Zhongshan K mate General Electronics BTH068 Users Manual
BTH068N
Multifunction Hi-Fi Bluetooth headset
User’s manual
Contents
Brief introduction…………...…………………………..…..................1
Before use………………………………………………..............……..1
1. Overview…………………………………………………................……1
2. Charging the Headsets…………………………………………..........…2
Getting started……..……………………………………..............……2
1. Turning on/off the headsets………………………………...........….......2
2. Pairing headsets with Bluetooth devices…………………......……..….3
1) How to enter pairing mode………………….……........…………….3
2) Pairing headset with a Bluetooth cell phone via Bluetooth……......3
3) Pairing headset with a Bluetooth cell phone via NFC.......................4
4) Pairing headset with a Bluetooth transmitter via Bluetooth…........4
5) Pairing headset with Multi-devices via Bluetooth…………....…….5
3. Making calls with the headset………………………….........……….6
4. Playing music………………………............…………………….…......8
5. LED indicator…………………………............……………………....10
6. Factory Reset……………………………............………………..….10
Care and maintenance……………………...............………..………..10
FAQs……………………………………...……...............……………..11
Specification……………………………...………..............………..…12
Welcome to use this Bluetooth stereo headset, BTH068N. Please read this
1
Retractable headband
7
Line-in jack
2
Left speaker
8
LED indicator
3
Right speaker
9
Volume up
4
MFB button/NFC zone
10
Built-in Microphone
5
Volume down
11
Charging jack
6
Switch button:Turn on/Turn
off/Pairing
user’s manual carefully before use.
Brief introduction
BTH068N is a Hi-Fi Bluetooth stereo headset. Foldable and retractable
design is very easy to take with you. It supports calling and music function ,
you can make calling wireless and enjoy high quality Bluetooth music as
you want .It also supports NFC function and can quickly connect with
Bluetooth cellphone which have NFC function.
Before use
1. Overview
1
2. Charging the headset
Functio
ns
Operation
LED indicator
Prompt tone
Turning
on
Switch button at ON
positon
Blue light on
one second
Power on
Turning
off
Switch button at OFF
positon
Red light on
one second
Power off
The headset comes with a built-in rechargeable battery, prior to using it, it is
recommended to charge the battery fully for the first time.
When the headset is low power, the headset emits waring tones every 5
minutes and the red LED flashes. Please recharge the battery of the headset.
The way of charging as following:
1. Plug USB charging cable into the standard USB port
2. Plug another side of USB cable to the Micro USD jack of headset
Red light on: Charging
Red light off: Finish charging
3. It will takes about 3 hours to finish charging
Remarks:
1) The battery is recyclable.
2) Batteries (battery pack or batteries installed) shall not be exposed to
excessive heat place, such as sunshine, fire or the like.
Getting started
1. Turning on/off the headset
2
Remark: The headset will be standby mode if turned on but not connected
Functio
ns
Operation
LED indicator
Prompt tone
Enter
pairing
mode
Keep the switch button
to Bluetooth logo
about two seconds
Red and blue
LED flash
alternately
Pairing
with devices.
2. Pairing the headset with Bluetooth devices
1) How to enter pairing mode
Remark: Pairing mode will last 2 minutes. If no devices can be connected
after 2 minutes, it will return to standby mode automatically.
2) Pairing the headset with a Bluetooth cell phone via Bluetooth
Prior to using the headset for the first time, you have to pair it with a
Bluetooth-enabled cell phone. The pairing procedures are subject to
different models of cell phones. Please refer to your cell phone user’s
manual for further information. The general pairing procedures are as
follows:
1) Keep your headset and phone within 1 meter when pairing;
2) Make the headset enter pairing mode (please refer to “How to enter
pairing mode);
3) Activate your cell phone’s Bluetooth function and set your cell phone to
search for Bluetooth devices within range, and select “BTH068N” from
the list of devices shown;
4) After successful connecting, blue LED of headset flashes twice every 4
seconds and emits “ Connected”
Remarks:
If the cellphone tips enter pairing password please enter “0000”and
confirm
After pairing is successful, the headset and the cell phone will remember
each other, they will no need to re-pair next time. Every time the headset
is turned on, it will connect to last connected device automatically.
If the headset is not connected with any devices(turned on already),short
press any button(MFB button,volume up,volume down),the headset will
try to connected to last connected devices.
3
Loading...