WINDOW CLEANING ROBOT
CONTENTS
1.Safety Criteria
1. Safety Criteria
2. Product Composition
2.1 Package contents
2.2 Technical parameters
3. Product Manual
3.1 Precautions before use
3.2 Install the cleaning clo th
3.3 Connect the adapter
3.4 Assemble the safety rope assembly
3.5 Product work
3.6 Product pause
3.7 End the work
4. Maintenance
4.1 Cleaning cloth
4.2 Bottom components
5. Status Indicator
6. Fault Description
7.FCC- Mobile Device
8. Warranty Card
2
5
5
5
6
7
7
8
9
9
10
11
11
13
13
13
15
16
18
19
Please read this manual carefully before using the product.
Save the manual.
When using the product, plea se maintain consistent vigilance and keep
the following precaution s:
1.This product is strictly forbidden to use under the
following conditions:
1.1 Products can not be used by ch ildren under 12 y ears old and the
person physically or menta lly impaired. Please do not allow children
close to the working robot or as r obot be a toy to play.
1.2 Do not use this product on gla ss that has broke n marks, ad paper, or
bumps to avoid the risk of broke n glass, droppe d product, and so on.
1.3 Do not use this product on non-planar glass s uch as curved surface
and beveled surfaces.
1.4 Do not use this product on framed glass with a glass frame thickness
of less than 5 mm.
1.5 Prohibit the use of large areas of wet or o ily glass to avoi d slipping
products caused by the risk of f alling.
1.6 After cleaning, you can use detergent to clean the cleaning cloth.
After cleaning, please dry i t in time.
1.7 Do not place this product in w ater or other liquids to reduce the risk
of electrical shock. Do not st ore this product where it may fall or be
pulled into the tub or sink.
1.8 Do not use the product in a situ ation where the product is not
completely adsorbed or has b een significantly damaged.
1.9 Do not touch the plug or the pro duct with wet hands.
1.10 Do not place the machine on h ousehold appliances, damp or have a
fire source to charge, so as to avoid unnec essary losses .
1.11 Even if the product has been seriously damage d, the products can be
banned.
1.12 Strictly prohibit the u se of this product without fixing safety rope
assemblies.
1.13 Do not use the product with a d amaged power cord or an electrical
1.Safety Criteria
1.Safety Criteria
outlet. Do not use the product w hen it is not working properly due to
dropping, damaging or wate r ingress. To avoid inj ury, the product should be repaired by the manufac turer or its after-sales service department.
1.14 The cleaning cloth can be applied to t he wet glass surface, Nonreflux of water droplets on gl ass. When the flow of water on t he glass is
left, it is strictly prohibi ted to use this product.
2.The following conditions should be noted when
using this product:
2.1 Products just can use for outside when the temperature at 0-40
degrees, no heavy wind, no rai n and dry air. When using the product
through the safety rope and sa fety buckle must be properly connected.
2.2 Always keep the product powered on while the product is in
operation.
2.3 Use only in a domestic envir onment. Do not use in commercial or
industrial areas.
2.4 Please use the product as in dicated in the instructions, use only the
accessories recommende d or sold by the manufacturer; use only the
original adapter made by the m anufacturer, and
ensure that the voltage of the p ower supply is in line with the voltage
marked on the adapter.
2.5 Please use the power line ca refully to avoid the damage. It is
forbidden to use the power lin e to drag, pull the product or use the power
line as a handle; it is forbidde n to close the glass window with the power
line or put the goods on the power l ine in the process of use, and the
power line should be far away fr om the heat source.
2.6 If the soft wires of the power c ord are damaged, they must be
replaced by the manufactur er, h is or her maintenance department or
similar professionals in o rder to avoid danger.
2.7 The plug must be unplugged from the soc ket before maintaining or
cleaning the product, but no t from the socket by pulling the power cord.
Please use the product in accordance with the
instructions of this manual. The company is not
responsible for any loss or injury caused by
improper use.
2. Product Composition
2. Product Composition
2.1 Package Contents
Host
Safety Rope
Components
Adapter Component
Clean Cloth
2.2 Technical Parameters
Instruction
Manual
2.3 Part name
Host
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1. Pause /St art button
2. Handle
3. Power swi tch
4. Status in dicator
5. Battery i ndicator
6. Power jac k
7. Air outlet
8. Guide whe el
9. Floatin g wiping chassi s
10. An ti- drop senso r
11. Driv e wheel
12. Suctio n sensor
13. Ai r inl et
14. Cleani ng cloth paste ar ea 1
15. Cleani ng cloth paste ar ea 2
Operating Voltage (V)
Rated input voltage (V)
Adapter Type: WT-2403750
Input: AC110-24 0V 50/60Hz
Rated power (W)
Output: DC24V 3.75A
3. Product Manual
3.1 Precautions before use
It is strictly forbidden to us e
this product on framed glass
with a thickness of the border
(height difference from the
glass surface to the bezel) of
less than 5 mm.
Use this product in a framed
or frameless ratio of ≥
60 * 60 cm
3. Product Manual
When the product is working on a horizontal glass surfac e, the
remote control should be use d to control the operation of the product.
If you use this product on windo ws that are not com pletely vertical,
the product may not function p roperly. Make sure that you a re in the
side care area and, if necessa ry, assist the product.
This product can not be used
in the inverted case.
3.2 Install the cleaning cloth
If there is too much dust on
the surface of the glass, wipe
out a clean area of product
size before using the produc t
for product adsorption.
Place two small cloth evenly o n
the left and right sides of the
machine.
Place the square cloth evenl y on
the middle of the machine.
Before use, spray a small amou nt of water on the cleaning cloth and
place it on the surface of the gla ss.Do not pour water on the glass
surface or on the product.
3. Product Manual
20 cm
Glass
Rail
3. Product Manual
3.3 Connect the adapter
Disassemble the power line e nd
of the product and the power
line of the adapter, connect both
ends of the extension line to th e
power line end of the product' s
power supply line and the
adapter power line, and tigh ten
up the power line at the end of
the power supply line and the
adapter.
3.4 Assemble the safety rope assembly
When using this product to wip e the glass, use a safety rope assembly
to secure the product and impr ove the safety of the product.
3.5 Product work
1.
1 Connect the power supply
and make sure fasten the
safety rope
Do not disconnect the power
supply while the product is
running. Otherwise, the
product will fall risk.
2 Turn the power switch on
When turn on, do not let the
hair or other small objects
near the fan, so as not to
affect product clogging the
fan running.
A. Safety Rope B. Sucker
Note: Sucker direction for us e
1. The suction cup is pressed to the top of the
glass when the suction handl e is separated.
2. Handle closure.
3. Pull the handle to confirm th e solid
adsorption.
3 Secure placement
Make sure the product is in the
normal operating state, pl ace it
on the glass surface, make sur e
the product is completely
adsorbed on the glass, then
release the handle.
If there is an immovable
obstacle (such as a guard rail ,
furniture, etc.) in front of t he
window, th en the window and
obstacle spacing greater t han
15cm can use this product.
3. Product Manual
3. Product Manual
4 Start working
:Press the button on the host ,
can start the automatic mode .
3.6 Product pause
In the process of working, by host
to pause, need to restore work ,
again press ,machine is
shipped accordingto the or iginal
route.
2 Power off
Press will turn off.
3 Disconnect power
Remove the safety clip and
disconnect the power suppl y.
3.7 End the work
End glass cleaning, the prod uct will return to the start position, the beep
sounds.
1 Remove the product
Grip the product handle, press
about 5 seconds, the fan stops
working, then remove the hos t
from window. Use a dry cloth to
gently wipe off the mark on the
glass.
4. Maintenance
4 Clean Walking Belt
When cleaning the cloth and bottom componen ts, unplug the
power and turn off the host.
4.1 Cleaning cloth
4. Maintenance
Walking belt : Clean with a dry
cloth so as not to damage the
product suction.
Remove the cleaning cloth,
soak in water at 20 ℃ for 2
minutes, then with a soft
brush clean .
Do not rub or wring dry,
dry naturally before use.
4.2 Bottom components
Fan: Clean with a dry cloth so
as not to damage the product
suction.
Fall prevention sensor:
Clean with a dry cloth to mainta in
its sensitivity.
5. Status Indicator
1. The indicator lights of the current
running status of the machin e are
yellow-green two-color l ight, blue
light and red light.
Yellow: Charging
Green: Charging completed
Blue: The machine is normal
Red: Machine abnormality
Troubleshooting Solution:
Number
1 Machine Slips
2
3
Appearance
Green or yellow
light is not on
Green light is on, but
the battery indicator
is not full
6. Fault Description
Solution
Clean cloth too wet or spray more water on
the glass. Replace other non-wet wipes or
spray the glass on the water to dry it.
Please contact the dealer or after-sales
service center.
Lithium battery normal loss, is a normal
phenomenon.
2. The indicator of the current power
of the machine (blue).
1 light is on : The battery electricity
is less than or equal to 25%
2 lights is on: The battery electricity
is less than or equal to 50%
3 lights is on: The battery electricity
is less than or equal to 75%
4 lights is on:The battery ele ctricity
is less than or equal to 100%
The red light is off
4
after about 5 seconds
Part of the glass area
5
6
leaked
Machine walking is
not straight / jitter
The window cleaner
can't walk in the middle
7
of the glass, but the
wheel can rotate
After the adapter is
powered on, the boot
8
does not start and the
fan does not work
Insufficient air pressure, please check if
the cleaning cloth is installed in place.
1. Check whether the four-corner borderless
detection sensor rebounds well. If there is
foreign matter, please take out the foreign
object.
2. Please check if the belt is dirty or slippery.
If yes, please clean the belt with a wet cloth.
Recalibrate the machine.
Remove the machine and clean the belt
dust with a damp cloth to increase the
friction with the glass surface.
Charge the internal lithium battery of the
machine to the power supply, it can be fully
charged in 3 hours, and the lithium battery
has a long-term loss of power and there is a
risk of damage.
6. Fault Description
7. FCC- Mobile Device
Product calibration:
The product has been calibra ted at the factory, and the use r does not need
to calibrate it under normal u se. If you have a serious bump and do not use
it for a long time, you may need to ca librate it yourself.The calibration
steps are as follows:
1. After the product is connected to the power supply, turn on the power
switch (or not open), and the ch arging in dicator lights up;
2. The hand-held machine is attached to t he surface of the window glass
to keep the machine head up;
3. long press the N button, the ma chine emits di di sound;
4. Keep the machine head verti cal to the left, short press the Z button, the
machine will make di di sound, a nd the calibration is completed.
FCC Caution:
This device complies with pa rt 15 of the FCC Rules. Operation is subject
to the following two conditi ons: (1) Th is device may not cause harmful
interference, and (2) this d evice must accept any interference received,
including interference t hat may cause undesired operation.
Any Changes or modificatio ns not expressl y approved by the party
responsible for complian ce could void the user's authority to operate
the equipment.
Note: This equipment has been tested an d found to comply with the
limits for a Class B digital dev ice, pursuant to part 15 of the FCC Rules.
These limits are designed to p rovide reasonable protection against
harmful interference in a re sidential installation. This equipment
generates uses and can radia te radio frequency energy and,if not
installed and used in accord ance with the instructions, may cause
harmful interference to ra dio communications. However, there is no
guarantee that interfere nce will not occur in a particular installati on. If
this equipment does cause ha rmful interference to
radio or television recept ion, which can be determined by turning the
equipment off and on, the user is encoura ged to try to correct the
interference by one or more of t he following measures:
-Reorient or relocate the re ceiving antenna.
-Increase the separation b etween the equipment and receiver.
-Connect the equipment int o an outlet on a circuit different from that to
which the receiver is connec ted.
-Consult the dealer or an expe rienced radio/TV technician for help.
*RF warning for Mobile devic e:
This equipment complies wi th FCC radiation exposure limits set forth
for an uncontrolled enviro nment. Th is equipment should be installed
and operated with minimum di stance 20cm between the radiator & your
body.
8. Warranty Card
Warranty Card
Dear client!
Thanks for using product. In o rder to off er perfect after sale service, our
service team would like to giv e you promise for standard service hereby.
Please keep well your valid do cument of purchasing as an evidence to get
our after sale service.
Product Quality Assurance Description:
1. Warranty time: start from pur chasing date, 12 months for main body.
2. Warranty service not includ e following situation: ①Inst ruction
Manual ②damage caused by accident or wrong op eration ③repair by
yourself without our permi ssion ④Exceed the warranty per iod
3. After warranty time, please consult our after sale service center about
repair cost.
Purchasing date
Purchasing way
19
WARRANTY CARD
Year Month Date
Order No.
Loading...