ZHIXUAN ZXXS170-L02 Specification

PROPRIETARY NOTE

THIS SPECIFICATION IS THE PROPERTY OF BOE OT AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE OT AND MUST BE RETURNED TO BOE OT UPON ITS REQUEST

TITLE Z X X S170-L02

Product Specification

Rev. 0

BEIJING BOE OPTOELECTRONICS TECHNOLOGY

SPEC. NUMBER

S864-5002

B2006-5006-O(1/3)

PRODUCT GROUP

TFT-LCD

REV.

ISSUE DATE

2006.10.16.

PAGE

OF 27

A4(210 X 297)

PRODUCT GROUP

REV

ISSUE DATE

TFT- LCD PRODUCT

REVISION HISTORY

2006.10.16

PREPARED DATE DESCRIPTION OF CHANGES ECN NO.REV.

Dong Xue06.10.16Initial Release-O

SPEC. NUMBER

S864-5002

B2006-5006-O(2/3)

SPEC. TITLE

Z XXS170-L02 Product Specification

PAGE

OF 27

A4(210 X 297)

PRODUCT GROUP

REV

ISSUE DATE

No.

TFT- LCD PRODUCT

2006.10.16.

Contents

PageItem

General Description1.0

Absolute Maximum Ratings2.0

Electrical Specifications3.0

Optical Specifications4.0

Interface Connection5.0

Signal Timing Specifications6.0

Input Signals, Basic Display Colors & Gray Scale of Colors7.0

Power Sequence8.0

Mechanical Characteristics9.0

Reliability Test10.0

Handling & Cautions 11.0

Product Serial Number12.0

Packing13.0

Appendix14.0

SPEC. NUMBER

S864-5002

B2006-5006-O(3/3)

SPEC. TITLE

Z XXS170-L02 Product Specification

PAGE

OF 27

A4(210 X 297)

PRODUCT GROUP

REV

ISSUE DATE

TFT- LCD PRODUCT

1.0 GENERAL DESCRIPTION

1.1 Introduction

HT170E01-300 is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 17.0 inch diagonally measured active area with SXGA resolutions (1280 horizontal by 1024 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16,194,227 colors. The TFT-LCD panel used for this module is adapted for a low reflection and higher color type.

Connector (CN )

LVDS Input Signal

LVDS Rx

T/CON

mini-LVDS Tx

Gate Driver

Source Driver

TFT LCD Panel

2006.10.16.

CN21 CN22

1280 ×1024

VDD

1.2 Features

 LVDS Interface with 2 pixel / clock  High-speed response  Low power consumption  6-bit (FRC) color depth, display 16,194,227 colors  Incorporated edge type back-light (Four lamps)  High luminance and contrast ratio, low reflection and wide viewing angle  DE (Data Enable) & H-Sync & V-Sync mode  RoHS Compliant

DC/DC

Gamma

Vcom

CN23 CN24

SPEC. NUMBER

S864-5002

B2006-5006-O(3/3)

SPEC. TITLE

Z XXS170-L02 Product Specification

PAGE

OF 27

A4(210 X 297)

PRODUCT GROUP

REV

ISSUE DATE

TFT- LCD PRODUCT

1.3 Application

 Desktop Type of PC & Workstation Use  Slim-Size Display for Stand-alone Monitor  Display Terminals for Control System  Monitors for Process Controller

1.4 General Specification

The followings are general specifications at the model ZXXS170-L02.

2006.10.16.

UnitSpecificationParameter

Remarks

RGB Vertical stripePixel arrangement

Normally WhiteDisplay mode

Haze 25%, 3HSurface Treatment

Note : 1. LED(Light Emitting Diode)

mm337.92(H) * 270.336(V) Active area

pixels1280(H) ×1024(V)Number of pixels

mm0.264(H) ×0.264(V)Pixel pitch

colors16,194,227Display colors

mm358.5(H) × 296.5(V) × 17.0(D) typ.Dimensional outline

gram2200 (max.)Weight

Note 1Top/Bottom edge side, >1-LEDtypeBack-light

SPEC. NUMBER

S864-5002

B2006-5006-O(3/3)

SPEC. TITLE

Z XXS170-L02 Product Specification

PAGE

OF 27

A4(210 X 297)

PRODUCT GROUP

REV

ISSUE DATE

TFT- LCD PRODUCT

2.0 ABSOLUTE MAXIMUM RATINGS

The followings are maximum values which, if exceed, may cause faulty operation or

damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2.

Power Supply Voltage Logic Supply Voltage Back-light Lamp Current Back-light Lamp Frequency Operating Temperature Storage Temperature

< Table 2. Absolute Maximum Ratings>

+500T +60-20T

[VSS=GND=0V]

V12 VVDD+0.3VSS-0.3V

A2.08-I

KHz(80)30F

℃

RemarksUnitMax.Min.SymbolParameter

Ta = 25 ℃

2006.10.16.

Note : 1) Temperature and relative humidity range are shown in the figure below.

Wet bulb temperature should be 50OC max. and no condensation of water.

100

O perating R ange

Relative Humidity (%RH)

Storage Range

20 40 60 80-20

Tem perature (˚C)

SPEC. NUMBER

S864-5002

B2006-5006-O(3/3)

SPEC. TITLE

Z XXS170-L02 Product Specification

PAGE

OF 27

A4(210 X 297)

PRODUCT GROUP

REV

ISSUE DATE

TFT- LCD PRODUCT

3.0 ELECTRICAL SPECIFICATIONS

< Table 3. Electrical specifications >

Power Supply Voltage Power Supply Current

In Rush Current I Permissible Input Ripple Voltage High Level Differential Input

Threshold Voltage Low Level Differential Input

Threshold Voltage Back-light Lamp Voltage Back-light Lamp Current Back-light Lamp operating Frequency

Lamp Start Voltage

rush

V12--V

Note 1

mA12001000-I

- 3.0 A Note 2 VDD= 5.0VmV100V

mV+100-V

Vcm = 1.2V typ.

mV--100V

V12--V

A2.08--I

Note 3KHz70-30F 1400 1700

rms

25 ℃ Note 4

0 ℃ Note 5V

2006.10.16.

[Ta =25±2 ℃]

RemarksUnitMax.Typ.Min.Parameter

W6.05.0-P

IBL=6.5mA, Note 6W

W25-P

Power Consumption

total

18.33P

←

Notes : 1. The supply voltage is measured and specified at the interface connector of LCM.

The current draw and power consumption specified is for VDD=5.0V, Frame rate=75Hz and Clock frequency = 67.5MHz. Test Pattern of power supply current

a) Typ : Black Pattern b) Max : Dot Pattern

2. Duration of rush current is about 2 ms and rising time of VDD is 520 μs ± 20 %

3. The lamp frequency should be selected as different as possible from the horizontal synchronous frequency and its harmonics to avoid interference, which may cause line flow on the display

4. The voltage above this value should be applied to the lamps for more than 1 second to start-up.

Otherwise the lamps may not be turned on.

5. Calculated value for reference (VBL× IBL) ×4 excluding inverter loss.

SPEC. NUMBER

S864-5002

SPEC. TITLE

Z XXS170-L02 Product Specification

= 6.5mAHrs50000Lamp Life

PAGE

OF 27

B2006-5006-O(3/3)

A4(210 X 297)

PRODUCT GROUP

REV

ISSUE DATE

TFT- LCD PRODUCT

2006.10.16.

4.0 OPTICAL SPECIFICATION

4.1 Overview

The test of Optical specifications shall be measured in a dark room (ambient luminance ≤ 1 lux and temperature = 25±2℃) with the equipment of Luminance meter system (Goniometer system and TOPCON BM-5) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0°. We refer to θ the 12 o’clock direction (“upward”), θ

Ø=180

(=θ3) as the 3 o’clock direction (the “right”), θ

Ø=0

(= θ9) as the 9 o’clock direction (“left”) and θ

Ø=270

o’clock direction (“bottom”). While scanning θ and/or Ø, the center of the measuring spot on the Display surface shall stay fixed. The measurement shall be executed after 30 minutes warm-up period. VDD shall be

5.0V +/-10% at 25°C. Optimum viewing angle direction is 6 ’clock.

4.2 Optical Specifications

[VDD = 5.0V, Frame rate = 60Hz, Clock = 54MHz, IBL= 6.5mA, Ta =25±2 ℃]

Horizontal

Viewing Angle

Vertical

Horizontal

Viewing Angle

Vertical

Luminance of White

White luminance uniformity Note 4%ΔY

White

Red

Reproduction

of color

Green

Blue

Rising

Response Time

Falling

CR > 10

CR > 5

Θ = 0°

(Center)

Normal

Viewing

Angle

1.5

3.5

1000

--75

0.3430.3130.283W

0.3590.3290.299W

0.6750.6450.615

0.3640.3340.304R

0.3220.2920.262G

0.6310.6010.571G

0.1730.1430.113B

0.1170.0870.057B 3

Deg.-8070

Deg.-8070 Deg.-8070

Deg.--80

Deg.--80 Deg.--80

(= θ12) as

Ø=90

(= θ6 ) as the 6

RemarkUnitMax.Typ.Min.ConditionSymbolParameter

Note 1Deg.-8070

Note 1Deg.--80

Note 2800550CRContrast ratio Note 3nit--Y

Note 5

Note 6

Note 7%2.0--CTCross Talk

SPEC. NUMBER

S864-5002

B2006-5006-O(3/3)

SPEC. TITLE

Z XXS170-L02 Product Specification

PAGE

OF 27

A4(210 X 297)

PRODUCT GROUP

REV

ISSUE DATE

TFT- LCD PRODUCT

2006.10.16.

Note :

1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface.

2. Contrast measurements shall be made at viewing angle of θ= 0° and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See FIGURE 1 shown in Appendix) Luminance Contrast Ratio (CR) is defined mathematically.

CR =

3. Center Luminance of white is defined as the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations

Luminance when displaying a white raster Luminance when displaying a black raster

shown in FIGURE 2 for a total of the measurements per display.

4. The White luminance uniformity on LCD surface is then expressed as : ΔY = ( Minimum Luminance of 9points / Maximum Luminance of 9points ) * 100 (See FIGURE 2 shown in Appendix).

5. The color chromaticity coordinates specified in Table 4. shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel.

6. The electro-optical response time measurements shall be made as FIGURE 3 shown in Appendix by switching the “data” input signal ON and OFF. The times needed for the luminance to change from 10% to 90% is Td, and 90% to 10% is Tr.

7. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance (Y luminance (YB) of that same area when any adjacent area is driven dark. (See FIGURE 4 shown in Appendix).

) of a 25mm diameter area, with all display pixels set to a gray level, to the

SPEC. NUMBER

S864-5002

B2006-5006-O(3/3)

SPEC. TITLE

Z XXS170-L02 Product Specification

PAGE

OF 27

A4(210 X 297)

+ 18 hidden pages

ZHIXUAN ZXXS170-L02 Specification

Specifications and Main Features

Frequently Asked Questions

User Manual