Zip HT1786 Product Sheet
Zip HydroTap® G4 B
G4
TECHNOLOGY
G4
TECHNOLOGY
G4
TECHNOLOGY
G
Y
Boiling | Filtered | Instantly
Residential Specification Sheet | Z0770 June 2014
New under-bench Zip G4 CommandCentre™ leads the world in energy-saving
technology, has a pin-code protected
touch-screen to simplify adjustments, and
automatically monitors performance to give
an operating history if ever needed.
5
Australian Made
Year
Warranty
G4
T
*
E
C
H
N
L
O
Y
G
O
Boiling filtered water instantly. Simple way to have
filtered boiling water on tap in a home kitchen.
1. Saving energy.
• Superior Zip G4 thermal insulation now significantly reduces
standard heat loss.
• Power-Pulse™ technology maintains boiling water to within
0.2°C of set temperature.
• Boiling temperature can be pre-set to taste: from 100°C down
to 68°C.
• Sleeps or “powers-off” after two hours of non-use, to minimize
daily power consumption.
• Automatically sleeps when the kitchen goes dark for added
power savings overnight.
• Inbuilt 24/7 automatic timer turns power on and off over
weekends or weekday periods.
2. User safety.
• Choice of fingertip control for fast cup filling (lever down) or
hands-free pot filling (lever up).
• Can be set to finger-thumb operation to access boiling water,
eliminating risk of accidental use.
• Can also be set to boiling water “isolation mode” for total safety
when kitchen is unattended.
3. Healthier drinking.
• Inbuilt Zip 0.2 micron NSF-certified filter puts crystal-clear better-
tasting water on tap, filtering out chlorine taste and odour and
impurities as tiny as one five-thousandth of a millimetre, including
protozoan cysts such as Cryptosporidium.
• Also reduces accumulation of mineral scale in boiling water
appliances, but does not remove fluoride.
Typical Specification
Under-bench boiling water appliance equipped two way lever
action electronic tap head, integral 500kPa pressure limiting
and Dual Check valve, NSF certified 0.2 micron filter, full colour
interactive touch screen display with pin code protection, 2 boiling
water safety modes, 3 energy saving modes including a sensor
activated “sleep when its dark” feature, upgradable boiling water
capacity with additional “Booster” module and the ability to adapt
to provide approx. 55˚C hot water for washing up to a secondary
outlet with additional “Vented Mixer” kit.
100
ø
35 mm hole required if the G4 Tap is fitted to sink
50 min.
280
50 min.
Mains cold water
isolation valve
(not supplied)
Clearance
Envelope
Residential Specification Sheet | Z0770 June 2014
Zip HydroTap® G4 B
Boiling | Filtered | Instantly
Order Code Zip Model Rating (kW) @ 230 V Cabinet Dimensions W x D x H (mm)
HT1786 Zip HydroTap G4 B 1.425 280 x 313 x 333
Order code shown here is for the model installed at a sink. To install on a “font” also specify a font kit: order code 90915.
A. Location
Tap must be positioned so that it drains into a
suitable sink, or be installed on the optional tap
“font kit” which is plumbed to waste. Tap should
be situated as closely as possible to directly above
the under-sink G4 Command-Centre. Maximum
distance from the base of the tap to the G4
Command-Centre is one metre (may be extended
if required). G4 Command-Centre must have
clearances as shown on the drawings.
B. Plumbing
Must be installed in accordance with
AS/NZS3500 plumbing regulations. Designed
for direct connection to a potable (drinkable)
cold water supply with minimum pressure of 172
kPa. A 500 kPa pressure limiting valve and dual
check valve are fitted internally to comply with
AS/NZS3500. An isolating valve should be fixed
between the water supply and the under-bench
G4 Command-Centre.
C. Electrical
Designed to be connected to a 10 amp GPO,
240-230 volt AC power supply in accordance
with AS/NZS3000 wiring regulations.
Caution
In some hard water areas where mineral
scale accumulation can become a problem,
consideration should be given to the
maintenance required. All G4 Command-Centre
units come with an internal bypass to simplify
the connection of an added external filtration or
water softening system.
Warranty
Five year warranty.
Appliance warranty 36 months
plus additional 24 months tank
warranty. See website for details.
Accessories
90915 – Zip font installation kit
91290 – Zip 0.2 micron replacement filter
Standard tap finish: bright chrome.
Brushed chrome or black also available.
Kits for increasing boiling water capacity of
this installed G4 model or its conversion to
a 3-In-1 can be supplied.
Call Zip for details and a quotation.
Accessibility
To order any model to be supplied with extension
levers and Braille pads, add D to the end of the
order code.
Technical Assistance
Zip Heaters (Aust) Pty Ltd
67-77 Allingham Street
Condell Park NSW 2200
Free Call 1800 638 622
www.zipindustries.com
As Zip policy is one of continuous product
improvement, changes to specifications may
be made without prior notice. The terms ‘Zip’,
‘HydroTap’, ‘Power-Pulse’, ‘Free-Flow’ and
‘G4 Command-Centre’ are trade marks.
Loading...