Zip HT1791 Specifications Sheet

Zip HydroTap® G4 All-In-One BCHA “Vented”

G4

TECHNOLOGY

G4

TECHNOLOGY

G4

TECHNOLOGY

G

Y

Boiling | Chilled | Filtered | Instantly | Hot + Cold

WELS rating is for mixer tap

Residential Specification Sheet | Z0775 June 2014

New under-bench Zip G4 Command­Centre™ leads the world in energy-saving
technology, has a pin-code protected
touch-screen to simplify adjustments, and
automatically monitors performance to give
an operating history if ever needed.

5

Australian Made

Year

Warranty

G4

T

*

E

C

H

N

L

O

Y

G

O

Boiling & chilled filtered water instantly, plus hot & cold
water, all from a single tap. “Vented” model connecting
to incoming cold water supply only.

1. Saving energy.

• Superior Zip G4 thermal insulation now significantly reduces

standard heat loss.

• Power-Pulse™ technology maintains boiling water to within

0.2°C of set temperature.

• Boiling temperature can be pre-set to taste: from 100°C down

to 68°C.

• Sleeps or “powers-off” after two hours of non-use, to minimize

daily power consumption.

• Automatically sleeps when the kitchen goes dark for added

power savings overnight.

• Inbuilt 24/7 automatic timer turns power on and off over

weekends or weekday periods.

2. User safety.

• Choice of fingertip control for fast cup filling (lever down) or

hands-free pot filling (lever up).

• Can be set to finger-thumb operation to access boiling water,

eliminating risk of accidental use.

• Can also be set to boiling water “isolation mode” for total safety

when kitchen is unattended.

3. Healthier drinking.

• Inbuilt Zip 0.2 micron NSF-certified filter puts crystal-clear better-

tasting water on tap, filtering out chlorine taste and odour and
impurities as tiny as one five-thousandth of a millimetre,
including protozoan cysts such as Cryptosporidium.

• Also reduces accumulation of mineral scale in boiling water

appliances, but does not remove fluoride.

• Free-Flow™ bottle filling: for continuing supply of filtered water

even when chilling capacity is exceeded. (Chilled only).

Typical Specification

All-In-One Under-bench boiling and chilled filtered water appliance
equipped two way lever action electronic tap head and the ability
to provide hot water for washing from the same outlet. Integral
500kPa pressure limiting and Dual Check valve, NSF certified

0.2 micron filter, air cooled refrigeration system with cleanable

lint filter. Full colour interactive touch screen display with pin
code protection, 2 boiling water safety modes, 3 energy saving
modes including a sensor activated “sleep when its dark” feature,
upgradable boiling water capacity.

50 min.

280

50 min.

Inlet Vent

ø

50 mm diameter hole

162 reach

135

186

Mains cold water
isolation valve
(not supplied)

Restrictaflow

Booster

Clearance
Envelope

Residential Specification Sheet | Z0775 June 2014

Zip HydroTap® G4 All-In-One BCHA “Vented”

Boiling | Chilled | Filtered | Instantly | Hot + Cold

Order Code Zip Model Rating (kW) @ 230 V Cabinet Dimensions W x D x H (mm)

HT1791 Zip HydroTap G4 BCHA “Vented” 1.55 + 2.2 280 x 476 x 333

* This model is installed with an external 2.2 kW booster. The G4 Command-Centre and booster each require a 10 amp power point.

A. Location

Tap must be positioned so that it drains into a
suitable sink. Tap should be situated as closely
as possible to directly above the under-sink G4
Command-Centre. Maximum distance from the
base of the tap to the G4 Command-Centre is
one metre (may be extended if required).
G4 Command-Centre must have clearances as
shown on the drawings. Ventilation accessories
(supplied) must be installed as per instructions.

B. Plumbing

Must be installed in accordance with
AS/NZS3500 plumbing regulations. Designed
for direct connection to a potable (drinkable)
cold water supply with minimum pressure of 172
kPa. A 500 kPa pressure limiting valve and dual
check valve are fitted internally to comply with
AS/NZS3500. An isolating valve should be fixed
between the water supply and the under-bench
G4 Command-Centre.

C. Electrical

Installed with an externally mounted 2.2 kW
booster unit (supplied), this model must be
connected via two 10 amp GPO power points
to 240-230 volt AC power supply in accordance
with AS/NZS3000 wiring regulations.

Caution

In some hard water areas where mineral
scale accumulation can become a problem,
consideration should be given to the
maintenance required. All G4 Command-Centre
units come with an internal bypass to simplify
the connection of an added external filtration or
water softening system.

Warranty

Five year warranty.
Appliance warranty 36 months
plus additional 24 months tank
warranty. See website for details.

Accessories

91290 – Zip 0.2 micron replacement filter

Standard tap finish: bright chrome.
Brushed chrome or black also available.
Call Zip for details and a quotation.

Technical Assistance

Zip Heaters (Aust) Pty Ltd
67-77 Allingham Street
Condell Park NSW 2200
Free Call 1800 638 622

www.zipindustries.com

As Zip policy is one of continuous product
improvement, changes to specifications may
be made without prior notice. The terms ‘Zip’,
‘HydroTap’, ‘Power-Pulse’, ‘Free-Flow’ and
‘G4 Command-Centre’ are trade marks.

Note: Zip HydroTap All-In-One “vented”
models are designed to be connected to
only a cold incoming water supply. For
alternative models connected to both hot
cold incoming water supplies, to provide a
larger volume of hot water for dish washing,
refer to “mains” models.