ZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY JCHR35H3 User Manual

JCHR35H3 Remote control User manual

一、

Remote control Effect Picture

JCHR35H3-1 JCHR35H3-2

二、 Remote control function description

2.1、 Pairing:

Remote control pair code:

1) put the battery into the remote control.

2) power the control box (supporting our control box).

3) hold down and hold the code control button on the control box to guide
the code indicator light to go out and release it. At this time, the code on the
control box indicates LED flashing, and the control box is in the state of pending
pairing.

4) at the same time, hold down the back up button on the remote control
and the leg up button. When the LED on the control box to be matched stops

flashing and the buzzer makes a sound, the pairing operation is completed.To
test whether or not the pairing is successful, back up/down, legs up and down
keys, buttons and so on related to drive, if you can hear the "tick" sound emitted
by the relay, specification matching success.Otherwise, repeat all the above
steps.

Note: after successful code alignment, operate any two buttons at the same time during
use, and the remote control will not send signals.

三三三三、、、、 Function description

1. Operate the flashlight button, and the flashlight lamp will be lit. If you no longer operate

the button after releasing the button 5S, the flashlight will be automatically extinguished.

2. The operation time of the flashlight button is greater than or equal to 5S, when the blue

backlight of the remote control flashes. At this time, operate any key in the ZG/ anti-snore

/TV/MEMORY A/MEMORY B button, and the blue backlight lamp stops flashing.If the

operation of the other buttons does not work, and the blue backlight lamp has been

flashing, the flashing time is 10S.

3. Operate any button, and the blue backlight lamp on the remote control button will be lit.

Release the button 5S and it will go out automatically.

4. Operate any two buttons at the same time, and the remote control will not send signals.

5. When the button loosens, the button value 0x00 shall be sent to indicate the release of

the button.

6. When the button is not released, the button value (100ms interval) shall be sent

continuously.

7. In addition to the anti-code key, when one key is pressed and any other key is pressed,

the sending button value is 0x00, which is equivalent to the release of the button.

四四四四、、、、 Key value to code table

Remote control
pictures

Button icon

key definitions

M1

M1

M2

M2

push rod up

push rod down

push rod up

push rod down

0X01

0X02

key value

0X04

0X05

Remarks

Remote control
pictures

Button icon

Memory location A

Memory location

ZG location

FLATlocation

Flashlight

key definitions

M1

push rod up

M1

push rod down

M2

push rod up

0X0a

B

0X0c

0X07

0X08

0X0b

key value

0X01

0X04

0X02

Remarks

M2

push rod down

M3

push rod up

M3

push rod down

ZG location

FLATlocation

Flashlight

0X05

0X14

0X15

0X07

0X08

0X0b

五五五五、、、、 Others

5.1. The operating frequency range：：：： 2.4GHZ~2.483GHZ;

5.2. Maximum RF output power of the product:

The overall power of the remote control is 0.38w, and the RF power is 1dBm ±

-1dbm

六六六六、、、、Remark

A、FCC 15.21 Information to user

Please note that changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

B、FCC 15.105 Information to the user (Class B)

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

—Consult the dealer or an experienced radio/TV technician for help.