Zigen ZIG-HAVEX User Manual
Function
TRANSMITTER
RECEIVER
HDMI In
Connector
HDMI A-Type Female
x 1
None
HDMI Out
Connector
HDMI A-Type Female
x 1
RJ-45 Connector
1
RJ-45 Connector
(with LED)
4
RS-232
Connector
1
Audio Input
None
1 Stereo RCA(L/R)
1 RCA(Coaxial)
1 Digit Optical
TOSlink
Audio Output
1 set RCA(L/R)
1 RCA(Coaxial)
1 Digit Optical
TOSlink
None
IR OUT
3.5ψ Stereo Jack x 1
3.5ψ Stereo Jack x 1
IR IN
3.5ψ Stereo Jack x 1
None
IR1 IN
None
Internal IR receiver
IR2 IN
None
3.5ψ Stereo Jack x 1
Max. Resolution
1080P 60Hz / 4K x 2K
Cable Distance
100 m (Max.)
Power Adapter
(Min.)
DC 48V with lock
None
Housing
Metal
Weight
690g
695 g
Dimensions
(LxWxH)
245x120x25 mm
ZIG-HAVEX
HDMI EXTENDER
USER MANUAL V1.0
Transmitter Receiver
Package Contents-
1x ZIG-HAVEX Transmitter Unit
1x ZIG-HAVEX Receiver Unit
1 user manual
1x Power adapter DC 48V with lock
1x IR Receiver Cable
4x screws
8x foot pads
Supports 10/100 base-T Ethernet switcher
(Compliant IEEE802.3, IEEE802.3u, IEEE802.3x)
8 standard Ethernet port (with switching capabilities on
each unit.
Supports IR/RS-232/Ethernet extension function.
IR extension function(Supports all frequency band IR
control)
Supports 3D pass-through
Supports CEC pass-through
Support RS-232(Bi-direction transfer)
Supports HDTV up to 1080p/60 4K x 2K
HD-baseT technology
Extend HDMI signal up to 100 meter 328 feet by using
a single cat-6/7 cable. You may also use a cat-5 cable
to extend up to 80 meters 260 feet.
LOCAL TOP VIEW
-1-
Specifications
1. 1~4 port ETHERNET LINK/SPEED/FULL indicators.
LINK ( Flash : Activity )
SPEED ( ON : 100M, OFF : 10M )
FULL ( ON : Full duplex ,OFF : Half duplex ,
Flash : Collision)
2. POWER LED
3. HDCP LED
4. LINK LED
5. MODE LED
LOCAL FRONT VIEW
Features
ZIG-HAVEX is a transmitter / receiver extender kit for
long distance transmission of HDMI video, embedded
audio, 4-port POE Ethernet switch, back channel
analogue or digital audio plus bi-directional control
signals over a single CAT – 5 /6 /7 type cables.
Supports HDMI 1.4 with 3D function
Supports HDMI 1.2 and 1.3a
HDCP Compliant
Supports POE
1. Power jack (48V DC)
2. AUDIO OUT(R/L)
3. AUDIO OUT(COAXIAL)
4. AUDIO OUT(OPTICAL)
5. AUDIO SELECT SWITCH
000 : L/R
001: Coaxial
010: Optical
GND
+V
Sig
6. HDMI IN
7. RS-232
8. IR IN
9. IR OUT
10. IR Connector
LOCAL REAR VIEW
1. ETHERNET(1~4 port RJ-45 Connector with LED)
2. LINK (RJ-45 Connector)
-2-
REMOTE TOP VIEW
4. LINK LED
5. MODE LED
6. IR1 IN ( Internal IR receiver )
REMOTE FRONT VIEW
-3-
Installation
1. Be sure to turn OFF your HD source and HDTV.
2. Connect the HDMI extension cable between HD source
and the “HDMI IN” port of Transmitter.
3. Connect the HDMI extension cable between the HDTV
and the “HDMI OUT” port of Receiver.
4. Connect CAT.5 cables between the Transmitter “LINK”
port and the Receiver “LINK” port of extender.
5. Connect the power cord and power up the extender.
1. AUDIO IN(R/L)
2. AUDIO IN(COAXIAL)
3. AUDIO IN(OPTICAL)
4. AUDIO SELECT SWITCH
000 : L/R
001: Coaxial
010: Optical
5. HDMI OUT
6. RS-232
7. IR OUT
8. IR2 IN
9. IR Connector
REMOTE REAR VIEW
6. Turn on your HD source and HDTV.
IR Receiver
Pin configuration for 3.5mm IN terminal
DO NOT PLUG MONO TIPE IR EMITTER INTO “IR-IN”
IR-in is design to be used with IR receivers.
1. 1~4 port ETHERNET LINK/SPEED/FULL indicators.
LINK ( Flash : Activity )
SPEED ( ON : 100M, OFF : 10M )
FULL ( ON : Full duplex ,OFF : Half duplex ,
Flash : Collision)
2. POWER LED
3. HDCP LED
1. ETHERNET(1~4 port RJ-45 Connector with LED)
2. LINK (RJ-45 Connector)
Loading...