Zhuhai FTZ Oplink Communications PIR02 User Manual

Federal Communications Commission Statement

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try and correct the interferene by one of the following measures:

- Reorient or relocate the receiving antenna,

- Increase the separation between the equipment and receiver,

- Connect the equipment into and outlet on a circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undersired
operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.

Limited Warranty

Oplink Guarantees that every wireless PIR sensor is free from physical defects in material
and workmanship under normal usage for one year from the date of purchase. If the
product proves defective during this one-year warrany period, Oplink will replace it free of
charge. Oplink does not issue any refunds. This warnnty is extended to the original end
user purchase only and is not transferable. This warranty does not apply to : (1) damage to
units caused by accident, dropping or abuse in handling, or any negligent usage; (2) units
which have been repaired, taken apart, or modified by an unauthorized personnel; (3) units
not used in accordance with instruction; (4) damanges exceeding the cost of the produt; (5)
transit damage, initial installation costs, removal cost, or reinstallation cost.
For information on addional devices, plesae visit us at www.oplink.com

PIR1301 V0 1000908 6B1H-31003

Installation & Operation Manual

PIR1301

Wireless PIR Motion Sensor

Introduction

Thanks for choosing the Oplink’s wireless PIR motion sensor of the home security device.
This sensor monitors movement, and send signal when movement is detected inside the
building. System comes with pet mode build inside for optional function.

Product Description and Specification

*** For indoor use only ***

3. Close the cover back to sensor.

4. To home security controller into learning mode. Press “Program Switch” on the back
of PIR1301 to learn device into system.

5. Using adhesive tape to mount PIR1301 at 2 meters above surface. To enhance
proper operation, place PIR1301 on the angle which can detect the room widely. The
solid area means the detector’s coverage range.

Specification: Package Content:

Frequency Range: 433.92MHz
Operating Range: Up to 100 feet line of sight

Operating Temp.: -15°C~ 40°C (5°F~104°F)
Battery: Panasonic CR123A * 1PC

PIR1301 sensor

1pc

Adhesive tape for sensor

1pc

CR123A Lithium Battery

1pc

Installation & Operation

1pc

Manual

Installation

1. Release cover tab to open the cover.

2. Before insert the CR123A battery, user shall decide whether this device need to be
activated when “Stay arm”. In normal case, PIR will not activate when user stay at
home while arm the system. However, some area user won’t even entry, so PIR1301
will let user to choice whether PIR1301 should activated while stay arm.

Hold tamper switch on PIR1301 while insert the CR123A battery, if LED flash twice, it
means this PIR Senor won’t activated while system at Stay Arm stage. If this is not
the function you want, please remove battery, then hold tamper switch & insert battery
again. Then LED shall flash three times, it means this PIR Sensor will activated all
the time at Stay Arm or Away Arm stage.

-1-

Operation

1. Walk in front of PIR1301, sensor will send the signal to system, and the LED will flash
five times.

2. Normal operation, the LED will not light.

3. The PIR1301 sensor equipped with tamper switch. If the cover of sensor is removed,
the PIR sensor will report a zone tamper to the controller, and the LED will flash five
times.

4. If pet in house, user can choice “pet mode”. Please refer to Product Description and
Specification for installation.

5. If PIR motion sensor is in low battery status, it will report a message to controller, and
LED will flash slow. Please change the battery.

-2-