INSTRUCTION MANUAL
ASSEMBLY GUIDE
Congratulations, you are now the owner of the new chair!
Before enjoying the comfortable chair, you have to assemble it . This assembly guide
will take you through the basic assembly process. To make sure your assembly
progress goes smoothly, please follow the assembly instructions especially the
important safety information.
It is possible to assemble the chair by your own, while having a second person to
help you will make it easier.
Please check if there are any missing parts in the package before start. If there are
any issues, please don't hesitate to drop us an email and we'll help you ASAP.
If you run into any difficulty during the assembly, remember to check out the assembly
Video to see if you've missed something. If you're still unable to resolve your problems
, drop us an email and our support team will assist you.
WARNING
To ensure proper assembly, please follow all steps and use all parts. Failure to
follow this warning can result in serious injury to yourself or others.
2
Package List
Without further ado, we kindly suggest you to list all parts needed
for the chair first.
(1)*1 (2)*1 (3)*2
Back
Support
(4)*1 (5)*1 (6)*5
Mechanism
(7)*1 (8)*5 (9)*1
Base Headrest BracketLegs
(10)*1 (11)*10 (12)*4
Headrest Bolts Bolts
Seat Cushion
Gas Lift Casters
Armrest
(13)*8 (14)*1 (15)*8
Bolts
(16)*1
Wrench
Bolt Caps
3
Assembly Instruction
Step 1:
Turn the Base (7) upside down,
and then insert the Legs (8) one
by one into the Base.
(11)×2
1
Next, screw ten Bolts (11) into
the pre-drilled holes with the
Wrench (16) to attach the base
and the legs.
(8)
2
(5)
(6)
(7)
Step 2:
Press the Casters (6) into the holes
at the end of each Base Leg. And
then insert the Gas Lift (5) to the
base.
4
Step 3:
Align the Mechanism (4) over
the pre-drilled holes underneath
the Seat Cushion (2), make sure
the front of the mechanism is
facing the front of the Seat.
Attach the Mechanism to the Seat
Cushion using Four Bolts (12),
tighten all the bolts with the
Wrench (16), being careful not to
miss-thread the bolts or damaged
the seat.
3
(12)×4
(4)
(2)
4
(3)
50 %
(13)
Note 1: The "Front" mark on the Armrests and the "Front" mark on the
Seat Cushion should be in the same direction.
Note 2: Armrests are labeled with an "L" (left) or "R" (right) to show which
side they should be placed on.
(2)
Step 4:
Turn the Seat Cushion (2) upright
and align the center hole of the
Seat Plate over the lift, then push
the Seat Cushion down onto the
lift firmly until the connection is
secure.
Attach the Armrest (3) to the Seat
Cushion (2) with Two Bolts (13),
using the Wrench (16).
5
5
Step 5:
Lay the Back Cushion on
the seat of the chair with the
top of the cushion toward
the front.
Attach the Back Cushion (1)
to the Arms by inserting one
Bolt (13) in the Lower holes
with the Wrench (16).
6
110000%%
(1)
5
50 %
(13)
(13)
(9)
1100 00%%
(14)
Step 6:
Rotate the back of the chair up, then secure it with the Bolts (13)
use the Wrench (16). Adjust the balance on each side of the chair,
and fully tighten all the bolts at this step.
Fix the Headrest Bracket (9) behind back support by attaching the
Bolt (14).
6
6
Step 7:
Press the Headrest (10) into the Headrest Bracket firmly.
*Be cautious not to press the Headrest too hard as it will hurt your hands.
(10)
(10)
(1)
(15)
CAUTION:
Make sure all bolts and screws are fully tightened before using chair.
Lubricate all moving parts and tighten all bolts/screws every 6 month
or whenever needed.
7
6
7
Instructions For Use
1. Seat Height: Paddle-shaped lever on the right side
To raise:
While taking your weight off chair,
lift lever up.
To lower:
While seated, lift lever up.
* At the proper height, your feet should rest flat on the floor.
2. Tilt Tension: Long stem under the seat with knob
To increase tension:
+
While seated, turn knob forward
(Counter clockwise).
To decrease tension:
While seated, turn knob
-
backward (Clockwise ).
* Set the tilt tension to control the resistance you feel when leaning back.
7
8
3. Operating the tilt lockout
To let your chair tilt back, pull the
control handle out.
To stop your chair from tilting, sit
forward, then push the control
handle in.
7
9
Safety And Maintenance
Do not stand on the chair, Do Not use the chair as a stepladder.
Use this product for seating one person at a time.
Do not use the chair unless all bolts and screws are firmly secured.
Avoid contact with sharp objects to prevent puncturing the fabric.
Every 6 months, check all bolts and screws to ensure they are tight.
To clean, spot clean only using a damp towel and mild cleaner, first
test on a small, unseen area of fabric.
Chair weight limit not to exceed 250 lbs.
Safety Information
Sit in the center of the
chair,with your back to
the backrest
Do not push the chair
around when a person
is sitting in it
Do not sit at the front
edge of the chair
Do not push down on
the backrest when a
person is reclined
Do not stand on the
chair
Do not place all your
weight on only the
Do not use the chair
with more than one
backrest
person
9
10
Limited Warranty
The producer promises to repair or replace any chair that is found to be
defective in material or workmanship within one(1) and year from the date
of original purchase so long as you, the original purchaser, still owns it.
This is your sole and exclusive remedy. This warranty is subject to the
provisions below.
EXCLUSIONS:
This warranty does not apply and no other warranty applies to:
Normal wear and tear, which are to be expected over the course of
ownership.
Misuse, abuse, or excessive use of the product.
Modifications or attachments to the product that are not approved
by the manufacturer.
Products that were not installed, used or maintained in accordance
with product instructions and warnings.
Products used for rental or commercial purposes.
Damage caused by the carrier in-transit is handled under separate terms.
SEATING USAGE:
Normal use for seating is identified as the equivalent of a single shift,
forty- (40) hour workweek. To the extent that a seating product is used
in a manner exceeding this, the applicable warranty period will be
reduced in a pro-rata manner.
Some retailers might have custom models imported directly from the
factory and therefore are not supported by our local service team
because we don’t have the correct parts, please contact your retailer
directly for support. If you have any questions about that we will be
happy to assist and identify those items.
10
11
RETURN POLICY：
We adopt a 30 days return policy which means that all products purchased
on this website may be returned to us within the timeframe. You need to
contact us within 30 days after the product(s) came into your possession
and the product(s) must be returned to us without any undue delays.
Returned products must be returned in the same condition as they were
sent and they must be sent in its original packaging.
If the product is not faulty, (i.e. if you changed your mind or if you are
unhappy with the product for some other reason), the cost of shipping
will all on you. And it is your responsibility that the package arrives safely
to us so we recommend that you use a courier service where it is possible
to track the shipment.
If the product is faulty when you receive it please contact us and we will
help you out (see more information under Manufacturer Warranty).
We reserve the right to give a partial refund in cases when the product(s)
is not in an unused condition, is damaged or has missing parts not due
to our error.
HOW RETURNS WORK：
Contact us through the contact form on our website and attach the invoice
to the message as proof of purchase. And please also write the reason for
the return.
We will then get back to you as soon as possible with information on where
to send the product(s).
As soon as we have received the product(s) and made an inspection we will
inform you of our decision.
If a refund is approved we will automatically credit the purchase to your
credit card or original method of payment.
If the product(s) is damaged, not in its original condition or missing parts
we will inform you if you are eligible for a partial refund. This is decided
from case to case depending on the severity of the damages or what parts
are missing.
12
Loading...