This publication is protected by copyright law. No part of this publication may be copied or
distributed, transmitted, transcribed, stored in a retrieval system, or translated into any human or
computer language in any form or by any means, electronic, mechanical, magnetic, manual or
otherwise, or disclosed to third parties without the express written permission from Zhone
Technologies, Inc.
Bitstorm, EtherXtend, IMACS, MALC, MXK, Raptor, SLMS, Z-Edge, Zhone, ZMS, zNID and the
Zhone logo are trademarks of Zhone Technologies, Inc.
Zhone Technologies makes no representation or warranties with respect to the contents here of
and specifically disclaim any implied warranties of merchantability, non infringement, or fitness for
a particular purpose. Further, Zhone Technologies reserves the right to revise this publi cation and
to make changes from time to time in the contents hereof without obligation of Zhone
Technologies to notify any person of such revision or changes.
This product may contain copyrighted software that is licensed under the GNU General Public
License (“GPL”), a copy of which is available at www.gnu.org/licenses. You may obtain a copy of
such software, in source code form, from Zhone for a period of three years after our last shipment
of the product by following the instructions at www.zhone.com/gplinfo.
65xx-A1 Family Router Users Guide 2
Important Safety Instructions
1. Read and follow all warning notices and instructions marked on the product or included in the
manual.
2. Slots and openings in the housing are provided for ventilation. To ensure reliable operation of
the product and to protect it from overheating, these slots and openings must not be blocked or
covered.
3. Do not allow anything to rest on the power cord and do not locate the product where persons
will walk on the power cord.
4. Do not attempt to service this product yourself, as opening or removing covers may expose you
to dangerous high voltage points or other risks. Refer all servicing to qualified service
personnel.
5. General purpose cables are used with this product for connection to the network. Special
cables, which may be required by the regulatory inspection authority for the installation site, are
the responsibility of the customer. Use a UL Listed, CSA certified, minimum No. 24 AWG line
cord for connection to the Digital Subscriber Line (DSL) network.
6. When installed in the final configuration, the product must comply with the applicable Safety
Standards and regulatory requirements of the country in which it is installed. If necessary,
consult with the appropriate regulatory agencies and inspection authorities to ensure
compliance.
7. A rare phenomenon can create a voltage potential between the earth grounds of two or more
buildings. If products installed in separate buildings are interconnected, the voltage potential
may cause a hazardous condition. Consult a qualified electrical consultant to determine
whether or not this phenomenon exists and, if necessary, implement corrective action prior to
interconnecting the products.
8. Input power to this product must be provided by one of the following: (1) a UL Listed/CSA
certified power source with a Class 2 or Limited Power Source (LPS) output for use in North
America, or (2) a certified transformer, with a Safety Extra Low Voltage (SELV) output having a
maximum of 240 VA available, for use in the country of installation.
9. In addition, since the equipment is to be used with telecommunications circuits, take the
following precautions:
— Never install telephone wiring during a lightning storm.
— Never install telephone jacks in wet locations unless the jack is specifically designed for wet
locations.
— Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
— Use caution when installing or modifying telephone lines.
— Avoid using a telephone (other than a cordless type) during an electrical storm. There may
be a remote risk of electric shock from lightning.
— Do not use the telephone to report a gas leak which is in the vicinity of the leak.
65xx-A1 Family Router Users Guide 3
CE Marking
When the product is marked with the CE mark on the equipment label, a supporting De claration
of Conformity may be downloaded from the Zhone World Wide Web site at www.zhone.com.
FCC Part 15 Declaration
An FCC Declaration of Conformity may be downloaded from the Zhone World Wide Web site at
www.zhone.com.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
The authority to operate this equipment is conditioned by the requirement that no modifications
will be made to the equipment unless the changes or modifications are expressly approved by the
responsible party.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
— Consult the dealer or an experienced radio/TV technician for help.
Notice to Users of the United States Telephone Network
The following notice applies to versions of the modem that have been FCC Part 68 approved.
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the
Administrative Council for Terminal Attachment (ACTA). On the bottom side of this equipment is a
label that contains, among other information, a product identifier in the format
US:AAAEQ##TXXXX. If requested, this number must be provided to the Telephone Company.
This equipment is intended to connect to the Public Switched Telephone Network through a
Universal Service Order Code (USOC) type RJ11C jack. A plug and jack used to connect this
equipment to the premises wiring and telephone network must comply with the applicable FCC
Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular
plug is provided with this product. It has been designed to be connected to a compatible modular
jack that is also compliant.
The Ringer Equivalence Number (REN) is used to determine the number of devices that may be
connected to a telephone line. Excessive RENs on a telephone line may result in the devices not
ringing in response to an incoming call. In most but not all areas, the sum of RENs should not
65xx-A1 Family Router Users Guide 4
exceed five (5.0). To be certain of the number of devices that may be connected to a line, as
determined by the total RENs, contact the local Telephone Company.
The REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX.
The digits represented by ## are the REN without a decimal point. For example, 03 represents a
REN of 0.3.
If the modem causes harm to the telephone network, the Telephone Company will notify you in
advance that temporary discontinuance of service may be required. But if advance notice is not
practical, the Telephone Company will notify the customer as soon as possible. Also, you will be
advised of your right to file a complaint with the FCC if you believe it is necessary.
The Telephone Company may make changes in its facilities, equipment, operations or
procedures that could affect the operation of the equipment. If this happens, the Telephone
Company will provide advance notice in order for you to make necessary modifications to
maintain uninterrupted service. If trouble is experienced with the modem, refer to the repair and
warranty information in this document.
If the equipment is causing harm to the telephone network, the Telephone Company may request
that you disconnect the equipment until the problem is resolved.
The user may make no repairs to the equipment.
Connection to party line service is subject to state tariffs. Contact the state public utility
commission, public service commission or corporation commission for information.
If the site has specially wired alarm equipment connected to the telephone line, ensure the
installation of the modem does not disable the alarm equipment. If you have questions about
what will disable alarm equipment, consult your Telephone Company or a qualified installer.
Notice to Users of the Canadian Telephone Network
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical
Specifications. This is confirmed by the registration number. The abbreviation IC before the
registration number signifies that registration was performed based on a Declaration of
Conformity indicating that Industry Canada technical specifications were met. It does not imply
that Industry Canada approved the equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is labelled on the
equipment. The REN assigned to each terminal piece of equipment provides an indication of the
maximum number of terminals allowed to be connected to a telephone interface. The terminati on
on an interface may consist of any combination of devices subject only to the requirement that the
sum of the Ringer Equivalence Numbers of all the devices does not exceed five.
If your equipment is in need of repair, contact your local sales representative, service
representative, or distributor directly.
NOTICE: This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de classe B est conforme à la norme Canadienne NMB-003.
65xx-A1 Family Router Users Guide 5
!
CANADA - EMI NOTICE:
This Class B digital apparatus meets all requirements of the Canadian interferen ce-causing
equipment regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du règlement sur le matérial
brouilleur du Canada.
NOTICE: This device complies with RSS-210,IC ID:8609A-1518A1NA
Operation is subject to the following two conditions:
1) This device may not cause interference and
2) This device must accept any interference, including interference that may cause undesired
operation of the device.
65xx-A1 Family Router Users Guide 6
Table of Contents
Important Safety Instructions................................................................................................................................3
CE Marking ......................................................................................................................................................4
FCC Part 15 Declaration..................................................................................................................................4
Table of Contents .................................................................................................................................................7
About This Guide................................................................................................................................................10
Style and Notation Conventions.....................................................................................................................10
Contacting Customer Service and Technical Support........................................................................................12
Chapter 1 Introduction 13
System Requirements........................................................................................................................................13
Front Panels.......................................................................................................................................................14
6519-X1 Front Panel......................................................................................................................................14
6518-A1 Front Panel......................................................................................................................................14
6512-A1 Front Panel......................................................................................................................................14
6511-A1 Front Panel......................................................................................................................................15
LED descriptions............................................................................................................................................15
Back Panel .........................................................................................................................................................16
Connecting Your Hardware ................................................................................................................................17
Mounting the Router...........................................................................................................................................18
Unit dimensions .............................................................................................................................................19
Configuring Your Computer................................................................................................................................20
Windows 2000 ...............................................................................................................................................20
Windows XP...................................................................................................................................................21
Windows 7......................................................................................................................................................21
Chapter 3 The Web User Interface 22
Log in to the Router............................................................................................................................................22
LAN Statistics.................................................................................................................................................24
WAN Statistics................................................................................................................................................25
ADSL BER Test..............................................................................................................................................26
Add an ATM Layer 2 Interface .......................................................................................................................39
Add an Ethernet Layer 2 Interface.................................................................................................................40
Add a Bridge WAN Service............................................................................................................................41
Add a PPPoE WAN Service...........................................................................................................................41
Add an IPoE WAN Service ............................................................................................................................43
Add a PPPoA WAN Service...........................................................................................................................45
Add an IPoA WAN Service.............................................................................................................................46
Remove a Connection ...................................................................................................................................49
Edit a Connection...........................................................................................................................................49
Port Triggering ...............................................................................................................................................53
IP Filtering—Outgoing....................................................................................................................................55
IP Filtering—Incoming....................................................................................................................................56
MAC Filtering .................................................................................................................................................59
Parental Control .................................................................................................................................................61
Time Restriction.............................................................................................................................................61
Quality of Service...............................................................................................................................................64
DNS Proxy..........................................................................................................................................................77
Print Server (6519 ONLY)..................................................................................................................................78
Adding a printer server...................................................................................................................................78
Windows 7.................................................................................................................................................79
Windows XP ..............................................................................................................................................83
LAN Ports...........................................................................................................................................................91
MAC Filter....................................................................................................................................................112
Station Info...................................................................................................................................................119
System Log ......................................................................................................................................................124
Configure System Log .................................................................................................................................125
Internet Time ....................................................................................................................................................128
Access Control .................................................................................................................................................129
IP Addresses....................................................................................................................................................131
The Router Is Not Functional ...........................................................................................................................136
You Cannot Connect to the Router ..................................................................................................................136
The DSL LED Continues to Blink.....................................................................................................................136
The DSL LED is Always Off..............................................................................................................................137
The Internet LED is Always Off ........................................................................................................................137
Diagnosing Problems using IP Utilities ............................................................................................................137
This guide is intended for use by installation technicians, system administrators, and network
administrators. It explains how to install and configure the 6511-A1, 6512-A1 6518-A1, and 6519X1 routers.
Style and Notation Conventions
The following conventions are used in this document to alert users to information that is
instructional, warns of potential damage to system equipment or data, and warns of potential
injury or death. Carefully read and follow the instructions included in this document.
Caution: A caution alerts users to conditions or actions that could damage equipment or data.
Note: A note provide s im portant supplemental or amplified information.
Tip: A tip provides additional information that enables users to more readily complete their tasks.
WARNING! A warning alerts users to conditions or actions that could lead to injury or death.
65xx-A1 Family Router Users Guide 10
Typographical Conventions
The following typographical styles are used in this guide to represent specific types of
information.
Bold
Fixed
Fixed Bold
Fixed Bold
Italic
Italic
PLAIN UPPER
CASE
Command Syntax
Used for names of buttons, dialog boxes, icons, menus,
profiles when placed in body text, and property pages (or
sheets). Also used for commands, options, parameters in
body text, and user input in body text.
Used in code examples for computer output, file names, path
names, and the contents of online files or directories.
Used in code examples for text typed by users.
Used in code examples for variable text typed by users.
Used for book titles, chapter titles, file path names, notes in
body text requiring special attention, section titles,
emphasized terms, and variables.
Used for environment variables.
Brackets [ ] indicate optional syntax.
Vertical bar | indicates the OR symbol.
Acronyms
The following acronyms are related to Zhone products and may appear through out this manual:
Table 1: Acronyms and their descriptions
Acronym Description
ADSL Asymmetrical Digital Subscriber Line
AP Access Point
ACS Auto Configuration Server
DHCP Dynamic Host Configuration Protocol
DSL Digital Subscriber Line
EFM Ethernet in the First Mile
MALC Multi-Access Line Concentrator
MIB Management Information Bases
NAT Network Address Translation
NMS Network Management System
65xx-A1 Family Router Users Guide 11
PVC Permanent Virtual Circuit
RADIUS Remote Authentication Dial In User Service
SHDSL Symmetric High-bit-rate Digital Subscriber Line
SLMS Single Line Multi-Service
SNMP Simple Network Management Protocol
TFTP Trivial File Transfer Protocol
VoIP Voice over IP
VPN Virtual Private Network
WEP Wired Equivalent Privacy
Wi-Fi Wireless Fidelity (IEEE 802.11 wireless networking)
WMM Wi-Fi Multimedia
WPA Wi-Fi Protected Access
ZMS Zhone Management System
Contacting Customer Service and Technical Support
Customer service and technical support for this Zhone device are provided by your Internet
Service Provider.
65xx-A1 Family Router Users Guide 12
Chapter 1 Introduction
The 6519-X1 (four port N 2X2 router with WiFi), 6518-A1 (four port N router with WiFi), 6512-A1
(four port), and 6511-A1 (one port) ADSL 2+ routers are easily installed routers whi ch deliver the
performance needed for multimedia applications
This User’s Guide will show you how to set up the routers, and how to customize the
configuration to get the most out of the product.
The 65xx-A1 family provides the following features:
• ADSL2+ modem which supports ANSI T1.413 ISSUE 2, ITU G.992.1 (G.DMT), ITU G.992.2
(G.LITE), ITU G992.3, ITU G992.5, and ADSL2+ to meet different linking speeds from your
ISP.
• 802.11 b/g WiFi LAN port (6519/6518 only).
• DSL Dying Gasp support.
• Four 10/100BaseT Ethernet ports to provide Internet connectivity to all computers on your
LAN (6518 and 6512) The 6511 has one 10/100BaseT Ethernet port.
• Easy-to-use configuration program accessible through a standard web browser.
System Requirements
In order to use your 65xx-A1 family ADSL router for Internet access, you must have the following:
• ADSL service subscription from your ISP.
• A PC with:
An Ethernet 10/100BaseT network interface card
A processor equivalent to or faster than a Pentium II 133 MHz
32 MB RAM or greater
Windows 95b, 98, 98SE, 2000, ME, NT, XP, Vista or Windows 7. (Note: Windows 95
requires the installation of the Winsock program, not included.)
•(Optional) An Ethernet hub or switch, if you are connecting the device to several computers
on an Ethernet network.
•For system monitoring or configuration using the supplied web interface, a web browser such
as Internet Explorer Version 6.0 or later. Netscape is not supported.
Package Contents
In addition to this document, your package should arrive containing the following:
• 6519-X 1, 6518-A1, 6512-A1, or 6511-A1 ADSL 2+ router
• 12V 700 mA power adapter
• RJ-11 telephone cable
• RJ-45 Ethernet cable
• User Manual / Quick Guide
Safety Instructions
Place your modem on a flat surface close to the cables in a location with sufficient ventilation.
65xx-A1 Family Router Users Guide 13
To prevent overheating, do not obstruct the ventilation openings of the device.
Plug the device into a surge protector to reduce the risk of damage from power surges and
lightning strikes.
Operate this equipment only from an electrical outlet with the correct power source as indicated
on the adapter.
Do not open the cover of the device. Opening the cover will void any warranties on the
equipment.
Unplug equipment first before cleaning. A damp cloth can be used to clean the equipment. Do not
use liquid / aerosol cleaners or magnetic / static cleaning devices.
Front Panels
6519-X1 Front Panel
6518-A1 Front Panel
6512-A1 Front Panel
65xx-A1 Family Router Users Guide 14
6511-A1 Front Panel
LED descriptions
LED Mode INDICATION
Power
DSL
Internet
LAN 1-4
(6511 has one
LAN port)
Wireless
(6518/6519
only)
USB (6519
only)
WLAN
(6518/6519
only)
WPS
(6518/6519
only)
Solid green Boot-up successful
Solid red Router is booting up
The router may not be turned on. Check if the power adapter is
No light
Solid
Flashing The router is attempting to connect to your ISP
Solid ADSL is connected
No light ADSL is not connected. The ALARM LED will be red
Blinking The router is connected to the LAN
Solid on
green
Flashing The router is sending or receiving data over Ethernet
Off No LAN Link
Solid Wireless is enabled
No light Wireless is disabled
Blinking Wireless traffic activity
Solid
Blinking Data transfer over USB
Solid WLAN Wireless is enabled
No light
Blinking Wireless traffic activity
No light
Blinking WPS key has been pressed and key exchange is in progress.
connected to the modem, the modem is plugged in and the power
switch button is in the on (pushed in) state.
Connection established. The router is able to communicate with
your ISP via ADSL
Ethernet interface is successfully connected to a device through
the LAN port
USB device is connected
Wireless is disabled
WPS not active.
NOTE: The 6512 and 6511 do not have the wireless LED. The 6511 has one LAN LED.
65xx-A1 Family Router Users Guide 15
Back Panel
NOTE: The below port descriptions are listed as they appear on the back panel from left to right.
Port Description
DSL
LAN1 – LAN4
Reset / Default
Power
Switch
RJ-11 cable connects to incoming DSL line
RJ-45 connects the unit to an Ethernet device such as a PC or a
switch.
Restart—press the button for less than 4 seconds.
ISP settings—press the button for 4 seconds or longer.
Factor y Default settings – press the button for 60 seconds or
longer
Connects to a 12V 700 mA power adapter.
Power on (depressed) or power off for the router.
NOTE: The 6512 and 6511 do not have the wireless antenna. The 6511 has one LAN port.
65xx-A1 Family Router Users Guide 16
Chapter 2 Hardware Installation and PC Setup
Overview
This chapter provides basic instructions for connecting the router to a computer or a LAN and to
the Internet using DSL. The first part provides instructions to set up the hardware, and the second
part describes how to prepare your PC for use with the router. Refer to Chapter 3, Using the Web
Interface for configuration instructions.
It is assumed that you have already subscribed to DSL service with your telephone company or
other Internet service provider (ISP).
Connecting Your Hardware
Shut down your PC before connecting the router. To connect your modem:
1. Connect the ADSL Line
Connect one end of an RJ-11 cable from your ADSL connection and the other end to the
LINE port of the modem.
2. Connect the PC to the Router
To use the Ethernet connection, connect the Ethernet cable from the computer directly to the
router. Connect one end of the Ethernet cable to one of the four ports labelled LAN on the
back of the router and attach the other end to the Ethernet port of your computer.
65xx-A1 Family Router Users Guide 17
3. Connect the Power Adapter
Complete the process by connecting the AC power adapter to the POWER connector on the
back of the device and plug the adapter into a wall outlet or power strip. Then turn on and
boot up your PC and any LAN devices, such as hubs or switches, and any computers
connected to them.
Mounting the Router
The router can be mounted on the wall with two screws. Mounting can be done on wall material
including concrete, wood, or drywall. Select an appropriate location free from obstructions or any
possible interference. Make sure the cables can be easily attached to the router without strain.
The illustration below shows how to mount the router horizontally on a wall.
NOTE: Mount the router with the cables facing down, the LEDs facing up.
65xx-A1 Family Router Users Guide 18
Unit dimensions
Model Unit Dimensions Mounting Holes
1.30" (H) x 7.25" (W) x 5" (D)
6511-A1
6512-A1
6518-A1
65xx-A1 Family Router Users Guide 19
34.93 mm (H) x 184.15mm (W) x 127mm
(D)
1.25"(H) x 8.25" (W) x 4.75" (D)
31.75 mm (H) x 209.55 mm (W) x 102.65
mm (D)
1.25" (H) x 8.25" (W) x 4.75" (D)
31.75 mm (H) x 209.55 mm (W) x 102.65(D)
2 holes- 5.375" (136.63mm)
apart
2 holes 6.125" (155.58mm)
apart
2 holes 6.125" (155.58mm) apart
Model Unit Dimensions Mounting Holes
1.25" (H) x 8.25" (W) x 4.75" (D)
6519-X1
31.75 mm (H) x 209.55 mm (W) x 102.65(D)
Configuring Your Computer
Prior to accessing the router through the LAN or the USB port, note the following necessary
configurations—
•Your PC’s TCP/IP address: 192.168.1.__( the last number is any number between 2 and
254)
• The router’s default IP address: 192.168.1.1
• Subnet mask: 255.255.255.0
Below are the procedures for configuring your computer. Follow the instructions for the operating
system that you are using.
If you used the Ethernet cable to connect your router and PC, you do not need any specific driver
installation.
2 holes 6.125" (155.58mm) apart
Windows 2000
1. In the Windows taskbar, click the Start button and point to Settings, Control Panel, and
2. Click Local Area Connection. When you have the Local Area Connection Status window
3. Listed in the window are the installed network components. If the list includes Internet
4. If Internet Protocol (TCP/IP) does not appear as an installed component, then click Install.
5. In the Select Network Component Type window, click on protocol and then the Add
6. Select Internet Protocol (TCP/IP) from the list and then click on OK.
7. If prompted to restart your computer with the new settings, click OK.
8. After your computer restarts, click the Network and Dial-up Connections icon again, and
9. In the Local Area Connection Properties dialog box, select Internet Protocol (TCP/IP)
Network and Dial-up Connections (in that order).
open, click Properties.
Protocol (TCP/IP), then the protocol has already been enabled, and you can skip to Step
10.
button.
right click on the Local Area Connection icon and then select Properties.
and then click Properties.
10. In the Internet Protocol (TCP/IP) Properties dialog box, click the radio button labelled Use
the following IP address and type 192.168.1.x (where x is any number between 2 and 254)
and 255.255.255.0 in the IP address field and Subnet Mask field.
11. Click OK twice to save your changes and then close the Control Panel.
65xx-A1 Family Router Users Guide 20
Windows XP
Windows 7
1. In the Windows taskbar, click the Start button and point to Settings and then click Network
Connections.
2. In the Network Connections window, right click on the Local Area Connection icon and
click on Properties.
3. Listed in the Local Area Connection window are the installed network components. Make
sure the box for Internet Protocol (TCP/IP) is checked and then click Properties.
4. In the Internet Protocol (TCP/IP) Properties dialog box, click the radio button labelled Use
the following IP address and type 192.168.1.x (where x is any number between 2 and 254)
and 255.255.255.0 in the IP address field and Subnet Mask field.
5. Click OK twice to save your changes and then close the Control Panel.
1. In the Windows taskbar, click the Start button and point to Control Panel and then click
Network and Internet.
2. In the Network and Internet window, click Network and Sharing Cen ter.
3. In the left panel click Change adapter settings.
4. In the Network Connections screen, right click Local Area Connection and select
Properties.
5. Listed in the Local Area Connection window are the installed network components. Select
Internet Protocol Version 4 (TCP/IP v4) is checked and then click Properties.
6. In the Internet Protocol Version 4 (TCP/IP v4) dialog box, click the radio button labelled
Use the following IP address and type 192.168.1.x (where x is any number between 2 and
254) and 255.255.255.0 in the IP address field and Subnet Mask field.
7. Click OK the Close to save your changes and then close the Control Panel.
65xx-A1 Family Router Users Guide 21
Chapter 3 The Web User Interface
The 65xx-A1 family of combination modem/routers have a Wide Area Network (WAN) connection
which connects to your phone line. This connects to your Internet Service Provider (ISP) via the
phone line. The Local Area Network (LAN) connections are where you plug in your local
computers to the router. The 6518-A1 also has a wireless interface. The router is normally
configured to automatically provide all the PCs on your network with Internet addresses.
Your router may be pre-configured with your ISP configuration to ease your installation. Please
contact your ISP if you need information on how to connect the modem to your ISP. To set up
your router with a basic configuration required by your service provider, you can use the Quick
Setup form the top of the navigation bar. In order for this to work, all other WAN services must
first be removed. To remove services, from the top navigation bar select Quick Setup.
If you connected a PC (rather than a hu b or a switch) directly to the router, your LAN consists of that PC. You
may also create connections for various protocol options by creating new connections.
To configure your router you will first need to log in to the router.
Note: Before configuring your router, make sure you have followed the instructions in Chapter 2
Hardware Installation and PC Setup. You should have your PCs configured for DHCP mode (if
your router will be), and have proxies disabled on your browser. If you see a login redirection
screen when you access the web interface, verify that JavaScript support is enabled in your
browser. Also, if you do not get the screen shown below, you may need to delete your temporary
Internet files.
Log in to the Router
This section will explain how to log in to your router.
1. Launch your web browser.
2. Enter the URL http://192.168.1.1
A login screen like the one below will be displayed after you connect to the user interface.
in the address bar and press Enter.
15xx-A1 Family Router Users Guide 22
Note: There are three default user name and password combinations; Admin, Support, and User. The
user / user name and password combination can display device st atus, but cannot change or save
configurations. The admin / admin combination can perform all functions. Passwords can be chang ed at
any time.
For information about password administration, see Passwords on page 130.
Summary
3. Enter your user name and password, and then click on OK to display the user interface. The user name / password are admin / admin and both are case sensitive.
Note: For security reasons you should change your password as soon as possible.
Access the general information of the router by clicking Summary under Device Info. This
screen shows details of the router such as the version of the software, bootloader, LAN IP
address, etc. It also displays the current status of your DSL connection as shown below.
65xx-A1 Family Router Users Guide 23
WAN
Display the WAN status report from the router by clicking WAN under Device Info. The graphic
below shows the screen when a WAN connection is set up.
LAN Statistics
Display LAN statistics by clicking LAN under Statistics
65xx-A1 Family Router Users Guide 24
WAN Statistics
Display WAN statistics by clicking WAN Service under Statistics.
xTM Statistics
Display ATM statistics by clicking xTM under Statistics.
65xx-A1 Family Router Users Guide 25
xDSL Statistics
Display ADSL statistics by clicking xDSL under Statistics. Information contained in this screen is
useful for troubleshooting and diagnostics of connection problems.
ADSL BER Test
The ADSL Bit Error Rate (BER) test determines the quality of the ADSL connection. The test is
performed by transferring idle cells containing a known pattern and comparing the received data
with this known pattern to check for any errors The BER Test reflects the ratio of error bits to the
total number transmitted.
65xx-A1 Family Router Users Guide 26
If you click on the ADSL BER Test button at the bottom of the ADSL Statistics page, the following
pop-up screen will appear allowing you to set the tested time and to begin the test.
To run a BER test:
1. On the bottom of the xDSL statistics page, click xDSL BER Test
2. In the Tested Time (sec) drop down, select the test duration, and then click Start.
Route
3. Check the results.
Access the routing status report from the router by clicking Route under Device Info.
65xx-A1 Family Router Users Guide 27
ARP
Display the ARP status report by clicking ARP under Device Info.
DHCP
ARP (Address Resolution Protocol) maps the IP address to the physical address, labelled HW
Address (the MAC address) and identifies computers on the LAN.
Display the DHCP lease information by clicking DHCP under Device Info.
DHCP (Dynamic Host Control Protocol) allows the modem to automatically assign IP addresses,
to connected devices. By default, your modem is set up to assign devices addresses from
192.168.1.2 to 192.168.1.254.
65xx-A1 Family Router Users Guide 28
65xx-A1 Family Router Users Guide 29
Loading...
+ 115 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.