Zhongshan K mate General Electronics BTC010 Users Manual
BTC010
Bluetooth hands-free kit
User’s manual
Brief introduction………………………………………………..1
1. Bluetooth wireless communication technology………………..…1
2. About BTC010...……………………………………………...…..1
Before use……………………………………………………..….2
1. Overview………………………………… ………………….……2
2. Charging the battery of BTC010………………………….………2
Getting started………….……………… ………………………..3
1. Switching on/off BTC010…..…….………….…………….……..3
2. Pairing BTC010 with a Bluetooth mobile phone..………....…..…4
3. Installation………………………………………..………….……4
4. Phone book…………………………………………………..……5
a) Prestoring phone number on to BTC010………………..….….5
b) Transferring phone number through Bluetooth………..……....5
c) Clearing pairing list……………………………………………6
5. Making a call with BTC010..……..….…………………………...6
6. Re-connecting with a Bluetooth device…………………………...7
7. Automatic switching off…………………………………………..8
8. LED Indicator …………….……..…………………………… ….8
9. Indication tone………………………………………………….…8
Care and maintenance………………………………….……..…9
FAQs……………………………………………………….…..….9
Specifications……………………………………………..…...…10
Welcome to use this Bluetooth hands-free kit, BTC010. Please read this
user’s manual carefully before use.
Brief introduction
1. Bluetooth wireless communication technology
Bluetooth is a standard of close range radio-communication technology that
was drawn up by Ericsson, IBM, Intel, Nokia and Toshiba. With Bluetooth
technology, we can achieve the highest transmission rate among mobile
phones, computers, printers, PDAs and other devices. The max transmission
range of class II is 10 meters while the max transmission range of class I can
reach up to 100 meters.
2. About BTC010
BTC010 is a portable Bluetooth hands-free kit. It adopts echo cancelling
technology and provides high-level sound quality. Meanwhile, it has simple
handsfree operation. It can pair with a Bluetooth cell phone or PDA
supporting HSP and HFP. It has the following features:
Answer a call, end a call and reject a call
Redial last number
Voice dial (This function needs to be supported by your mobile phone)
Adjust the volume
Call transfer between BTC010 and your mobile phone
Microphone mute
Caller ID memory
Transfer phone number to BTC010 from Bluetooth mobile phone
Dial prestored phone number
Remark: Even though the paired device and the hands-free kit support the
same Bluetooth profiles, functions may vary due to specification differences
of the paired devices.
1
Before use
1. Overview
Store phone number and
1
dial prestored phone
number
①①①①
Power on/Power
2
off/pair/end a call/reject
a call/cancel calling
3 Volume down 8 External microphone jack
4 Volume up 9 Charging jack
5 Built-in microphone 10 External microphone
2. Charging the battery of BTC010
The hands-free kit comes with a built-in rechargeable battery, prior to using
it, it is recommended to charge the battery fully for the first time.
Connect the charger to an standard power outlet and the charger plug to the
charging jack of the hands-free kit. The red LED is on while charging. It
takes about 2.5 hours to charge the battery fully. When charging has
completed, the red LED is off.
Store phone number and
6
dial prestored phone
number
②②②②
Answer a call/microphone
7
mute/call transfer/redial last
call
2
When the hands-free kit is on and the battery becomes low, the red LED
flashes 4 times every 30 seconds a nd the hands-free kit emits three “DU”
tones every 30 seconds. Please rec harge the battery fully as described above.
Remarks:
1) The battery will dry up if you don’t use BTC010 for a long time. If this
happens, you have to charge BTC010 for about 30 minutes before the
LED indicator will be on.
2) Please don’t attempt to take out the battery from BTC010, as this might
damage it.
Warning:
1) The battery is recycled.
2) Batteries (battery pack or batteries installed) shall not be exposed to
excessive heat place, such as sunshine, fire or the like.
Getting started
1. Switching on/off BTC010
Function Operation LED indicator
Switching on
BTC010
Switching off
BTC010
Entering
pairing mode
Remark: Pairing mode will last 2 minutes. If no devices can be connected
after 2 minutes, BTC010 will return to standby mode. If you want to repair,
please switch off BTC010 first and then enter pairing mode.
Press and hold button
for about 3～5 seconds until
hearing indication tone
Press and hold button
for about 3～5 seconds until
hearing indication tone
Make sure BTC010 is off,
then press and hold
button for 5～7 seconds
until red and blue LEDs flash
alternately
3
Blue LED of
button flashes five
times
Red LED of
button flashes 5
times
Red and blue LEDs
flash alternately
Loading...