INSTALLATION AND SAFETY INSTRUCTIONS
GROUP A: Connect to Black
House Wire
GROUP B: Connect to White
House Wire
BLACK
WHITE
*PARALLEL WIRE (round &
smooth)
*PARALLEL WIRE (square &
ridged)
WHITE OR GREY WITH
TRACER
WHITE OR GREY WITHOUT
TRACER
BROWN GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
FOR YOUR SAFETY WARNING
BE SURE THE ELECTRICITY TO THE WIRES YOU ARE
WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED
OR THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this fixture. Be sure to follow
the steps in the order given. Under no circumstances should a
fixture be hung on house electrical wires, nor should a swag type
fixture be installed on a ceiling, which contains a radiant type
heating system. Read instructions carefully. If you are unclear as
to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this
fixture.
FIXTURE ASSEMBLY
Carefully removed the fixture from the carton and check that all
parts are included as shown in figure. Be careful not to misplace
any of the screws or parts, which are needed to install this fixture.
INSTALLATION
IMPORTANT: Do not attach fixture directly to outlet box.
STEP 1: Secure back plate (A) to outlet box with outlet box
screws (B), then allowing for the wood screws (C) to
protrude through the back plate （A) holes onto the
plastic wall anchors(D), and secure wood screws (C).
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two
raised dimples on the circular strap. Wrap the ground
wire from the fixture (if supplied) around the green
grounding screw, then connect it to ground wire from the
outlet box (if not fixed on the outlet box) using a wire
connector (not supplied). If ground wire from the fixture is
not supplied, wrap the ground wire (if not fixed on the
outlet box) from the outlet box around the green
grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your fixture.
Identify which group your fixture wire(s) falls into and
connect the wires according to the directions below:
*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer
wire is square shaped or ridged and the less tracer wire is round
in shape or smooth (seen best when viewed from wire end.)
STEP 3: Take your fixture wire(s) from group A and place
evenly against the black wire from the outlet box. Do
STEP 4: Fit a wire connector (not supplied) over the wires and
STEP 5: Try gently to pull the connector off the wires. If you can
STEP 6: Connect the fixture wire from group B to the white wire
NOT twist wires together before using wire connectors.
screw the connector clockwise until you feel a firmness.
pull the connector off, carefully re-do steps 3 and 4, as
above, and check again for a firm connection.
from the outlet box in the same manner. Make sure no
bare wires can be seen outside wire connectors.
FINAL ASSEMBLY
STEP 1: After wires are connected, install the face plate (E)
onto the back plate (A), then secure with the screws (F)
into the face plate (E) to the back plate (A).
STEP 2: Place the glass (H), check ring (I) over the socket (G),
then secure with socket ring (J)
STEP 3: Install light bulb. (Please do not exceed the
maximum capacity recommended on the socket.)
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to
order replacement parts. All parts for this fixture can be ordered
from place of purchase. Be sure to use exact wording from
illustration when ordering parts.
Line art shown may not exactly match the fixture enclosed.
However, the installations do apply to this fixture.
Loading...