Zhongshan K mate General Electronics BTE004 User Manual

BTE004

Bluetooth mono headset

User Manual

 Brief introduction……………………………………….2

1. Bluetooth Wireless communication technology…………….2

2. About BTE004………………………………………………….2

 Before using……………………………………………..2

1. Overview…………………………………………………………2

2. Charging the battery of the headset………………………….3

 Basic operation…………………………………………..3

1. Switching on/off the headset……………………………………3

2. Pairing the headset with Bluetooth mobile phone…………….3

3. Wearing the headset……………………………………………..4

4. Changing the faceplate…………………………………………..5

5. The operation of the headset……………………………………6

6. LED indicator……………………………………………………..7

7. Indication tone…………………………………………………….7

 Care and maintenance……………………………………7
 Specification……………………………………………….8

Welcome to use this Bluetooth headset, BTE004. Please read this uer manual
carefully before using it.

 Brief introduction

1. Bluetooth Wireless communication technology

Bluetooth is a standard of close range radio communication technology that was

drawn up by Ericsson, IBM, Internet, Nokia and Toshiba. Through Bluetooth
technology, we can achieve the highest transmission rate among mobile phone,
computer, printer, PDA and other devices. The max transmit range of class 2 is 10
meters while the max radio-communication range of class 1 can reach up to 100
meters.

2. About BTE004

BTE004 is a Bluetooth headset. It has the following features:

 Answer call, end call and reject call
 Redial last call
 Voice dial (The function needs your mobile phone to support)
 Adjust volume
 Voice transfer
 Microphone mute
 The function of changing faceplate

 Before using

1. Overview

Multi-function button

1

(MFB)
Charging socket

2

LED indicator light

3

Microphone

4

Volume up

5

Volume down

6

Loudspeaker

7

Ear cap

8

Ear hook

9

2. Charging the bettary of the headset

First using—You must charge the battery of the headset fully before first using.
Low power—The red indicator light will flash and you can also hear 3 tones of “DU”
every 20 seconds. At this time, you have to charge the battery of the headset.

The charging steps are as follows:
Step1: Connect charger or charging cable to standard power outlet;
Step2: Connect the end of charger or charging cable to charging socket of the

headset;

Step3: When charging, red indicator light is on. It takes about 11.5 hours to

charge the battery fully;

Step4: When charging has completed, the red indicator light will switch off.

Note: If charging via a USB port, this USB port is used only for charging purposes, no

any data is transferred over the USB port.

Warning: 1. The battery is recycled.

2. Do not dispose of the battery in fire, as it may cause

Explosion.

 Basic operation

1. Switching on/off the headset

Function Operation

Switch on the
headset

Long press MFB for 3
seconds, and release it till

indicator light is on
Switch off the
headset

Long press MFB for 3

seconds, and release it till

indicator light is off





LED indicator
light

Blue indicator

5

light is on for 1
second

Red indicator

5

light is on for 1
second and

Indication tone

A long “DI” and a
long “DU” tones

A long “DI” tone

then all indicator

lights are off
Enter into
pairing mode

When the headset is off, long
press MFB for 78 seconds

Red and blue

LEDs flash

Nothing

alternately

Remark: The headset will switch off automatically if no devices can be connected after 10

minutes in order to save power.

2. Pairing the headset with Bluetooth mobile phone

You have to pair the Bluetooth headset with Bluetooth mobile phone before first using the
headset. Please make sure your mobile phone has bluetooth function that is available.
Specific pairing procedures may vary with different mobile phones. Please refer to your