Zhuhai FTZ Oplink Communications WLS01 User Manual

Operation

-3-

1. Put the detector at place where you want, within the flood sensor detection range

when where is leaking all over the place, and both the two probes detect water at the
same time, the sensor will be triggered and send signal to your receiver.

2. Normal operation, the LED will not light.

3. If the cover of sensor is removed, the tamper switch will send signal according the

Status/Signal table, and the LED will go flash once.

Federal Communications Commission Statement

This equipment has been followed to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try and
correct the interferene by one of the following measures:

- Reorient or relocate the receiving antenna,

- Increase the separation between the equipment and receiver,

- Connect the equipment into and outlet on a circuit different from that to

which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undersired
operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.

Limited Warranty

OPLINK Guarantees that every flood sensor is free from physical defects in material and
workmanship under normal use for one year from the date of purchase. If the product
proves defective during this one-year warranty period, OPLINK will replace it free of
charge. OPLINK does not issue any refunds. This warranty is extended to the original end
user purchase only and is not transferable. This warranty does not apply to : (1) damage
to units caused by accident, dropping or abuse in handling, or any negligent use; (2) units
which have been subject to unauthorized repair, taken apart, or otherwise modified; (3)
units not used in accordance with instruction; (4) damages exceeding the cost of the
product; (5) transit damage, initial installation costs, removal cost, or reinstallation cost.
For information on addional devices, plesae visit us at www.oplink.com

Installation & Operation Manual

Water Leak Sensor

(Flood Sensor)

WLS1300

Introduction

Specification:

Package Content:

Frequency: 433.92MHz
Operating Range: Up to 100 feet line of sight
Operating Temp.: -15°C~ 60°C (5°F ~140°F)

1pc
1pc
1pcs
2pc
2pc
2pc

WLS1300 sensor
CR123A Battery
Installation & Operation manual
Adhesive tape for main unit
Screws for bracket of main unit
Screws for sensor

Alarm Type

Water Leak Alarm

1111 0010 1001 000X

Water Leak Release

1111 0010 1010 000X

Temper Alarm

1111 0010 1001 010X

Low Battery Alarm

1111 0010 1001 001X

Heart Beat

1111 0010 1001 011X

-1-

Thanks for choosing the OPLINK flood sensor of the home security device. This sensor
sends signal when it detects water. We can put it under the refrigerator, and the sensor will
triggered when the refrigerator leaking and both the two probes of detector detect water at
the same time. You can also set the detector at anywhere leaks; with this sensor you can
avoid loss before the calamity and the flood.

Product Description and Specification

Status/ Signal (Alarm report)

Installation

1. Fix the detector on position you want, using the screws to fix it on the wall or floor.

2. Unscrew the screw fastening the rear cover and slide the rear cover down and Insert a
CR123A battery into the battery compartment and LED will start to flashing, which
means the sensor has send alarm report signal.

3. Slide back the rear cover and screw fastening with the front cover, the LED should go
off.

4. Put the main part at higher place for better RF range, and then use the adhesive tape
to fix the main part on the wall.

-2-