Network Bullet Cameras
Quick Guide
V1.01
BOM:3101C0QU
1
Safety and Compliance Information
Installation and removal of the unit and its accessories must be carried
out by qualified personnel. You must read all of the Safety Instructions
supplied with your equipment before installation and operation.
Installation
⚫ This device is a class A product and may cause radio interference.
Take measures if necessary.
⚫ Make sure the camera operates in an environment where the
temperature and humidity meet requirements. Keep the camera
from excessive pressure, vibration, moisture, dust, and intensive
electromagnetic radiation.
⚫ Use a power adapter or a PoE device that meets requirements.
Otherwise, the device may be damaged.
⚫ Make sure the length of the power cable between the power
adapter and the camera is not too long, otherwise the voltage of
the camera is lowered, causing the camera to work abnormally. If it
is required to lengthen the power cable, lengthen the cable
between the power adapter and the mains.
⚫ Do not hold the tail cable by hand for weight bearing. Otherwise,
the cable connector of the camera could be loosened.
⚫ When connecting to an external interface, use an existing
connection terminal, and ensure that the cable terminal (latch or
clamp) is in good condition and properly fastened. Ensure that the
cable is not tense during mounting, with a proper margin reserved
to avoid poor port contact or loosening caused by shock or shake.
⚫ The connectors of the tail cable must not be exposed. The bar cavity,
waterproof box, corrugated pipe and PVC pipe must be fully sealed
to protect the connectors from water. The waterproof components
for the RJ45 plug must be used properly to protect the network
cable from water.
⚫ During the process of transportation, special attention is required
for the protection of the transparent dome cover to prevent friction,
2
scratch and contamination, etc. In order to keep the cover clean, do
not remove the protective film on the cover during mounting. After
mounting is finished, remove the film before the device is powered
on.
⚫ Contact professionals for maintenance information. Do not attempt
to dismantle the device by yourself. We shall not assume any
responsibility for problems caused by unauthorized repair or
maintenance.
Maintenance
⚫ Caution: There will be risk of explosion if battery is replaced by an
incorrect type. Dispose of used batteries according to the
instructions.
⚫ If there is dust on the front glass surface, remove the dust gently
using an oil-free brush or a rubber dust blowing ball.
⚫ If there is grease or a dust stain on the front glass surface, clean the
glass surface gently from the center outward using anti-static gloves
or an oil-free cloth. If the grease or the stain still cannot be removed,
use anti-static gloves or an oil-free cloth dipped with detergent and
clean the glass surface gently until it is removed.
⚫ Do not use organic solvents, such as benzene or ethanol when
cleaning the transparent dome cover.
⚫ Never look at the transmit laser while the power is
on. Never look directly at the fiber ports and the
fiber cable ends when they are powered on.
⚫ Use of controls or adjustments to the performance
or procedures other than those specified herein
may result in hazardous laser emissions.
3
Regulatory Compliance
FCC statements
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and
receiver.
—Connect the equipment into an outlet on a circuit different
4
from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for
help.
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should
be installed and operated with a minimum distance of 20cm
between the radiator and any part of your body.
LVD/EMC/RE Directive
This product complies with the European Low Voltage
Directive 2014/35/EU and EMC Directive 2014/30/EU
and 2014/53/EU.
WEEE Directive–2012/19/EU
The product this manual refers to is covered by the Waste
Electrical & Electronic Equipment (WEEE) Directive and
must be disposed of in a responsible manner.
Battery Directive-2013/56/EC
Battery in the product complies with the European
Battery Directive 2013/56/EC.For proper
recycling,return the battery to your supplier or to
a designated collection point.
5
Default IP, Username and Password
⚫ Default IP address: 192.168.1.13
⚫ Default username: admin
⚫ Default password: 123456
The default password is used for your first login. To
ensure account security, please change the password
after your first login. You are recommended to set a
strong password (no less than eight characters).
Packing List
Contact your local dealer if the package is damaged or
incomplete. The attachments may vary with models, please see
the actual model for details.
Item
Quantity
Camera
1
User document
1
Accessory pack
1
6
Appearance
Dimensions
90.10mm
162.45mm162.45mm
39.00mm
62.67mm
39.00mm
39.00mm
62.42mm
8.90mm
31.00mm
7
Cable Connection
⚫ For specifications, see the latest product
datasheets.
⚫ Press and hold the RESET button for at least 15
seconds to restore factory default settings. Perform
this operation within 10 minutes after the device is
powered on or the reset will fail otherwise.
Mount Your Camera
(Optional) Insert the Micro SD Card
For cameras that support Micro SD, you need to insert the
Micro SD card after opening the bottom cover of camera. Do
not hot plug the Micro SD card after it is inserted. Otherwise
the camera or the SD card might be damaged.
IP Network
Network
interface
Power
interface
8
For recommended SD card specifications, contact your dealer.
1. Loosen the cross-
recessed screws to
open the bottom cover.
2. Insert the Micro SD
card.
Wall Mount
You can adopt wall mount or ceiling mount and purchase
hardware accessories by yourself. The following part takes wall
mount as an example. Ceiling mount is similar to wall mount
and therefore is omitted here.
1. Locate the positions of
the holes.
2. Drill holes on the wall.
Micro SD slot
9
3. Mount the plastic rivets
of self-tapping screws.
4. Screw the locknut to
loosen the universal
joint before attaching
your camera to the wall.
5. Mount your camera onto
the wall and connect all
cables.
6. Rotate the antenna to
the antenna interface
according to clockwise
direction.
Paste installation positioning
stickers on the wall and align
the cross center to the hole in
the wall.
Lead the cables across the hole
on the wall.
1
2
Use a Ø6-6.5mm drill bit.
Drill 30 mm-depth guide
holes according to the
positions marked by stickers.
1
2
Knock the plastic rivets
into the guide holes and
ensure that they are
tightened up.
Locknut
10
7. Adjust the monitoring
direction.
8. Power on your camera
and adjust images.
The preceding installation process is for concealed
installation, during which holes are punched on the
wall and cables are penetrated into the wall. If open
Lead tapping screws through
the guide holes in the base
and fix them on the wall by
using a screwdriver.
Reset
Antenna InterfaceAntenna Interface
Antenna
Adjust the opening of the
universal joints as required.
Rotate the spherical hinge of
the camera to get the desired
monitoring direction.
Tighten the locknut.
1
2
3
1
2
3
11
installation is adopted, cables are not penetrated into
the wall but threaded out from the outlet on one side
of the base.
Access Your Camera
Before you begin, check that:
⚫ Your camera is operating properly and connected to the
network.
⚫ The PC you are using is installed with Internet Explorer
7.0 or later.
Follow these steps to access your camera through the Web:
Open your browser, input the IP address of your camera in
the address bar and then press Enter to open the login page.
Enter the username and password and then click Login.
⚫ Install the ActiveX at your first login. When the
installation of the ActiveX is completed, open your
IE to log in.
⚫ For your first login with Windows 7, if the system
does not prompt you to install ActiveX, follow these
steps to turn off UAC: click the Start button, and
then click Control Panel. In the search box, type
uac, and then click Change User Account Control
Settings. Move the slider to the Never Notify
position, and then click OK. After UAC is turned off,
log in again.
12
⚫ If the installation failed, open Internet Option in IE
before login. Click the Security tab, click Trusted
sites, and then click Sites to add the website. If you
use Windows 7, you need to save the setup.exe to
your PC first, and then right-click the file, select Run
as administrator, and then install it according to
instructions.
Loading...