1.2 .51.3 2.135 87- 000
Package content Over view Mounting PoE
x1 x1
Mounting Part ETH+PoE
x1 x1 x1
RSSI LEDs
LAN LED
Power LED
Device cable gland must be positioned vertically downwards
- 01 - - 02 - - 03 - - 04 - - 05 -
to protect it against water ingress.
Note
Installation Requirements
Shielded Category 5 (or above) cabling should be used for all wired Ethernet
con nectio ns and groun ded throu gh AC grou nd of PoE. For all ou tdoor
installations, we recommend that you use Ethernet Surge Protectors near the
device, which will absorb power surges and discharge them into the ground.
Default Login
IP address
DHCP client
(Fallbac k IP: 192.168.1 .36)
Parameters
Model name
Frequency
Tx power
EIRP
Antenna gain
Power supply
Power consumption
settings
Connection
Login
Username : admin
Passwor d: admin
DH-PFWB5-10n
5.150-5.250GHz 5.725-5.850GHz
-
Up to 13 dBm
(country
dependent)
36 dBm
(country
dependent)
20dBi
24V DC
passive
4.5W
Configuration Steps
Precondition
Please ens ure that PC has been connect ed with LAN port of PoE power
of wireles s device.
IP addres s of PC and IP address of the devic e (default one is 192.168.
1.36) are set to be in the same network segmen t.
Operating
Step 1
Open Internet Explor er, input default I P address of wireles s device in the
addres s bar and press [Enter] key.
Steps
PoE
Step 2
Input the usern ame and password, and click “L ogin”.
The system disp lays the following inte rface, as shown in Fig ure 1-2.
Note
Default username and password are admin. It is suggested that a password
with high security should be set and password should be modified regularly.
Fig ure 1-1
Step 3
Tick “I have read and agree”, select operat ing country and click “Change”.
The system displays the follo wing interface, as shown in Figure 1-3.
Fig ure 1-2
Fig ure 1-3
Wireless Access Point
Step 4
Cli ck “Sett ings > Wi reless C onfig urati on”, a s shown in F igure 1- 4. Set
frequ ency and ch annel ; set the wirele ss opera ting mode t o be Access
Point (auto WDS) . There are 5 operating modes: Access Point (auto WDS),
Configuration:
- 06 - - 07 - - 08 - - 09 - - 10 - - 11 -
Wirele ss Acce ss Poin t (TDMA 2), Acc ess Poi nt (TDMA 3), Sta tion (WD S/
TDMA2 /TDMA3) . Cl ick setti ng icon at the l ower righ t corner of SSID, set
SSID and securi ty info, and clic k “Done”, as shown in Fi gure 1-5.
Note
There is no occ lusion between the dev ices
The device connected with camera is set to be “Station (WDS/TDMA2/
TDMA3)” mode.
The device connected with machine room is set to be "Access Point
(Auto WDS)" mode.
Please select WDS mode for transparent transmiss ion of data.
Step 5
Click “Sa ve Changes” at the top right corne r as shown in Figure 1-6 , and
then clic k “Save” as shown in Figur e 1-7.
Fig ure 1-6
Fig ure 1-4
Fig ure 1-5
Station
Step 6
Click “ Settings > Wireless C onfiguratio n”, as show n in Figur e 1-8; selec t
operating mode to be “Station (WDS/TDMA2/TD MA3)”. Click setting icon
at the lower righ t corner of SSID, as show n in Figure 1-9. Click "R efresh"
icon at the top right corn er. Search SSID of acce ss point, click “Sel ect”,
enter SSI D passphrase and click “D one”, as shown in Figure 1-10.
Configuration
Fig ure 1-7
Step 7
Select “Network Configura tion”, and modify IP address to be 192.168.1.37
as shown in Figure 1-11, in order to avoid IP conflict. Click “Save” at the
Fig ure 1-8
Fig ure 1-9
Fig ure 1-1 0
top right corner, as shown in Figure 1-12, and click “Done”. It displays
normal connection status, as shown in Figure 1-13.
Fig ure 1-1 1
Fig ure 1-1 2
Fig ure 1-1 3
Important Safeguards and Warnings
The follow ing descrip tion is the c orrect appl ication met hod of the de vice.
Pleas e read the man ual care fully be fore use, i n order to preve nt dange r
and prop erty los s. Strict ly confor m to the man ual duri ng appli cation and
keep it properly aft er reading.
Operating
Please don’t drip or splash liquids onto the device; don’t put on the device
anythin g filled with liqu ids, in order to prevent liquids f rom flowin g into
the device.
Use the device only within rated input and outpu t range.
Please don ’t dismantl e the device arbit rarily.
Please transport, use and store the device wit hin allowed humid ity and
temper ature range.
About this
The Manual is for reference only. I f there is incon sistency between the
Manua l and the actual produ ct, the actual product shal l prevail.
We are not liable for any loss caused by the operations that do not comply
with the Manual .
The Manual would be updated according to the latest laws and regulations
of related regions. For detailed information, see the paper User's Manual,
CD-RO M, QR code or our o fficial websit e. If ther e is incon sistency
betwee n paper User's Manua l and the electroni c version, the electr onic
versio n shall prevail.
All the desig ns and softwar e are subject to change w ithout prior written
notice. The product updates mi ght cause some differences between the
actual product and the Man ual. Please co ntact the custo mer service for
the latest progra m and supplement ary documentat ion.
There still might be deviation i n technical data, functions and operatio ns
description, or errors in print. If there is any do ubt or dispute, please refer
to our final expl anation.
Upgrad e the reader soft ware or try other mainstrea m reader sof tware if
the Guide (in PDF format) can not be opened.
Requirement
Document
Regulatory Information
Th e reg ula tory i nfo rmat ion h erei n mig ht va ry acc ord ing to t he
mod el you p urc has ed. S ome i nfo rma tio n is on ly ap pli cab le for
the c ount ry or re gion w here t he pro duct i s sold .
FCC Information
CAUTION
Cha nges or m odifi catio ns not ex pre ssl y app rov ed by t he pa rty
re spo nsi ble f or co mp lia nce c oul d voi d the use r's a uth orit y to
ope rate th e equip ment.
FCC c ondit ions:
Thi s devic e com pli es wi th pa rt 15 o f the FC C Rules . Opera tion
is sub ject to th e follo wing two c ondit ions:
This dev ice may not cau se harm ful int erfer ence.
This d evic e must a ccep t any i nter fere nce re cei ved, i nclu ding
inte rfere nce tha t may caus e undes ired ope rati on.
FCC c ompli ance:
Th is eq uipm ent h as bee n test ed an d foun d to com ply wi th t he
lim its f or a dig ital de vice , pursu ant to p art 15 of t he FCC R ule s.
This equ ipment gen erates, us es, and can radi ate radio fre quency
en erg y an d, i f not i nst all ed a nd us ed i n acc ord an ce w ith t he
inst ructi ons, ma y cause ha rmfu l inter feren ce to radi o
comm unica tion .
For cl ass A devi ce, the se limi ts are des igned t o provi de
reas onabl e prote ctio n agains t harmf ul inte rfere nce in a
co mme rcia l env iro nmen t. Op era tion o f thi s eq uip ment i n a
resi dentia l area is like ly to cause ha rmful in terfer ence in whi ch
case t he user wi ll be requ ired to co rrec t the inte rfere nce at his
own ex pense .
For cl ass B devi ce, the se limit s are des igned to p rovid e
reas onabl e prote ctio n agains t harmf ul inte rfere nce in a
res ident ial in sta lla tio n. Ho wev er, th ere i s no gu ara nte e tha t
in ter fer ence w ill no t oc cur i n a part icul ar in stal lat ion. I f this
equ ipme nt doe s cau se har mful i nter ferenc e to ra dio or
tel evi sion r ece ptio n, wh ich ca n be det ermin ed by tu rnin g the
equ ipme nt off an d on, the u ser is en cour aged t o try to co rrec t
th e int erfe renc e by on e or mo re of t he fo llow ing me asur es:
Reorient or relocat e the receiving antenna.
Increas e the separation be tween the equipm ent and receiver.
Con nect t he eq uip men t int o an ou tlet on a c ircu it di ffe ren t
from that to which the receiver is connecte d.
Consu lt the deale r or an experie nced radi o/TV tech nician fo r
help.
SDOC Sta tement: ht tps://u s.dahu asecuri ty.com/su pport/ notices /
Privacy Protection Notice
As the device user or data controller, you might collect personal data
of others such as face, fingerprints, car plate number, Email address,
phone numb er, GPS and so on. You need to be in compliance wit h
the l ocal pr iva cy pr ote cti on la ws an d reg ula tion s to prot ect the
leg iti mate r ights a nd int ere sts of o ther pe ople b y imp leme nting
mea sur es inc lude bu t not li mited t o: pro vidin g cle ar and v isi ble
iden tific ation t o inform da ta subj ect the ex isten ce of surv eilla nce
area and providing related contact.
Please take attention that changes or modification n ot expressly
approved by the party responsible for co mpliance could void the
user’s authority to operate the equipment.
This equipment complies with FCC/IC RSS-102 radiation exposure
limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm
between the radiator & your body.
1.2 .51.32 .1368 8-00 0
Loading...