Zhejiang Dahua Vision Technology HDBWABCDE WXY User Manual

Dahua HD IR Vandal Proof Network Dome Camera

User’s Manual

Version 1.2.1

Zhejiang Dahua Technology CO., LTD.

Welcome

Thank you for purchasing our Network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!

Please keep this user’s manual well for future reference!

i

Important Safeguards and Warnings

1

．．．．

Electrical safety

All installation and operation here should conform to your local electrical safety codes.

The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction)

Please note: Do not connect two power supplying sources to the device at the same time; it may
result in device damage! The product must be grounded to reduce the risk of electronic shock.

We assume no liability or responsibility for all the fires or electrical shock caused by improper handling

or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.

2

．．．．

Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.

3

．．．．

Installation

Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.

4

．．．．

Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.

5

．．．．

Environment

This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.

Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability

of the camera.

6. Daily Maintenance

Please shut down the device and then unplug the power cable before you begin daily maintenance
work.

ii

Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.

Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
Dome enclosure is the optical component, do not touch the enclosure when you are installing the
device or clean the enclosure when you are doing maintenance work. Please use professional optical
clean method to clean the enclosure. Improper enclosure clean method (such as use cloth) may result
in poor IR effect of camera with IR function.

7. Accessories

Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.

Accessory Name Amount

Network Camera Unit 1

Quick Start Guide 1

Installation Accessories Bag 1

CD 1

iii

Table of Contents

1 General Introduction

1.1

Overview

1.2

Features

1.3

Specifications

2 Structure

2.1

2.2

................................................................................................................................. 4

Components

Framework and Dimension

3 Device Installation

3.1

Installation Steps

.............................................................................................................. 1

................................................................................................................... 1

.................................................................................................................... 1

........................................................................................................... 2

............................................................................................................. 4

..................................................................................... 4

................................................................................................................. 7

...................................................................................................... 7

4 Quick Configuration Tool .................................................................................................... 10

4.1

Overview ................................................................................................................. 10

4.2

Operation ................................................................................................................ 10

5 Web Operation..................................................................................................................... 12

5.1

Network Connection............................................................................................... 12

5.2

Login and Main Interface....................................................................................... 12

6 FAQ

Appendix Toxic or Hazardous Materials or Elements

....................................................................................................................................... 14

............................................................. 15

iv

1111 General Introduction

General Introduction

General Introduction General Introduction

1.1

1.1 Overview

Overview

1.11.1

Overview Overview

This series network camera integrates the traditional camera and network video technology. It adopts
video data collection, transmission together. It can connect to the network directly without any auxiliary

device.

This series network camera uses standard H.264 video compression technology, which maximally
guarantees the video quality.

It supports the IR night vision function. In the night environments, the device can use the IR light to
highlight the object which is suitable for the surveillance function in the low illumination environments.
The waterproof design conforms to the IP 66 level. It has the sound waterproof function suitable for
use in the outdoor environments.

It can be used alone or used in a network area. When it is used lonely, you can connect it to the
network and then use a network client-end. Due to its multiple functions and various uses, this series
network camera is widely used in many environments such office, bank, road monitor and etc.

1.2

1.2 Feature

Featuressss

1.21.2

FeatureFeature

User

Management

Storage

Function

Alarm

Function

Network

Monitor

Network

Management

Power

Assistant

Function

 Different user rights for each group, one user belongs to one group.
 The user right shall not exceed the group right.

 Support central server backup function in accordance with your configuration

and setup in alarm or schedule setting

 Support record via Web and the recorded file are storage in the client-end

PC.

 Support network storage function such as FTP.
 Real-time respond to external on-off alarm input, and video detect as user

pre-defined activation setup and generate corresponding message in screen
and audio prompt(allow user to pre-record audio file)

 Real-time video detect: motion detect, camera masking.
 Alarm occurs when network is abnormal.
 Network camera supports one-channel video data transmit to network

terminal and then decode. Delaying time is within 270ms (network bandwidth
support needed)

 Max supports 20 connections.
 Adopt the following video transmission protocol: HTTP, TCP, UDP,

MULTICAST, RTP/RTCP, RTSP and etc.

 Support web access.
 Realize network camera configuration and management via Ethernet.
 Support device management via web or client-end.
 Support abundant network protocol.
 External power adapter DC 12V.
 Support PoE.

Warning
Do not connect these two power supplying sources to the device at the
same time; it may result in device damage!

 Log function
 Support system resource information and running status real-time display.
 Day/Night mode auto switch.
 Support picture parameter setup such as electronic shutter and gain setup.

！！！！

1

 Support motion detect.
 Backlight compensation: screen auto split to realize backlight compensation

to adjust the bright.

 Support video watermark function to avoid vicious video modification.
 Built-in IR light. Support IR night vision.

1.3

1.3 Specification

Specificationssss

1.31.3

SpecificationSpecification

Please refer to the following sheet for network camera performance specification.

Model
Parameter

System

Video Parameter

Main Processor
OS
System

Resources
User Interface

System Status
Image Sensor
Pixel

Day/night

Gain Control
White Balance

BLC

Electronic
Shutter
Video
Compression
Standard

Video Frame
Rate

Video Bit Rate

Video Flip

Snapshot Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask
Video

Adjustment
Video
Information
Lens

Lens Interface

IPC-HDBW1000E-W DH-IPC-HDBW1200E-W

High performance DSP
Embedded LINUX
Support real-time network, local record, and remote operation at the

same time.
Remote operation interface such as WEB, DSS, PSS

Bit stream statistics, log, and software version.
1/4-inch CMOS 1/3-inch CMOS
1280(H)*720（V） 2048(H)*1536（V）

Support day/night mode switch

Fixed/Auto
Manual/Auto
Off/BLC/WDR (1-100 adjustable)/HLC(anti-flicker is outdoor and is valid

only when exposure mode is auto with range 1-100)
Manual/Auto
It ranges from 1/3 to 1/10000

H.264/H.264B/MJPEG H.264/H.264B/H.264H/MJPEG

PAL:
PAL:
Main stream (1280*720@25fps),
extra stream (704*576@25fps)

NTSC:
Main stream (1280*720@30fps),
extra stream (704*480@30fps)

H.264: 16Kbps-8192Kbps
adjustable.
MJPEG adjustable and bit rate is
adjustable.
Support customized setup
Support mirror.
Support flip function.

Supports max 4 privacy mask zones

Support parameter adjustment such as bright, contrast.

Channel title, time title, motion detect, camera masking.

2.8mm, 3.6mm, 6mm. Fixed focus.
M12. Lens is the default accessories

Main stream

(1920*1080@25fps),

extra stream

(704*576@25fps)

NTSC:

Main stream (1920*1080@30fps),

extra stream (704*480@30fps)

H.264H: 16Kbps-8192Kbps

adjustable

MJPEG adjustable and bit rate is

adjustable.

Support customized setup

2

Video

Motion Detect

Video Loss

Record

Network

Interface

General Parameter

Record Priority

Wire Network
Wireless

Network

Network Protocol

Remote
Operation

Access Protocol

AUX

Reset

WPS

Power

Power
Consumption
Working
Temperature
Working
Humidify

Dimensions(mm)
Weight
Installation

396 (18*22) detection zones; sensitivity level ranges from 0 to 100; area
threshold ranges from 0 to 100.
Activation event: video storage, image snapshot, log, email SMTP and
etc.

Activation event: video storage, image snapshot, log, email SMTP and
etc.

Manual >Video detect>Schedule

1-ch Enthernet port, 10/100 Base-T Ethernet

IEEE802.11a/b/g/n，built-in antenna

Standard
HTTP,TCP/IP,IPv4/IPv6,ARP,IGMP,ICMP,RTSP,RTP,UDP,SMTP,FTP,
DHCP,DNS,DDNS,PPPoE,UpnP,NTP,Bonjour,SNMP

Monitor, system setup, log information, maintenance , upgrade and etc

Support international, ONVIF

Built-in RESET button

WI-FI one key connection

DC12V

4.8W MAX 6.1W MAX

-30℃~+50℃

≤

95%

¢110×81
385g (Excluding box)
Ceiling and wall mount

3

2222 Structure

Structure

Structure Structure

2.1

2.1 Com

Component

ComCom

ponentssss

ponentponent

2.12.1

You can refer to the following figure for component structure. See Figure 2-1

Figure 2-1 Component structure

.

Please refer to the following sheet for detailed information.

2.2

2.2 Framework and Dimension

2.22.2

Please refer to the following two figures for dimension information. The unit is mm. See Figure 2-2 to
Figure 2-4

Component Component Name

Component 1 Dome body

Component 2 Dome enclosure

Port Port Name Note

Network data in/out and PoE.

Port 3 Dome enclosure

Port 4 Power input port

Framework and Dimension

Framework and DimensionFramework and Dimension

Note:

 Some devices do not

Connect to DC 12V power, input
power.

support PoE.

4

Figure 2-2 Dimension illustration (1)

Figure 2-3 Dimension illustration (2)

5

Figure 2-4 Dimension illustration (3)

6

3333 Device Installation

Device Installation

Device Installation Device Installation

3.1

3.1 Installation Steps

Installation Steps

3.13.1

Installation Steps Installation Steps

Important
Before the installation, please make sure the installation environments can at least support 3x

weight of the camera.

Please follow the steps listed below to install the device. Please refer to Figure 3-1 for reference.

Step 1

Use inner hex wrench in the accessories bag to open dome enclosure by unfastening three inner hex

screws on enclosure.

Step 2

Please take the installation position map in the accessories bag, and then paste it on the ceiling or the
wall according to your monitor area requirements.

Step 3

Find cross signs on the map, and dig three plastic expansion bolts holes in the installation surface and
then insert three expansion bolts in the holes. Secure these three bolts firmly.
Note:
 If use pulls out cable from top of installation surface, you must dig a exit hole on installation

surface according to the installation position map.

 If user pulls out cable from side of cable channel, it must go through the U-shape channel on

dome pedestal, and take out cable from the side exit hole on pedestal.

Step 4

Adjust the device installation pedestal to the proper position and then pull cable through the exit hole
on Installation surface. Make direction of TOP sign same as it on installation position map. Line up the

three screw holes in the device pedestal to the three plastic expansion bolt holes in the installation
position. Put the three self-tapping screws in the three plastic expansion bolts firmly. Fix dome body on
installation surface.

Step 5

Hold bottom of bracket with hand, horizontally rotate bracket, adjusting lens direction to designated

position. Loosen one M2 screw on LED decoration cover (loosen only, do not take it down), hold the
decoration cover with hand, making lens rotate vertically. Adjust vertical direction of lens to appropriate

angle, and fasten the M2 screw. Range of lens: vertical (0°～+65°), horizontal (0
Figure 3-2.

°～

+355°). See

7

Figure 3-1 Device installation illustration 1

Figure 3-2 Device installation illustration 2

8

Note:

When you need to reset the device, press the “Reset” button in Figure 3-2 for 10 seconds while
connecting device to power.
When you need to use WPS function, press the “Reset” button in Figure 3-2 for 1 to 2 seconds while
connecting device to power, then press WPS button on the router. Generally the device can be
connected to corresponding router within 1 minute (supported by some series products).

Step 6

Take dome enclosure, put it back on the camera properly regarding to screw and hole, and fasten the
three inner hex screws with wrench.

9

4 Quick Configuration Tool

4.1 Overview

Quick configuration tool can search current IP address, modify IP address. At the same time, you can
use it to upgrade the device.

Please note the tool only applies to the IP addresses in the same segment.

4.2 Operation

Double click the “ConfigTools.exe” icon, you can see an interface. In the device list interface, you can
view device IP address, port number, subnet mask, default gateway, MAC address and etc.

Select one IP address and then right click mouse, you can see an interface is shown as in figure 4-1
Select the “Open Device Web” item; you can go to the corresponding web login interface.

Figure 4-2 Search interface

If you want to modify the device IP address without logging in the device web interface, you can go to
the configuration tool main interface to set.

In the configuration tool search interface (Figure 4-2), please select a device IP address and then
double click it to open the login interface. Or you can select an IP address and then click the Login
button to go to the login interface. See Figure 4-3.
In Figure 4-3, you can view device IP address, user name, password and port. Please modify the
corresponding information to login.

Please note the port information here shall be identical with the port value you set in TCP port in Web
Network interface. Otherwise, you cannot login the device.
If you are using device background upgrade port 3800 to login, other setups are all invalid.

10

Figure 4-3 Login prompt

After you logged in, the configuration tool main interface is shown as below. See Figure 4-4.

Figure 4-4 Main interface

For detailed information and operation instruction of the quick configuration tool, please refer
to the Quick Configuration Tool User’s Manual included in the resources CD.

11

address

here

5 Web Operation

This series network camera products support the Web access and management via PC.
Web includes several modules: Monitor channel preview, system configuration, alarm and etc.

5.1 Network Connection

Please follow the steps listed below for network connection.

 Make sure the network camera has connected to the network properly.
 Please set the IP address, subnet mask and gateway of the PC and the network camera

respectively. Network camera default IP address is 192.168.1.108. Subnet mask is 255.255.255.0.
Gateway is 192.168.1.1

 Use order ping ***.***.***.***(* network camera address) to check connection is OK or not.

5.2 Login and Main Interface

Open IE and input network camera address in the address bar. See Figure 5- 1.

Input your IP

Figure 5- 1 IP address

The login interface is shown as below. See Figure 5- 2.
Please input your user name and password.

Default factory name is admin and password is admin.

Note: For security reasons, please modify your password after you first login.

12

Figure 5- 2 Web login

After you successfully logged in, please install WEB plug-in unit. Please refer to the Web Operation

Manual included in the resource CD for detailed operation instruction.
See Figure 5- 3.

Figure 5- 3 Web monitoring window

13

6666 FAQ

FAQ

FAQFAQ

Bug

I can not boot up
the device or
operate properly.

I can not upgrade
the device via
network.

I can not login the
client-end or the
WEB.

I can not play the
download file.

Please click RESET button for at least 10 seconds to restore factory
default setup.

When network upgrade operation failed, you can use port 3800 to
continue upgrade.

For Windows OS 98 or Windows ME user, if you can not install the
client-end or can not view after the installation. We recommend the
win2000sp4 OS or install the client-end of the low version.

The Active X control is blocked.

The display card version shall be dx8.1 or higher.

Network connection error occurred.

Invalid network setup.

Invalid user name or password.

There is no player.

There is no DX8.1 or higher.

For the MEDIA PLAYER, there shall be Div X503Bundle.exe plugin
if you play the .AVI file.

For Windows XP user, you need to install the plugin
DivX503Bundle.exe and ffdsho-2004 1012.exe.

To guarantee
setup update

Power adapter

After you modified the important setup, please reboot the device via
the software to make sure the setup has been updated to the
storage medium.

The general power adapter can work ranging from 0℃ to 40 ℃. The
device may result in unstable power supply when the temperature
exceeds the working temperature.

Please replace an industry-level power adapter if you are using in
the harsh environments.

14

Appendix

Appendix Toxic or Hazardous Materials or Elements

Appendix Appendix

Toxic or Hazardous Materials or Elements

Toxic or Hazardous Materials or ElementsToxic or Hazardous Materials or Elements

Component

Name

Circuit Board

Component

Device Case ○ ○ ○ ○ ○ ○

Wire and Cable ○ ○ ○ ○ ○ ○

Packing

Components

Accessories ○ ○ ○ ○ ○ ○

O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the
parts is below the relevant threshold of the SJ/T11363-2006 standard.

X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous
materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. During the
environmental-friendly use period (EFUP) period, the toxic or hazardous substance or elements
contained in products will not leak or mutate so that the use of these (substances or elements) will not

result in any severe environmental pollution, any bodily injury or damage to any assets. The consumer
is not authorized to process such kind of substances or elements, please return to the corresponding
local authorities to process according to your local government statutes.

Note

Pb Hg Cd Cr VI PBB PBDE

○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○

Toxic or Hazardous Materials or Elements

 This user’s manual is for reference only. Slight difference may be found in user interface.

 All the designs and software here are subject to change without prior written notice.

 All trademarks and registered trademarks mentioned are the properties of their respective

owners.

 If there is any uncertainty or controversy, please refer to the final explanation of us.

 Please visit our website for more information.

Zhejiang Dahua Technology CO., LTD.

Address：No.1199 Bin’an Road, Binjiang District, Hangzhou, PRC.
Postcode: 310053
Tel: [phone]
Fax: [phone]
Email:[e-mail]
Website: www.dahuatech.com

15

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.

IEEE 802.11b or 802.11g or 802.11n(HT20) operation of this product in the U.S. is
firmware-limited to Channel 1 through 11. IEEE 802.11n(HT40) operation of this product
in the U.S. is firmware-limited to Channel 3 through 9.

16