Page 1
Dahua K Series Cube Network Camera Quick Start Guide
V 1.0.0
Dahua Technology CO., LTD
Page 2
1111 Packing List
Packing List
Packing List Packing List
Device × 1 QSG ×1
Power Adapter ×1 Screw Package ×1
Installation Position Map ×1
1
Page 3
2222 Product Appearance
Product Appearance
Product Appearance Product Appearance
Figure 2-1 Figure 2-2
Figure 2-3
Please refer to the following sheet for more details about each port.
SN Name
1 Network port
2 Reset/WPS button
3 Digital input/output
4 Power port
5 Built-in speaker
2
Page 4
Note:
For reset, long press for 8 seconds and then the light off; For WPS, one quick press.
Please refer to the following sheet for more details about status of indicator light.
6 Micro SD card slot
7 Indicator light
8 Built-in MIC
9 IR LED
10 PIR
Sheet 2-1
Indicator light status Device status
Red light normally on Booting
Green light slow flashing Booting completed, await wifi config, enter smart
config status;
Green light quick flashing
Green light normally on Wifi connection succeeded, operate normally.
Red and green lights flash
alternately
Red light slow flashing Network connection failure or disconnection after
Red light quick flashing Device malfunction, fail to boot up; alarm or SD card
Wifi smart config in progress, including WPS,
management frame and etc.
Device upgrade
network connection success.
malfunction
Sheet 2-2
3
Page 5
Operate by Easy4ip
Operate by Easy4ip Operate by Easy4ip
Operate by Easy4ip
Power on the device with power adapter.
phone to your WiFi network.
Easy4ip APP
IOS
“Easy4ip APP”
, see
3333
1.
2. Connect your smart
download and install the
3. Open Easy4ip APP (take
APP
APP
APPAPP
Scan the
.
as an example), tap login to login the APP
QR on the packing box,
Figure 3-1.
4. Tap “register” for first use.
Figure 3-1
4
Page 6
5. Tap “+” to add devices.
Figure 3-2
6. Choose “Wireless”.
Figure 3-3
5
Page 7
Figure 3-4
7. Name the camera and scan the QR code on camera.
6
Page 8
8. Input the Wi-Fi password.
Figure 3-5
Figure 3-6
7
Page 9
9. Waiting for 60s to finish the Wi-Fi connection.
Figure 3-7
Note: If you want to change the Wi-Fi signal, please reset the camera to factory default and repeat
step 6-9;
Figure 3-8
8
Page 10
4444 Operate
Operate by DMSS APP
Operate Operate
Step 1
Power on the camera.
Step 2
Connect iphone to a WiFi signal.
Step 3
Open DMSS (downloaded from APP Store), choose Device Manager.
by DMSS APP
by DMSS APPby DMSS APP
Step 4
Click “+”.
Figure 4-1
9
Page 11
Step 5
Choose “WiFi configuration”.
Figure 4-2
Figure 4-3
Step 6
Input a device name and scan the QR code on camera, then “next”.
10
Page 12
Step 7
Input the WiFi password, then “next”.
Figure 4-4
Step 8
Connection succeeds.
Figure 4-5
11
Page 13
6 Figure 4
Please try again or check the WiFi password if it failed.
The WiFi configuration will be closed if activat
need to configure WiFi via DMSS App.
7 Figure 4
Please reset
Note:
Figure 4-
-
ing WPS function,
-8
the device if you still
12
Page 14
5
5 Device Installation
Device Installation4
5 5
Device InstallationDevice Installation
The IP address of all the cameras is the same when leaving factory (default IP 192.168.1.108). To
make the camera access to the network smoothly, please plan the available IP segment reasonably
according to the actual network environment.
NOTE:
The camera can be configured only when the IP addresses of the camera and the computer are in the
same network segment.
Step 1
Power on the device with power adapter,Connect the device to computer.
Step 2
Double click the “smart cms.exe”，The user name and password are admin and admin .
Shown in Figure 4-1.
4 Network Configuration
Network Configuration
4 4
Network Configuration Network Configuration
Figure 4-1
Step 3
Click , and then click to enter the interface where you can find IP
address.Shown in figure 4-2.
Input your username and password (Default username is admin and password is admin respectively).
Figure 4-2
13
Page 15
Step 4
Click ,and double click the default IP, See Error! Reference source not found. for
the main interface.
Error! Reference source not found.
Dahua A Series HD Wi-Fi Network Camera
Quick Start Guide
14
Page 16
6666
Important
Please make sure the installation surface can min support the 3X weight of the camera and the
bracket.
Figure 5-1
Step 1
Paste the installation map on the installation surface such as wall, ceiling or the wood.
Step 2
Dig holes in the installation surface according to the installation map.
Step 3
Insert the expansion bolts from the accessories bag to the holes you just dug. If it is the wood surface
you can skip to the next step.
Step 4
Fix the device with screw in the accessories bag.
Step 5
Connect the cable and then boot up the device.
Step 6
Loosen the adjust knob for a little bit, adjust the camera to proper surveillance position according to
your practical requirements.
Step 7
Secure the knob of the bracket to fix the camera.
15
Page 17
7777
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Attention that changes or modification not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note: This product has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This product generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this product does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm between the
radiator and your body
Dahua Technology Co., Ltd
Address：No.1199 Bin’an Road, Binjiang District, Hangzhou, PRC.
Postcode: 310053
Tel: +86-571-87688883
Fax: +86-571-87688815
Email:overseas@dahuatech.com
Website: www.dahuasecurity.com
16
Loading...