18650 Li-ion Battery × 2 18650 Battery Charger × 1 Camera Backing Base × 1
Micro USB Cable × 1
Type-C Adapter × 1
Type-C USB Firmware
Upgrade Cable × 1
USB Cable
Storage Box × 1
Micro USB
Camera Control Cable × 1
Storage Case × 1
1
Get to Know WEEBILL LAB
1
Get to Know WEEBILL LAB
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
1. Camera Control Interface
2. Thumb Screw
3. Follow Focus Control Interface
4. Quick Release Button
5. Lens Support
6. Quick Release Lock Screw
7. Safety Lock
8. Pan Axis Motor
9. Thumb Screw
10. Focus/Zoom Control Wheel
11. 1/4" Screw Thread with Crown
Gear
12. Side Buttons (see more on Page
10 )
13. Tripod
14. Tilt Axis Motor
15. Tilt Axis Latch
16. Camera Control Module
17. Roll Axis Motor
18. Roll Axis Latch
19. Pan Axis Latch
20. Battery Compartment
21. Firmware Upgrade Interface
22. Control Panel (see more on Page
10 )
2
Preparing and Charging the Batteries
When using WEEBILL LAB for the first time, please fully charge and activate
the batteries with the dedicated charging device contained in the package to
ensure normal use of the product.
1. The stabilizer is equipped with high-energy density batteries, which
may cause fire, economic loss or personal injury when not properly used
and stored. Please read the disclaimer and warning herein as well as the
description on the battery label carefully before using the batteries.
2. Please use batteries provided or approved by ZHIYUN only. ZHIYUN will
not take any responsibility for explosion, fire and/or accidents caused by
non-ZHIYUN batteries.
When the batteries are not in use, please be sure to put them in the
battery slot of the package or in plastic storage cases (the storage case
needs to be purchased separately).
3
Preparing and Charging the Batteries
Charging Procedure
1. Insert the batteries into the charger in the right direction (positive/negative
end) accordingly.
2. Connect the charger to the adapter via the Micro USB cable.
3. Plug the adapter into an USB power outlet to start charging.
USB CableAdapter
1. Battery charging may fail when the power supply is insufficient (for
instance, when the current of the adapter is lower than 500mA).
Conditions may vary depending on the specific chargers used. It is
recommended to use an adapter with higher current capacity.
2. The battery cannot be charged through the USB port on the stabilizer.
1. Please use qualified standard 5V/≥2000mA adapter for battery charging;
charging time depends on the maximum input current of the adapter.
2. This stabilizer comes standard with two high-discharge-rate dedicated
batteries. Please use and charge batteries provided or approved by
ZHIYUN only.
3. Please make sure both the batteries are fully charged. Either battery
under charged can lead to failure of the stabilizer.
Power Supply
4
Installation
Each axis of the gimbal is equipped with a latch. You can use these latches to
lock the axes for convenient installation and storage.
Locked for
installation
Locked for
storage
Tripod Installation
Get the tripod ready and mount it to the 1/4"-3/8" threaded hole at the
bottom of the stabilizer, then unfold the tripod on a flat surface.
You can also install the tripod onto the base of battery compartment to enter
Sling Mode.
Be sure to put the tripod lock switch to lock position before entering into
Sling Mode.
5
Installation
Battery Installation
Slide out the cover of the battery compartment
and load two ZHIYUN 18650 lithium batteries
(note the positive and negative directions).
Camera Installation
a. Take out the quick release plate module and press the Quick Release Button
to take out the Arca quick release plate.
b. Mount the camera on the backing base as above, then mount it on the
quick release plate and tighten the 1/4’’ screw at its bottom.
c. Adjust the lens support on the quick release plate to support the lens and
ensure it is stable.
d. Mount the installed quick release plate into the quick release module, and
then install and lock the whole module on the three-axis stabilizer.
1. Before mounting the camera, make sure it is prepared ahead of time.
Remove the lens cap and make sure the camera’s battery and memory
card are already in place.
2. The backing base is needed when the size of the lens outranges the
bottom of the camera. You can decide whether to install the backing
base according to the actual situation.
6
Installation
Camera Control Cable Connection
Connect the two ends of the camera control cable included in the package to
the control interface of the camera and stabilizer.
Interface TypeMicro USBTpye-C
Camera ModelSonyα6300Panasonic GH5
Photo√√
Video√√
AV√√
TV√√
ISO√√
EV√√
Image Transmission√√
1. If the camera uses type-c interface control, please connect with the
type-c adapter included in the package.
2. The list above is based on Sony a6300 and Panasonic GH5. For
compatibility with other cameras, please refer to our official website or
consult customer service.
3. Please charge the camera through the camera control interface. If
your camera has sufficient power and does not require direct charging
with the stabilizer, please turn off the USB power supply option of the
camera to save power of the stabilizer.
7
Balance Adjustment
Balance Adjustment
To facilitate the adjustment procedure, we recommend locking the three
axes of WEEBILL LAB the way as camera-mounted state, then unlock and
make balance adjustment of the axes one by one.
❶
Unlock the tilt axis and the camera locking
latch, push the camera to move forward or
backward until the camera can stay still and
almost level with its lens facing front (as
shown on the right). Complete this step by
tightening up the camera mounting thumb
screw.
Push the safety lock up if it stucks.
❷
Make the lens face up, slightly loosen the
thumb screw of the tilt axis, push the camera
to move upward or downward until the
camera can stay still with the lens facing up
(i.e.the camera stays still and vertical to the
ground as shown on the right). Complete this
step by tightening up the thumb screw.
❸
Unlock the roll axis, slightly loosen the
thumb screw at the bottom of the quick
release plate, push the camera to move left
or right until the camera can stay still and
horizontal to the ground (as shown on the
right). Complete this step by tightening up
thumb screw.
8
Balance Adjustment
❹
Unlock the pan axis, slightly loosen the
thumb screw on it, then adjust the pan axis
until it stays still and horizontal to the ground
(as shown on the right). Complete this step by
tightening up thumb screw.
If the camera hinders rotation of
any screw, please pull up and turn
round the screw, then rotate again
to tighten up.
Before turning on the stabilizer, make sure the three motors are unlocked
and can move freely. Turning on the stabilizer in locked state will lead to
overheating and damage of the motors.
9
How to Use
Buttons Description
1
2
3
4
5
6
❶
Focus/Zoom Control Wheel*
Once connected to the servo follow focus motor, the focus/zoom control wheel
on the gimbal will be able to drive the follow focus motor.
❷
Following Mode
• Press to enter into F (Following) Mode
• Double press to reset the motor position
• Triple press to realize 180° rotation on pan axis motor
❸
PhoneGo Mode[
Press the GO button to enter PhoneGo Mode which enables faster following
speed of the three axes on the stabilizer.
❹
Mode Switch
• Dial up and the stabilizer enters into PF (Pan Following) Mode.
• Dial down the stabilizer enters into L (Locking) Mode.
❺
POV Mode [
• Single press to enter or exit POV (Point of View) Mode.
• Double press to enter or exit V (Vortex) Mode
• Long press for 2 seconds to enter or exit standby Mode.
❻
ON/OFF [ ]
Long press for 2 seconds to power on/off the stabilizer.
❼
OLED Display
POV
GO
]
]
Stabilizer status and camera parameters (see more on Page 12 )
7
8
10
11
15
9
12
14
13
*When the stabilizer is properly installed with the follow focus CMF-04 (needs
to be purchased separately), the focus or zoom control function can be
achieved by installing the gear ring on either the focus or zoom channel of the
lens. WEEBILL LAB does not support synchronous zoom & focus control.
10
How to Use
❽
Joystick
Four-way direction control of the camera/lens on the stabilizer.
❾
Video [ ]
Single press to start/end video recording.
❿
Reserved functional button[
Reserved functional button
⓫
Right[ ► ]
• In main screen, single press to move to next option.
• In menu screen, single press to confirm selection.
⓬
Dial
• In main screen, rotate the dial to adjust camera parameters.
• In menu screen, rotate the dial to switch between options.
●●●
⓭
Menu[
]
Single press to enter or exit menu screen.
⓮
• Halfway press the button to activate auto focus.
• Full press the button to take single shots.
⓯
• In main screen, single press to move to previous option.
• In menu screen, single press to return to previous screen.
Shutter Release
Left [ ◄ ]
1. When powering on the stabilizer, please loose hold the camera with
one hand in case of malfunctioned rotation.
2. When powering on, avoid shaking of the stabilizer which may lead to
start-up failure.
]
LV
11
How to Use
OLED Screen Interface Description
Display screen with
camera params settings
Icon Description :
Camera Connection Status
Video Mode
Photo Mode
Battery Level (stabilizer)
Pan Following Mode
PF
Locking Mode
L
F
V
AV
TV
Point Of View Mode
Following Mode
PhoneGo Mode
Vortex Mode
Aperture Value
Shutter Speed Value
ISO
EV
POV
GO
ISO
Display screen with
stabilizer modes
(camera params
settings unavailable)
Menu Screen
12
How to Use
motor
(Motor Torque
Setting)
wheel
(Control Wheel
Setting)
joystick
(Joystick Setting )
calibration
(Calibration
Setting)
angle
(Fine-tuning on
motor angle)
about
Menu Option Description
lowLow-torque
mediumMedium-torque
highHigh-torque
sensi
(control wheel
sensitivity)
ABpoint
(AB Point)
priority
(Priority on
Wheel)
reverse
(Reverse)
reverse
(Reverse)
yesEnter six-side calibration
noExit calibration setting
pitchFine tune the tilt axis motor
rollFine tune the roll axis motor
Information of firmware versions, WIFI and name of
Bluetooth (press right to find out which version of image
transmission system the stabilizer is running)
low
medium
high
A
Max
B
clearClear AB Points
1
Lite
A
B
Low Sensitivity
Medium sensitivity
High Sensitivity
Set the current wheel position
as A point
Set the current wheel position
as B point
Set the current wheel position
as A point
Set the current wheel position
as B point
clearClear AB Points
handlePrioritize handle control
externalPrioritize external control
Disable handle wheel (control
off
wheel on the stabilizer)
Control the wheel in reverse direction
verticalJoystick in vertical direction
horizontal Joystick in horizontal direction
2
"1" AB point settings are only available when connecting to ZHIYUN Servo
Follow Focus correctly.
"2" External control refers to remote control via Bluetooth or cable
controls other than local controls via the stabilizer. (Remote Control needs
to be purchased separately).
13
How to Use
Motor Torque Adjustment
The motor torque of the stabilizer shall be adjusted by 3 levels to adapt to the
specific camera and lens applied for ideal performance.
How to adjust :
1. Single press Menu and rotate the dial to "motor", then
press right to enter motor torque setting.
2. Rotate the dial to choose the appropriate motor force and
press right to confirm the option.
Motor Force
lowLowSony rx 100 series or pocket camera
medium
(default)
highHighSony A7R3+FE24-70 f4
Either the motor force is set too high or too low (unmatched with weight
capacity) can lead to camera shake and affect normal use of the stabilizer.
Weight
Capacity
Medium Sony A6500+FE35 f2.8
Examples of Compatible Camera & Lens
14
How to Use
Control Mode Description
Motors circled in red will auto move with the stabilizer, while motors
circled in grey are locked instead of moving with the stabilizer.
Tilt AxisTilt Axis
Roll AxisRoll Axis
Pan AxisPan Axis
Pan Following Mode (PF): Push
up the PF/L mode switch
The camera pans left/right following
the movement of the stabilizer while
the tilt and roll axes are locked. Push
the joystick up/down allows manual
control of the tilt axis.
Tilt AxisTilt Axis
45° of the Roll AxisRoll Axis
Pan AxisPan Axis
Point of View Mode (POV): Single
press the POV mode button
This mode allows the camera to
roll left/right at a Max. angle of
45° and all the three motors with
unlimited 360° rotation following
the movement of the stabilizer.
Locking Mode (L): Push down the
PF/L mode switch
This mode locks the movement of
all three axes to keep the camera
fixed on a shooting direction. Push
the joystick up/down and left/right
allows manual control of the tilt axis
and pan axis.
Follow Mode (F): Press the Mode
button at the back
The camera pans and tilts following
the movement of the stabilizer. Push
the joystick left/right allows manual
control of the roll axis.
15
How to Use
Tilt Axis
Roll Axis
Pan AxisPan Axis
Tilt Axis
Roll Axis
PhoneGo Mode (GO): Press the
PhoneGo Mode button
The camera pans left/right and tilts
up/down following the movement
of the stabilizer in faster speed while
the roll axis is locked.
Sling Mode
Before using with Sling Mode, please be sure to put the tripod lock switch
to lock.
Vortex Mode (V): Double press
the POV mode button
The camera tilts with a 90° angle
following the movement of the
handle while the roll axis is locked.
Please use this mode in an underslung
gesture and push the joystick right/left
to rotate the pan axis.
Upright Mode
16
How to Use
Manual Angle Lock
Under pan following mode and locking mode, you can manually rotate the
camera to a certain angle, then loosen your grip and the camera position will
be fixed. Under pan following mode, you can manually adjust the angle of tilt
axis. Under locking mode, you can manually adjust the angle of pan axis and
tilt axis.
17
APP Operations
Image Transmission System and APP Operations
1. WEEBILL LAB image transmission system can only be applied in combination
with mobile APP "ZY Play".
2. Before using the image transmission system, please confirm that the camera
control cable is properly connected.
3. For Sony camera, please confirm the USB connection setting of the camera
is set as computer remote control mode, and the static image storage in
the computer remote control is set as computer + camera device. Set LUMIX
camera to PC (Tether) mode in USB mode.
4. With the TransMount Phone Holder with Crown Gear (needs to be
purchased separately), it is easier to mount the phone on the stabilizer and
adjust the viewing angle of the phone screen.
Download APP
Scan the left QR code (Android 5.0 and above, IOS 9.0
and above) or search "ZY Play" directly in the app
store to download "ZY Play".
1. Paired with the APP “ZY Play” designed for
WEEBILL LAB, it can provide you better use of
various functions.
2. The ZHIYUN APP is subject to regular update,
try out now to discover more functions.
18
APP Operations
How to Connect Stabilizer to Smartphone/Tablet
1. Power on the stabilizer and connect the stabilizer with the camera with the
corresponding camera control cable. Turn on Bluetooth and WIFI on the
mobile device.
2. Open "ZY Play" and select the product page corresponding to WEEBILL
LAB. Click "connect device", and select the stabilizer with the corresponding
Bluetooth name (the Bluetooth name WEEBILL LAB_XXXX can be viewed in
About).
3. After entering the APP's main interface, tap the WIFI icon [ ] and connect
to the stabilizer WIFI according to the prompts (Initial default password
12345678).
Overview of the Main Functions
Camera Parameters
Settings
Image Transmission
System
Focus/zoom Control
Stabilizer Parameters
Settings
Stabilizer Calibration
ZY Play
Video and Photo
Panorama
Firmware Upgrade
19
Calibration and Firmware Upgrade
When to Calibrate the Stabilizer
Please calibrate the stabilizer when necessary.
Syndromes that requires calibration
1. Slight deviation is found in the tilt angle of the camera in
level position after startup.
2. Slight deviation is found in the roll angle of the camera in
level position after startup.
3. Frequent small angle correction is found when the camera
is in level position while the stabilizer stays still.
1. Slight deviation is found in the level position after the
initialization of the stabilizer.
2. The stabilizer has not been used for a long time.
3. The stabilizer undergoes significant temperature difference
in operation environments.
Slight deviation is found in the tilt or roll angle of the camera
in level position after initialization and six-side calibration of
the stabilizer.
How to
calibrate
Initializing the
stabilizer
Six-side
calibration
Fine tune
motor force
Initialization Method
1. Correctly install the batteries.
2. Hold the camera mounting plate with one hand, long press the power
button to start up the stabilizer; long press the POV mode button to enter
standby mode while keeping hold of the camera mounting plate through
the whole process in case of start-up failure.
3. Put the stabilizer still on a table surface, and wait for about 30 sec, and the
stabilizer will automatically complete initialization.
20
Calibration and Firmware Upgrade
Six-side Calibration
Six-side calibration via OLED display guide
1. Power on the stabilizer and enter standby mode, then press menu and
rotate the dial to "calibration" option. Press right to confirm selection.
2. As seen below, conduct six-side calibration following the 6 steps shown in
the graphs, finish by pressing any button to exit the menu.
STEP 1STEP 2
STEP 3STEP 4
STEP 5STEP 6
Six-side calibration through APP
Connect the stabilizer to "ZY Play". Enter "Calibration" and finish six-side
calibration following the APP instruction.
Six-side calibration is simply to place six sides of the camera mounting
plate respectively and sequentially in vertical to a level surface.
21
Calibration and Firmware Upgrade
Motor Fine-tuning
Fine tune the motor through stabilizer:
1. Power on the stabilizer and enter standby mode, then rotate the dial and
press right to enter the "angle" option;
2. Adjust the value of the tilt and roll axis angle to your actual needs.
Fine tune the motor through APP
Connect the stabilizer to "ZY Play". Enter "Gimbal Settings", and adjust the
value of the tilt and roll axis angle to your actual needs.
Firmware Upgrade
"ZY Play" will automatically search for the latest firmware after the stabilizer
is connected. Tap to upgrade automatically.
Before firmware upgrade, please ensure that the power level of both
stabilizer and phone remain above 50%. Do not turn off the stabilizer
during upgrade.
22
Product Specifications
Product Model: CR104
Min.Standard Max.Remark
Charging Voltage6.4V-8.4V
Charging Current 250mA-3000mA
Output Voltage-5V-
Output Current
(Micro USB port)
Tilt Mechanical
Range
Roll Mechanical
Range
Pan Mechanical
Range
Operation
Temperature
Battery Capacity2600mAh
Battery Runtime6h12hLab Data 1
Charging Time2.5hLab Data 2
Valid Payload300g3000g
BluetoothBluetooth 5.0
WIFI
"Lab Data 1": The 12h runtime is concluded via a complete test session in
which the stabilizer is well balanced with SONY A7+10-18 F4 lens installed. The
ambient temperature is 25° and it is placed at rest throughout the test session.
"Lab Data 2" WEEBILL LAB automatically stops charging when the charging
temperature is not within the reference temperatures in order to protect
device and batteries. When the temperature is over 25°, please use 5V/2A
power adapter to proceed this test. The charging time varies according to
different environment and actual results may be different. When the charging
temperature is lower, charging current value is smaller so charging time is
extended. All data in this User Guide are generated in internal experiments
of ZHIYUN lab. Under different circumstances, data may vary to some extent.
Please refer to actual operation circumstances.
Note: The contents marked grey are for internal reference only. In different
objective circumstances, the data will have different degrees of deviation,
please take into consideration of actual operation circumstances while
referring to the data thus provided.
-500mA-
-360°-Unlimited Rot
-360°-Unlimited Rot
-360°-Unlimited Rot
-10°25°45°
Two 18650 Li-ion
Batteries
Maximum effective range of image transmission signal
in WIFI 2.4G: 50m (no occlusion, no interference)
23
Disclaimer and Warning
Thank you for purchasing ZHIYUN WEEBILL LAB. The information contains
herein affects your safety, legitimate rights and obligation. Please read this
instruction carefully to ensure proper configuration before use. Failure to read
and follow this instruction and warnings herein may result in serious injury
to you or bystanders, or damage to your device or property. Guilin Zhishen
Information Technology Co., Ltd. reserves all rights for final explanation on this
instruction and other documents related to WEEBILL LAB. The information is
subject to update without notice. Please visit www. Zhiyun-tech.com to obtain
the latest product information.
By using this product, you hereby signify that you have read this document
carefully and that you understand and agree to abide by the terms and
conditions herein. You agree that you are solely responsible for your own
conduct while using this product, and for any consequences thereof. You agree
to use this product only for purposes that are proper and in accordance with
all terms, precautions, practices, policies and guidelines ZHIYUN has made and
may make available.
ZHIYUN accepts no liability for damage, injury or any legal responsibility
incurred directly or indirectly from the use of this product. Users shall observe
safe and lawful practices including, but not limited to, those set forth herein.
ZHIYUN™ is the trademark of Guilin Zhishen Information Technology Co., Ltd.
(hereinafter referred to as “ZHIYUN” or “ZHIYUN TECH”) and its affiliates.
All product names or marks referred to herein are trademarks or registered
trademarks of their respective holders.
Reading Tips
Legends: Hints and Tips Important
Warnings
Read the ENTIRE User Guide to become familiar with the features of this
product before operating. Failure to operate the product correctly can result
in damage to the product or personal property and cause serious injury. This is
a sophisticated product. It must be operated with caution and common sense
and requires some basic mechanical ability. Failure to operate this product in a
safe and responsible manner could result in injury or damage to the product or
other property. This product is not intended for use by children without direct
adult supervision. DO NOT use with incompatible components or in any way
otherwise as mentioned or instructed in the product documents provided by
ZHIYUN. The safety guidelines herein contain instructions for safety, operation
and maintenance. It is essential to read and follow all of the instructions and
warnings in the User Guide, prior to assembly, setup or use, in order to operate
the product correctly and avoid damage or serious injury.
24
Disclaimer and Warning
Safe Operation Guidelines
CAUTION:
1. WEEBILL LAB is a high-precision control device. Damage may be caused
to WEEBILL LAB if it is dropped or subject to external force, and this
may result in malfunction.
2. Make sure the rotation of the gimbal axes is not blocked by external
force when WEEBILL LAB is turned on.
3. WEEBILL LAB is not waterproof. Prevent contacts of any kind of liquid
or cleaner with WEEBILL LAB. It is recommended to use dry cloth for
cleaning.
4. Protect WEEBILL LAB from dust and sand during use.
WARNING
To avoid fire, serious injury, and property damage, observe the following
safety guidelines when using, charging, or storing your batteries.
Battery Use
1. Prevent the batteries to come into contact with any kind of liquid. Do not
leave batteries out in the rain or near a source of moisture. Do not drop
the battery into water. If the inside of the battery comes into contact with
water, chemical decomposition may occur, potentially resulting in the
battery catching on fire, and may even lead to an explosion.
2. If the battery falls into water with the stabilizer during use, take it out
immediately and put it in a safe and open area. Maintain a safe distance
from the battery until it is completely dry. Never use the battery again, and
dispose of the battery properly as described in the Battery Disposal section
below.
3. If the battery catches fire, use water, water spray, sand, fire blanket, dry
powder, or carbon dioxide fire extinguisher immediately to put out the fire.
Battery-caused fire may lead to explosion. Please extinct the fire by applying
the methods recommended above according to the actual situation.
4. Never use non-ZHIYUN batteries. If replacement or backup is needed,
please purchase new batteries from ZHIYUN's official website or authorized
channels. ZHIYUN takes no responsibility for any damage caused by nonZHIYUN batteries.
5. Never use or charge swollen, leaky, or damaged batteries. Never use or
charge if the battery smells, or overheats (exceeding maximum temperature
of 160°F/71°C). If your batteries are abnormal, contact ZHIYUN or a ZHIYUN
authorized dealer for further assistance.
6. The battery should be used within the temperature range from -10°C to
45°C. Use of battery in environments above 45°C may lead to a fire or
explosion. Use of battery below -10°C may lead to serious battery damage.
7. Do not use the battery in strong electrostatic or electromagnetic
environments. Otherwise, the battery protection board may malfunction.
8. Do not disassemble or use any sharp object to puncture the battery in any
way. Otherwise, the battery may leak, catch fire or explode.
25
Disclaimer and Warning
9. Do not mechanically strike, crush, or throw the battery. Do not place heavy
objects on the battery or charger.
10. Electrolytes inside the battery are highly corrosive. In case of accidental
contact of any electrolytes with your skin or eyes, rinse immediately with
water for at least 15 minutes and seek medical advice as soon as possible.
11. Do not use the battery if it has been involved in a crash or heavy impact.
12. Do not heat the battery and never put the battery in a microwave oven or
in a pressurized container.
13. Do not place the battery on a conductive surface (such as a metal desk
surface, eye-glasses, watch, jewelry, etc.)
14. Prevent use of wires or other metal objects that could cause positive and
negative short-circuit to the battery.
15. If the battery terminal is dirty, wipe it with a clean, dry cloth. Otherwise
it will cause a bad battery connection, which may result in energy loss or
charging failure.
Battery Charging
1. The battery will automatically stop charging once it is full. Please disconnect
the battery and the charger when fully charged.
2. Do not attach the batteries to a wall outlet or car charger socket directly.
Always use a ZHIYUN approved adapter for charging. ZHIYUN takes no
responsibility if the battery is charged using a non-ZHIYUN charger.
3. Do not put the battery and charger near flammable materials or on
flammable surfaces (such as carpet or wood). Never leave the battery
unattended during charging to prevent any accident.
4. Do not charge the battery immediately after use, because the battery
temperature may be too high. Do not charge the battery until it cools down
to normal room temperature. Charging the battery with its temperature
over 45°C or lower than 0°C may lead to leakage, overheating, or damage.
5. Examine the charger before use, make sure there is no damage to the
enclosure, cord, plug, or other parts. Never use a damaged charger. Do not
clean the charger with any liquid containing alcohol or other flammable
solvents. Disconnect the charger when not in use."
Battery Storage
1. Keep batteries out of the reach of children and pets.
2. Do not leave the battery near heat sources such as a furnace or heater,
or inside of a vehicle on hot days. Never expose the battery in any
environment with temperature of over 60°C. The ideal storage temperature
is 22°C-28°C.
3. Store batteries in a dry environment.
4. Do not leave the battery unused for too long after it has been completely
discharged to prevent over-discharge of battery which may result in battery
damage and permanent failure.
26
Disclaimer and Warning
Battery Maintenance
1. Do not over-charge or over-discharge the battery, which will damage the
battery;
2. The battery performance will be affected for not being used for a long
time;
3. Never use the battery when the temperature is too high or too low;
4. Do not store the battery in any environment with a temperature of over
60°C.
Battery Disposal
1. Please fully discharge the battery before putting it in the designated
recycling bin. Batteries contain hazardous constituents and it is forbidden
to put the battery in general waste bin. For related details please abide by
the local laws and regulations on battery recycling and disposal.
2. If the battery cannot be fully discharged, never put it in battery recycling
bin. Please contact battery recycling companies for a proper solution.
Search and follow “Zhiyun Tech” on Facebook, Instagram, Twitter,
YouTube and Vimeo to connect with us.
Tel: +86 (0) 773-3561275
USA Hotline: +1 808-319-6137,9:00-18:00 GMT-7,Mon-Fri
Europe Hotline: 0031-297303057,10:00-17:00 GMT+1,Mon-Fri
Web: www.zhiyun-tech.com
E-mail: service@zhiyun-tech.com
Address: 6th floor Building No.13 Creative Industrial Park, GuiMo Road, Qixing
District, Guilin
27
Warranty Card
Warranty Period
1.
Customers are entitled to replacement or free repair service in case of quality
defect(s) found in the product within 15 days upon receipt of the product.
2.
Customers are entitled to free repair service from ZHIYUN for any product
proven defective in material or workmanship that results in product failure during
normal consumer usage and conditions within the valid warranty period, which
is 12 months counting from the date of selling.
3.
Some states or countries do not allow limitations on how long an implied
warranty lasts, so the above warranty term may not apply to you.
Exceptions
1.
Products subjected to unauthorized repair, misuse, collision, neglect,
mishandling, soaking, accident, and unauthorized alteration.
2.
Products subjected to improper use or whose labels or security tags have been
torn off or altered.
3.
Products whose warranty has expired.
4.
Products damaged due to force majeure, such as fire, flood, lightening, etc.
Warranty Claim Procedure
1.
If failure or any problem occurs to your product after purchase, please contact a
local agent for assistant, or you can always contact ZHIYUN’s customer service
through email at service@zhiyun-tech.com or website at www.zhiyun-tech.com.
2.
Your local agent or ZHIYUN’s customer service will guide you through the
whole service procedure regarding any product issue or problem you have
encountered. ZHIYUN reserves the right to reexamine damaged or returned
products.
28
Warranty Card
Customer information
Customer Name :Contact No :
Address :
Sales Information
Sales Date :Prod. Serial No :
Dealer :
Contact No :
#1 Maintenance Record
Service Date :Signature of Repairman :
Cause of
Problem :
Service Result :□Solved□Unsolved
□Refunded
(Replaced)
Certificate of Quality
This product is confirmed to meet quality standards and