Zhongshan K mate General Electronics BTH033L Users Manual
BTH033L
Bluetooth stereo headset
User’s manual
Contents
Brief introduction…………...…………………………..…..................1
Before use………………………………………………..............……..1
1. Overview………………………………………………….. ..............……1
2. Charging the Headsets…………………………………………..........…2
Getting started……..……………………………………..............……2
1. Turning on/off the headsets………………………………...........….......2
2. Pairing headsets with Bluetooth devices…………………......……..….3
1) How to enter pairing mode………………….……........…………….3
2) Pairing headset with a Bluetooth cell phone via Bluetooth……......3
3) Pairing headset with a Bluetooth cell phone via NFC.......................4
4) Pairing headset with a Bluetooth transmitter via Bluetooth…........5
5) Pairing headset with Multi-devices via Bluetooth…………....…….5
3. Re-connecting with a Bluetooth device.......………………........……....6
4. Making calls with the headset…………………………….........……….6
5. Playing music…………………………............……………………..…..9
6. LED indicator……………………………............……………………..10
7. Factory Reset………………………………............………………..….11
Care and maintenance……………………...............………..………..11
FAQs……………………………………...……...............……………..12
Specification……………………………...………..............………..…13
Welcome to use this Bluetooth stereo headset, BTH033L. Please read this
user’s manual carefully before use.
Brief introduction
1. About BTH033L
BTH033L is a Bluetooth stereo headset. Foldable and retractable design is
very easy to take with you. You can enjoy music wirelessly by using
BTH033L. It Supporting NFC(Near Field Communication) function, it can
quickly connect with Bluetooth cell phone supporting NFC function.
Before use
1. Overview
1 Left speaker 8 LED indicator
2 Right speaker 8 Next track
3 Retractable design 10 Pause/ Play
4 Volume up 11 Last track
5 Volume down 12 Built-in Microphone
6 Multi-function button(MFB) 13 Line-in jack
7 Charging jack 14
1
2. Charging the headset
When the headset is low power, the headset emits three “Battery low” and
the red LED flashes. Please recharge the battery of the headset.
The way of charging as following:
Using USB cable
1. Plug USB charging cable into the USB port of computer
2. Plug another side of USB cable to the headset
Red light on: Charging
Blue light on: Finish charging
3. It will takes about 3 hours to finish charging
Remarks:
1) The battery is recyclable.
2) Batteries (battery pack or batteries installed) shall not be exposed to
excessive heat place, such as sunshine, fire or the like.
Getting started
1. Turning on/off the headset
Functions Operation Prompt tone
Turning on Press and hold MFBbutton for
3~4 seconds until blue LED
flashes
Turning off Press and hold MFB button for
3~4 seconds until red LED
flashes
Remark: In order to save pow er, the headset will turn off aut omatically if
no devices can be connected after 5 minutes.
Power on
Power off
2
2. Pairing the headset with Bluetooth devices
y
1) How to enter pairing mode
Functions Operation Prompt tone
Enter
pairing
mode
Ensure the headset is off, a nd
then press and hold MFB
button for 5~6 seconds until red
Pairing
and blue LED flash alternatel
Remark: Pairing mode will last 2 minutes. If no devices can be connected
after 2 minutes, it will return to standby mode automatically.
2) Pairing the headset with a Bluetooth cell phone via Bluetooth
Prior to using the headset for the first time, you have to pair it with a
Bluetooth-enabled cell phone. The pairing procedures are subject to
different models of cell phones. Please refer to your cell phone user’s
manual for further information. The general pairing procedures are as
follows:
1) Keep your headset and phone within 1 meter when pairing;
2) Press MFB button for 6 seconds and release it until red LED and blue
LED flashes alternately. Then your cell phone enter paring mode.
3) Activate your cell phone’s Bluetooth function and set your cell phone to
search for Bluetooth devices within range, and select “BTH033L” from
the list of device s shown; After successful connecting, the he adset emits
“your headset is connected” and blue LED flashes twice every 4 secon ds.
Remarks:
According to the indication, enter password or PIN No: “0000”( If the
mobile phone supports Bluetooth V2.1, password is not required.);
If pairing is failed, please turn off the headset first and then re-pair
according to steps 1～6 mentioned above.
After pairing is successful, the headset and the cell phone will remember
each other, they will no need to re-pair next time. The headset can
remember 8 paired devices, when the number of paired devices exceeds
8, the first one wi ll be replaced.
Every time the headset is turned on, not connected, press any button, it
will connect to last connected device automatically.
3
3) Pairing headset with a Bluetooth cell phone via NFC
BTH033L support NFC function, it can quickly connect with Bluetooth cell
phone via NFC, hereby take Samsung S3(Android 4.0) (Not included in
accessory) for example.
The general pairing procedures are as follows:
1) Please activate the Bluetooth and NFC function of cell phone;
Please refer to following pictures：
Remarks:
When the cell phone is in sleep or lock screen status, you can’t active
NFC function to connect.
Prior to pairing the headset for the first time, you need use your cell
phone to touch the NFC area until enter pairing mode.
When active the NFC function, try to make the cell phone and the
headset keep touch for longer. Otherwise it may fail to pair.
When the headset is disconnect (in standby mode), you can active NFC
function to fast connect. If the headset has connect, use your cell phone
to touch NFC zone, it will disconnect automatically.
4
Loading...