FCC and ISED Statement:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses an d can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved
equipment.
Notice: This device complies with Part 15 of the FCC Rules and with Industry
Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1)this device may not cause harmful interference, and
(2)this device must accept any interference received, including interference
that may cause undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Radiation Exposure Statement
This equipment complies with FCC/ISED RF radiation exposure limits set
forth for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20 centimeters between the radiator and
your body.
by manufacturer could void your authority to operate this
1. Subject Matter Scope
This standard specifies the Rocateq’s production of Wireless 2.4 GHz
transmitter, technical requirements, test methods, inspection rules, marking,
packaging and storage.
2. Reference Standard
ANSI/ASQZ1.4-2003 each inspection sampling and sample forms (for
continuous batch of checks)
3. Terminology and code
3.1. The B signal (2.4 GHz) emitted by Wireless 2.4 GHz transmitter makes the
relevant shopping cart casters unlock after receiving A signal (8.13KHz) again.
4.Shell size (Fig. 1) (Unit: mm)
125.89
Fig.1
60.89
5. Electrical Performance and Testing
Electrical Performance of Wireless 2.4 GHz Transmitter
25.60
Testing conditions
No.
ITEM
Parameters
Others
normal
temperature
Environmental
Testing -20 ～
60℃
Over/Low
voltage
test
1
Voltage
5V + 10%
5V + 10%
5V + 10%
2
Transmitting
distance
(level4)
≥2m
+ 10%
+ 10%
3
Transmitting
frequency
2.4GHz
5.4.1 The ambient temperature ranges from - 20 C to 60 C.
5.4.2 Operating voltage: 5V + 10%;
Specification of adapter: input: AC100-240V, output: DC5V, 1000mA
5.4.3 Accessories: ammeter, DC power supply, adapter, remote control,
test casters, OCS RFID casters and Wireless B signal meter
5.4.4 Test methods:
1.Current test: DC power supply is adjusted to 5V, wireless 2.4 GHz
transmitter is connected with ammeter in series, power is adjusted from 1 to P
(10) by remote control, input current is less than 300 mA.
2. Transmitting distance test:
2.1.Power-on and debugging: The adapter connects 220VAC, the
output connects to Wireless 2.4 GHz transmitter, the power is adjusted to level
4 with remote control, the delay is adjusted to 0 seconds, horizontal on the
ground, the digital tube is displayed, and the wireless side is in front of the test.
2.2. Testing special caster to measure distance: pushing the shopping
cart when the caster is unlocked, pushing the cart several times (unlocking,
unlocking continues), maximum unlocking distance ≥2m.
2.3. Wireless B signal meter test distance: Hold the wireless B signal
meter as high as Wireless 2.4 GHz transmitter, move forward and backward,
the maximum receiving distance is more than 2 m.
3. OCS RFID Caster Test Delay: When the caster is unlocked, it receives
an A signal and receives a wireless signal (B signal) emitted by Wireless 2.4
GHz transmitter after 30 seconds. The receiving time is more than 0 seconds
(delay), and then receives an A signal. The caster is unlocked. In this test, the
wireless 2.4 GHz transmitter is set with a remote controller to delay 3 seconds,
5 seconds, 10 seconds, 20 seconds, 30 seconds and 60 seconds. In the second
test, when the receiving time is greater than or equal to the delay time, the
casters are not locked, and when the receiving time is less than the delay time,
the casters are locked.
4. 24-hour reset button test: 24 hours after the start of Wireless 2.4 GHz
transmitter, the remote control and the buttons on the board can not be set, and
the reset button can only be set after pressing the reset button.
6. Inspection Rules
6.1.1 Exit Inspection Contents See 6.1-6.4
6.1.2 Exit inspection shall be carried out batch by batch according to
ANSI/ASQZ1.4-2003.
5.2 type inspection
6.2.1 When wireless 2.4 GHz transmitter has one of the following conditions,
it should be type checked:
A. Trial-formulation type identification of new or old products transferred to
factories;
B. When the design, process and material of the product have changed
significantly;
C. When production is suspended for more than eight months and put into
operation again;
D. Normally continuous production of products, once a year;
E. When the State Quality Supervision Authority puts forward the
requirements for type inspection.
6.2.2 When any item of Wireless 2.4 GHz transmitter in type inspection is
not qualified, double sampling should be taken from the same batch of products
and the unqualified items should be re-examined. If any item in the
reexamination is not qualified, the batch of products will not be qualified.
Unqualified products shall be re-submitted for testing after improvement or
repairs.
6.3 Check before acceptance
The orderer accepts the products according to the ex-factory inspection
items. In case of quality disputes, both the supplier and the demander review
the products according to the supply agreement.
7. Marking, packaging and storage
7.1 Marks, which should include trademarks
7.2 Packing
Battery switches should be properly packed for each factory
7.3 Keep in storage
Wireless 2.4 GHz transmitter (including the packed wireless 2.4 GHz
transmitter) should be stored in a well ventilated warehouse with a relative
humidity not exceeding 80% and no corrosive gas for 12 months.
6
5
4
3
2
1
D D
60.89
125.89
C C
B B
25.60
DIMENSIONS ARE IN MM
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
A A
6
5
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
Zhuhai Rocateq Technology Co., LTD
ANY REPRODUCTION IN PART OR AS A
WHOLE WITHOUT THE WRITTEN PERMISSION
Zhuhai Rocateq Technology Co., LTD
OF
IS PROHIBITED.
.
4
NEXT ASSY
APPLICATION
USED ON
TWO PLACE DECIMAL
THREE PLACE DECIMAL
MATERIAL
FINISH
DO NOT SCALE DRAWING
BEND
--
--
3
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
NAME
Sean Du
DATE
SIZE
DWG. NO.
A
SCALE:1:2
2
Zhuhai Rocateq
Technology Co., LTD
Wireless B Housing
WEIGHT:
REV.
SHEET 1 OF 1
1
Loading...