Zip HT1787Z3-91295, HT1787-91295 Installation Guide
File Ref : C:\Zip_PDM\Engineering\Projects\Project 10002\2. Design\Residential HydroTap G4 CS\KL002_0056AU0S2ZN1R (Sheet1)
50
Sheet1 (Default)
400
Item
1
11 802084
12 800221
13 800349
17
18
19
Part
800544-CS
83393
0056AU
A2672
Rev
00
A04
C
A
A13
00
01
Table - Zip BOM (Assembly)
Description
Tap Assy Commercial - Chilled Sparkling HydroTap G4
"Y" Connector JG 1/4"
Air Inlet Grill CFF
1.2kg CO2 Cylinder Assy
Ventillation Grille Hafele
HydroTap G4 Residential CS Base Module Upgraded 2016
w/ IEC
IEC Female Plug
100
Config
Default
Default
Default
Default
Default
Default
Default
Status
Design
Pending Pre-
Production
Production
Production
Pending Pre-
Production
Design
Pending Pre-
Production
Qty
150
Notes
1
1
1
1
1
1
1
200
Position the Tap such that it dispenses into the sink bowl
with ample clearance for a cup or a tea pot. Alternatively, the Tap
could be mounted away from the sink using a Zip Font available
as an accessory.
250
300
350
400
450
116 CL reach
500
THIRD ANGLE
PROJECTION
Dimensions in
millimetres
Drawing to
BS8888:2004
Screw threads to
BS 8498:2008
550
Zip Industries Pty Ltd
67 Allingham Street
Condell Park
Sydney
NSW 2200
Australia
Web : www.zipindustries.com
Email : sales@zipindustries.com
400
350
300
250
35 Hole
G4 Tap
209
46
126
Sink shown
only
A
4 min.
Buffer Pad
Air Space
350
308
232
300
6
104
219
250
DETAIL FONT
200
150
200 min
333
CO
2
cylinder
Clearance
Envelope
240 - 230V,
50Hz GPO
Clearance
Envelope
SCALE 1 : 5
219
circumference
35 hole for
tap tubes
83
21
200
150
60
100
Inlet Vent
10 cut-away for
6mm fastening
stud
108 hole
for bowl
100
405
Mains cold water
This drawing is CONFIDENTIAL and is supplied on the express condition that it shall not be LOANED, COPIED or DISCLOSED to
50
50 min 50 min
280
A
isolation valve
SECTION A-A
(not supplied)
SCALE 1 : 5
WMKA 00099; CS8328
Watermark Exp: 26-10-2017; CS Exp: 18-8-2014
50
100
150
200
250
300
350
any other third party or used for any purpose without the written consent of Zip Industries Pty Ltd. If this document is printed in
hardcopy form, it is for INFORMATION ONLY and therefore not subject to updating controls.
For the current revision ALWAYS refer to the NATIVE electronic form as stated in the top left-hand corner of this sheet.
© copyright Zip Industries Pty Ltd, 16/05/2011
Manufacturing Instructions
Make or Buy :
Manufacturing Route :
Raw material :
Remove all sharp edges. This drawing ONLY details information
which cannot be ascertained from the 3D geometry of the part(s)
attached. Model & dimensions are AFTER all finishing operations
Comments :
Larger Compressor & Carbonator
Potable? :
Buy
Manufacturing Process
See Components
Recyclable? :
No No
Handed? :
No
Approved by :
Checked by :
Updated by :
Material :
See Components
Finish :
Finish
Volume
Mass
nickm on 11/11/2014
edgarg on 18/04/2016
edgarg on 18/04/2016 3:08:14 PM
:
(cm3)
78600.0
:
(g)
86413.8
Area
Density
(cm2)
:
(g/cm3)
:
Zip Industries
Description :
Assy - Kitchen Layout (HydroTap G4 Residential
Chilled Sparkling Unit & G4 Tap Upgraded)
Hydrotap G4®
Project :
KL002_0056AU0S2ZN1R
Model :
Drawing :
KL002_0056AU0S2ZN1R
Derived from :
134043.1
1.1
Scale :
1:1
New
Sheet : 1 of
1
Configuration : Default
Configuration :
Created by & on
Colour :
Status :
_Drawing
Property
Default
EdgarG on 4/05/2011
Created by & on
EdgarG
on 16/05/2011
Colourless
Pending Pre-Production
Part
Property
R
Rev
01
Size
A2
Loading...