UPHOLSTERED BED IN A BOX
Page 1 of 2
HARDWARE LIST
A (2) M6 x 40mm Allen Bolts
B (8) M6 x 35mm Allen Bolts
C (10) M3.5 x 32 Wood Screws
D (8) M8 x 20mm Allen Bolts
E (4) M6 x 50 Allen Bolts
F (1) M4 x 100 Allen Wrench
G (1) M5 x 65 Allen Wrench
H (16) Flat Washers
I (16) Spring Washers
J (2) Wood Dowels
PARTS LIST
K (1) Footboard
L (2) Left Side Rails
M (2) Right Side Rails
N (2) Rail Supports
O (2) Feet
P (13) Slats
Q (2) Cross Bars
R (4) Cross Bar Supports
J
J
O
FIGURE 1
FIGURE 2
O
K
AA
K
QTYPAR T
2A 8B
10C 8D
4E 1F
1G
16I
HARDWARE QTYPAR T HARDWARE
16
H
J
2
STEP 1 - Figure 1
Begin assembly by inserting 1 Wood Dowel (J)
into each Foot (O) on the angled side. Lightly
hammer dowels to make sure they are in tightly
(hammer not included).
STEP 2 - Figure 2
Next attach Feet (O) to Footboard (K) by
inserting the dowel in the inside hole and
securing with 1 Allen Bolt (A) per foot. Tighten
bolts with Allen Wrench (F) provided.
B
B
STEP 3 - Figure 3
Line up each set of Left (L) and Right (M) Side Rails to each
other and secure them together with the Rail Supports (N) using
H
H
I
I
4 Allen Bolts (B), 4 Spring Washers (I) and 4 Flat Washers (H).
Tighten all bolts with Allen Wrench (F) provided.
FIGURE 3
L
M
L
CARE & MAINTENANCE
as they may cause damage to the finish. Periodic checks are recommended to make sure that all hardware is securely tightened.
:
The touch of a soft cloth is all the maintenance the finish will ever need. Please do not use harsh or abrasive cleaners for polishing,
N
M
M
H
H
I
I
D
D
FIGURE 4
UPHOLSTERED BED IN A BOX
K
Page 2 of 2
STEP 4 - Figure 4
Attach Side Rails (L & M) to Headboard and Footboard (K)
using 2 Allen Bolts (D), 2 Spring Washers (I) and 2 Flat
Washers (H) per side. Tighten all bolts with Allen Wrench
(G) provided.
L
CC
P
FIGURE 5
L
N
M
M
L
Q
M
E
E
STEP 5 - Figure 5
Attach center Slat (P) to Rail
Supports (N) using 1 Wood
Screw (C) per side. Tighten
screws with Phillips head
screwdriver (not included).
STEP 6 - Figure 6
Attach 2 Cross Bars (Q) to
4 Cross Bar Supports (R)
securing through Slats (P)
with Allen Bolts (E). Tighten
all bolts with Allen Wrench
(F) provided. The assembly
is now complete.
P
FIGURE 6
CARE & MAINTENANCE
as they may cause damage to the finish. Periodic checks are recommended to make sure that all hardware is securely tightened.
:
The touch of a soft cloth is all the maintenance the finish will ever need. Please do not use harsh or abrasive cleaners for polishing,
R
Loading...