use 8CM type
1.4 FEATURES
MyWx
N+1,Hot-swap, Hot-plug, AC input mini redundant power system
l Low profile power module for building to the requirement
l N+1 power system design
l Current sharing design
l Remote sensing design
l 5 channels ( 5/12/-12/3.3/5Vsb ) 600W power module outputs
l 6 channels ( 5/12/-5/-12/3.3/5Vsb ) 500W/550W/950W/1350W/1800W power
module outputs
l Active power factor correction (PFC) built-in
l Universal AC power input
l Warning methods---LED, buzzer. TTL signal
l UL, UL+C, TUV, CB approved
l Meet FCC class B, CISPR 22 class B
l Truly redundant feature design
l Debounce power disturbance keep from shut-down / reset
l Isolated fence in power housing meets the safety regulation
l Double protection on OCP & OVP
l I2C function (optional)
1.5 DRAWING
1.6 SPECIFICATIONS
INPUT CHARACTERISTICS: M1W-6500P
l VOLTAGE: 100V ~ 240VAC (WITH ± 10% TOLERANCE)
l FREQUENCY: 47Hz ~ 63Hz
l INPUT CURRENT: 8.0-4.0A MAX AT ANY LOW/HIGH INPUT VOLTAGE
l INRUSH CURRENT: 60/100A @ 115/230VAC (25℃)
l POWER FACTOR CORRECTION: 95% @ 110V, FULL LOAD
OUTPUT CHARACTERISTICS:
OUTPUT
OUTPUT CURRENT REGULATION OUTPUT
VOLTAGE
MIN. [A] MAX. [A] LOAD LINE
±
5%
6%
5V 3.5 30 ±
12V 2.0 32
-5V 0.05 0.7 +5%, -10%
-12V 0.05 0.7 +5%, -10%
3.3V 1.0 24
±
5%
+5VSB 0.1 2.0 +5%, -6%
REMARKS:
1. THE OUTPUT POWER OF 5V & 3.3V MAX: 40A
2. TOTAL OUTPUT MAX: 500W
SPECIFICATION:
l TEMPERATURE RANGE: OPERATING: 0℃ --- 40℃
50mV
±
50mV
±
50mV
±
50mV
±
50mV
±
50mV
±
RIPPLE & NOISE
MAX. [P-P]
70mV
120mV
120mV
120mV
70mV
70mV
STORAGE: -20℃ --- 80℃
l HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE
l DIELECTRIC WITHSTAND: INPUT / OUTPUT 1500 VAC FOR 1 SECOND
INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND
l EFFICIENCY: 65% TYPICAL AT 115VAC FULL LOAD
l POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms
l OVER POWER PROTECTION: 110% ~ 180%
OVER VOLTAGE PROTECTION: +5V à 5.7V ~ 6.5V, 3.3V à 3.9V ~ 4.7V
+12V à 13.3V ~ 14.3V
OVER CURRENT PROTECTION: 110% ~ 180%
l SHORT CIRCUIT PROTECTION: +5V, -5V, +12V, -12V, +3.3V
l EMI NOISE FILTER: FCC CLASS A, CISPR22 CLASS A
l SAFETY: UL 1950, CSA 22.2 NO/ 950, TÜV IEC 950
l REMOTE ON / OFF CONTROL
THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE /
ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),
AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,
AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABLE.
l 3.3V / 5V REMOTE SENSING
l COOLING: ONE 38mm DC FAN
l DIMENSION: 265.3 (D) x 98.4 (W) x 40 (H) mm
INPUT CHARACTERISTICS: M1W3-6500P
l VOLTAGE: 100V ~ 240VAC
l FREQUENCY: 47Hz ~ 63Hz
l INPUT CURRENT: 20-10A MAX AT ANY LOW/HIGH INPUT VOLTAGE
l INRUSH CURRENT: 60/100A @ 115/230VAC (25℃)
l POWER FACTOR CORRECTION: 95% @ 110V, FULL LOAD
OUTPUT CHARACTERISTICS:
OUTPUT
VOLTAGE
OUTPUT CURRENT REGULATION OUTPUT
MIN. [A] MAX. [A] LOAD LINE
RIPPLE & NOISE
MAX. [P-P]
5V 3.5 30 ± 5% ± 50mV 70mV
12V 2.0 32 ± 6% ± 50mV 120mV
-5V 0.05 0.7 +5%, -10% ± 50mV 120mV
-12V 0.1 0.7 +5%, -10% ± 50mV 120mV
3.3V 1.0 24 ± 5% ± 50mV 70mV
+5VSB 0.1 2.0 +5%, -6% ± 50mV 70mV
REMARKS:
1. THE OUTPUT POWER OF 5V & 3.3V MAX: 40A
2. EACH POWER MODULE OUTPUT MAX: 500W
3. TOTAL OUTPUT POWER MAX: 500W
4. 2 MODULE AND PLUS 1 DUMMY
SPECIFICATION:
l TEMPERATURE RANGE: OPERATING: 0℃ --- 40℃
STORAGE: -20℃ --- 80℃
l HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE
l DIELECTRIC WITHSTAND: INPUT / OUTPUT 3000 VAC FOR 1 SECOND
INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND
l EFFICIENCY: 67% TYPICAL AT 115VAC FULL LOAD
l POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms
l OVER POWER PROTECTION: 110% ~ 180%
OVER VOLTAGE PROTECTION: +5V à 5.7V ~ 6.5V, 3.3V à 3.9V ~ 4.7V
+12V à 13.3V ~ 14.3V
OVER CURRENT PROTECTION: 110% ~ 180%
l SHORT CIRCUIT PROTECTION: +5V, -5V, +12V, -12V, +3.3V
l EMI NOISE FILTER: FCC CLASS A, CISPR22 CLASS A
l SAFETY: UL 1950, CSA 22.2 NO/ 950, TÜV IEC 950
l REMOTE ON / OFF CONTROL
THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE /
ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),
AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,
AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABL
l 3.3V REMOTE SENSING
l DIMENSION: 330 (D) x 383 (W) x 43 (H) mm
INPUT CHARACTERISTICS: M1W3-6950P
l VOLTAGE: 100V ~ 240VAC
l FREQUENCY: 47Hz ~ 63Hz
l INPUT CURRENT: 20-10A MAX AT ANY LOW/HIGH INPUT VOLTAGE
l INRUSH CURRENT: 60/100A @ 115/230VAC (25℃)
l POWER FACTOR CORRECTION: 95% @ 110V, FULL LOAD
OUTPUT CHARACTERISTICS:
OUTPUT
VOLTAGE
OUTPUT CURRENT REGULATION OUTPUT
MIN. [A] MAX. [A] LOAD LINE
RIPPLE & NOISE
MAX. [P-P]
5V 6.0 56 ± 5% ± 50mV 70mV
12V 6.0 60 ± 6% ± 50mV 120mV
-5V 0.2 1.2 +5%, -10% ± 50mV 120mV
-12V 0.2 1.2 +5%, -10% ± 50mV 120mV
3.3V 3.5 44 ± 5% ± 50mV 70mV
+5VSB 0.4 3.5 +5%, -6% ± 50mV 70mV
REMARKS:
5. THE OUTPUT POWER MODULE OF 5V & 3.3V MAX: 40A
2. EACH POWER MODULE OUTPUT MAX: 500W
3. TOTAL OUTPUT POWER MAX: 950W
SPECIFICATION:
l TEMPERATURE RANGE: OPERATING: 0℃ --- 40℃
STORAGE: -20℃ --- 80℃
l HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE
l DIELECTRIC WITHSTAND: INPUT / OUTPUT 3000 VAC FOR 1 SECOND
INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND
l EFFICIENCY: 67% TYPICAL AT 115VAC FULL LOAD
l POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms
l OVER POWER PROTECTION: 110% ~ 180%
OVER VOLTAGE PROTECTION: +5V à 5.7V ~ 6.5V, 3.3V à 3.9V ~ 4.7V
+12V à 13.3V ~ 14.3V
OVER CURRENT PROTECTION: 110% ~ 180%
l SHORT CIRCUIT PROTECTION: +5V, -5V, +12V, -12V, +3.3V
l EMI NOISE FILTER: FCC CLASS A, CISPR22 CLASS A
l SAFETY: UL 1950, CSA 22.2 NO/ 950, TÜV IEC 950
l REMOTE ON / OFF CONTROL
THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE /
ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),
AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,
AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABL
l 3.3V REMOTE SENSING
l DIMENSION: 330 (D) x 383 (W) x 43 (H) mm
INPUT CHARACTERISTICS: M1W3-6D50P
l VOLTAGE: 100V ~ 240VAC
l FREQUENCY: 47Hz ~ 63Hz
l INPUT CURRENT: 20-10A MAX AT ANY LOW/HIGH INPUT VOLTAGE
l INRUSH CURRENT: 60/100A @ 115/230VAC (25℃)
l POWER FACTOR CORRECTION: 95% @ 110V, FULL LOAD
OUTPUT CHARACTERISTICS:
OUTPUT
VOLTAGE
OUTPUT CURRENT REGULATION OUTPUT
MIN. [A] MAX. [A] LOAD LINE
RIPPLE & NOISE
MAX. [P-P]
5V 6.0 84.5 ± 5% ± 50mV 70mV
12V 6.0 90 ± 6% ± 50mV 120mV
-5V 0.2 1.2 +5%, -10% ± 50mV 120mV
-12V 0.2 1.2 +5%, -10% ± 50mV 120mV
3.3V 3.5 67.5 ± 5% ± 50mV 70mV
+5VSB 0.4 3.5 +5%, -6% ± 50mV 70mV
REMARKS:
6. THE OUTPUT POWER MODULE OF 5V & 3.3V MAX: 40A
2. EACH POWER MODULE OUTPUT MAX: 500W
3. TOTAL OUTPUT POWER MAX: 1350W
SPECIFICATION:
l TEMPERATURE RANGE: OPERATING: 0℃ --- 40℃
STORAGE: -20℃ --- 80℃
l HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE
l DIELECTRIC WITHSTAND: INPUT / OUTPUT 3000 VAC FOR 1 SECOND
INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND
l EFFICIENCY: 67% TYPICAL AT 115VAC FULL LOAD
l POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms
l OVER POWER PROTECTION: 110% ~ 180%
OVER VOLTAGE PROTECTION: +5V à 5.7V ~ 6.5V, 3.3V à 3.9V ~ 4.7V
+12V à 13.3V ~ 14.3V
OVER CURRENT PROTECTION: 110% ~ 180%
l SHORT CIRCUIT PROTECTION: +5V, -5V, +12V, -12V, +3.3V
l EMI NOISE FILTER: FCC CLASS A, CISPR22 CLASS A
l SAFETY: UL 1950, CSA 22.2 NO/ 950, TÜV IEC 950
l REMOTE ON / OFF CONTROL
THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE /
ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),
AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,
AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABL
l 3.3V REMOTE SENSING
l DIMENSION: 330 (D) x 383 (W) x 43 (H) mm
INPUT CHARACTERISTICS: M1W3-5B40P3H
l VOLTAGE： 90∼264VAC FULL RANGE
l FREQUENCY： 47∼63HZ
l INPUT CURRENT (PER POWER MODULE)：10/5A FOR 115/230VAC
l INRUSH CURRENT (PER POWER MODULE)：160/180A MAX. FOR 115/230VAC (25℃)
OUTPUT CHARACTERISTICS:
OUTPUT CURRENT REGULATION OUTPUT OUTPUT
VOLTAGE
MIN. MAX. LOAD LINE RIPPLE & NOISE
MAX. [P-P]
+5V 3A 60A
+12V 6A 80A
-12V 0A 1.5A
+3.3V 3A 45A
+5VSB 0.3A 3A
±5% ±50mV
±5% ±50mV
±5% ±50mV
±5% ±50mV
±5% ±50mV
50mV
70mV
70mV
50mV
50mV
REMARKS:
1. TOTAL MAX OUTPUT OF +5V AND +3.3V NOT EXCEED 400W.
2. POWER MODULE TOTAL OUTPUT POWER NOT EXCEED 1140W.
SPECIFICATION:
l TEMPERATURE RANGE：OPERATING 0℃∼40℃，STORAGE -20℃∼80℃
l HOLD UP TIME：16mS MIN.
l DIELECTRIC WITHSTAND：INPUT/OUTPUT 1500 VAC FOR 1 MINUTE
INPUT TO FRAME GROUND 1500 VAC FOR 1 MINUTE
l EFFICIENCY：65% TYPICAL，AT FULL LOAD
l POWER GOOD SIGNAL：ON DELAY 100mS TO 500mS，OFF DELAY 1mS
l OVERLOAD PROTECTION：110∼150% MAX
l OVER VOLTAGE PROTECTION：+5V→5.7V∼6.5V，+3.3V→3.7V∼4.3V ，
+12V→13.3 V∼15V
l OVER CURRENT PROTECTION: +5V,+12V,+3.3V 110~ 150% AT FULL LOAD
l REMOTE ON / OFF CONTROL
l REMOTE SENSING DESIGN
l BALANCE LOAD SHARING DESIGN
l HOT-SWAPPABLE/HOT PLUGGABLE REDUNDANCY FUNCTION
l ISOLATION: BUILT-IN THE POWER MODULE
l FAULTY ALARM METHODS: LED, BUZZER, TTL SIGNAL
l DIMENSION：43*383*330 (H*W*D)mm
l COOLING: TWO 38*28mm DC FAN (MODULE)
l AC INLET IN EACH MODULE
l EMI NOISE FILTER: FCC CLASS B , CISPR 22 CLASS B
l MEET IEC-1000-3-2 CLASS D (ACTIVE PFC)
l SAFETY：MEET UL1950,CSA22.2NO/950,TUV IEC950
INPUT CHARACTERISTICS: M1W3-5B40P3V
l VOLTAGE：90∼264VAC FULL RANGE
l FREQUENCY：47∼63HZ
l INPUT CURRENT (PER POWER MODULE)：10/5A FOR 115/230VAC
l INRUSH CURRENT (PER POWER MODULE)：160/180A MAX. FOR 115/230VAC (25℃)
OUTPUT CHARACTERISTICS:
OUTPUT CURRENT REGULATION OUTPUT OUTPUT
VOLTAGE
MIN. MAX. LOAD LINE RIPPLE & NOISE
MAX. [P-P]
+5V 3A 60A
+12V 6A 80A
-12V 0A 1.5A
+3.3V 3A 45A
+5VSB 0.3A 3A
±5% ±50mV
±5% ±50mV
±5% ±50mV
±5% ±50mV
±5% ±50mV
50mV
70mV
70mV
50mV
50mV
REMARKS:
1. TOTAL MAX OUTPUT OF +5V AND +3.3V NOT EXCEED 400W.
2. POWER MODULE TOTAL OUTPUT POWER NOT EXCEED 1140W.
SPECIFICATION:
l TEMPERATURE RANGE：OPERATING 0℃∼40℃，STORAGE -20℃∼80℃
l HOLD UP TIME：16mS MIN.
l DIELECTRIC WITHSTAND：INPUT/OUTPUT 1500 VAC FOR 1 MINUTE
INPUT TO FRAME GROUND 1500 VAC FOR 1 MINUTE
l EFFICIENCY：65% TYPICAL，AT FULL LOAD
l POWER GOOD SIGNAL：ON DELAY 100mS TO 500mS，OFF DELAY 1mS
l OVERLOAD PROTECTION：110∼150% MAX
l OVER VOLTAGE PROTECTION：+5V→5.7V∼6.5V，+3.3V→3.7V∼4.3V ，
l +12V→13.3 V∼15V
l VER CURRENT PROTECTION: +5V,+12V,+3.3V 110~ 150% AT FULL LOAD
l REMOTE ON / OFF CONTROL
l REMOTE SENSING DESIGN
l BALANCE LOAD SHARING DESIGN
l HOT-SWAPPABLE/HOT PLUGGABLE REDUNDANCY FUNCTION
l ISOLATION: BUILT-IN THE POWER MODULE
l FAULTY ALARM METHODS: LED, BUZZER, TTL SIGNAL
l DIMENSION：125*101*300 (H*W*D)mm
l COOLING: TWO 38*28mm DC FAN (MODULE)
l AC INLET IN EACH MODULE
l EMI NOISE FILTER: FCC CLASS B , CISPR 22 CLASS B
l MEET IEC-1000-3-2 CLASS D (ACTIVE PFC)
l SAFETY：MEET UL1950,CSA22.2NO/950,TUV IEC950
INPUT CHARACTERISTICS: M1W4-6500P
l VOLTAGE: 100V ~ 240VAC
l FREQUENCY: 47Hz ~ 63Hz
l INPUT CURRENT: 20-10A MAX AT ANY LOW/HIGH INPUT VOLTAGE
l INRUSH CURRENT: 60/100A @ 115/230VAC (25℃)
l POWER FACTOR CORRECTION: 95% @ 110V, FULL LOAD
OUTPUT CHARACTERISTICS:
OUTPUT
VOLTAGE
OUTPUT CURRENT REGULATION OUTPUT
MIN. [A] MAX. [A] LOAD LINE
RIPPLE & NOISE
MAX. [P-P]
5V 3.5 30 ± 5% ± 50mV 70mV
12V 2.0 32 ± 6% ± 50mV 120mV
-5V 0.05 0.7 +5%, -10% ± 50mV 120mV
-12V 0.1 0.7 +5%, -10% ± 50mV 120mV
3.3V 1.0 24 ± 5% ± 50mV 70mV
+5VSB 0.1 2.0 +5%, -6% ± 50mV 70mV
REMARKS:
7. THE OUTPUT POWER OF 5V & 3.3V MAX: 40A
8. EACH POWER MODULE OUTPUT MAX: 500W
9. TOTAL OUTPUT POWER MAX: 500W
10. 2 MODULE AND PLUS 2 DUMMY
SPECIFICATION:
l TEMPERATURE RANGE: OPERATING: 0℃ --- 40℃
STORAGE: -20℃ --- 80℃
l HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE
l DIELECTRIC WITHSTAND: INPUT / OUTPUT 3000 VAC FOR 1 SECOND
INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND
l EFFICIENCY: 67% TYPICAL AT 115VAC FULL LOAD
l POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms
l OVER POWER PROTECTION: 110% ~ 180%
OVER VOLTAGE PROTECTION: +5V à 5.7V ~ 6.5V, 3.3V à 3.9V ~ 4.7V
+12V à 13.3V ~ 14.3V
OVER CURRENT PROTECTION: 110% ~ 180%
l SHORT CIRCUIT PROTECTION: +5V, -5V, +12V, -12V, +3.3V
l EMI NOISE FILTER: FCC CLASS A, CISPR22 CLASS A
l SAFETY: UL 1950, CSA 22.2 NO/ 950, TÜV IEC 950
l REMOTE ON / OFF CONTROL
THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE /
ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),
AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,
AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABL
l 3.3V REMOTE SENSING
l DIMENSION: 340 (D) x 422 (W) x 43 (H) mm
INPUT CHARACTERISTICS: M1W4-6950P
l VOLTAGE: 100V ~ 240VAC
l FREQUENCY: 47Hz ~ 63Hz
l INPUT CURRENT: 20-10A MAX AT ANY LOW/HIGH INPUT VOLTAGE
l INRUSH CURRENT: 60/100A @ 115/230VAC (25℃)
l POWER FACTOR CORRECTION: 95% @ 110V, FULL LOAD
OUTPUT CHARACTERISTICS:
OUTPUT
VOLTAGE
OUTPUT CURRENT REGULATION OUTPUT
MIN. [A] MAX. [A] LOAD LINE
RIPPLE & NOISE
MAX. [P-P]
5V 6.0 56 ± 5% ± 50mV 70mV
12V 6.0 60 ± 6% ± 50mV 120mV
-5V 0.2 1.2 +5%, -10% ± 50mV 120mV
-12V 0.2 1.2 +5%, -10% ± 50mV 120mV
3.3V 3.5 44 ± 5% ± 50mV 70mV
+5VSB 0.4 3.5 +5%, -6% ± 50mV 70mV
REMARKS:
11. THE OUTPUT POWER OF 5V & 3.3V MAX: 40A
12. EACH POWER MODULE OUTPUT MAX: 500W
13. TOTAL OUTPUT POWER MAX: 950W
14. 2 MODULE AND PLUS 1 DUMMY
SPECIFICATION:
l TEMPERATURE RANGE: OPERATING: 0℃ --- 40℃
STORAGE: -20℃ --- 80℃
l HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE
l DIELECTRIC WITHSTAND: INPUT / OUTPUT 3000 VAC FOR 1 SECOND
INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND
l EFFICIENCY: 67% TYPICAL AT 115VAC FULL LOAD
l POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms
l OVER POWER PROTECTION: 110% ~ 180%
OVER VOLTAGE PROTECTION: +5V à 5.7V ~ 6.5V, 3.3V à 3.9V ~ 4.7V
+12V à 13.3V ~ 14.3V
OVER CURRENT PROTECTION: 110% ~ 180%
l SHORT CIRCUIT PROTECTION: +5V, -5V, +12V, -12V, +3.3V
l EMI NOISE FILTER: FCC CLASS A, CISPR22 CLASS A
l SAFETY: UL 1950, CSA 22.2 NO/ 950, TÜV IEC 950
l REMOTE ON / OFF CONTROL
THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE /
ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),
AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,
AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABL
l 3.3V REMOTE SENSING
l DIMENSION: 340 (D) x 422 (W) x 43 (H) mm
INPUT CHARACTERISTICS: M1W4-6D50P
l VOLTAGE: 100V ~ 240VAC
l FREQUENCY: 47Hz ~ 63Hz
l INPUT CURRENT: 20-10A MAX AT ANY LOW/HIGH INPUT VOLTAGE
l INRUSH CURRENT: 60/100A @ 115/230VAC (25℃)
l POWER FACTOR CORRECTION: 95% @ 110V, FULL LOAD
OUTPUT CHARACTERISTICS:
OUTPUT
VOLTAGE
OUTPUT CURRENT REGULATION OUTPUT
MIN. [A] MAX. [A] LOAD LINE
RIPPLE & NOISE
MAX. [P-P]
5V 6.0 84.5 ± 5% ± 50mV 70mV
12V 6.0 90 ± 6% ± 50mV 120mV
-5V 0.2 1.2 +5%, -10% ± 50mV 120mV
-12V 0.2 1.2 +5%, -10% ± 50mV 120mV
3.3V 3.5 67.5 ± 5% ± 50mV 70mV
+5VSB 0.4 3.5 +5%, -6% ± 50mV 70mV
REMARKS:
15. THE OUTPUT POWER OF 5V & 3.3V MAX: 40A
16. EACH POWER MODULE OUTPUT MAX: 500W
17. TOTAL OUTPUT POWER MAX: 1350W
SPECIFICATION:
l TEMPERATURE RANGE: OPERATING: 0℃ --- 40℃
STORAGE: -20℃ --- 80℃
l HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE
l DIELECTRIC WITHSTAND: INPUT / OUTPUT 3000 VAC FOR 1 SECOND
INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND
l EFFICIENCY: 67% TYPICAL AT 115VAC FULL LOAD
l POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms
l OVER POWER PROTECTION: 110% ~ 180%
OVER VOLTAGE PROTECTION: +5V à 5.7V ~ 6.5V, 3.3V à 3.9V ~ 4.7V
+12V à 13.3V ~ 14.3V
OVER CURRENT PROTECTION: 110% ~ 180%
l SHORT CIRCUIT PROTECTION: +5V, -5V, +12V, -12V, +3.3V
l EMI NOISE FILTER: FCC CLASS A, CISPR22 CLASS A
l SAFETY: UL 1950, CSA 22.2 NO/ 950, TÜV IEC 950
l REMOTE ON / OFF CONTROL
THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE /
ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),
AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,
AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABL
l 3.3V REMOTE SENSING
l DIMENSION: 340 (D) x 422 (W) x 43 (H) mm
INPUT CHARACTERISTICS: M1W4-6I00P
l VOLTAGE: 100V ~ 240VAC
l FREQUENCY: 47Hz ~ 63Hz
l INPUT CURRENT: 20-10A MAX AT ANY LOW/HIGH INPUT VOLTAGE
l INRUSH CURRENT: 60/100A @ 115/230VAC (25℃)
l POWER FACTOR CORRECTION: 95% @ 110V, FULL LOAD
OUTPUT CHARACTERISTICS:
OUTPUT
VOLTAGE
OUTPUT CURRENT REGULATION OUTPUT
MIN. [A] MAX. [A] LOAD LINE
RIPPLE & NOISE
MAX. [P-P]
5V 6.0 84.5 ± 5% ± 50mV 70mV
12V 6.0 90 ± 6% ± 50mV 120mV
-5V 0.2 1.2 +5%, -10% ± 50mV 120mV
-12V 0.2 1.2 +5%, -10% ± 50mV 120mV
3.3V 3.5 67.5 ± 5% ± 50mV 70mV
+5VSB 0.4 3.5 +5%, -6% ± 50mV 70mV
REMARKS:
18. THE OUTPUT POWER OF 5V & 3.3V MAX: 40A
19. EACH POWER MODULE OUTPUT MAX: 500W
20. TOTAL OUTPUT POWER MAX: 1800W
SPECIFICATION:
l TEMPERATURE RANGE: OPERATING: 0℃ --- 40℃
STORAGE: -20℃ --- 80℃
l HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE
l DIELECTRIC WITHSTAND: INPUT / OUTPUT 3000 VAC FOR 1 SECOND
INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND
l EFFICIENCY: 67% TYPICAL AT 115VAC FULL LOAD
l POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms
l OVER POWER PROTECTION: 110% ~ 180%
OVER VOLTAGE PROTECTION: +5V à 5.7V ~ 6.5V, 3.3V à 3.9V ~ 4.7V
+12V à 13.3V ~ 14.3V
OVER CURRENT PROTECTION: 110% ~ 180%
l SHORT CIRCUIT PROTECTION: +5V, -5V, +12V, -12V, +3.3V
l EMI NOISE FILTER: FCC CLASS A, CISPR22 CLASS A
l SAFETY: UL 1950, CSA 22.2 NO/ 950, TÜV IEC 950
l REMOTE ON / OFF CONTROL
THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE /
ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),
AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,
AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABL
l 3.3V REMOTE SENSING
l DIMENSION: 340 (D) x 422 (W) x 43 (H) mm
INPUT CHARACTERISTICS: M1W4-5B40P3H
l VOLTAGE： 90∼264VAC FULL RANGE
l FREQUENCY： 47∼63HZ
l INPUT CURRENT (PER POWER MODULE)：10/5A FOR 115/230VAC
l INRUSH CURRENT (PER POWER MODULE)：160/180A MAX. FOR 115/230VAC (25℃)
OUTPUT CHARACTERISTICS:
OUTPUT CURRENT REGULATION OUTPUT OUTPUT
VOLTAGE
MIN. MAX. LOAD LINE RIPPLE & NOISE
MAX. [P-P]
+5V 3A 60A
+12V 6A 80A
-12V 0A 1.5A
+3.3V 3A 45A
+5VSB 0.3A 3A
±5% ±50mV
±5% ±50mV
±5% ±50mV
±5% ±50mV
±5% ±50mV
50mV
70mV
70mV
50mV
50mV
REMARKS:
21. TOTAL MAX OUTPUT OF +5V AND +3.3V NOT EXCEED 400W.
22. POWER MODULE TOTAL OUTPUT POWER NOT EXCEED 1140W.
SPECIFICATION:
l TEMPERATURE RANGE：OPERATING 0℃∼40℃，STORAGE -20℃∼80℃
l HOLD UP TIME：16mS MIN.
l DIELECTRIC WITHSTAND：INPUT/OUTPUT 1500 VAC FOR 1 MINUTE
INPUT TO FRAME GROUND 1500 VAC FOR 1 MINUTE
l EFFICIENCY：65% TYPICAL，AT FULL LOAD
l POWER GOOD SIGNAL：ON DELAY 100mS TO 500mS，OFF DELAY 1mS
l OVERLOAD PROTECTION：110∼150% MAX
l OVER VOLTAGE PROTECTION：+5V→5.7V∼6.5V，+3.3V→3.7V∼4.3V ，+12V→13.3 V∼15V
l OVER CURRENT PROTECTION: +5V,+12V,+3.3V 110~ 150% AT FULL LOAD
l REMOTE ON / OFF CONTROL
l REMOTE SENSING DESIGN
l BALANCE LOAD SHARING DESIGN
l HOT-SWAPPABLE/HOT PLUGGABLE REDUNDANCY FUNCTION
l ISOLATION: BUILT-IN THE POWER MODULE
l FAULTY ALARM METHODS: LED, BUZZER, TTL SIGNAL
l DIMENSION：43*422*340 (H*W*D)mm
l COOLING: TWO 38*28mm DC FAN (MODULE)
l AC INLET IN EACH MODULE
l EMI NOISE FILTER: FCC CLASS B , CISPR 22 CLASS B
l MEET IEC-1000-3-2 CLASS D (ACTIVE PFC)
l SAFETY：MEET UL1950,CSA22.2NO/950,TUV IEC950ISOLATION: BUILT-IN THE POWER
MODULE
INPUT CHARACTERISTICS: M1W4-5B40P3V
l VOLTAGE：90∼264VAC FULL RANGE
l FREQUENCY：47∼63HZ
l INPUT CURRENT (PER POWER MODULE) ：10/5A FOR 115/230VAC
l INRUSH CURRENT (PER POWER MODULE)：160/180A MAX. FOR 115/230VAC (25℃)
OUTPUT CHARACTERISTICS:
OUTPUT CURRENT REGULATION OUTPUT OUTPUT
VOLTAGE
MIN. MAX. LOAD LINE RIPPLE & NOISE
MAX. [P-P]
+5V 3A 60A
+12V 6A 80A
-12V 0A 1.5A
+3.3V 3A 45A
+5VSB 0.3A 3A
±5% ±50mV
±5% ±50mV
±5% ±50mV
±5% ±50mV
±5% ±50mV
50mV
70mV
70mV
50mV
50mV
REMARKS:
23. TOTAL MAX OUTPUT OF +5V AND +3.3V NOT EXCEED 400W.
24. POWER MODULE TOTAL OUTPUT POWER NOT EXCEED 1140W.
SPECIFICATION:
l TEMPERATURE RA NGE：OPERATING 0℃∼40℃，STORAGE -20℃∼80℃
l HOLD UP TIME：16mS MIN.
l DIELECTRIC WITHSTAND：INPUT/OUTPUT 1500 VAC FOR 1 MINUTE
INPUT TO FRAME GROUND 1500 VAC FOR 1 MINUTE
l EFFICIENCY：65% TYPICAL，AT FULL LOAD
l POWER GOOD SIGNAL：ON DELAY 100mS TO 500mS，OFF DELAY 1mS
l OVERLOAD PROTECTION：110∼150% MAX
l OVER VOLTAGE PROTECTION：+5V→5.7V∼6.5V，+3.3V→3.7V∼4.3V ，+12V→13.3 V∼15V
l OVER CURRENT PROTECTION: +5V,+12V,+3.3V 110~ 150% AT FULL LOAD
l REMOTE ON / OFF CONTROL
l REMOTE SENSING DESIGN
l BALANCE LOAD SHARING DESIGN
l HOT-SWAPPABLE/HOT PLUGGABLE REDUNDANCY FUNCTION
l ISOLATION: BUILT-IN THE POWER MODULE
l FAULTY ALARM METHODS: LED, BUZZER, TTL SIGNAL
l DIMENSION：166*101*300 (H*W*D)mm
l COOLING: TWO 38*28mm DC FAN (MODULE)
l AC INLET IN EACH MODULE
l EMI NOISE FILTER: FCC CLASS B , CISPR 22 CLASS B
l MEET IEC-1000-3-2 CLASS D (ACTIVE PFC)
l SAFETY：MEET UL1950,CSA22.2NO/950,TUV IEC950
INPUT CHARACTERISTICS: M1W4-5G20P3H
l VOLTAGE：90∼264VAC FULL RANGE
l FREQUENCY：47∼63HZ
l INPUT CURRENT (PER POWER MODULE)：10/5A FOR 115/230VAC
l INRUSH CURRENT (PER POWER MODULE)：160/180A MAX.FOR 115/230 VAC (25℃)
OUTPUT CHARACTERISTICS:
OUTPUT CURRENT REGULATION OUTPUT OUTPUT
VOLTAGE
MIN. MAX. LOAD LINE RIPPLE & NOISE
MAX. [P-P]
+5V 4A 85A
+12V 8A 115A
-12V 0A 2A
+3.3V 4A 65A
+5VSB 0.4A 3.5A
±5% ±50mV
±5% ±50mV
±5% ±50mV
±5% ±50mV
±5% ±50mV
50mV
70mV
70mV
50mV
50mV
REMARKS:
25. TOTAL MAX OUTPUT OF +5V AND +3.3V NOT EXCEED 560W.
26. POWER MODULE TOTAL OUTPUT POWER NOT EXCEED 1620W.
SPECIFICATION:
l TEMPERATURE RANGE：OPERATING 0℃∼40℃，STORAGE -20℃∼80℃
l HOLD UP TIME：16mS MIN.
l DIELECTRIC WITHSTAND：INPUT/OUTPUT 1500 VAC FOR 1 MINUTE
INPUT TO FRAME GROUND 1500 VAC FOR 1 MINUTE
l EFFICIENCY：65% TYPICAL，AT FULL LOAD
l POWER GOOD SIGNAL：ON DELAY 100mS TO 500mS，OFF DELAY 1mS
l OVERLOAD PROTECTION：110∼150% MAX
l OVER VOLTAGE PROTECTION：+5V→5.7V∼6.5V，+3.3V→3.7V∼4.3V ，
+12V→13.3 V∼15V
l OVER CURRENT PROTECTION: +5V,+12V,+3.3V 110~ 150% AT FULL LOAD
l REMOTE ON / OFF CONTROL
l REMOTE SENSING DESIGN
l BALANCE LOAD SHARING DESIGN
l HOT-SWAPPABLE/HOT PLUGGABLE REDUNDANCY FUNCTION
l ISOLATION: BUILT-IN THE POWER MODULE
l FAULTY ALARM METHODS: LED, BUZZER, TTL SIGNAL
l DIMENSION：43*422*340 (H*W*D)mm
l COOLING: TWO 38*28mm DC FAN (MODULE)
l AC INLET IN EACH MODULE
l EMI NOISE FILTER: FCC CLASS B , CISPR 22 CLASS B
l MEET IEC-1000-3-2 CLASS D (ACTIVE PFC)
l SAFETY：MEET UL1950,CSA22.2NO/950,TUV IEC950
INPUT CHARACTERISTICS: M1W4-5G20P3V
l VOLTAGE： 90∼264VAC FULL RANGE
l FREQUENCY： 47∼63HZ
l INPUT CURRENT (PER POWER MODULE)：10/5A FOR 115/230VAC
l INRUSH CURRENT (PER POWER MODULE)：160/180A MAX. FOR 115/230VAC (25℃)
OUTPUT CHARACTERISTICS:
OUTPUT CURRENT REGULATION OUTPUT OUTPUT
VOLTAGE
MIN. MAX. LOAD LINE RIPPLE & NOISE
MAX. [P-P]
+5V 4A 85A
+12V 8A 115A
-12V 0A 2A
+3.3V 4A 65A
+5VSB 0.4A 3.5A
±5% ±50mV
±5% ±50mV
±5% ±50mV
±5% ±50mV
±5% ±50mV
50mV
70mV
70mV
50mV
50mV
REMARKS:
27. TOTAL MAX OUTPUT OF +5V AND +3.3V NOT EXCEED 560W.
28. POWER MODULE TOTAL OUTPUT POWER NOT EXCEED 1620W.
SPECIFICATION:
l TEMPERATURE RANGE：OPERATING 0℃∼40℃，STORAGE -20℃∼80℃
l HOLD UP TIME：16mS MIN.
l DIELECTRIC WITHSTAND：INPUT/OUTPUT 1500 VAC FOR 1 MINUTE
INPUT TO FRAME GROUND 1500 VAC FOR 1 MINUTE
l EFFICIENCY：65% TYPICAL，AT FULL LOAD
l POWER GOOD SIGNAL：ON DELAY 100mS TO 500mS，OFF DELAY 1mS
l OVERLOAD PROTECTION：110∼150% MAX
l OVER VOLTAGE PROTECTION：+5V→5.7V∼6.5V，+3.3V→3.7V∼4.3V ，
+12V→13.3 V∼15V
l OVER CURRENT PROTECTION: +5V,+12V,+3.3V 110~ 150% AT FULL LOAD
l REMOTE ON / OFF CONTROL
l REMOTE SENSING DESIGN
l BALANCE LOAD SHARING DESIGN
l HOT-SWAPPABLE/HOT PLUGGABLE REDUNDANCY FUNCTION
l ISOLATION: BUILT-IN THE POWER MODULE
l FAULTY ALARM METHODS: LED, BUZZER, TTL SIGNAL
l DIMENSION：166*101*300 (H*W*D)mm
l COOLING: TWO 38*28mm DC FAN (MODULE)
l AC INLET IN EACH MODULE
l EMI NOISE FILTER: FCC CLASS B , CISPR 22 CLASS B
l MEET IEC-1000-3-2 CLASS D (ACTIVE PFC)
l SAFETY：MEET UL1950,CSA22.2NO/950,TUV IEC950
INPUT CHARACTERISTICS: M1W4-5K40P3H
l VOLTAGE：90∼264VAC FULL RANGE
l FREQUENCY：47∼63HZ
l INPUT CURRENT (PER POWER MODULE)：10/5A FOR 115/230VAC
l INRUSH CURRENT (PER POWER MODULE)：190/210A MAX. FOR 115/230VAC (25℃)
OUTPUT CHARACTERISTICS:
OUTPUT CURRENT REGULATION OUTPUT OUTPUT
VOLTAGE
MIN. MAX. LOAD LINE RIPPLE & NOISE
MAX. [P-P]
+5V 4A 110A
+12V 8A 150A
-12V 0A 2.5A
+3.3V 4A 80A
+5VSB 0.4A 4A
±5% ±50mV
±5% ±50mV
±5% ±50mV
±5% ±50mV
±5% ±50mV
50mV
70mV
70mV
50mV
50mV
REMARKS:
29. TOTAL MAX OUTPUT OF +5V AND +3.3V NOT EXCEED 710W.
30. POWER MODULE TOTAL OUTPUT POWER NOT EXCEED 2040W.
SPECIFICATION:
l TEMPERATURE RANGE：OPERATING 0℃∼40℃，STORAGE -20℃∼80℃
l HOLD UP TIME：16mS MIN.
l DIELECTRIC WITHSTAND：INPUT/OUTPUT 1500 VAC FOR 1 MINUTE
INPUT TO FRAME GROUND 1500 VAC FOR 1 MINUTE
l 4、EFFICIENCY：65% TYPICAL，AT FULL LOAD
l 5、POWER GOOD SIGNAL：ON DELAY 100mS TO 500mS，OFF DELAY 1mS
l 6、OVERLOAD PROTECTION：110∼150% MAX
l 7、OVER VOLTAGE PROTECTION：+5V→5.7V∼6.5V，+3.3V→3.7V∼4.3V ，+12V→13.3 V∼
15V
l 8、OVER CURRENT PROTECTION: +5V,+12V,+3.3V 110~ 150% AT FULL LOAD
l 11、REMOTE ON / OFF CONTROL
l 10、REMOTE SENSING DESIGN
l 11、BALANCE LOAD SHARING DESIGN
l HOT-SWAPPABLE/HOT PLUGGABLE REDUNDANCY FUNCTION
l ISOLATION: BUILT-IN THE POWER MODULE
l FAULTY ALARM METHODS: LED, BUZZER, TTL SIGNAL
l DIMENSION：43*422*340(H*W*D)mm
l COOLING: TWO 38*28mm DC FAN (MODULE)
l AC INLET IN EACH MODULE
l EMI NOISE FILTER: FCC CLASS B , CISPR 22 CLASS B
l MEET IEC-1000-3-2 CLASS D (ACTIVE PFC)
l SAFETY：MEET UL1950,CSA22.2NO/950,TUV IEC950
INPUT CHARACTERISTICS: M1W4-5K40P3V
l VOLTAGE：90∼264VAC FULL RANGE
l FREQUENCY：47∼63HZ
l INPUT CURRENT (PER POWER MODULE)：10/5A FOR 115/230VAC
l INRUSH CURRENT (PER POWER MODULE)：190/210A MAX. FOR 115/230VAC (25℃)
OUTPUT CHARACTERISTICS:
OUTPUT CURRENT REGULATION OUTPUT OUTPUT
VOLTAGE
MIN. MAX. LOAD LINE RIPPLE & NOISE
MAX. [P-P]
+5V 4A 110A
+12V 8A 150A
-12V 0A 2.5A
+3.3V 4A 80A
+5VSB 0.4A 4A
±5% ±50mV
±5% ±50mV
±5% ±50mV
±5% ±50mV
±5% ±50mV
50mV
70mV
70mV
50mV
50mV
REMARKS:
31. TOTAL MAX OUTPUT OF +5V AND +3.3V NOT EXCEED 710W.
32. POWER MODULE TOTAL OUTPUT POWER NOT EXCEED 2040W.
SPECIFICATION:
l TEMPERATURE RANGE：OPERATING 0℃∼40℃，STORAGE -20℃∼80℃
l HOLD UP TIME：16mS MIN.
l DIELECTRIC WITHSTAND：INPUT/OUTPUT 1500 VAC FOR 1 MINUTE
INPUT TO FRAME GROUND 1500 VAC FOR 1 MINUTE
l EFFICIENCY：65% TYPICAL，AT FULL LOAD
l POWER GOOD SIGNAL：ON DELAY 100mS TO 500mS，OFF DELAY 1mS
l OVERLOAD PROTECTION：110∼150% MAX
l OVER VOLTAGE PROTECTION：+5V→5.7V∼6.5V，+3.3V→3.7V∼4.3V ，
+12V→13.3 V∼15V
l OVER CURRENT PROTECTION: +5V,+12V,+3.3V 110~ 150% AT FULL LOAD
l REMOTE ON / OFF CONTROL
l REMOTE SENSING DESIGN
l BALANCE LOAD SHARING DESIGN
l HOT-SWAPPABLE/HOT PLUGGABLE REDUNDANCY FUNCTION
l ISOLATION: BUILT-IN THE POWER MODULE
l FAULTY ALARM METHODS: LED, BUZZER, TTL SIGNAL
l DIMENSION：166*101*300(H*W*D)mm
l COOLING: TWO 38*28mm DC FAN (MODULE)
l AC INLET IN EACH MODULE
l EMI NOISE FILTER: FCC CLASS B , CISPR 22 CLASS B
l MEET IEC-1000-3-2 CLASS D (ACTIVE PFC)
l SAFETY：MEET UL1950,CSA22.2NO/950,TUV IEC950
INPUT CHARACTERISTICS: M2W-6460P
l VOLTAGE: 100~240VAC FULL RANGE
l FREQUENCY:47~63HZ
l INPUT CURRENT: 4A ( RMS ) FOR 230VAC
l 8A ( RMS ) FOR 115VAC
l INRUSH CURRENT : 60 A MAX.FOR 115 VAC PER MODULE
l 80 A MAX. FOR 230 VAC PER MODULE
OUTPUT CHARACTERISTICS:
OUTPUT
VOLTAGE
OUTPUT CURRENT REGULATION OUTPUT
RIPPLE & NOISE
MIN. [A] MAX. [A] LOAD LINE
+5V 3.5 30 ±
-5V 0.05 0.7
5%
5/-10%
±
+12V 2 32 +6%
-12V 0.05 0.7 +5/-10%
+3.3V 1 24
+5VSB 0.1 2.0
5%
±
5/-6%
±
±
±
±
±
±
±
1%
1%
1%
1%
1%
1%
REMARKS: 1.TOTAL CURRENT OF +5V AND +3.3V NOT EXCEED 40A
2.TOTAL OUTPUT POWER NOT EXCEED 460W
SPECIFICATION:
MAX. [P-P]
70mV
120mV
120mV
120mV
70mV
70mV
l TEMPERATURE RANGE: OPERATING 0℃ --- 40℃,STORAGE -20℃ --- 70℃
l HOLD UP TIME: 1.6 ms MINIMUM AT FULL LOAD & 90VAC INPUT VOLTAGE
l DIELECTRIC WITHSTAND: INPUT / OUTPUT 1500 VAC FOR 1 MINUTE
INPUT TO FRAME GROUND 3000 VAC FOR 1 MINUTE
l EFFICIENCY: 65% TYPICAL, AT FULL LOAD
l POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms
l OVER LOAD PROTECTION: 110~180% MAX
. OVER VOLTAGE PROTECTION: +5V à 5.7V ~ 6.5V, +3.3V à3.9V~4.7V,+12V à 13.3V ~ 14.3V
. OVER CURRENT PROTECTION
l EMI NOISE FILTER: FCC CLASS B, CISPR22 CLASS B
l SAFETY: UL 1950, CSA 22.2 NO/ 950, TÜV IEC 950
l REMOTE ON / OFF CONTROL
l FAULTY ALARM METHODS:LED, BUZZER, TTL SIGNAL
l MEET IEC-1000-3-2 CLASS D ( ACTIVE PFC)
l HOT-SWAPPABLE/HOT PLUGGABLE REDUNDANCY FUNCTION
l REMOTE SENSING DESIGN
l ISOLATION:BUILT-IN THE POWER MODULE
l COOLING: TWO 38x38x28mm DC FANS
INPUT CHARACTERISTICS: M2W-6500P
l VOLTAGE: 100V ~ 240VAC
l FREQUENCY: 47~ 63HZ
l INPUT CURRENT: 4A ( RMS ) FOR 230VAC
8A ( RMS ) FOR 115VAC
l INRUSH CURRENT : 60 A MAX.FOR 115 VAC PER MODULE
80 A MAX. FOR 230 VAC PER MODULE
OUTPUT CHARACTERISTICS:
OUTPUT
VOLTAGE
OUTPUT CURRENT REGULATION OUTPUT
RIPPLE & NOISE
MIN. [A] MAX. [A] LOAD LINE
+5V 3.5 30 ±
-5V 0.05 0.7
5%
5/-10%
±
+12V 2 32 +6%
-12V 0.05 0.7 +5/-10%
+3.3V 1 24
+5VSB 0.1 2.0
5%
±
5/-6%
±
±
±
±
±
±
±
1%
1%
1%
1%
1%
1%
REMARKS: 1.TOTAL CURRENT OF +5V AND +3.3V NOT EXCEED 40A
2.TOTAL OUTPUT POWER NOT EXCEED 500W
SPECIFICATION:
MAX. [P-P]
70mV
120mV
120mV
120mV
70mV
70mV
l TEMPERATURE RANGE: OPERATING 0℃ --- 40℃,STORAGE -20℃ --- 70℃
l HOLD UP TIME: 1.6 ms MINIMUM AT FULL LOAD & 90VAC INPUT VOLTAGE
l DIELECTRIC WITHSTAND: INPUT / OUTPUT 3000 VAC FOR 1 MINUTE
INPUT TO FRAME GROUND 1500 VAC FOR 1 MINUTE
l EFFICIENCY: 65% TYPICAL, AT FULL LOAD
l POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms
l OVER LOAD PROTECTION: 110~180% MAX
. OVER VOLTAGE PROTECTION: +5V à 5.7V ~ 6.5V, +3.3V à 3.9V~4.7V, +12V à 13.3V ~
14.3V
. OVER CURRENT PROTECTION
l EMI NOISE FILTER: FCC CLASS B, CISPR22 CLASS B
l SAFETY: UL 1950, CSA 22.2 NO/ 950, TÜV IEC 950
l REMOTE ON / OFF CONTROL
l FAULTY ALARM METHODS: LED, BUZZER, TTL SIGNAL
l MEET IEC-1000-3-2 CLASS D (ACTIVE PFC)
l HOT-SWAPPABLE/HOT PLUGGABLE REDUNDANCY FUNCTION
l REMOTE SENSING DESIGN
l ISOLATION: BUILT-IN THE POWER MODULE
l COOLING: TWO 38x38x28mm DC FANS
l AC INLET IN EACH MODULE
INPUT CHARACTERISTICS: M2W-6550P
l VOLTAGE: 100V ~ 240VAC
l FREQUENCY: 47~ 63HZ
l INPUT CURRENT: 4A ( RMS ) FOR 230VAC
8A ( RMS ) FOR 115VAC
l INRUSH CURRENT: 60 A MAX.FOR 115 VAC PER MODULE
80 A MAX. FOR 230 VAC PER MODULE
OUTPUT CHARACTERISTICS:
OUTPUT
VOLTAGE
OUTPUT CURRENT REGULATION OUTPUT
RIPPLE & NOISE
MIN. [A] MAX. [A] LOAD LINE
+5V 3.5 30 ±
-5V 0.05 0.7
5%
5/-10%
±
+12V 2 36 +6%
-12V 0.05 0.7 +5/-10%
+3.3V 1 24
+5VSB 0.1 2.0
5%
±
5/-6%
±
±
±
±
±
±
±
1%
1%
1%
1%
1%
1%
REMARKS: 1.TOTAL CURRENT OF +5V AND +3.3V NOT EXCEED 40A
2.TOTAL OUTPUT POWER NOT EXCEED 550W
SPECIFICATION:
MAX. [P-P]
70mV
120mV
120mV
120mV
70mV
70mV
l TEMPERATURE RANGE: OPERATING 0℃ --- 40℃,STORAGE -20℃ --- 70℃
l HOLD UP TIME: 1.6 ms MINIMUM AT FULL LOAD & 90VAC INPUT VOLTAGE
l DIELECTRIC WITHSTAND: INPUT / OUTPUT 3000 VAC FOR 1 MINUTE
INPUT TO FRAME GROUND 1500 VAC FOR 1 MINUTE
l EFFICIENCY: 65% TYPICAL, AT FULL LOAD
l POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms
l OVER LOAD PROTECTION: 110~180% MAX
. OVER VOLTAGE PROTECTION: +5V à 5.7V ~ 6.5V, +3.3V à 3.9V~4.7V, +12V à 13.3V ~
14.3V
. OVER CURRENT PROTECTION
l EMI NOISE FILTER: FCC CLASS B, CISPR22 CLASS B
l SAFETY: UL 1950, CSA 22.2 NO/ 950, TÜV IEC 950
l REMOTE ON / OFF CONTROL
l FAULTY ALARM METHODS: LED, BUZZER, TTL SIGNAL
l MEET IEC-1000-3-2 CLASS D (ACTIVE PFC)
l HOT-SWAPPABLE/HOT PLUGGABLE REDUNDANCY FUNCTION
l REMOTE SENSING DESIGN
l ISOLATION: BUILT-IN THE POWER MODULE
l COOLING: TWO 38x38x28mm DC FANS
l AC INLET IN EACH MODULE
INPUT CHARACTERISTICS: M3W-6500P
l VOLTAGE: 100V ~ 240VAC
l FREQUENCY: 47Hz ~ 63Hz
l INPUT CURRENT: 20-10A MAX AT ANY LOW/HIGH INPUT VOLTAGE
l INRUSH CURRENT: 60/100A @ 115/230VAC (25℃)
l POWER FACTOR CORRECTION: 95% @ 110V, FULL LOAD
OUTPUT CHARACTERISTICS:
OUTPUT
VOLTAGE
OUTPUT CURRENT REGULATION OUTPUT
MIN. [A] MAX. [A] LOAD LINE
5V 3.5 30 ± 5% ± 50mV 70mV
12V 2.0 32 ± 6% ± 50mV 120mV
-5V 0.05 0.7 +5%, -10% ± 50mV 120mV
-12V 0.1 0.7 +5%, -10% ± 50mV 120mV
3.3V 1.0 24 ± 5% ± 50mV 70mV
+5VSB 0.1 2.0 +5%, -6% ± 50mV 70mV
REMARKS:
1. THE OUTPUT POWER OF 5V & 3.3V MAX: 40A
2. EACH POWER MODULE OUTPUT MAX: 500W
3. TOTAL OUTPUT POWER MAX: 500W
4. 2 MODULE AND PLUS 1 DUMMY
SPECIFICATION:
l TEMPERATURE RANGE: OPERATING: 0℃ --- 40℃
RIPPLE & NOISE
MAX. [P-P]
STORAGE: -20℃ --- 80℃
l HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE
l DIELECTRIC WITHSTAND: INPUT / OUTPUT 3000 VAC FOR 1 SECOND
INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND
l EFFICIENCY: 65% TYPICAL AT 115VAC FULL LOAD
l POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms
l OVER POWER PROTECTION: 110% ~ 180%
OVER VOLTAGE PROTECTION: +5V à 5.7V ~ 6.5V, 3.3V à 3.9V ~ 4.7V
+12V à 13.3V ~ 14.3V
OVER CURRENT PROTECTION: 110% ~ 180%
l SHORT CIRCUIT PROTECTION: +5V, -5V, +12V, -12V, +3.3V
l EMI NOISE FILTER: FCC CLASS A, CISPR22 CLASS A
l SAFETY: UL 1950, CSA 22.2 NO/ 950, TÜV IEC 950
l REMOTE ON / OFF CONTROL
THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE /
ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),
AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,
AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABLE.
l 3.3V REMOTE SENSING
l DIMENSION: 300 (D) x 101 (W) x 125 (H) mm
INPUT CHARACTERISTICS: M3W-6950P
l VOLTAGE: 100V ~ 240VAC
l FREQUENCY: 47Hz ~ 63Hz
l INPUT CURRENT: 20-10A MAX AT ANY LOW/HIGH INPUT VOLTAGE
l INRUSH CURRENT: 60/100A @ 115/230VAC (25℃)
l POWER FACTOR CORRECTION: 95% @ 110V, FULL LOAD
OUTPUT CHARACTERISTICS:
OUTPUT
VOLTAGE
OUTPUT CURRENT REGULATION OUTPUT
MIN. [A] MAX. [A] LOAD LINE
RIPPLE & NOISE
MAX. [P-P]
5V 6.0 56 ± 5% ± 50mV 70mV
12V 6.0 60 ± 6% ± 50mV 120mV
-5V 0.2 1.2 +5%, -10% ± 50mV 120mV
-12V 0.2 1.2 +5%, -10% ± 50mV 120mV
3.3V 3.5 44 ± 5% ± 50mV 70mV
+5VSB 0.4 3.5 +5%, -6% ± 50mV 70mV
REMARKS:
2. THE OUTPUT POWER OF 5V & 3.3V MAX: 40A
2. EACH POWER MODULE OUTPUT MAX: 500W
3. TOTAL OUTPUT POWER MAX: 950W
SPECIFICATION:
l TEMPERATURE RANGE: OPERATING: 0℃ --- 40℃
STORAGE: -20℃ --- 80℃
l HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE
l DIELECTRIC WITHSTAND: INPUT / OUTPUT 3000 VAC FOR 1 SECOND
INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND
l EFFICIENCY: 65% TYPICAL AT 115VAC FULL LOAD
l POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms
l OVER POWER PROTECTION: 110% ~ 180%
OVER VOLTAGE PROTECTION: +5V à 5.7V ~ 6.5V, 3.3V à 3.9V ~ 4.7V
+12V à 13.3V ~ 14.3V
OVER CURRENT PROTECTION: 110% ~ 180%
l SHORT CIRCUIT PROTECTION: +5V, -5V, +12V, -12V, +3.3V
l EMI NOISE FILTER: FCC CLASS A, CISPR22 CLASS A
l SAFETY: UL 1950, CSA 22.2 NO/ 950, TÜV IEC 950
l REMOTE ON / OFF CONTROL
THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE /
ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),
AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,
AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABLE.
l 3.3V REMOTE SENSING
l DIMENSION: 300 (D) x 101 (W) x 125 (H) mm
INPUT CHARACTERISTICS: M3W-6D50P
l VOLTAGE: 100V ~ 240VAC
l FREQUENCY: 47Hz ~ 63Hz
l INPUT CURRENT: 20-10A MAX AT ANY LOW/HIGH INPUT VOLTAGE
l INRUSH CURRENT: 60/100A @ 115/230VAC (25℃)
l POWER FACTOR CORRECTION: 95% @ 110V, FULL LOAD
OUTPUT CHARACTERISTICS:
OUTPUT
VOLTAGE
OUTPUT CURRENT REGULATION OUTPUT
MIN. [A] MAX. [A] LOAD LINE
RIPPLE & NOISE
MAX. [P-P]
5V 6.0 94.5 ± 5% ± 50mV 70mV
12V 6.0 90 ± 6% ± 50mV 120mV
-5V 0.2 1.2 +5%, -10% ± 50mV 120mV
-12V 0.2 1.2 +5%, -10% ± 50mV 120mV
3.3V 3.5 67.5 ± 5% ± 50mV 70mV
+5VSB 0.4 3.5 +5%, -6% ± 50mV 70mV
REMARKS:
3. THE OUTPUT POWER MODULE OF 5V & 3.3V MAX: 40A
2. EACH POWER MODULE OUTPUT MAX: 500W
3. TOTAL OUTPUT POWER MAX: 1350W
SPECIFICATION:
l TEMPERATURE RANGE: OPERATING: 0℃ --- 40℃
STORAGE: -20℃ --- 80℃
l HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE
l DIELECTRIC WITHSTAND: INPUT / OUTPUT 3000 VAC FOR 1 SECOND
INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND
l EFFICIENCY: 65% TYPICAL AT 115VAC FULL LOAD
l POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms
l OVER POWER PROTECTION: 110% ~ 180%
OVER VOLTAGE PROTECTION: +5V à 5.7V ~ 6.5V, 3.3V à 3.9V ~ 4.7V
+12V à 13.3V ~ 14.3V
OVER CURRENT PROTECTION: 110% ~ 180%
l SHORT CIRCUIT PROTECTION: +5V, -5V, +12V, -12V, +3.3V
l EMI NOISE FILTER: FCC CLASS A, CISPR22 CLASS A
l SAFETY: UL 1950, CSA 22.2 NO/ 950, TÜV IEC 950
l REMOTE ON / OFF CONTROL
THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE /
ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),
AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,
AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABLE.
l 3.3V REMOTE SENSING
l DIMENSION: 300 (D) x 101 (W) x 125 (H) mm
INPUT CHARACTERISTICS: M4W-6500P
l VOLTAGE: 100V ~ 240VAC
l FREQUENCY: 47Hz ~ 63Hz
l INPUT CURRENT: 20-10A MAX AT ANY LOW/HIGH INPUT VOLTAGE
l INRUSH CURRENT: 60/100A @ 115/230VAC (25℃)
l POWER FACTOR CORRECTION: 95% @ 110V, FULL LOAD
OUTPUT CHARACTERISTICS:
OUTPUT
VOLTAGE
OUTPUT CURRENT REGULATION OUTPUT
MIN. [A] MAX. [A] LOAD LINE
RIPPLE & NOISE
MAX. [P-P]
5V 3.5 30 ± 5% ± 50mV 70mV
12V 2.0 32 ± 6% ± 50mV 120mV
-5V 0.05 0.7 +5%, -10% ± 50mV 120mV
-12V 0.1 0.7 +5%, -10% ± 50mV 120mV
3.3V 1.0 24 ± 5% ± 50mV 70mV
+5VSB 0.1 2.0 +5%, -6% ± 50mV 70mV
REMARKS:
33. THE OUTPUT POWER OF 5V & 3.3V MAX: 40A
34. EACH POWER MODULE OUTPUT MAX: 500W
35. TOTAL OUTPUT POWER MAX: 500W
36. 2 MODULE AND PLUS 2 DUMMY
SPECIFICATION:
l TEMPERATURE RANGE: OPERATING: 0℃ --- 40℃
STORAGE: -20℃ --- 80℃
l HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE
l DIELECTRIC WITHSTAND: INPUT / OUTPUT 3000 VAC FOR 1 SECOND
INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND
l EFFICIENCY: 67% TYPICAL AT 115VAC FULL LOAD
l POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms
l OVER POWER PROTECTION: 110% ~ 180%
OVER VOLTAGE PROTECTION: +5V à 5.7V ~ 6.5V, 3.3V à 3.9V ~ 4.7V
+12V à 13.3V ~ 14.3V
OVER CURRENT PROTECTION: 110% ~ 180%
l SHORT CIRCUIT PROTECTION: +5V, -5V, +12V, -12V, +3.3V
l EMI NOISE FILTER: FCC CLASS A, CISPR22 CLASS A
l SAFETY: UL 1950, CSA 22.2 NO/ 950, TÜV IEC 950
l REMOTE ON / OFF CONTROL
THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE /
ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),
AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,
AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABL
l 3.3V REMOTE SENSING
l DIMENSION: 300 (D) x101 (W) x 166 (H) mm
INPUT CHARACTERISTICS: M4W-6950P
l VOLTAGE: 100V ~ 240VAC
l FREQUENCY: 47Hz ~ 63Hz
l INPUT CURRENT: 20-10A MAX AT ANY LOW/HIGH INPUT VOLTAGE
l INRUSH CURRENT: 60/100A @ 115/230VAC (25℃)
l POWER FACTOR CORRECTION: 95% @ 110V, FULL LOAD
OUTPUT CHARACTERISTICS:
OUTPUT
VOLTAGE
OUTPUT CURRENT REGULATION OUTPUT
MIN. [A] MAX. [A] LOAD LINE
RIPPLE & NOISE
MAX. [P-P]
5V 6.0 56 ± 5% ± 50mV 70mV
12V 6.0 60 ± 6% ± 50mV 120mV
-5V 0.2 1.2 +5%, -10% ± 50mV 120mV
-12V 0.2 1.2 +5%, -10% ± 50mV 120mV
3.3V 3.5 44 ± 5% ± 50mV 70mV
+5VSB 0.4 3.5 +5%, -6% ± 50mV 70mV
REMARKS:
37. THE OUTPUT POWER OF 5V & 3.3V MAX: 40A
38. EACH POWER MODULE OUTPUT MAX: 500W
39. TOTAL OUTPUT POWER MAX: 950W
40. 2 MODULE AND PLUS 1 DUMMY
SPECIFICATION:
l TEMPERATURE RANGE: OPERATING: 0℃ --- 40℃
STORAGE: -20℃ --- 80℃
l HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE
l DIELECTRIC WITHSTAND: INPUT / OUTPUT 3000 VAC FOR 1 SECOND
INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND
l EFFICIENCY: 67% TYPICAL AT 115VAC FULL LOAD
l POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms
l OVER POWER PROTECTION: 110% ~ 180%
OVER VOLTAGE PROTECTION: +5V à 5.7V ~ 6.5V, 3.3V à 3.9V ~ 4.7V
+12V à 13.3V ~ 14.3V
OVER CURRENT PROTECTION: 110% ~ 180%
l SHORT CIRCUIT PROTECTION: +5V, -5V, +12V, -12V, +3.3V
l EMI NOISE FILTER: FCC CLASS A, CISPR22 CLASS A
l SAFETY: UL 1950, CSA 22.2 NO/ 950, TÜV IEC 950
l REMOTE ON / OFF CONTROL
THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE /
ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),
AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,
AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABL
l 3.3V REMOTE SENSING
l DIMENSION: 300 (D) x101 (W) x 166 (H) mm
INPUT CHARACTERISTICS: M4W-6D50P
l VOLTAGE: 100V ~ 240VAC
l FREQUENCY: 47Hz ~ 63Hz
l INPUT CURRENT: 20-10A MAX AT ANY LOW/HIGH INPUT VOLTAGE
l INRUSH CURRENT: 60/100A @ 115/230VAC (25℃)
l POWER FACTOR CORRECTION: 95% @ 110V, FULL LOAD
OUTPUT CHARACTERISTICS:
OUTPUT
VOLTAGE
OUTPUT CURRENT REGULATION OUTPUT
MIN. [A] MAX. [A] LOAD LINE
RIPPLE & NOISE
MAX. [P-P]
5V 6.0 84.5 ± 5% ± 50mV 70mV
12V 6.0 90 ± 6% ± 50mV 120mV
-5V 0.2 1.2 +5%, -10% ± 50mV 120mV
-12V 0.2 1.2 +5%, -10% ± 50mV 120mV
3.3V 3.5 67.5 ± 5% ± 50mV 70mV
+5VSB 0.4 3.5 +5%, -6% ± 50mV 70mV
REMARKS:
41. THE OUTPUT POWER OF 5V & 3.3V MAX: 40A
42. EACH POWER MODULE OUTPUT MAX: 500W
43. TOTAL OUTPUT POWER MAX: 1350W
SPECIFICATION:
l TEMPERATURE RANGE: OPERATING: 0℃ --- 40℃
STORAGE: -20℃ --- 80℃
l HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE
l DIELECTRIC WITHSTAND: INPUT / OUTPUT 3000 VAC FOR 1 SECOND
INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND
l EFFICIENCY: 67% TYPICAL AT 115VAC FULL LOAD
l POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms
l OVER POWER PROTECTION: 110% ~ 180%
OVER VOLTAGE PROTECTION: +5V à 5.7V ~ 6.5V, 3.3V à 3.9V ~ 4.7V
+12V à 13.3V ~ 14.3V
OVER CURRENT PROTECTION: 110% ~ 180%
l SHORT CIRCUIT PROTECTION: +5V, -5V, +12V, -12V, +3.3V
l EMI NOISE FILTER: FCC CLASS A, CISPR22 CLASS A
l SAFETY: UL 1950, CSA 22.2 NO/ 950, TÜV IEC 950
l REMOTE ON / OFF CONTROL
THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE /
ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),
AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,
AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABL
l 3.3V REMOTE SENSING
l DIMENSION: 300 (D) x101 (W) x166 (H) mm
INPUT CHARACTERISTICS: M4W-6I00P
l VOLTAGE: 100V ~ 240VAC
l FREQUENCY: 47Hz ~ 63Hz
l INPUT CURRENT: 20-10A MAX AT ANY LOW/HIGH INPUT VOLTAGE
l INRUSH CURRENT: 60/100A @ 115/230VAC (25℃)
l POWER FACTOR CORRECTION: 95% @ 110V, FULL LOAD
OUTPUT CHARACTERISTICS:
OUTPUT
VOLTAGE
OUTPUT CURRENT REGULATION OUTPUT
MIN. [A] MAX. [A] LOAD LINE
RIPPLE & NOISE
MAX. [P-P]
5V 6.0 84.5 ± 5% ± 50mV 70mV
12V 6.0 90 ± 6% ± 50mV 120mV
-5V 0.2 1.2 +5%, -10% ± 50mV 120mV
-12V 0.2 1.2 +5%, -10% ± 50mV 120mV
3.3V 3.5 67.5 ± 5% ± 50mV 70mV
+5VSB 0.4 3.5 +5%, -6% ± 50mV 70mV
REMARKS:
44. THE OUTPUT POWER OF 5V & 3.3V MAX: 40A
45. EACH POWER MODULE OUTPUT MAX: 500W
46. TOTAL OUTPUT POWER MAX: 1800W
SPECIFICATION:
l TEMPERATURE RANGE: OPERATING: 0℃ --- 40℃
STORAGE: -20℃ --- 80℃
l HOLD UP TIME: 16 ms MINIMUM AT FULL LOAD & NORMAL INPUT VOLTAGE
l DIELECTRIC WITHSTAND: INPUT / OUTPUT 3000 VAC FOR 1 SECOND
INPUT TO FRAME GROUND 1500 VAC FOR 1 SECOND
l EFFICIENCY: 67% TYPICAL AT 115VAC FULL LOAD
l POWER GOOD SIGNAL: ON DELAY 100 ms TO 500 ms, OFF DELAY 1 ms
l OVER POWER PROTECTION: 110% ~ 180%
OVER VOLTAGE PROTECTION: +5V à 5.7V ~ 6.5V, 3.3V à 3.9V ~ 4.7V
+12V à 13.3V ~ 14.3V
OVER CURRENT PROTECTION: 110% ~ 180%
l SHORT CIRCUIT PROTECTION: +5V, -5V, +12V, -12V, +3.3V
l EMI NOISE FILTER: FCC CLASS A, CISPR22 CLASS A
l SAFETY: UL 1950, CSA 22.2 NO/ 950, TÜV IEC 950
l REMOTE ON / OFF CONTROL
THE UNIT SHALL ACCEPT A LOGIC OPEN COLLECTOR LEVEL WHICH WILL DISABLE /
ENABLE ALL THE OUTPUT VOLTAGE (EXCLUDE +5V STANDBY),
AS LOGIC LEVEL IS LOW, OUTPUTS VOLTAGE WERE ENABLE,
AS LOGIC LEVEL IS HIGH, OUTPUTS VOLTAGE WERE DISABL
l 3.3V REMOTE SENSING
l DIMENSION: 300 (D) x101 (W) x166 (H) mm
1.7INSTALLATION & TESTING
Mount the power system into the system chassis
Attach the connectors to main board by following the main board’s instructions, there
are various on pinouts / connectors in both the power system and main board, they
should match each other, otherwise the connection will cause undetectable harms.
Attach all the remaining power supply connections to the various peripherals as
needed, these connectors maybe “keyed”, so there will be only one possible way to
connect them.
Before applying power source to the system, make sure these are no loose or
incorrect connections. Please check your power system is AC source version or DC
source version, to supply the correct source.
To test the redundancy function, please supply the source to the individual power
modules. If the individual power module. Operates normally, the LED on the module
lits in GREEN, and the external warning LED also lits in GREEN. Now remove the
source from one of the individual power module, the warning buzzer in the power
system will sound, and the external warning LED which displays the status of the total
power supply system will blink/RED, the individual LED indicating the power module’s
status will not light. Meanwhile the power system will continue to backup the power
output without affecting the system’s operation.
The warming buzzer will continue sounding, the user can reset the warning buzzer by
pressing the buzzer reset switch.
Turn on the power module which is turned off for testing earlier, the sound of the
warning buzzer will disappear, the external warning LED will turn GREEN again; the
LED indicating the status of power module will light again, you may test other power
module by performing the similar procedure.
1.7 Hot-swap procedures
Please refer to the following when one power module is found defective.
(1) Locate the defective power module by examining the individual LED (if LED is
without light, it indicates the power module is defective).
WARNING:
Please perform the BELOW step carefully; otherwise, it may cause shut down of the
whole system.
(2) Turn off
WARNING:
Please do not remove the defective power module until you have worn gloves to keep
from been burned. This is due to the cover of the power module is used as heat sink
for cooling. Usually, its temperature is around 50-60 degree Celsius under full load
condition.
(3) Remove the defective power module by puling out method.
WATNING:
Please put aside the power module to wait for cooling down. Keep other people from
toughing it until it is cooled.
(4) Replace a new / GOOD power module, insert the power module into the power
system till to the end.
(5) Turn on the new power module.
(6) Check the LED of the power module light GREEN.
(7) Check the LED which indicates the total power system status, that SHOULD be
from blink/RED to GREEN.
(8) If you want to test this new power module and simulate the defective situation,
please refer to Section 1.7 Installation & Testing Section.
1.8 PINOUTS AND FUNCTION OF THE CONNECTORS
A. Power module defective signal:
PIN# VOLTAGE SPECIFICATION
1 GND
2 TTL SIGNAL pull up to +5Vsb
Low Active --- Defective
High --- Normal
B. Power status LED:
PIN# VOLTAGE SPECIFICATION
1 GND
2 12V Resistance 1K ohm to +12V
Low Active(blink) --- Defective
High (Green) --- Normal
C. Buzzer reset switch:
PIN# VOLTAGE SPECIFICATION
2 GND
1 5V pull up to +5Vsb
Low Active --- on shoot trigger
TTL signal:
Sink current max. 5mA
Source current max. 50uA
Low Active ---Defective
High ---Normal
1.9 TROUBLE SHOOTING
If you have followed all directions correctly, these should be no problem. Some
common symptoms are: the system doesn’t work, buzzer sound, work for a very short
period etc., please try the following steps to verify and correct it:
1. Check all the connections (correct pinouts, loose connection, wrong direction etc.,)
2. Check for short-circuit or defective peripherals by unhooking each peripheral once
at a time. When the system functions again, you have solved the problem.
3. Once you hear the buzzer sound or see the LED is blinking/ RED, please aware of:
a. If the source is OK.
b. If the load is under the minimum / over. The maximum load of each channel
(please refer the Specification)
c. If Ac / Dc input voltage been selected correctly.
d. If the power cable(s) been well plugged into the Input kit.
Suppose the above condition been happened, please turn off the power system,
await for 2-3 minutes for releasing the protection state, then test it again.
e. If buzzer still sound or the LED shows power module is defective, please
locate which power module is defective, perform Hot-swap procedure at your
proper time, send the defective item to your vendor for RMA operation.
f. If you can not fix the problem, please contact with your vendor for supporting.
The description stated herein is subject to change without prior notice.
All brand names and trademarks are the property of their respective owners.
Loading...