Zip HT1788 User Manual
Zip HydroTap® G4 C
G4
TECHNOLOGY
G4
TECHNOLOGY
G4
TECHNOLOGY
G
Y
Chilled | Filtered | Instantly
Residential Specification Sheet | Z0771 June 2014
New under-bench Zip G4 CommandCentre™ leads the world in energy-saving
technology, has a pin-code protected
touch-screen to simplify adjustments, and
automatically monitors performance to give
an operating history if ever needed.
5
Australian Made
Year
Warranty
G4
T
*
E
C
H
N
L
O
Y
G
O
Chilled filtered water instantly. Simply chilled filtered
water for kitchen, ensuite, cabana or gym.
1. Inexpensive to run.
• Choice of 3 pre-set chilled water ranges.
• Inbuilt 24/7 automatic timer turns power on and off over
weekends or weekday periods.
2. Simple to operate.
• Choice of fingertip control for fast glass filling (lever down)
or hands-free carafe filling (lever up).
• Free-Flow™ bottle filling: for continuing supply of filtered water
even when chilling capacity is exceeded. (Chilled only).
3. Healthier drinking.
• Inbuilt Zip 0.2 micron NSF-certified filter puts crystal-clear better-
tasting water on tap, filtering out chlorine taste and odour and
impurities as tiny as one five-thousandth of a millimetre,
including protozoan cysts such as Cryptosporidium.
• Also reduces accumulation of mineral scale, but does not
remove fluoride.
Typical Specification
“Under-bench chilled filtered drinking water appliance equipped
with an electronic tap head with lever action controls, electronically
controlled under-bench G4 Command Centre with NSF certified
0.2 micron filtration, inbuilt 500 kPa pressure limiting and dual
check valve, and a pin-code-secured full colour touch screen
display.
100
ø
35 mm hole required if the G4 Tap is fitted to sink
50 min.
280
50 min.
Inlet Vent
Mains cold water
isolation valve
(not supplied)
Clearance
Envelope
Residential Specification Sheet | Z0771 June 2014
Zip HydroTap® G4 C
Chilled | Filtered | Instantly
Order Code Zip Model Rating (kW) @ 230 V Cabinet Dimensions W x D x H (mm)
HT1788 Zip HydroTap G4 C 0.125 280 x 476 x 333
Order code shown here is for the model installed at a sink. To install on a “font” also specify a font kit: order code 90915.
A. Location
Tap must be positioned so that it drains into a
suitable sink, or be installed on the optional tap
“font kit” which is plumbed to waste. Tap should
be situated as closely as possible to directly above
the under-sink G4 Command-Centre. Maximum
distance from the base of the tap to the G4
Command-Centre is one metre (may be extended
if required). G4 Command-Centre must have
clearances as shown on the drawings. Ventilation
accessories (supplied) must be installed as per
instructions.
B. Plumbing
Must be installed in accordance with
AS/NZS3500 plumbing regulations. Designed for
direct connection to a potable (drinkable) cold
water supply with minimum pressure of 172 kPa.
A 500 kPa pressure limiting valve and dual check
valve is fitted internally to comply with
AS/NZS3500. An isolating valve should be fixed
between the water supply and the under-bench
G4 Command-Centre.
C. Electrical
Designed to be connected to a 10 amp GPO,
240-230 volt AC power supply in accordance
with AS/NZS3000 wiring regulations.
Caution
In some hard water areas where mineral
scale accumulation can become a problem,
consideration should be given to the
maintenance required.
Warranty
Five year warranty.
Appliance warranty 36 months
plus additional 24 months tank
warranty. See website for details.
Accessories
90915 – Zip font installation kit
91290 – Zip 0.2 micron replacement filter
Standard tap finish: bright chrome.
Brushed chrome or black also available.
Call Zip for details and a quotation.
To order any model to be supplied with extension
levers and Braille pads, add D to the end of the
order code.
Technical Assistance
Zip Heaters (Aust) Pty Ltd
67-77 Allingham Street
Condell Park NSW 2200
Free Call 1800 638 622
www.zipindustries.com
As Zip policy is one of continuous product
improvement, changes to specifications may
be made without prior notice. The terms ‘Zip’,
‘HydroTap’, ‘Power-Pulse’, ‘Free-Flow’ and
‘G4 Command-Centre’ are trade marks.
Loading...