Zhone PDN-4300-F1-600, PDN-4300-F1-610 Installation Instructions

Pole Mounting Kits for the 4300 6U Outdoor Cabinet

Models PDN-4300-F1-600 and PDN-4300-F1-610
Installation Instructions

Document Number 4300-A2-ZZ49-00

November 2005

Product Overview

The Model PDN-4300-F1-600 and PDN-4300-F1-610 Pole Mounting Kits are used for mounting the 4300 6U
Outdoor Cabinet to a solidly anchored and supported pole from the back of the cabinet. Model PDN-4300-F1-600 is
for a cabinet without a battery pedestal and PDN-4300-F1-610 is for a cabinet with a battery pedestal. See the
figures on the following pages for details.

The mounting bracket is constructed of heavy gauge steel with a powder coat painted finish for superior corrosion
resistance.

Inspecting Shipment

On receipt of the equipment:

• Inspect the shipping container(s) and note any signs of damage. Then unpack the container(s) and carefully

inspect for damage to the contents. If the equipment has been damaged in transit, immediately report the extent
of damage to the transportation company and to your sales representative. Order replacement equipment, if
necessary.

• Check the packing list to ensure complete and accurate shipment of all listed items. If the shipment is short or

irregular, contact your sales representative. If the equipment must be stored for a prolonged period, do so in the
equipment's original container. If equipment ever needs to be returned, please use the original packaging if
available.

Zhone Technologies
@Zhone Way
7001 Oakport Street
Oakland, CA 94621
USA

Copyright © 2005
Zhone Technologies, Inc.

4300-A2-ZZ49-00 November 2005 1

Pole Mounting Kits for the 4300 6U Outdoor Cabinet Installation Instructions

Pole Mounting – Cabinet without Pedestal

Use this procedure to mount the cabinet on a 6 to 8 inch diameter pole. See the figure below for a cabinet mounting
illustration.

Figure A - Pole Mounting Diagram (Cabinet without Pedestal)

2 November 2005 4300-A2-ZZ49-00

Pole Mounting Kits for the 4300 6U Outdoor Cabinet Installation Instructions

Table 1 - Pole Mounting without Pedestal

Item No. Qty Description

003 1 Bracket, Vertical Pole Mount, 10U/13U

006 1 Bracket, Lower Pole Mount, Access

009 1 Bracket, Upper Pole Mount

012 4 Nut, Nylon Top Lock 3/8"

015 14 Washer, 3/8" Stainless Steel, SAE, Flat

018 10 Screw, 3/8-16 x 1", Stainless Steel, Cap

021 6 Washer, Split Lock, 3/8 ZP

024 6 Washer, 3/8", Flat, Rubber

027 2 Bolt, Square Head, 5/8-11 x 16 & Nut, Galvanized

030 2 Washer, Curved, 2 1/4 x 2 1/4 x 3/16, 5/8, Galvanized

033 2 Nut, 5/8, Galvanized (Included with Bolt)

036 2 Washer, Square, 2 1/4 x 2 1/4 x 3/16, 5/8, Galvanized

Have the following equipment ready before beginning this procedure:

 One drill

 One 3/4” x 12” drill bit

 One 9/16” wrench

 Two 15/16” wrenches

 A pencil

 Model PDN-4300-F1-600 Pole Mounting Kit

Follow this procedure for pole mounting:

1. Pre-assemble the upper and lower horizontal brackets to the vertical bracket as shown in the above Figure.

2. Select a convenient mounting location on the pole.

3. Position the mounting bracket assembly against the pole and mark on the pole the location of the two (2) 5/8 “

bolts (item 27).

4. Place the mounting bracket assembly out of the way.

5. Drill two (2) 3/4” (19.05 mm) diameter holes completely through the pole at the locations marked in step 3.

6. Insert machine bolt (item 27) through mounting bracket and into the top mounting hole and press bolt and

bracket flush against the pole.

7. Place round-cupped washer (item 30), with the concave side in, on bolt and finger tighten nut.

8. Repeat step 6 for the remaining bolt.

9. Secure the mounting bracket assembly to the pole by securely tightening the machine bolts to 40 ft-lbs for

wooden posts and 100 ft-lbs for metal posts.

4300-A2-ZZ49-00 November 2005 3