Zip CT1002 Installation Guide

File Ref : T:\Engineering\!Published\KL003_60009 (Sheet1)

Sheet1 (Default)

400

Item

Part

A2402

87570!

83453

60007!

800426

800332!

89446

89635

350

83908

Table - Zip BOM (Assembly)

Rev

Description

Assy - Kitchen Cupboard (Generic)

Assy - Tap (4 in 1)

Assy - Pressure LimitIng Assembly FM600

60 Glass/Hr Filtered UCCT12FMV Chilltap

Description (Assembly)

Filter Cartridge

Tap - Chilltap Extra (Vented)

Chilltap Extra PRV Assy

Tee 1/4" x 1/4" JG

35 Hole

100

Config

LH & RH Taps

Hot Off

Default

800332

Default

Status

Production

Qty

150

Notes

Position the Tap such that it dispenses into the sink bowl with ample clearance for a cup or a tea pot. Alternatively, the Tap could be mounted away from the sink

200

250

300

350

400

Limits unless otherwise stated:

Fabricated Sand-Cast 0.352. Forging 0.25 3. Die-Cast 0.254. Moulded 0.155. Machined 0.25mm6. Angular 0.50degree7.

Fits unless otherwise stated:

Free Running = H9/d91. Running = H8/f82. Clearance = H7/h63. Sliding = H7/g64. Interference = H7/u65.

450

0.751.

Surface finishes unless otherwise stated:

Sand-Cast = 16.0µm1. Drilling = 6.3µm2. Forging = 6.3µm3. Milling = 3.2µm4. Turning = 3.2µm5. Boring = 3.2µm6. Die-Cast = 1.6µm7. Reaming = 1.6µm8. Grinding = 0.8µm9. Honing = 0.4µm10. Polishing = 0.2µm11.

500

THIRD ANGLE

PROJECTION

Features marked with this symbol: must be referred to in the manufacturing control plan

Dimensions in

millimetres

Drawing to

BS8888:2004

Screw threads to

BS 8498:2008

REVISIONS

XXXX

Rev

YYYY

Last Change(s)

First Issue

550

Zip Industries Pty Ltd

67 Allingham Street Condell Park Sydney NSW 2200 Australia

Web : www.zipindustries.com

Email : sales@zipindustries.com

XXX.XX

ECO

0000

8/06/2011

Date

400

Init

350

using a Zip Font available as an accessory.

300

250

Chilltap Extra®

Sink shown only

Pressure

relief valve

Tap

214

4 min. Buffer Pad Air Space

214

7 max.

100

300

295

250

200

150

200 min.

377

Clearance Envelope

Filter

240 - 230V, 50Hz GPO

Clearance Envelope

Hole

104

219

DETAIL FONT

SCALE 1 : 5

200

150

100

Pressure

253

65 min.

Limiting Valve

Configuration : Default

SECTION

50 min.

353

50 min.

Mains Cold water isolation valve

100

150

200

250

300

SCALE

ERROR!:Approval Number

ERROR!:Approval Expiry Date

350

A-A

1 : 5

This drawing is CONFIDENTIAL and is supplied on the express condition that it shall not be LOANED, COPIED or DISCLOSED to any other third party or used for any purpose without the written consent of Zip Industries Pty Ltd. If this document is printed in hardcopy form, it is for INFORMATION ONLY and therefore not subject to updating controls. For the current revision ALWAYS refer to the NATIVE electronic form as stated in the top left-hand corner of this sheet. © copyright Zip Industries Pty Ltd, 16/05/2011

Manufacturing Instructions

Make or Buy :

Manufacturing Route :

Raw material :

Remove all sharp edges. This drawing ONLY details information which cannot be ascertained from the 3D geometry of the part(s) attached. Model & dimensions are AFTER all finishing operations

Comments :

Comments

Potable? :

Make

Manufacturing Process

Raw Material

Recyclable? :

No No

Handed? :

ERROR!:Hand ed Part?

Approved by :

Checked by :

Updated by :

Material :

Material <not specified>

Finish :

Finish

Volume

Mass

Unapproved on 1/03/2011

Unchecked on 1/01/2001

edgarg on 17/06/2014 10:13:59 AM

(cm3)

83884.85

(g)

93961.66

Area

Density

(cm2)

(g/cm3)

Zip Industries

Description :

Assy - Kitchen Layout Chill Tap Extra

- Residential

ChillTap®

Project :

KL003_60009

Model :

Drawing :

KL003_60009

Derived from :

120612.23

1.12

Scale :

1:1

New

Sheet : 1 of

Configuration :

Created by & on

Colour :

Status :

_Drawing

Property

Colourless

Prototype

Default

EdgarG on 4/05/2011

Created by & on

Engineer

on 16/05/2011

Part

Property

Rev

Size