THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
‐ Unit can tip over causing severe injury or death.
‐ Anchor unit to stud in wall (if instructed to).
‐ Do Not allow children to climb on unit.
‐ Put heavy items on lower shelves or drawers.
Easy
Assembly Di�culty Meter
Tough
1
Helpful Hints
PEOPLE NEEDED FOR ASSEMBLY: 1 - 2
ESTIMATED ASSEMBLY TIME: 1 HOUR
‐ Open your item in the area you plan to keep it to avoid excessive heavy lifting.
‐ Identify, sort and count the parts before attempting assembly.
‐ Compression dowels are lightly tapped in with a hammer.
‐ Slides are labeled with a R (right) and L (left) for proper placement.
‐ Make sure to always face the point on the top of the Cam Lock towards the outer edge.
‐ Use all the nails provided for the back panel and spread them out equally.
‐ Back panel must be used to make sure your unit is sturdy.
‐ Do NOT use harsh chemicals or abrasive cleaners on this item.
‐ Never push, pull, or drag your furniture.
2
Before You Start
‐
‐
‐
‐
‐
Read through each step carefully and follow the proper order
Separate and count all your parts and hardware
Give yourself enough room for the assembly process
Have the following tools: Hammer
Caution: If using a power drill or power screwdriver for screwing,
pl
ease be aware to slow down and stop when screw is tight.
Failure to do so may result in stripping the screw.
3
A B C D E
Cam bolt
35×6
F
Screw
20×8
88 88 16 16 8
6
Cam lock
G H I J
Short screws
10×7 Drawer rails Hinge
28 2 2 2
K L N
Cabinet shoe
10 4 1
Handle I Handle II
A
Long screws
14×3.5
Plastic plug
Positioning pin
Φ12×8
Please
align the
triangle
arrow with
the screw.
Please rotate 45
degrees to the plus
sign
45
4
installation drawing 1
First install the drawer .
1
A B
Cam bolt Cam lock
32 32 5 4 1
1.Use A to connect No.2 board
and No.3 board respectively,
and then use B to lock and
fix A
4.Fix L in front of
plate 1 with F
F
1
F
Screw
20mm×8mm
2
F
1
1
1
2
2
2
L N
Handle I
2.Align the No. 4 board with the
slot of the two No. 2 boards
and push it in
3
A
3.Use A to connect the No. 1
board with the part installed
in the previous step, and
then use B to lock A and fix it
2
Handle II
3
2 2
3
Find out all the plates with
grooves and classify them
L
2
2
1
3
X3 X1
2
N
1
4
5
2
5
installation drawing 2
Second install the cabinet.
A
Cam bolt
C D
Long screws
8 4 4 4
14mm×3.5m
6
Plastic plug
7
Attention:
When placing D, make sure that the
round hole is aligned with the
direction of C
K
Cabinet shoe
D
C
9
8
C
11
6
9
8
7
12
11
11
10
1.Punch K into the bottom hole of plate 6 and 7
7
2.Place D into the corresponding holes of No. 8
and No. 9 boards. When placing, pay attention
to the round hole of D aligned with the socket of C
3.Punch C into the corresponding holes of plate 6
and plate 7 respectively, so that it is connected
and fixed with plate 8 and plate 9
A
6
installation drawing 3
Second install the cabinet.
Plastic plug
Φ9×9
A B
Cam bolt
8 16 2
Cam lock
K
Cabinet shoe
11
A
12
7
11
11
10
B
11
6
7
9
8
12
11
11
10
1.Use A to connect the part installed in
the previous step with plates 10, 11 and 12
During installation, it is necessary to pay
attention to the direction of holes in two
No. 11 boards facing backward, and the
direction of holes in one No. 11 board
and No. 12 board facing downward
2.Use B to lock A
7
installation drawing 4
A B
Cam bolt
8 4 4 2 8
6
Cam lock
7
C D
Long screws
14mm×3.5m
2
Plastic plug
D
13
A
D
E
E
Positioning pin
14
D
B
13
14
9
1.Insert the sheet of corresponding size
into the slot of No. 6, 7 and 9 plate
2.Place E in the corresponding holes
of plate 6, 7 and 10
3.Use A to connect plate 13 and 14 with
the part installed in the previous step,
and then use B to lock A and fix it
4.Use C to punch into the hole
corresponding to plate 7 to fix plate 13
B
1
3
A
B
C
E
8
installation drawing 5
Push the drawer into the cupboard
9
installation drawing 6
19
22
21
A B
Cam bolt Cam lock
20 20 2 2
15
A
20
B
17
D
16
18
C D
Long screws
14mm×3.5mm
1.Place D into the corresponding
hole of plate 16，17
When placing, note that the round
hole of D needs to be aligned with
the jack direction of C
C
2.Fix plate 16,17 in front of plate 18 with C
3.Connect plate 15 with plate 16，17 and
plate 18 with A, and lock plate A
with B
19
Plastic plug
21
22
20
15
17
16
18
24
23
22
Use A to connect plate 19, 20 with plate 21,
22, 23 and 24, and then use B to lock and
fix plate A
B
24
A
A
23
22
10
installation drawing 7
19
15
17
18
24
22
21
20
19
21
20
Insert the corresponding size sheet into
the slot of plate 19, 20 and 21
21
15
19
17
24
18
22
20
16
16
23
2223
22
11
installation drawing 8
A B G
3
Cam lock
2
1
Connect the upper
and lower parts
with A, and then
lock A with B
A
Short screws
10mm×7mm
Cam bolt
7 7 7 7
I
Drawer rails
I1
I1
Drawer rails
I2
I2
Press the arrow to toggle the buckle,
and then pull out the track.
G
I
It is recommended to turn it over and
install it flat on the ground
Fix I in front of
No.22 board with G
12
installation drawing 9
I
Align the slide rail of plate 26 with
the slide way and push it forward
Attention：
The slide rail should be inserted
in line with the slide way
3
1
installation drawing 10
F
Screw
20mm×8mm
Leave a little space between the cabinet door and the desktop
1 12 2 1
G
Short screws
10mm×7mm
J
Hinge
L
Handle I
F
25
F
J
25
G
1.Fix L in front of plate 25 with F
2.Fix J on the inner side of
No. 25 plate with G
The hinge can be loosened with a screwdriver
to control the gap of the door.
The hinge can be loosened with a screwdriver
to control the distance between the door and
the side plank.
1
4
installation drawing 11
C
Long screws
14mm×3.5mm
C
D
8
Plastic plug
8 4 2
G
Short screws
10mm×7mm
27
H
Comer connection
D
27
1.Place D in the hole
corresponding to
C
26
26
plate 27
When placing, pay
attention to align
the round hole of
D with the socket of C
26
27
27
26
2.Use A to punch into the
corresponding holes of the
two No. 26 plates to connect
them with the two No. 27 plates
3.Fix H on the inside
of plate 26 with G
H
h
h
G
5
1
installation drawing 12
G
Short screws
10mm×7mm
K
4 4
Cabinet shoe
26
27
27
26
Punch K into the corresponding
hole at the bottom of two 26 plates
H
G
Use G to punch into
the hole corresponding
to H to fix it with
soft roll
6
1
installation drawing 1
If you have any questions about the product,
please do not hesitate to contact customer service.
5 Star Rating
Visit your local retailer’s website,rate your purcha sed
product and leave us some feedback!
We would like to extend a big "Thank You" to all of
our customers for taking the time to assemble this
FAFA&GAGA product, and to give us your
valuable feedback.
17
Loading...