Zioncom WL0159 User Manual

r

WIFI MODULE
IEEE 802.11g/b

Model No: WL0159

Product Description

ZC-WL0159 is a high-gain wireless PIN Interface adapter
which provides a s imple and easy way to add or upgrade
wireless connectivity to your desktop or notebook
computer. You can just plug it into computer's

USB 2.0 Connector

wireless network access.

Product Features

port and enjoy incredible high-speed

A-type

 Complies with IEEE 802.11g; 802.11b standard for

2.4GHz Wireless LAN.

Product Specification

Standard

Modulation
Type

Interface
Frequency

Transmission
Distance

Data Rate

Transmit Powe

Data Security

LED Indicator
Operating

Temperature
Storage

Humidity
Operating

System

IEEE802.11g; IEEE 802.11b
OFDM with BPSK, QPSK,
16QAM,64QAM (11g)
BPSK, QPSK, CCK (11b)
4PIN Interface

2.4~2.4835 GHz
Indoor up to 100m , outdoor up to
300m (it is limited in an
environment)
11b 1/2/5.5/11Mbps
11g 6/9/12/24/36/48/54Mbps
Auto fallback
15 dBm (Typical)
64/128-bit WEP Data Encryption,
WPA (TKIP with IEEE 802.1x) and
AES

Link/Activity

0 ~ 55℃

-40°C~70°C (-40℉~158℉)
5 ~ 95% non-condensing
Windows 2000, XP32/64,

Vista32/64, Linux,Mac

Wireless

802.11g/b Adapter

 Supports Ad-Hoc/Infrastructure modes
 Supports PC Card hot-SWAP and true Plug & Play.
 Works with all existing network infrastructure.
 Supports Wi-Fi Protected Setup (WPS) configuration

function

 Capable of up to 128-Bit WEP Encryption.
 Freedom to roam while staying connected.
 22-Mbps Packet Binary Convolution Coding (PBCC)

(according to the IEEE Std 802.11b high-rate
specification ).

 UP to 54 Mbps High-Speed Transfer Rate in 802.11g

mode of operation.

 Rich diagnostic LED indicators with Integrated Antenna.
 Supports Windows 2000, XP32/64,Vista32/64,

Linux,Mac

 Low power consumption.
 Easy to install and configure.

FCC Statement

This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference

to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the
following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and
receiver.

-Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician
for help.
To assure continued compliance, any changes or
modifications not expressly approved by the party
responsible for compliance could void the user’s authority
to operate this equipment. (Example- use only shielded
interface cables when connecting to computer or peripheral
devices).

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment and it also
complies with Part 15 of FCC RF Rules. Operation is
subject to the following two conditions:

1) This device may not cause interference and

2) This device must accept any interference, including
interference that may cause undesired operation of the
device.

Caution!

The manufacturer is not responsible for any radio or
TV interference caused by unauthorized
modifications to this equipment. Such modifications
could void the user authority to operate the
equipment.

1. This device and its antenna(s) must not be
co-located or operating in conjunction with any
other antenna or transmitter.

2. This compliance to FCC radiation exposure limits
for an uncontrolled environment, and minimum of
20 cm separation between antenna and body.

3. Only the type of chip antenna tested may be used.

4. The end product must carry a label stating
"Contains TX FCC ID: X7D-WL0159".