Januar y 20 02
Please Kee p Ma nual with th e Device!
Part # Z6000-0001
MAN-Z3K-01
Revision 1.0
Zeta Alarm Systems Ltd.
A division of
GLT Exports Ltd
72-78 Morfa Road
Swansea SA1 2EN
U.K.
http://www.zeta-alarms.co.uk
nrpj@zeta-alarm s .fsworld.co.uk
Page 2 of 2
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page i
Table of Contents
1. Preliminary Information ................................ ......... ......... .......... ......... ............... 1
1.1 What Is In This Manual? ................................................................................................... 2
1.2 System Overview ..... .................................................. .................................................. ..... 3
1.2.1 List of Standard Features .................................................................................... 3
1.2.2 List of Optional Features ...................................................................................... 4
1.2.3 List of Network Features ...................................................................................... 4
1.3 Agency Approvals and Listings ......................................................................................... 6
1.3.1 Specific UL Requirements ................................................................................... 7
1.3.1.1 Local Protecte d Fi re Alarm Systems .......... ......................................... 7
1.3.1.2 NFPA 72 Central Station – Networked Digital Communicator (ZNDC) 7
1.3.1.3 NFPA 72 Remote Station –N etworked Digit al Communicator (ZNDC) 7
1.4 Technical Specifications .......................... ..................................................................... ..... 8
1.4.1 Power Supply ....................................................................................................... 8
1.4.2 Battery Charger ................................................................................................... 8
1.4.3 Notification Appliance Circuits/24VDC Auxiliary Outputs .................................... 8
1.4.4 SLC Specifications ............................................................................................... 8
1.4.5 Syste m and Auxiliar y R e l ay Outpu t s . . .. .... . .. .... . .. .... . .... . .. .... . .. .... . .. .... . .... . .. .... . .. .... 8
1.4.6 RS-485 Network .................................................................................................. 9
1.4.7 Communication/Printer Ports - ZSCP3/ZICP ....................................................... 9
1.4.8 Wiring Specifications and Requirements ........................................................... 10
1.4.8.1 General Specifications ....................................................................... 10
1.4.8.2 SLC Wire Specifications .................................................................... 10
1.4.8.3 Network Wiring .................................................................................. 11
1.4.9 Calculating Maximum Current Draw and Battery Backup Requirements .......... 11
1.5 Before You Begin Installing.............................................................................................. 12
1.5.1 System Architecture and Overview .................................................................... 12
1.5.1.1 Adding Remote ACMs ....................................................................... 12
1.5.2 Point Programming Ov erview ............................................................. ............... 13
1.5.2.1 SLC Devices, Bases, and Accessories .............................................. 13
1.5.2.2 Global Input Programming Options ................................................... 13
1.5.2.3 System Timing Options ..................................................................... 14
1.5.2.4 Input Point Programming ................................................................... 14
1.5.2.5 SLC Output Point Programming ........................................................ 14
1.5.2.6 Output Groups ......... .............................. ............................................ 14
1.5.3 City Box and Reversing Polarity Interface .......................................................... 15
1.5.4 System Auxiliary Relays .................................................................................... 15
1.5.5 Sy ste m Cont r o l Hot Keys ...... ............................... ............................... ............... 15
2. Installation Procedures
....................................................................................................
17
2.1 What Do I Have .............................................................................................................. 17
2.2 Installation Sequence ..................................................................................................... 17
2.2.1 Mount Enclosure ................................................................................................ 19
2.2.2 I ns ta ll CP3 Board ......... ............................... ................................................. ...... 19
2.2.3 Mount Chassis in Enclosure .............................................................................. 19
2.2.4 Connect AC Power ............................................................................................. 20
2.2.5 Connect Batteries .............................................................................................. 20
2.2.6 Install Optional ZZRM Auxiliary System Relays .............................. ..... ....... ..... . 21
2.2.7 Install Optional Modules .................................................................................... 21
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page ii
2.2.8 Power Limited Wire Routing .............................................................................. 21
2.3 Wiring the Signaling Line Circuits (SLCs) ....................................................................... 22
2.3.1 SLC Device Capacity ......................................................................................... 22
2.4 Sensor Base Wiring ........................................................................................................ 22
2.5 Installing SLC Devices .................................................................................................... 25
2.5.1 NFPA Wiring Styles ............................................................................................ 26
2.5.2 Input Modules .................................................................................................... 29
2.5.3 XP95A Switch Monitor Module/ XP95A Priority Switch Monitor Module ........... 30
2.5.4 I/O Relay – I/O Input Module* ............................................................................ 31
2.5.5 Sounder Control Module .................................................................................... 32
2.5.6 Sounder Base/Relay Base . ................................................................................ 33
2.6 CP3 Wiring Terminal Identification .................................................................................. 34
2.6.1 Network Wiring .................................................................................................. 35
2.6.2 NAC Wiring ........................................................................................................ 36
2.7 System and Auxiliary Relays .......................................................................................... 37
2.7.1 ZZRM Auxilia ry Relays ...................................................................................... 37
2.7.1.1 Multiple ZZRM Relay Installation ....................................................... 38
2.8 Conventional Zone Input Capabilities ............................................................................. 38
2.9 Printer Output Options .................................................................................................... 38
3. System Controls and Operation
...................................................................................
39
3.1 System Display and Annunciation ................................................................................... 39
3.1.1 LCD Screen ....................................................................................................... 39
3.1.2 LED Indicators ................................................................................................... 39
3.1.3 Panel Control Keys ............................................................................... ............. 40
3.1.4 Function Keys .................................................................................................... 40
3.1.5 Alphanumeric Keypad . ....................................................................................... 40
3.2 System L ED Indi ca tors .......... ......................................... ........................................ ........ 40
3.2.1 Alarm ................................................................................................................. 40
3.2.2 Trouble ............................................................................................................... 41
3.2.3 Supervisory ....................................................................................................... 41
3.2.4 Silenced ............................................................................................................. 41
3.2.5 AC Power ........................................................................................................... 41
3.2.6 Offline ................................................................................................................ 41
3.2.7 Test Mode .......................................................................................................... 41
3.3 Function Keys ................................................................................................................. 41
3.3.1 Programming (PROG) ....................................................................................... 41
3.3.2 Status ................................................................................................................. 42
3.3.3 Test .................................................................................................................... 42
3.3.4 Print ................................................................................................................... 42
3.3.5 Drill .................................................................................................................... 42
3.3.6 Programmable Input Keys .................................................................................. 43
3.4 System Operating Modes and Annunciation .................................................................. 43
3.4.1 Normal Operation .............................................................................................. 43
3.4.2 Trouble Operation .............................................................................................. 43
3.4.3 Silence Operation .............................................................................................. 44
3.4.4 Ala rm Oper at ion .................................... ........................................ .................... 44
3.4.5 Supervisory Operation ....................................................................................... 45
3.4.6 Program Mode Operation .................................................................................. 46
3.4.7 Test Mode Operation ......................................................................................... 46
3.4.8 Sleep Mode ........................................................................................................ 47
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page iii
3.4.9 Watchdog Circuit Operation ............................................................................... 47
3.5 Notification Appliance Circuit (NAC) Operation .............................................................. 47
3.6 Addressable Sensor Functions ....................................................................................... 47
3.6.1 Analog Display ................................................................................................... 47
3.6.2 Sensitivity Adjustment ........................................................................................ 48
3.6.3 Day/Night Sens i tivity Adjustme n t ....................................... ................................ 48
3.6.4 Ala rm Test Level M e as urement .................. ................................................. ...... 48
3.6.5 Automatic Test Operation ................................................................................... 48
3.6.6 Maintenance Alert Operation .. ........................................................................... 48
3.6.7 Type Code Supervision ...................................................................................... 48
3.6.8 LED Control Operatio n ...................................................................................... 48
3.6.9 Ala rm Verification Operatio n .............................. ........................................ ........ 48
3.7 Addressable Module Operation ...................................................................................... 49
3.7.1 Contact Monitor Module ..................................................................................... 49
3.7.2 I/O Module ......................................................................................................... 49
3.7.3 Sounder Output/Sounder Co ntrol Modul e . ........................................................ 49
3.8 Network Operation .......................................................................................................... 49
3.9 Zeta Zone Relay Module (ZZRM) Operation .................................................................. 50
3.10 Zeta Serial and Isolated Com munication Ports (SCP3 / ICP) Operation ........................ 50
4. System Prog ra mm ing
.......................................................................................................
51
4.1 Before You Begin Programming ...................................................................................... 51
4.1.1 Access Privilege Code (APC) ............................................................................ 51
4.2 Program Menus .............................................................................................................. 52
4.2.1 Clock .................................................................................................................. 52
4.2.2 System ............................................................................................................... 53
4.2.2.1 System Options ................................................................................. 53
4.2.2.2 Timing ................................................................................................ 54
4.2.2.3 Access Pri v ilege Codes . .................................................................... 55
4.2.2.4 Edit Banner Message .... .................................................................... 55
4.2.3 Network .............................................................................................................. 56
4.2.4 Configuring Inputs ............................................................................................. 56
4.2.4.1 Input Options ..................................................................................... 57
4.2.4.2 Alarm Sensitivity Levels ..................................................................... 57
4.2.4.3 Input Aler t s ........................................................................................ 57
4.2.5 Configuring System Outputs .............................................................................. 58
4.2.5.1 Notification Appliance Circuits (NACs) .............................................. 58
4.2.5.2 Zeta Zone Relay Modules (ZZRMs ) .................................................. 58
4.2.6 Point Programming ........... .............................. ......................................... .......... 58
4.2.6.1 Auto-Program .................................................................................... 59
4.2.6.2 Add/Remove Point ............................................................................. 60
4.2.6.3 Point Location .................................................................................... 60
4.2.6.4 Point Programming Options - Edit ..................................................... 60
4.2.6.5 Point Programming Options - Browse ................................................ 61
4.2.6.6 Point Programming Options - Status ................................................. 61
4.2.7 Output Group Programming .............................................................................. 61
4.2.7.1 Browse Group .................................................................................... 62
4.2.7.2 Edit Group ......................................................................................... 62
4.2.8 PC Communications .......................................................................................... 63
4.2.9 Factory Defaults ................................................................................................. 63
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page iv
5. Special Application Programming and Operation
................................................
65
5.1 Local Protective Signaling System ................................................................................. 65
5.2 NFPA 72 Central Station ................................................................................................. 65
5.3 NFPA 72 Remote Station ................................................................................................ 65
5.4 Special Output Group Operation .................................................................................... 65
5.4.1 Waterflow Point Programming ........................................................................... 66
5.4.2 Supervisory Point Programming ........................................................................ 66
5.4.3 Rem ote Key Reset/Silence ............ .... . .... ........ ......... ........ ............. .... . .... .... . .... ... 67
5.4.4 Floor Above/Floor Below .................................................................................... 67
5.5 Time Control Operations ................................................................................................. 68
5.6 Program Your Own Applications ..................................................................................... 69
6. Netwo rking / Serial D e vices
...........................................................................................
71
6.1 Serial Devices ................................................................................................................. 71
6.1.1 Zeta Remote Display Annunciator (ZRDA) ........................................................ 71
6.1.2 Conventional Initiating Zone Expansion ............................................................. 71
6.1.2.1 ZFZA/ZTZB ........................................................................................ 71
6.1.2.2 Dual Input/Output Module .................................................................. 72
6.1.2.3 Panel Network Interface (ZPNI) ......................................................... 72
6.1.3 SLC Loop Expansion Using the ZRPC and ZACM ............................................ 72
6.1.4 ZRL D Remote LED Driv er ....... ..................... ........................................ ............. 72
6.1.5 ZCBM City Box/Reversing Polarity Module ........................................................ 74
6.1.6 Networked Digital Communicator (ZNDC) ......................................................... 74
6.2 Serial Device Configuration ............................................................................................ 75
6.3 Supervision . .................................................................................................................... 75
6.4 Addressing Serial Devices .............................................................................................. 76
6.4.1 ZACM Addressing .............................................................................................. 76
6.4.2 ZTZ B/ZFZA DIP Switch Configurati o n ...................................... ......................... 77
6.4.3 ZRL D DIP Switch Conf igu ration ....... ..................... ............................... ............. 78
6.4.4 ZRDA Addressing .............................................................................................. 78
6.4.5 ZRL D Network Addresses .......................................... ....................................... 79
6.4.6 ZCBM Netw o rk Addre sse s ....................................... ............................... .......... 79
6.4.7 ZPNI DIP Switch Configuration .......................................................................... 80
6.5 Serial Device Technical Specifications ........................................................................... 80
6.5.1 ZTZ B/ZFZA Specificati o n s ................................... .............................................. 80
6.5.2 Power Requirement - ZRDA .............................................................................. 81
6.5.3 Power Requirement - ZRLD ............................................................................... 81
6.5.4 Power Requirement - ZPNI ................................................................................ 82
6.6 Wiring Block Diagrams ................................................................................................... 82
6.6.1 Wiring Block for ZFZA/ZTZB, ZRLD Network Devices ....................................... 82
6.6.2 Wiring Block for ZRPC, ZCBM, ZRDA Network Devices ................................... 83
6.6.3 Wir i n g Block fo r ZDIO Network Devices ................................................ ............ 83
6.7 Serial Device Enclosure Installation Procedures ............................................................ 84
6.7.1 Serial Device Enclosure Installation .................................................................. 84
6.7.2 Sin g le Device Installa tion ..................................... ........................................ ...... 84
6.7.2.1 Dual Device Installation ..................................................................... 84
6.7.3 Installation of ZACMs ......................................................................................... 84
6.7.3.1 Adding a Second ZACM .................................................................... 84
Appendix A: Classic 2000 Mk II Part Number/Orderin gInformation ...................... 85
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page v
Appendix B: Class ic 2000 Mk II Battery Backup Calculation ................................. 86
Appendix C-1: 24VDC Notification Circuit Compatible Devices ............................. 88
Appendix C-2: Two-wire ZTZB/ZFZA Smoke Detector Compatibility ..................... 89
Appendix C-3: Compatible SLC Devices and Accessories ..................................... 90
Appendix D: Classic 2000 Mk II BASIC OPERATING INSTRUCTIONS ................... 91
Appendix E: Classic 2000 Mk II Programming Menus ............................................. 92
Appendix F: ZNDC Wiring Diagram ................................. ......... .......... ....................... 98
Appendix G: Input Point Record ................................................................................ 99
Appendix H: Glossary of Terms ............................. ......... ........................................ 103
Appendix H-1: Glos sary of Acron yms ..................................... ............................... 104
Appendix I: Analog Value Conversion Table .......................................................... 105
Appendix J-1: X-Pert Card (Sensor Base) Addressing .......................................... 107
Appendix J-2: Dip Switc h Addressing ............................................... ..................... 108
Appendix K: Printing Operation ............................................... ............................... 109
Appendix L: Mapping Operation .............................................. .......... ......... ............ 110
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 1
1. Preliminary Information
!! IMPORTANT !!
Please read before proceeding!
The equipment described in this manual is listed by Underwriters Laboratories, Inc. for use in fire alarm
signaling systems, only when installed in accordance with this manual and the latest National Fire Protection Association Standards 72 and 90A; the National Electrical Code (NFP A 70); th e Life Safety Code
(NFPA 101); and/or the local authority having jurisdiction (AHJ).
It is possible to apply system components incorrectly or arrange system components and installation wiring
so that required life safety functions are NOT performed. As a result, lives may be lost.
To minimize this possibilit y:
DO NOT
deviate from any installation instr uctions contained in this manual.
DO NOT
assume any installation details not shown in this manual.
DO NOT
alter any mechanical or electrical features of the equipment sup plied
BE FAMILIAR
with the building code, fir e prevention code, and/or require ment s of the A uth ority Hav -
ing Jurisdiction (AHJ) in the locale of the install ation.
WARNING!
Under normal and fault conditions, AC line voltages may be present on any ter minal. Touching any component could be hazardous and result in loss of life. A short circui t can result in arcing that could cause molten metal injuries to testing personnel.
To minim ize th is pos s ibility, only qualif ied electrical technicians familiar with electrical hazards should perform these checkout procedures. Safety glasses should be worn by such per sonnel, and instruments used
for voltage measurement should be designed for the purpose and should be in good mechanical and working order.
If there is application or i nstallation information that is not clear or not covered i n th is manual, plea se contact us at:
How To Contact Zeta Alarm Systems
World Wide Web:http://www.zeta-alarms.co.uk
Internet E-Mail:nrpj@zeta-alarms.fsworld.co.uk
Phone:+44 1792 -470394 or +44 1792 455175
FAX:+44 1792 455176
Snail Mail:Zeta Alarm Systems
72-78 Morfa Road
Swansea SA1 2EN
U.K.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 2
1.1 What Is In This Manual?
The Classic 2000 Mk II is the most intelligent fire alarm control system ever supplied by Zeta Alarm Systems. This analog addressable sys tem gives the installer and the end user the most versatile, easy to use
life safety system availab le to date. One of the most important features of this new technology panel is that
the analog addressable loops can be wired with ordinary, parallel fire alarm rated wire. The “addressable”
feature allows for each sensor, initiating device, and control m odule to be individually described on the system LCDs. The panel itself is easy to program, with self-explanatory menus and LED condition indicators.
In addition, Zeta offers an additional upgrade to the system, allowing the end user to program the panel
directly from their PC.
This manual is a complete Installation and Operation guide that includes the following six sections:
Section 1—System Overview: Describes the panel features, agency listings and approvals, technical specifications, wire specifications, and system architecture and overview.
Section 2—Installation Procedures: De scribes the hard w are and sof tware, sequence overview,
and instructions on how to install the Classic 2000 Mk II control panel.
Section 3 S y stem Controls and Oper ation: Provides the panel operation instructions, including
a basic layout and description of the visual indicators and function keys.
Section 4-- System Programming: The “how to” section to program your specific devices and
system, including a description of the menus found on the panel.
Section 5—Special Application Programming and Operation: “What can this system do for
you?” is provided with detailed programming and operation of common applications.
Section 6—Networking/Serial Devices: Description of how to install and work with network
devices.
Section 7-- Appendices: O th er informati on relevant to the Classic 2000 Mk II and this manual,
including a glossary of terms.
If you have any questions or concerns about the installation, operation, or programming of the Classic
2000 Mk II Analog A ddres sable FACP, please refer to our web site
http://www.zeta-alarms.co.uk
or E-mail support at nrpj@zeta-alarms.fsworld.co.uk
If you prefer, contact us at:
Technical Services Department
Zeta Alarm Systems
72-78 Morfa Ro ad
Swansea SA1 2EN
U.K.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 3
1.2 System Overview
The Classic 2000 Mk II is a sophisticated microprocessor-ba se d analog addressable fire alarm control
system suited to the various needs of commercial, industrial and institutional applications. The MkII provides the ability to “software” configure and label 1512 SLC points plus system and network points. It functions in accordance wit h the National Fire Protection Association (NFPA) Standard 72 Fire Alarm
Code as a manual, automatic, and waterflow control system for local, central station, and remote station
applications. Activation of a compatible sensor or normally open fir e ala rm i nitiating devices will sound
audible appliances, notify a remote station, annunciate a fire or ala rm condition, and energize supplementary relays.
1.2.1 List of Standard Features
AC Power
110 VAC or 220 VAC 50/60Hz
Smart, Universal Power Supply
DC Power
Standard 6 Amps total (5.75 Amps available for all outputs combined)
Intelligent multi-rate battery charger
All outputs are filtered
Panel Annunciation
80-character backlit LCD
LEDs for System Alarm, System Trouble, Supervisory, AC Power , Offline, Test Mode
LED indication of silence d Alarm, Trouble, or Supervisory condition
16-button keypad for all programmi ng and control functions
Real-time clock/calendar display
Point description, location, and c ondition is displayed when appropriate
Battery-backed 650+ event history log
Programming
Keypad programming on the front panel or the Remote Programming Display (RPD)
Three levels of Password protection
Auto-programming of SLC, System Devices and Network Devices
Initiating Circuits
2 Signal Line Circuits (SLC) standard, digital communication protocol, can use standard fire
rated cabling
Wire run length of up to 9,900 ft. with 14 AWG wire
126 addressable devices per SLC
SLC can be configured as Style 4, 6, or 7 without a reduction in the number of
circuits available
All SLCs are fully supervised and prot ected from surges
Notification Appliance/Auxiliary Power Circuits
4 programmable outputs c a n be e ith er n ot if ic at ion appliance (NAC) or auxiliary power circuits
All circuits can be configured as Style Y (Class B) or Z (Class A) without a reduction in the
number of circuits available
2.75 Amps p er c ircuit available subject to the combined total limit of 5.75 Amps
NACs signal pattern programmable for March Time, ANSI Temporal Code, or Continuous
All circuits are fully supervised and protected from surges
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 4
Relay Outputs
Form C relay outputs for System Alarm and Trouble
Up to 20 programmable auxil iary system relays optional from the main board
Cabinet
16-gauge cold rolled steel finishe d in red powder coat enamel with space at bottom
for batteries
Conduit knockouts in the top, sides, and back
Removable Door with key lock
Will house a 2 or 4 SLC system
Analog Addressable Sensors
Photoelectric and ionization sensor heads have sensitivity se t i n the software database
Heat sensor is programmable to alarm at 135° F to 190° F
Sensor address is set via DIP switches
Addressable Modules
Modules fit a single gang box or 4" square boxes and have an LED visible through cover
A sounder control module provides a NAC
An input-output module has a supervised input and a relay output that follows its input and
may be configured as input point or output point
The isolator module, while not addressable, includes a mounting base and does not require an
electrical box for mounting
Addresses are set via DIP switches
Module inputs can be wired as Class A or B, which is switch selectable at t he module
1.2.2 List of Optional Features
DC Power
A heavy duty 7.5 amp power supply
ZIPB-3 power supply/ booster provides 3 amp distributed power
Auxiliary System Relay Outputs
Up to 4 ZZRM Form C relay modules may be added (20 programmable system relay contacts)
Communication Port Options
Zeta Isolated communication port (ZICP) and non-isolated communication port (ZSCP3)
1.2.3 List of Network Features
All devices below communicate with the panel through an RS-485 data bus.
SLC Expansion
ZACM-A modules with 2 loops of 126 points can be added to the base system to reach 1512
point capacity
Up to 600 Conventional Initiating Zones can be added by using Dual Input / Output Modules
(ZDIO), Panel Network Interface for the Sigma Mk I I panel (ZPN1-1K), or five (ZFZA) or ten
(ZTZB) zone modules on the RS-485 data bus
Remote Annunciation
Remote Display Annunciator provides a remote 80-character display to mimic the panel display
ZRLD Modules will drive u p to 60 LEDs for graphic annunci ators
All annunciators communicate with the panel through an RS-485 data bus
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 5
City Tie/Reverse Polarity Module
City Box/Reverse Polarity Module (ZCBM) with a disable switch allows for conn e ction to monitoring facilities
Networked Digital Communicator
Zeta Networked Digital Communicator (ZNDC) is a UL listed, dual-line dialer that allows a
Sigma Mk II or Class ic 2000 Mk II FACP to report events to a central monitoring station, over
the public phone system.
ZNDC requires the use of 2 phone lines.
Conventional Z one Expansi on
Five Zone Expansion module (Z FZA) provides five Class A initiating loops.
Ten Zone Expansion module (ZTZB) provides ten Class B initiating l oops.
Panel Network Interface (ZPNI) — see following section.
Zone Relay Module provides five expansion relays. Note: this device does NOT attach to the
RS-485 network, but instead has it’s own port on the board.
Panel Netw ork Interface
ZPNI-S1K provides a way for the Classic 2000 Mk II panel to communicate with a Sigma Mk II
FACP, using Sigma Mk II inputs as addressable points.
Dual Input-Output Module
The ZDIO module contains two class B inputs an d two class B / relay outputs.
The two inputs provide two-wire initiating circuit for normally-open fire alarm and
supervisory devices.
The ZDIO’s outputs may be configured inone of two ways. It may be made to switch external
DC power or audio power (up to 100Vrms) to notificaiton appliances. It may also be configured
to provide one set of Form-C (SPDT) relay contacts per output.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 6
1.3
Agency Approvals and Listings
The Classic 2000 Mk II Control System is designed to comply with Underwriter Laboratories (UL) Stan dard 864, Control Units for Fire-Protective Signaling Systems.
The Classic 2000 Mk II are Underwriters Laboratories listed for the applications described below:
Type * Type Service ** Type Signaling Models
Local A, M, WF, SS M, NC or C 3002-3008
Central Station A, M, WF, SS DACT 3002-3008
Remote Station A, M, WF, SS DACT, REV. POL. 3002-3008
*Automatic (A), Manual (M), Water Flow (WF), Sprinkler Supervisory (SS)
**March Time (M), Cod ed (C), Non Coded (NC), Digital Alarm Communicator (DACT)- separately listed
Anyone installing this system should have familiarity w ith:
Installation Manual Part # 3000-6000
NFP A 72
NEC Article 300 Wirin g Methods
NEC 760 Fire Protective Sig naling Sys tems
EIA-485 and EIA-232 Serial Interface Standards
Applicable Local and State Building Codes
Requirements of Local Authority Having Jurisdiction
Underwriters Laboratorie s has the following Pre-connection Requirements:
A All AC wiring connected to the Classic 2000 Mk II enclosure is to be installed in conduit
B All field wiring must be installed in accordance with the National Ele ctric Code (NFPA 70)
C All field wiring must be 18 AWG or larger (system accommodates 14-24 AW G )
D High and Low voltage wiring should be segregated and routed as described in Section 1.4.8.1
E Use only the compatible sensors and modules listed in Appendix C-2 on the SLC loops
F The Control m ounting location should allow easy access and proximity to all audible alerts
and local annunciation by the person(s) having responsibility fo r maintaining and supervising
the system
G All 2-wire smoke detectors utilized on ZTZB/ZFZA must be listed as compatibl e in Appendix C
H Supervised audible and visual appliances as listed in Appendix C Compatible Devices should
be located so as to conform to UL and the ADA where required
I A full system checkout must be performed any time the panel is programmed
J The system should be maintained in accordance with NFPA 72 standards
Specific instr uctions on confi guring and programmin g to achie ve some common
application s are co ntained in Section 5, and may have additional requirements.
Please remember that all installations are regulated by the Local or State
Authority Having Jurisdiction (AHJ) as they interpret the applicable
NEC, NFPA and UL standards and regulations.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 7
1.3.1 Specific UL Requirements
1.3.1.1 Local Protected Fire Alarm Systems
At lease one UL listed, supervised notification appliance must be used.
1.3.1.2 NFPA 72 Central Station – Zeta Networked Digital Communicator (ZNDC)
NFPA 72 requires a central station monitored system to include battery backup to power the system for 24 hours with 5 minutes in alarm at the end of that period. It requires t hat reporting loss of
AC power trouble condition be delayed until 25% of battery backup capacity has been utilized.
Requires use of UL listed dual-line dialer as programmed in Section 5 and connected in
Appendix F.
See the Instructions in cluded with t he ZNDC for wiring, programming, and setup
Requires that AC Loss reporting be set to delay from 6 to 12* hours
1.3.1.3 NFPA 72 Remot e S ta t ion – Zet a Net wor ked D ig ita l Comm unic at or (ZND C)
NFPA 72 requires a remote station monitored system to include battery backup to po wer the system for 60 hours with 5 minutes in alarm at the end of that period. It requires t hat reporting loss of
AC power trouble condition be delayed until 25% of battery backup capacity has been utilized.
Requires use of UL listed dual-line dialer as programmed in Section 5 and connected in
Appendix F.
See the Instructions in cluded with t he ZNDC for wiring, programming, and setup
Requires that AC Loss reporting be set to delay 15 to 24 hours*
*the Classic 2000 Mk II allows settings of 0, 8, or 16 hours
IMPORTANT!
The following applications require both programming and special wiring instruction.
PLEASE REFER TO SECTION 4 FOR INSTRUCTIONS ON PROGRAMMING AND REVIEW
ALL PROGRAMMING SELECTIONS TO INSURE THAT THE MODIFICATIONS CORRESPOND
TO YOUR REQUIREMENTS.
THE FOLLOWING SECTION LISTS REQUIREMENTS FOR EACH SPECIFIC TYPE OF
INSTALLA TIO N. WHEN INST ALLING AN INDIVIDU AL DEVICE, REFER TO THE SPECIFIC SECTION
OF THE MANUAL REFERENCED FOR ADDITIONAL INSTRUC TI ONS.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 8
1.4 Technical Specifications
1.4.1
Power Supply
24VDC Power Available
Nominal AC Input Voltages Primary Current
5.75 -Amp Supply 120 VAC/60 Hz or 220 VAC/50 Hz 120V/2.5A; 240V/1.5A
7.5 -Amp Supply 120 VAC/60 Hz or 220 VAC/50 Hz 120V/3A, 240V/1.5A
1.4.2 Battery Charger
Multi Rate Smart Charger
Battery Charge Current 1.5 A maximum
Battery Charge Voltage nominal 27.6 VDC
1.4.3 Notification Appliance Circuits/24VDC Auxiliary Outputs
Each circuit is programmable for reverse-polarity notification circuit or 24VDC auxiliary power.
Notification Appliance Circuit Specifications
Outputs 1-4
Nominal Output Voltage 24 VDC
Maximum Output Current 2.75 Amps
Supervision Current 0.5 mA
End-of-line Resistor 10K Ohm
Wiring Style Compatibility Style Z, Style Y
Each circuit is supervised, power limited by an electronic circuit breaker and employs transient
voltage protection
Each Output is individually programmable by Output Group for Continuous, March Time, or
Temporal Coding output
24VDC Auxiliary Output Specifications
Outputs 1-4
Nominal Output Voltage 24.0 VDC
Maximum Output Current (Each) 2.75 Amps
Non-supervised 24 VDC provided at term inal block. Power limited b y an e lectronic circuit
breaker.
Each output is individually programmable for resettable or continuous output.
1.4.4 SLC Specifications
Maximum Resistance 50 ohms
Maximum Loop C urre nt 200 mA
Wiring Styles Styles 4, 6 or 7
1.4.5 System and Auxiliary Relay Outputs
All auxiliary and system relay outputs (Alarm , Trouble, and ZZRM) carry the sa me ratings.
Technical Specifications
Contact Type Form C (SPDT)
Contact Rating 5A @ 28 VDC/30 VAC Resistive
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 9
1.4.6 RS-485 Network
Maximum numb er of devices - 127
EIA-485 Circuit rating - 5.5VDC max., 250mA(short circuit)
Data Transfer Rate – 19,200 Baud
Recommended Wire Type – 14-22 AWG twisted - pair (See Sec. 1.4.8.3)
Maximum Cable Length - 8000 ft. (@16AWG)
Maximum Total Cable Resistance – 50 Ohms
Maximum Cable Capacitanc e – 0.3µF
NOTE: Refer to Section 6.5 for serial device specifications.
1.4.7 Communication/Printer Ports - ZSCP3/ZICP
RS-232 Port Specifications
Data Rate - 9600 bps
Data Bits - 8 data bits
Stop Bits – 1 stop bits
Parity - None
Data Flow Control - XON/XOFF
Connector Type - DB9 Male
Connector Pinout*
Pin #
Pin Name Pin Function Input/Output
1 DCD Data Carrier Detect Not Connected
2 RX Receive Data Input
3 TX Transmit Data Output
4 DTR Data Terminal Ready Output
5 GND Signal Ground Bi-directional
6 DSR Data Set Ready Not Connected
7 RTS Request To Send Output
8 CTS Clear To Send Input
9 RI Ring Indicator Not Connected
NOTE: Pin 4 (DTR) is connected t o Pi n 6 (DSR) on the ZSCP3 and ZICP printed circuit boards.
*Type of Cable - The abov e printout applies only to the ZSCP3. Pins 2 and 3 are opposite on the ZICP.
Thus, the ZSCP3 requires a Null Modem cable; the ZICP requires a Straight-Through cable. Both cables
must be DB9, Female-to-Female.
Maximum C able L ength - Determined by dat a rate and cable capacitance (typically max 50 ft)
Maximum Cable Capacitance - 2500 pF at a data rate of 9600 bps
Less cable capacitance will allow longer cable runs.
Any ITE listed equipment device connected to the ZSCP3 RS232 port must have an isolated ground
Any ITE listed equipment connected to the ZSCP3 with a ground referenced to earth ground will
cause a ground fault trouble in the Classic 2000 Mk II Control Panel.
USE THE ZE TA ISOLATED COMMU NIC ATION POR T ( Z ICP) for connec t ion to ITE Equipment without
isolated ground.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 10
1.4.8 Wiring Specifications and Requirements
All circuits except AC, System Relays, and batter y cables are power limited.
1.4.8.1 General Specifications
The Classic 2000 Mk II should be wired to NEC 760 standards. Induced n oise (t ransfer of electrical energy from one wire to another) can interfere with panel communications or cause fals e
alarms or device troubles. To avoid induced noise, observe the following guidelines:
Maintain at least ¼” spacing between power limited and non-po wer l im it ed circuits
Wiring should not cross or rest on the circuit board
Segregate high current output and AC power wiring from SLC and input wiring
Segregate wiring from ZACMs (do not run wire for multiple ZACMs in the s ame conduit)
Prior to terminating wire at the panel, please verify continuity, and that capacitance and resistance comply with standards set out in section 1.4.8.2.
See the following two sections f or t he recommended wire for each type of circuit.
Do not use a single multi-conductor cabl e for the entire panel. Separate wiring as follows:
High Voltage P S C Terminal TB-1 – L, N, G
Notification Appliance Circuits (NAC) Terminals 1-16
Signal Line Circuits (SLC) Terminals A-, A+, B-, B+ on SLC1 through SLC12
Network Terminals 17-26
Relay Circuits Terminals 27-32
Do not pull wires from different groups through the same conduit. If you must run them together,
keep the distance as short as possible, and use shielded cable. Route high and low voltages separately, and do not cross the ci rcuit board with wiring inside the panel enclosure.
Running the wire through ferrite shield beads or wrapping it around a ferrite toroid can also filter
high frequency noise.
1.4.8.2 SLC Wire Specifications
Any wire type may be acceptable (solid, stranded, twisted pair, untwisted, shieldd, unshielded) as
long as it complies with the following specifications:
14 - 20 gauge
Limit of 0.3µF capacitance over entire line (refer to Application Note AN-Z3K-01A for figuring
line capacitance)
Limit of 50 Ohms resistance over entire lo op (from panel to fart he s t point and back)
Complies with NEC standard 760-51 for power limited, fire protective signaling cable
In retro-fit applications, please note:
-Never
run wiring from two different ZACMs in the same conduit.
- Wiring utilized from original installation must conform to NEC installation standards as well
Maximum loop length depends on wire gauge a s shown below:
Wire Gauge (solid)
Solid Distance Stranded Distance
20 2,400 ft. 2,300 ft
18 3,900 ft. 3,600 ft.
16 6,000 ft. 5,300 ft.
14 9,200 ft. 9,000 ft.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 11
To determine your loop length measure from the farthest device on the loop back to the Classic
2000 Mk II or Remote Addressable Commun ication Module. When measuring a “T” tap, go from
the farthest device on the “T” tap section back to the main SLC loop and from that junction back to
the panel.
1.4.8.3 Network Wiring
Network communication wiring requires a shielded, twisted pair of wires between each device. In
addition, all network devices require battery backed 24VDC power. Twisted, shielded pair may be
required for some installations. Following are examples of acceptable net wire.
Network Communication 14-18 AWG min
Twisted Pair– 14 AWG Belden 9580
16 AWG Belden 9572
18 AWG Belden 9571
Tw isted, Shielded Pair 14 AWG Belden 9581
16 AWG Belden 9575
18 AWG Belden 9574
Network Power 18 AWG
1.4.9 Calculating Maximum Current Draw and Battery Backup Requirements
This section will assist you in determining the ma ximum system current draw and standby battery
needs for your in stallation. Follow the steps below to determine the current draw and standby b attery requirem ents. Appendix B-- Classic 2000 Mk II Current Draw/Battery Backup lists the alarm
current draw for the panel, ZACM Loop Cards, and serial device expansion modules.
Alarm Current is determined by multiplying the quantity of items by its alarm current draw. To
quickl y determine maxim um system current draw, perform the following c ompu tations:
1. Enter Quantity of ZACMs in the system.
2. Fil l in th e quan t iti e s of add re ssa b le devices and mult iply by their al arm current require ments.
Record the total in the Maximum Alarm Current columns. Fill in the quantity of SLCs in the
system (number of ZACMs times 2). Multiply the number of loops by the maximum alarm current per loop, then sum the columns.
3. Fill in the quantities and current draw of t h e Notification Appliances or auxiliary-powered
devices for each output from the manual for each specific device, and compute the total current required. Record in the NAC Alarm Current column Line D.
4. To tal the current required for Alarm conditions in Amps and multiply by 1.2 for safety factor.
5. Make su re the total alarm current you calculated (including current for the panel itself) does
not exceed 5.75 Amps (7.5 Amps part # Z3000-6008). This is the maximum alarm current
allowable. The ZIPB-3 or other independent, listed, regulated 2 4VDC supply with battery b a c kup that is listed for fire alarm system use may be used to add additional powe r to the system.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 12
1.5
Before You Begin Installing…
Prior to installing the Classic 2000 Mk II analog addressable control system, please review this
operations manual in its entirety.
Attending a formal training class is re quired prior to purchase a nd installation of the Classic 2000
Mk II.
In addition, Zeta Alarm Systems recommend that you perform the following research prior to installation:
Determine the NFPA, NEC, ADA, and any local or AHJ requi rem ents that apply to your installation
Determine the total num ber of devices and notifi cation appliances
Determine maximum system current draw and standby battery requirements of the system
(refer to Se ction 1.4.9 and the appendix)
Determine the wire specifications required (refer to section 1.4.8)
Determine the maximum length of wire runs for the NACs, network and conve ntional zones
Determine the n otification requirements
Determine a suitable location for mounting the control system
Determine the labeling and grouping requirem e n ts for the system input points
1.5.1 System Architecture and Overview
The Classic 2000 Mk II has up to 1,665 programmable inputs and outputs as outlined below.
NACs 4
System Relays 2
City Box Module 2
Hot Keys 5
Auxiliary System Relays 20
Total System Level “points” 33
SLC Points (126 addresses on 12 SLCs) 1,512
Conventional Zone “points” 120
Total Programmable Input & Output Points 1,665
Programmable system outputs include 4 notification appliance circuits (NAC), 2 system relays, 2
Zeta City Box Modules (ZCBM), and up to 4 ZZRMs each with 5 individually programmable relays
for a total of 20 auxiliary system relays.
The system accommodates a total of 4 Zeta Addres s able Communication Modules (ZACM). Each
ZACM contains 2 SLC loops each. ZACM 1 is included on the CP3. A second ZACM may be
added to the CP3 to expand the base panel to 4 loops (504 points). E xpansion of the panel to 12
loops (1,512 total points) is explained in 1.5.1.1.
1.5.1.1 Adding Remote ZACMs
Additional ZACM modules may be used to expand the system to up to 12 loops by adding a Zeta
Serial Device Enclosure (ZSDE) to house the ZRPC and up to 2 ZACM modules
1
. The Zeta
Remote Po wer Converter (ZRPC) provides connections for the network and 24VDC, and serves as
a mounting platform for up to two ZACMs.
1. Note: The last two ZACM’s must be special-ordered. See Appendix A for pa rt numbers.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 13
1.5.2 Point Programming Overview
The Classic 2000 Mk II allows for programming of all system inputs and outputs. For specific programming instructions, refer to Section 4.
NOTE: Every time you make a change in programming to add or delete SLC or Network devices,
you must rescan the loops (Auto-Program Mode).
1.5.2.1 SLC Devices, Bases, and Accessories
There are sixteen types of SLC devices available for the Classic 2000 Mk II system. These
devices include sensors and three varieties of bases, mini and standard priority switch monitor
modules, a sounder control module, a combination input/output module, and a short circuit isolator
module as shown below.
1.5.2.2 Global Input Programming Options
Auto-Test Time
Define Photo Sensor Analog Sensitivity settings for Low, Medium and High
Define Ion Sensor Analog Sensitivity settings for Low, Medium and High
Define Temperature Sensor set points for High, Medium and Low temperatures
Establish Maintenance & Service Ale rts for photo, i on and temperature sensors
Part Number Description
55000-550 Ion Sensor Head
55000-650 Photo Sensor Head
55000-450 Temperature Sensor Head
55000-750 Isolator Module
45681-211 Isolator Base
45681-234 Low-Profile Base, 6”
MB-RLY-XP95A Base with Relay, 4-wire
MB-SDR-XP95A Base with Sounder, 4-wire
45681-771 Xpert Address Programming Card
55000-830 Mini Priority Monitor Module
55000-806 Priority Monitor Mod ule
55000-825 Sounder Control Module
55000-820 Monitor Input/Output Module
RW -AA-N Duct Housing w/ Ionization Sensor Head, Exhaust Tube
RW-AA-P Duc t Housing w/ Photoelectr ic Sens or Head, E xhaust Tube
RW-AR-N Duct Housing w/ Ionization Head, Exhaust Tube, Form C Relay
RW -A R-P Duct Housing w/ Photoelectric Head, Exhaust Tube, Form C Relay
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 14
1.5.2.3 System Timing Options
Establish 4 Day/Night sensitivity schedules
Establish up to 18 Holidays
Establish up to 4 System timing schedules
Auto-Silence
Silence Inhibit
Alarm Verification
1.5.2.4 Input Point Programming
Each sensor allows programming of the following parameters:
40-character label
Alarm verification enable/disable
High, medium or low sensitivity selection
Temperature set point in the temperature sensor (H, M, L between 130 and 195 degrees)
Output group assig nme nt
Selection of Day/Night sensitivity schedule (Photo, Ion and Heat Sensors)
Each switch monitor module or input point on the conventional zones may be programmed with a
40-character label, and for one of 10 different functions:
Alarm input
Manual pull station
Waterflo w Ala rm
Supervisory Alarm Input
Drill Test Input
Remote Silence
Remote Reset Input
Control Input
Control NL (Non-Latching)
Supervisory NL (Non-Latching)
Photo sensors may be programmed as Duct “T” (Trouble) or Duct “S” (Supervis ory)
1.5.2.5 SLC Output Point Programming
Each output point allows programming of the following parameters:
Select for the “All-call” group,
Define silence operation
Select for one of 4 output schedules
Associate with up to 5 outpu t groups
Provided a 40-character courtesy label
1.5.2.6 Output Groups
The panel accommodates up to 199 output groups. Each output group provides the following
options:
Enable/disable
Floor number selection
20-character courtesy label (the courtesy label is for reference only, and is only visible when
viewing group status, or on printed programming reports, NOT when the group is activated
Alarm count
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 15
Output Group Su m m a ry
1-90 = General
91 = Non-Reporting
92 = Schedule Group #1
93 = Schedule Group #2
94 = Schedule Group #3
95 = Schedule Group #5
96 = Waterflow operation (all alarm inputs, alarm relay and all out puts defa ult here)
97 = Supervisory operation (auxiliary relay default)
98 = Trouble (trouble relay default)
99 = Alarm (all alarm inputs, alarm relay and all outputs default here)
100-199 = General
1.5.3 City Box and Reversing Polarity Interface
The Zeta City Box Module (ZCBM) is capable of interfacing with reversing polarity and supervised
coil type master boxes. The ZCBM mounts below the CP 3 and via the RS-485 serial bus on the
CP3. It features a manual disconnect switch for convenient testing and maintenance.
1.5.4 System Auxiliary Relays
The CP3 allows for the connection of up to 4 ZZRM relay modules. Each ZZRM contains 5 Form-C
relays that are individually programmable. Each ZZRM co mes w ith snap-track for mounting and a
cable to connect to the expansion port of the CP3.
1.5.5 System Control Hot Keys
Keys 6-0 allow the user to utilize the keys as programmable function keys or control points. By utilizing the point programming screens, the user can associate output groups to be controlled by the
press of the Hot Key.
Hot Keys are located on loop “0.”
Addresses range from 30-34 (0:30-0:34).
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 17
2. Installation Procedures
The following procedures, diagrams, and instructions should be followed closely to avoid damage to the
control panel and its associat ed equipment. S ystem reliability depends primarily upon proper installation,
testing, and maintenance procedures. (Refe r to Appendix A for Part Numbers and Ordering Information.)
DO NOT deviate from the following instructions.
2.1 WhatDoIHave...
The control unit is shipped in five basic sections:
The Enclosure
The CP3/LPD assembly
The Pow er Supply Chassis assembly
Assembly Hardware Kit (cables, hardware, EOLs)
Any additional modules (ZCBM, Z SCP3, ZZRM, ZFZA, ZTZB, ZNDC, ZDIO, ZPNI-S1K, etc.)
2.2 Installation Sequence
Installation p roce dures should be performed in the sequence outlined below. This will
make the most efficient use of time, and minimize the likelihood of accidental damag e to
the equipment. Please refer to Figures I-1 and I-4 to properly identify the components listed
below.
Step
Number
Description of Task
Completed
1
Mount Enclosure
2
Install CP3 Board
3
Mount Chassis into Enclosure
4
Install ZZRM Auxiliary System Relays (opt.)
5
Install Optional modules as required
6
Connect AC P ower
7
Connect Batteries
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 18
Exploded Assembly Figure I-1
NOTES:
1. Space shown for optional ZZRMs above ba ttery storage space may be used to install
the follow ing modules: ZTZB, ZFZA, ZRPC/ZACM combin atio ns, ZCBM, or the ZNDC.
2. To install optional modules, utilize the Snap-Trac k and installation instructions included
with each module. To install Snap-Track, remove protective covering from self-adhesive
strips on the back of each Snap-Track. Position Snap-Track squarely under the Power
Chassis, and press fir m ly onto the ba ck of the cabinet. Be sure to leave adequate spacing for a wiring channel and the backup batteries
3. If the battery storage space is not utilized, the batteries must be installed in a separately
Listed fire protective signaling enclosure.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 19
2.2.1 Mount Enclosure
Install the Enclosure as follows:
1. Carefully unpack the system components and inspect for any damage due to shipping .
2. Mount the enclosure in a clean, dry, vibration-free area where extreme temperatures are not
encountered. The location should be readily accessible with sufficient room for easy installation and maintenance.
3. Locate the top of the cabinet 6 feet a bove the floor, with the hinge mounting on the left.
4. Mount cent ering the single hole in the upper back of the cabinet to the center of a wall stud.
After the panel has been properly located using the center-mounting hole, the panel can be
secured using the bottom mounting holes located in each corner. Use screws or bolts no
smaller than No. 10 or 3/16 inches in diameter for cabinet mounting. Always make c ertain the
panel is securely anchored.
5. Complete all conduit connections to the cabinet. Use the knockouts provided in the top, sides,
or back of the cabinet. Wire should NOT enter the bottom of the cabinet, since this area is
intended for batteries.
NOTE: All wiring should be in accordance with Article 760 of the National Electrical Code NFPA 70
and state and local codes for fire alarm systems. All co nductors should be tagged or otherwise
coded and logged at installation to identify circuit assignment, polarity, and Class “A” circuits,
whether outgoing or incoming.
2.2.2 Install CP3 Board
NOTE: All expansion boards should be attached to
the CP3 prior to mounting the CP3 to the Power Chassis and assembling in the cabinet. Never attach any
accessory boards to the CP3 without first removing all
power (AC and batteries). Doing so will VOID
the war-
ranty.
(Refer to Figure I-1 to pro perly identify components.)
After enclosure has been securely attached in the
proper mounting location, attach the CP3 module to
the Power Chassis. This is accomplished by aligning
the seven plated holes on the board with the mounting
studs on the Power Chassis and making sure that the
power connection plug of the CP3 is directly above the
Power Chassis socket. Press down firmly until the
board “snaps” into place.
2.2.3 Mount Chassis in Enclosure
After the enclosure has been securely mounted in a
suitable mounting location, set the mounting studs at
the bottom of the power chassis into the mounting
hinge brackets inside the cabinet. The Power Chassis
will set securely in the brackets, extending like a shelf
to allow connection of AC power. (Refer to Figure I-2
for mounting illustration.)
Figure I-2
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 20
2.2.4 Connect AC Power
Refer to Figure I-3 for wiring diagram.
1. Attach the black (hot) wire from
the source to terminal “Line” on
the Power Supply Controller
(PSC) board.
2. Attach the white (neutral) wire
from the source to the “Neutral” terminal on the PSC
board.
3. Attach the ground wire from
the source to the “Eart h” t erminal on the PSC board.
2.2.5 Connect Batteries
Power up the system prior to connecting the batteries and prior to
making any input or NAC connections. This will insure that th e system is operating properly prior to
field wiring and assist in trouble
shooting should any problems
arise after field wiring is terminated.
Connect batteries to the system as follows (See Figure I-3):
1. Connect the sho rt black wire (from the assembly hardware kit) from the negative terminal on
Battery 1 to the positive terminal on Battery 2.
2. Connect the red wire from the battery wire harness to the positive terminal on Battery 1.
3. Connect the black wire from the batte ry wire harness to the negative terminal on Battery 2.
WARNING!
To reduce the risk of electrical shock, make sure that a ll power has been turned off or discon-
nected prior to attempting to connect power to the Power Supply Controller.
Apply AC Power BEFORE connecting batteries to the CP3.
Provide the Fire Alarm Control Panel with a dedicated AC Circuit rated 15 Amps
Figure I-3
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 21
2.2.6 Install Optional ZZRM Auxiliary System Relays
Up to four Zeta Zone Relay Modules (ZZRMs) can be connected to allow up to 20 sets of programmable auxiliary relay contacts. Snap-Track (included w/ZZRMs) can be installed for mounting the
Optional Relay boards in the bottom of the cabinet above the battery space.
2.2.7 Install Optional Modules
The Classic 2000 Mk II CP3 offers several optional modules that connect via the RS-485 Network.
Modules may be accomodated under the CP3 module and above the battery storage area.
Optional modules t hat do not fit in the space below may be installed in an optional Zeta Serial
Device Enclosure (ZSDE). Please consult the module installation instructions for more details.
2.2.8 Power Limited Wire Routing
Figure I-4
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 22
2.3 Wiring the Signaling Line Circuits (SLCs)
Communication with the addressable initiating, monitor, and control devices occurs through Signaling Line Circuit (SLC) loops. The basic unit includes two SLC loops on the main circuit board;
two SLCs are included on each Zeta Addressable Communication Module (ZACM). Each SLC
loop can be wired to meet the requirements of the NFPA Style 4 (see Figure W-2), Style 6 (Figure
W-3), or Style 7 (Figure W-4). Refer to Section 1.4.8 for wiring specifications.
There are four basic types of devices that can reside on an SLC:
1. Isolator Modules (IMB-750) permit a group of sensors and modules to be electrically “iso-
lated” from the remainder of the SLC, allowing critical loop dev ice s to function in the event of a
circuit fault (see Figure W1d). IMB -750s are required to meet NFPA Style 7 requirements.
2. Switch Mo nit or M odule s (MPM-830, PMM-806) and Input/Output Modules (MIO-820) allow
the control panel to monitor entire circuits of conventional alarm initiating devices such as
manual pull stations, smoke detectors, heat detectors, waterflow and supervisory devices (see
Figure W-6). Monitor modules can also have specialty functions. Refer to Section 5 For more
information on the specialty functions
3. Smoke and Heat Sensors (ISH-550, P SH -650, TSH-450, RWAA[X], RWAR[X]) allow the
panel to monitor an environment for smoke and heat conditions indicating a fire condition.
(See Figures W-1a-e for base wiring)
4. Output and Input/Output Modul es (S CM-825, MIO-820) allow the control panel to selectively
activate notification and relay outputs. (See Figures W-7, W-8)
2.3.1 SLC Device Capacity
Each loop will support up to 126 addresses for devices of any type. Isolator modules do not require
an address and are not included in the 126-device total. The basic panel will accommodate 252
total devices. The panel will support three additional Addressable Communication Modules
(ZACM) and each ZACM will support 252 total devices up to a total of 1,512 total addressable SLC
devices.
2.4 Sensor Base Wiring
There are three types of bases that may be used with the
optical, ionization, and thermal sensors: XP95A Mounting
Base (Figure W-1a), MB-SDR-XP95 Sounder Base (F igure W-1c), and the MB-RLY-XP95 R elay Base (Figure W1b). The isolator base, (wiring shown in Figure W-1d), is
only used with the isolator module.
Figure W-1e displays base wiring for two duct detectors —
RWAA, R WAR.
Figure W-1a
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 23
Note:
Power Supply connected to the base should be from the Classic 2000 Mk II, ZIPB-3, or independent, 24VDC supply listed for fire protection, with battery backup and power limited as per NFPA
72.
Figure W-1b
Figure W-1c
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 24
NOTE:
L1 and L2 are polarity sensitive on the ISOLATOR MODULE #IMB750, but not the other bases.
Figure W-1d
Figure W-1e
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 25
2.5 Installing SLC Devices
Communications Lo op Performa nce Chart
Fault Condition
Style 4 (two-wire) Loop Op eration
(meets NFPA 72 Style 4 requirements)
Style 6 (four-wire) Loop Operation
(meets NFPA 72 Style 6 requirements)
(3) Style 7 (four-wire) Loop Operation
(meets NFPA 72 Style 7 requirements)
Notes:
1. Trouble indicates a trouble signal will be generated at the control unit display during the abnor-
mal condition.
2. Alarm Capability indicates an alarm signal can be transmitted to the control unit d uring the
abnormal condition.
3. Loop operation meeting Style 7 requirements isolates entire physical zones on the communi-
cations loop from faults that occur within other areas of the loop.
4. Refer to the installation drawings supplied with each SLC device for rating and specification
information.
Single Open
on Loop
Single Ground
on the Loop
Shorted Loop Loop Shorted
and Opened
Loop Shorted
and Grounded
Loop Opened
and Grounded
(1) Trouble (2) Alarm
Capability,
Trouble
Trouble Trouble Trouble Trouble
Alarm
Capability,
Trouble
Alarm
Capability,
Trouble
Trouble Trouble Trouble Alarm
Capability,
Trouble
Alarm
Capability,
Trouble
Alarm
Capability,
Trouble
Alarm
Capability,
Trouble
Trouble Alarm
Capability,
Trouble
Alarm
Capability,
Trouble
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 26
2.5.1 NFPA Wiring Styles
Refer to the diagram below for interconnection of the Panel to the Loop bases and isolator modules.
Figure W-2
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 27
Figure W-3
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 28
Figure W-4
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 29
2.5.2 Input Modules
Single Switch Monitor Module
Figure W-6
Notes for Class A and Class B Wiring
1. All wiring must conform to applicable local codes, ordinances and regulations e.g. NFPA 72.
2. The module will be supplied with the yellow and green pigtails sleeved to avoid short circuits,
and ready for operation in Class B mode. T o operated in Class A mode, remove sleeving from
pigtails an d make appropriate connections as required.
3. Select Class A or B mode using BIT 8 of DIL switch.
4. Refer to Device instructions or Appendix J for addressing instructions
5. Symbols represent normally open devices (compatible conventional detectors, pull stations,
or switches).
6. All input circuits are supervised and power limited.
7. Use Listed 47-K, 0.5-W EOL resistor (PN 902A) for Class B.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 30
2.5.3 XP95A Switch Monitor Module/ XP95A Priority Switch Monitor Module
Figure W-6a
Notes for Input Module Class A and Class B Wiring
1. All wiring must conform to applicable local codes, ordinances and regulations. e.g. NFPA 72
2. Select Class A or B mode using BIT 8 of DIL switch
3. Refer to Appendix J or d evice installati on instruct ions for devic e addressing informa tion.
4. Symbols represent normally open devices (compatible conventional detectors, pull stations,
or switches).
5. All input circuits are supervised and power limited.
6. Use Listed 47-K, 0.5-W EOL resistor (PN 902A) for Class B.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 31
2.5.4 I/O Relay – I/O Input Module*
*Refer to Section 3.7.2 for configuration.
Figure W-7
Notes for I/O Module Class A and Class B Wiring
1. All wiring must conform to applicable local codes, ordinances and regulations. E.g. NFPA 72
2. Power supply connected t o t he module should be from the S3000, IPB-3, or independent, 24V
DC, listed for fire protection, with battery backup and power limited per NFPA 72.
3. Relay contacts shown in RESET condition.
4. Select Class A or B mode using BIT 8 of DIL switch
5. Relay rating, 2A @ 24 Vd c 0.35pf, 500mA @ 120Vac 0.35pf in fire protection applications.
6. See Appendix J or device installation instructions for addressing information.
7. Symbols represent normally-open devices (compatible conventional detectors, pull stations,
or switches).
8. All in put ci r c ui ts are su perv is ed and pow e r limi ted. The re l ay co ntacts are n on-supervised and
power limited.
9. Use Listed 47-K, 0.5-W EOL resistor (PN 902A).
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 32
2.5.5 Sounder Control Module
Figure W-8
Notes for Class A & Class B Wiring
1. Polarity shown when sounders are DE-ACTIVATED , supply is reversed when sounders are
ACTIVATED.
2. Power supply connected to the SCM should be fr om the Classic 2000 Mk II, ZIPB-3, or independent, 24V DC, listed for fire protection, with battery backup and power limited per NFPA 72.
3. To replace sounders with ‘P.A.’ speakers, move Jumper (J1) to disable the module external
supply monitoring.
4. When operated in ‘P.A.’ mode, an Audio Amplifier of 70.7 Vrms MAX should replace external
supply, with wire supervision capability as per NFPA.
5. All wiring must conform to applicable local codes, ordinances and regulations. e.g. NFPA 72
6. Use Listed 47-K, 0.5-W EOL resistor (PN 902A) for Class B.
7. Select Class A or B mode using Bit 8 of DIL switch
8. Relay Rating, 2A @ 24Vd c 0.35pf, 500mA @ 120Vac 0.35pf in fire protection applications.
9. Refer to Appendix J or the device’s installation instructions for addressing information.
10. All circuits are supervised and power limited.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 33
2.5.6 Sounder Base/Relay Base
Figure W-9a
Figure W-9b
NOTE: Power supply connected to bases should be from the IPB-3, or independent, regulated 24V DC,
listed for fire protection, with battery backup and power limited per NFPA 72.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 34
2.6 CP3 Wiring Termi nal Identification
Figure W-5
Remove protective cove ring
to utilize ZZRM port.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 35
2.6.1 Network Wiring
Note: For Class A, as shown in drawing, use terminals 17, 18, 23 and 24 for Network lines going out
from the panel. Use terminals 20, 21, 25 and 26 for Network lines returning to the panel. For Class
B, use only terminals 17, 18, 23 and 24.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 36
2.6.2 NAC Wiring
Figures W-10a, W-10b, and W-10c present Notification Appliance Circuit and auxiliary power connections.
Refer to Secti on 3 for program ming information and S ectio ns 1.4.3 and 1.4.8 for v olta ge drop information .
Figure W10-A Figure W10-B
A- B- B+ A + A- B- B+ A+
-+
-+
-+
-+
-+
-+
-+
-+
Listed EOL
#905A
NAC 1-4 STYLE
CLA SS A
NAC 1-4 STYLE
CLA SS B
Figure W10-C
A- B- B+ A+
24V DC AUXILIARY POWER OUTPUT
NAC 1-4
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 37
2.7 System and Auxiliary Relays
Figures W10-D present System Alarm and Relay connections on the CP3 assembly. Refer to Section 3 for
programming information and Sections 1.4.5 specification and rating information.
Figure W10-D
2.7.1 ZZRM Auxiliary Relays
To add auxiliar y re lay s to t he system (required for supervisory relay application), utilize the ZZRM (ZRM-5)
relay module to provide 5 individually programmable system relays (up to 4 ZZRMs may be added for a
total of 20 p r ogrammable system relays ). R efe r to Sect ion 4.2.5 for programming and Section 1.4.5 for
specifications.
Figure W10- F
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 38
2.7.1.1
Multiple ZZRM Relay Installation
ZZRM JP-1 Jumper Setup
Jumper pins 1and 2 on the ZZRM furthe st from the CP3 connection. All other ZZRMs should have
the jumper on pins 2 and 3.
ZZRM Installation (refer to section 2.9 for wiring schematic)
NOTE: Up to 2 ZZRMs may be installed under the CP3 in the main enclosure (4 ZZRMs if the batteries are in optional li sted battery enclosure). Add itional ZZ RMs may be enclosed in a serial device
enclosure (ZSDE) or other listed enclosure. Remotely mounted ZZRM s must be located within 20
feet of the main panel in the same room, and connected in conduit.
* Please note that to connect 3 to 4 ZZRMs requires a special-order cable, p/n 2921.
2.8 Conventional Zone Input Capabilities
The control will support up to 600 conventional points via the RS-485 bus. See Section 6 – Networking/
Serial Devices and Appendix C-3 – Co mpa tible Detectors for manufacturers and model numbers of compatible two-wire detectors.
See Section 3.0 for each device type’s operation.
2.9 Printer Output Options
The Series 3000 offers two printer output options:
1. ZSCP3The ZSCP3 offers a standard (not isolated) RS-232 p rinter or PC interface. The ZSCP3
requires the use of a DB9 Female-to-Female Null Modem cable to hook up to a printer or PC.
2. ZICP The ZICP offers an isolated RS-232 printer interface (should be used when interconnecting to
ITE listed equipment without isolated grounds to prevent ground fault problems on the S3000).
The ZICP requires the use of a DB9 Female-to-Female Straight-Through cable to hook up to a
printer or PC.
Installation instructions are included with each d evice. Section 1.4.7 outlines po rt specifications. Section
3.10 discusses the ZSCP3 / ZICP in more detail. Appendix K explains printing in dept h.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 39
3. System Controls and Operation
The following section describes the switches and annunciation control capabilities. The panel has
been divided up into four areas presented below in Figure W-12 and is described herein. The display features an 80-character LCD screen with backlighting, nine system status LED indicators,
and 16 function keys.
3.1 System Display and Annunciation
Figure W-12—Local Programming Display
3.1.1 LCD Screen
The 80-character LCD screen displays all messages and information about the system. It is also
used to display program menus, the t ime and date, and company name.
3.1.2 LED Indicators
The system condition LED indicators are provided to indicate System Alarm, Trouble, Su pervisory
conditions, and Alarm T rouble, and Supervisory Silenced conditions. Other LEDs indicate the status of AC Power, and Offline condition, and Test Mode.
LCD Screen
Panel
Control
Keys
LED
Indicators
Function
Keys
12 3 45
67 8 90
…
ABC
DEF
GHI JKL
MNO
PQRS
TUV WXYZ ./-
PROG STATUS
TEST
PRINT DRILL ESCAPE
ENTER
SILENCE RESET
NEXT
PREV
ALARM
TROUBLE
SUPERVISORY
SILENCE
AC POWER
OFF LINE
TEST MODE
CLASSIC 2000 Mk I I
ADDRESSABLE FIRE ALARM CONTROL PANEL
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 40
3.1.3 Panel Control Keys
To the rig ht of the LCD screen are two panel control keys labeled NEXT and PREV . These two
keys allow y ou to view more menu options when availab le. A down arrow on the lower right hand
side of the LCD screen or an up arrow on upper right hand side of screen indicates another
screen, therefore press the NEXT or PREV keys to access. These two keys also advance to the
next character or number when en tering individual informati on into the panel.
Below the LCD screen, the panel control keys SILENCE and RESET are found. These keys allow
you to silence alarms and troubles and reset any off-normal condition. When the SILENCE key is
acti v ated, the panel’s sounder and Notification Circuits will be silenced and the corresponding
Silenced LED will il luminate and flash until the panel is r eset or until ano ther alarm is sensed. A
second alar m condition will cause all previously silenced alarm conditions and the panel sounder
to resound its audible tone. The RESET ke y is us ed t o r e se t t he sy st em at an y t im e in a ny m enu or
mode.
Pressing the RESET key will return the panel to normal operating mode, clear any off-normal condition from the status display; restore the ala rm relay to normal state; extinguish all status LEDs
except the green AC LED; and send a message to the display and printer that a System Reset has
been performed.
The ESCAP E and ENTER panel control keys are found to the right of the function keys. The
ESCAPE key allows you to exit any menu at any time without saving the information to the panel’s
memory and automatically moves to the previous screen. The ENTER key s tores the programming
selection into the panel’s memory and automatically moves to the next option screen.
3.1.4 Function Keys
The function keys are found below the SILENCE and RESET keys. T hese keys serve several
purposes. The first five keys display menus that control the panel, its programming, and any other
function needed for the system operation (PROG, STA TUS, TEST, PRINT , DRILL; see section 3.3).
Second, these keys serve as a numeric and alphabetic keypad used during menu operation. The
second five keys also serve as Hot Keys; see section 1.5.5.
3.1.5 Alphanumeric Keypad
To access a number, press the respective key once (the panel is automatically set up as a numeric
keypad). To access the alphabetic keypad, press the respective key twice. The first letter on the
selected key will appear. To select the second letter, press the key again, and another time for the
third lett er.
3.2 System LED Indicators
3.2.1 Alarm
When th e sy stem has de tected an alarm, an a udible tone will sound and the red LED Alarm light
(to the right) will illuminate. These lights will disengage when the alarm has been re ctified and the
system reset.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 41
3.2.2 Trouble
The Trouble LED will indicate any problem with the system. An audible 3-beep tone will sound and
the yellow LED Trouble light (to the right) will illuminate. These lights will disengage when the trouble has been repaired and the sys tem will automatically restore itself.
In addition, when one of the function keys (PROG, STATUS, T EST, PRINT, DRILL) is in use, the
yellow LED Trouble light (and the off-line LED) will illuminate, indicat ing an o f f-normal condition.
3.2.3 Supervisory
The Supervisory indicator will illuminate when a corresponding input programmed for supervisory
operation is activated. The system will sound a sequence of 2 beats on, 1 beat off and the associated output groups will be activated. Output group 97 is the default output group for supervisory
conditions.
3.2.4 Silenced
The Silenced LED condition ha s three illuminating lights: Alarm, Trouble, and Supervisory. When
any one of these audible tones have been silenced, the Silenced LED will illuminate and blink indicating which condition has been silenced.
3.2.5 AC Power
When AC power is present, the green AC LED is illuminated.
3.2.6 Offline
When the panel is in other than it s normal operating mode, the yellow Offline LED illuminates.
Offline conditions include program, test, drill, and pr int. In addition, when the system is in reset
mode, the yellow Offline LED will illuminate. NOTE: The system automatically resets itself if le ft in
any offline mode. See Section 3.4.6 for the timeouts for each offline mode.
3.2.7 Test Mode
The yellow Test Mode LED illuminates when the system is being tested or a drill is being performed. This light i lluminates when the TEST or DRILL function keys are in use.
3.3 Function Keys
The first five numeric keys on the panel access the main functions of the Classic 2000 Mk II. All
progra mming , test i ng, status checks, and fire drills are done using these function keys and their
respective menus. The following sections describe the five keys: PROG (programming), STATUS,
TEST, PRINT, and DRILL. Appendix D contains the Basic O perating Inst ruct ions sh eet. This onepage instruction sheet is available for copying and posting next to the control panel for easy reference.
3.3.1 Programming (PROG)
The panel is factory-programmed with a set of default settings allowing basic system installation with
virtually no prog ra mm in g . Th e PROG key accesses all programming menus for individual programming of the system. Refer to Section 4 for specific instructio ns and details about this fu nc tion key.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 42
3.3.2 Status
The STATUS key allows the user to obtain the current status or history of the system at any time. It
browses the event history, checks an individual device status, reviews t he power supply status, and
check s what ver sion s o f hardware ar e at t a c hed t o the system. Upon entering the STA TUS menu,
these four choices will appear: Event History, Device Status, PSC, and Versions.
The Event History menu reports information on alarms, troubles, and status, basically telling you
everything that ha s happened or is happening to the panel. The Event History menu has two
modes: “Event History” and “Active Events.” If there are no active events, Event History will report
everything that has happened to the panel from the beginning. If there are any act iv e e v ents , Event
History will report only active events. The Event History menu offers three choices:
Status will tell you how many ev ents hav e happened or are active, depending on the mode. By
pressing “1,” you get a break down of events, i.e. how many are troubles, how many are supervisory, etc. It will also tell you how full the Event History log is in percentage.
Browse will let you page through each event, reporting the time, date, location, and type of
event.
Filter allows you to choose what events can be viewed in the Browser . By pressing “3” you can
choose to view any combination of Alar m, Trouble and Status e vent s. Note: Waterflow events
are grouped with Alarms; Supervisory events are grouped with Troubles.
Device Status lets the user obtain the status of a particular point. After selecting the Device Status option, use keys 6 and 7 to change the loop you are browsing. Use the PREV and NEXT keys
to move between points on the loop. Use the “0” (zero) key to toggle between viewing all points or
just in sta ll e d points.
To check the conditions of the power supply controller, the PSC menu is used. This menu shows
the version of the power supply controller, voltage of the battery, status of the backup power and
primary powe r supplies, and the status of the battery charger and its charging curr ent.
The Versions screen indicates the version of so ftware found in the panel.
3.3.3 Test
The Test key offers t h e abil ity to test variou s facets of the pane l and associated devices. Six categories are provided in the T est menu, including: Walk, NAC, Rela y, Display, CP3, and Mapping. For
more details on these func tions, see section 3.4.7. Note: this is a privilege-restricted area
requiring a Level-One Access Privilege Code (APC); the default pass c ode from the factory
is 11111. (To change APC, refer to Section 4.2.2.3 – Access Codes.)
3.3.4 Print
The Print key offers the ability to print Event History and Programming information. The user may
print all information in either category, or only specified information. Printing may be entirely disabled, selected for manual operation (prints when you hit the Print key) or automatic (prints as
events occur). Section 4.2.2.1 explains how to set these options. I nformation may be printed either
to a serial printer, or to a log file on a PC. For directions of how to print, see Appendix K –
Printing Operation.
3.3.5 Drill
The DRILL key allows for a fire drill, tur ning on all NACs, but not transferring relays. Upon completion of the fire drill, press any key and the system automatically resets. NOTE: This is a privilege-
restricted area requiring a Level One Access Privilege Co de (APC ); the default pass code
from the factory is 11111. (To change APC, refer to Section 4.2.2.3 – Access Codes).
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 43
3.3.6 Programmable Input Keys
Ke ys 6-0 are not programmed by the f actory, but are left to the user to program these “Hot Keys” for
extra functions. By using t he point programming screens, the user can assign output groups to be
controlled by the press of a Hot Key. (See section 4.2.6.)
Thus, the Hot Keys become addressable control points. They are located on loop “0,” and occupy
the address range from 30-34 (0:30 – 0:34)
3.4 System Operating Modes and Annunciation
3.4.1 Normal Operation
The following functions will be performed at regular intervals when in normal mode:
1. Supervis es all SLC devices, network devices and the four notification appl iance circuits
2. Checks for valid replies, alarms, troubles, etc.
3. Checks for power supply and battery condition
4. Supervises th e LPD interface and verifies proper res p o ns e
5. Refreshes LCD and ZRDA/ZRPD displays and updates time
6. Scans keypad for System RESET
7. Performs sensor auto test
8. Supervised ZZRMs, ZCBM, Network communications, PSC communications and operation
9. Performs time-scheduled actions (day/night sensitivity and on/off schedules)
3.4.2 Trouble Operation
With no alarms, the detection of a trouble in the system will cause the piezo to sound a coded output - three rapid pulses, then a pause, three rapid pulses, then a pause. The System Trouble LED
will illuminate, and the trouble relay will activate. The following is a typical message that could
occur on the Panel LCD. The same message is sent to the ZRDA, printer, and history file.
The first line lists the type of event code – TR (trouble), Event Number – 45, and the Loop and
Address where the event occurred. The second line is the Date and Time (in 24-hr. format) of the
event, and the third line contains a description of the Trouble Event Type. The system will toggle
between an event summary and the ev ents in the order of occurrence. The Active Event Summary
Screen would appear as follows:
Figure P-1
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 44
The system toggles between events and the event summary about every 2.5 seconds. If more time
is needed to examine the events, you can press either the NEXT o r PREV keys to enter a Qu ickBrowse mode. Continue using the NEXT and PREV keys to page through the active e vents at your
leisure. Warning
! Using the Quick-Bro wse mode will take you offline. Press Escape to go
back online.
When events occur, you also have the ability to view point labels for troubles that normally display
an event message by pressing “0”. For example, a trouble might report “SLC Device Missing.”
Pressing “0” might chan ge t he s c re en t o s ay “Input Module,” naming what kind of SLC device is
missing. This works whether t he panel is onli ne or offline. Note: this function is available online
only if key “0” ha s n ot
been program m ed as a Hot Key.
3.4.3 Silence Operation
Pressing the SILENCE button will cause the piezo to silence and the Silenced LED to flash. This
occurs regardless of the number of troubles, alarms, and supervisory signals in the system (global
silence). When SILENCE is pressed and at least one new alarm or trouble ex ists in the system, the
Silenced message is sent to the printer and history file.
If the trouble clears (and troubles are configured as non-latching), either before or after Silence
Event, the Trouble Restore message is sent to the displays and printer. If all troubles clear and
there are no supervisory or fire conditions in the system, the syste m retu rn s to n o rmal opera tio n
status, and the All Systems Normal message is sent to the LPD, ZRDA, history file, and printer.
This trouble restore occurs even if the troubles were never acknowledged (auto restore).
If multiple trouble conditions exist in the system, the LPD and ZRDAs on the system will step
through them automatically at three-second intervals.
3.4.4 Alarm Operation
Alarm operation is similar to Trouble operation, but with the following differences:
1. The piezo is pulsed -- 0.5 seconds on 0. 5 seconds off
2. The System Alarm LED illuminates
3. The Display reports an Alarm event (AL) with the addres s, date, and time in the top two lines
4. The label of the point in Alarm is displayed in the third and fourth lines
5. Alarms latch and are not allowed to clear
6. Alarms cause recalculation of all control-by-event
7. Timers (Silence Inhibit, Auto Silence) are started
8. Alarms activate the general alarm relay, Group 99, and other Output Groups the input is
mapped to.
Figure P-2
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 45
The following is a typical alarm display:
3.4.5 Supervisory Operation
Supervisory operation is similar to trouble operation, with the following differences:
1. The piezo is a coded sound – Long pulse, a short pause, rapid pulse, then a long pause
2. The Supervisory LED illuminates
3. The display reports a Supervisory Event (SP) with address, date and time in the first two lines,
the label is displayed in lines 3 and 4
4. Silenced ala rms are not resounded
5. Timers are not started
6. The alarm relay is not activated (auxiliary relay p r ogrammed for supervisory operation
is activated)
7. Supervisory Group (97) is activated, along with groups mapped to the input.
A typical Supervisory event would display:
Supervisory signals, like alarms, latch and control output groups. They do not cause resound of
alarms or rea c tivation of silenced alarms.
Figure P-3
Figure P-4
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 46
3.4.6 Program Mode Operation
When another mode is selected at the keypad (other than normal operating, alarm or trouble operation modes), the system is considered in an off-normal mode, the offline LED illuminates, the
trouble LED illuminates, and the trouble contacts will transfer . The panel has built in safeguards
that prevent it from being left in an o ff-normal mode. Each mode has a bui lt in timeout that will
automatically retur n th e panel to normal operating mode when the allot ted time expires:
Access Level Timeout 180 seconds
Program Menu Timeout 180 seconds
Menu Level Timeout 300 seconds
Walk Test Mode Timeout 3,600 seconds
Status Timeout 600 seconds
Drill Timeout 600 seconds
At the expiration of the safety timeout feature, the panel will reset, locking in any programming
changes, and return to normal operating mode.
3.4.7 Test Mode Operation
The Test function key provides a menu w ith six test categor ies: Walk, NAC, Relay, Display, CP3
and Mapping. Note: This is a privilege-restricted area requiring a Level One APC; the default
pass code from the factory is 11111. Please refer to section 4.2.2.3 – Access Codes.
Walk mode is used to perform a walk-through test of any or all devices in the system. There
are two ty pes of walk tes ts that can b e performed. A Normal walk test will cause all out pu ts
(horns, strobes, etc.) to sound simultaneously with the panel as each device is tested. The
panel will sound one long beep for an alarm; two for a trouble. During a Silent walk test, only
the panel will sound, giving one short beep for an alarm; two for an alarm restoral; three for a
trouble; and four for a trouble restoral. During either test, the panel will report the event (alarm
or trouble), address, type and label of each device test ed. T he same information will print out
at the PC or printer, if that option has been activated (see Appendix K). A “+” (plus) by the
event indicates an active event; a “-” (minus) indicates a restoral. Upon completion of the walkthrough test, press ESCAPE and the system will return to the main menu.
NAC (Notification Appliance Circuit) mode allows you to test and turn off the circuits for horns,
strobes, and any other audible / visual notificati on devi ces. Note: This tes t does no t apply
when NACs are programmed as Auxiliary Power Supplies.
Relay allows you to turn any relays on and off , including the on-board trouble and alarm relays,
as well as any ZZRMs. As you test the relays, listen for the clicking noise as they turn on and
off, and take note of any associated LEDs, to verify the relays are working.
Display tests the LCD screen and LED lights to verify operation. Pressing this option will illuminate all LED and LCD screen lights. If any do not light, contact Zeta Alarm Systems.
CP3 test is basically a panel self-test and tells the user what is or isn’t installed directly to the
panel. One useful feature is the Ground Fault display. Since this is a live report of any ground
fault situation, you may go to this screen and watch to see when the fault disappears while you
troubleshoot the connected hardware.
Mapping allows the user to simulate an alarm or trouble for each point. The purpose of this
function is to verify that the mapping is correct. For example, a particular photo sensor needs to
be tested. Press 1 to set it into alarm. Press RESET to turn it off. Press 2 to send it into trouble.
Press RESET to turn it off. Watch for the appropriate NACs, horns, strobes, LEDs, etc. to go off
when the device is sent into ala rm or trouble. This will help verify the mapping of the device.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 47
3.4.8 Sleep Mode
In the event of a loss of AC Power, the panel automatically transfers to energy conserving “Sleep”
Mode. As with any trouble condition, the yellow Trouble LED will illuminate and the local trouble
sounder will annunciate a trou ble condition and the trouble “AC Fail” will be dis played. In the sleep
mode:
A The backlight will extinguish
B The Trouble LED will illuminate
C The trouble contacts transfer* unless programmed for delay to comply with NFPA 72 Central
Station or Remote Station operation (see Section 4 for operation and programming)
*If the system is programmed for NFPA 72 Central Station or NFPA 72 Remote Station operation, the system must be programmed to delay transfer of trouble contacts.
If the trouble condition is silenced, the trouble silenced LED flashes to designate it is silenced.
If an alarm condition occurs, the display illuminates and enunciates the alarm condition and the
panel returns to no rmal operation on DC power. When AC Power returns, the green AC LED will
illuminate, the Trouble LED will extinguish, and the panel will return to normal operating condition.
In the event of a delay as abov e, local annunciation remains the same. Please refer to Section 5 for
information regarding operation and programming of dialer application trouble delays.
3.4.9 Watchdog Circuit Operation
Should the microprocessor fail, the processor automatically attempts to reset the system. Should
the processor be unable to reset, the trouble contacts transfer a nd the local trouble sounder will
sound a solid tone that cannot be silenced.
Should a microprocessor failure occur, call your authorized representative at once.
3.5
Notification Appliance Circuit (NAC) Operation
The four output circuits may be programmed as Notification Appliance Circuits or 24VDC auxiliary
power outputs. The outputs are programmable for event- or time-based operation and function
similar to output modules on the SLC loop. NACs may be used for Continuous Output or coded
functions - March Time or Temporal, and Two-stage (Sounder output modules may not). NACs may
be silenceable (for horns or bells) or continuous (for strobes).
Notification Appliance Circuits may be programmed at t he global system level for certain timing
operations including: Silence Inhibit for up to 5 minutes and Auto Silence from 0, 15, or 30 minutes.
3.6 Addressable Sensor Functions
The addressable smoke and temperature sensors are sensors, not detectors. They conv ert analog
values read at the sensor head and communicate the values back to the Classic 2000 Mk II control panel where decisions are made based on the sensor’s readings. Following is a review of the
features and functions relative to the sensors that are available from the control system.
3.6.1 Analog Display
The control panel reads and di splays analog information from the sensors. The display is the analog value that relates to percent obscuration per foot for photoelectric and ionization sensors and
degrees for thermal sensors. Analog values are 53-73 for ion sensors, 35-70 for photo sensors,
and 25-115 for thermal sensors. Refer to Appendix I for tables that convert the analog values to UL
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 48
obscuration percentage conversion for the photo and ion sensors and degrees Celsius to degrees
Fahrenheit conversion for the thermal (heat) sensor.
3.6.2 Sensitivity Adjustment
Alarm levels for the intelligent sensors may be manually set within the UL range. There are three
system-level programmable settings: High, Medium, or Low. Values associated with the High,
Medium and Low settings are user programmable within the UL approved range. Each sensor may
then be set to one of the three levels. Additionally, each sensor may be micro-adjusted using the
“offset” menu to adjust the sensitivity setting up or down 3 analog counts. Note : Ionization sensors
used in duct applications must be set to high sensitivity. See Section 4.2.4.2.
3.6.3 Day/Night Sensitivity Adjustment
The system can be programmed to automatically adjust the smoke sensors to a lower sensitivity
during times the location is normally oc c upied (“day”) and to return to a more sensitive setting
when a location is not occupied. For more information, see information on Day/Night Sensitivity
Control programming and operation in Section 5.
3.6.4 Alarm Test Level Measurement
The panel software periodicall y commands each sensor to s imulate an alarm level readin g fr o m
the sensing chamber.
Please see Appendix I for a table converting the analog value reading to %/ft. obs curation based
on its position between the known clean air and test values . The accuracy of this measurement
method is sufficient to meet the NFPA 72 requirements as a calibrated smoke test instrument.
3.6.5 Automatic Test Operation
The control panel performs an automatic test of each sensor once every 24 hours. Failure to meet
the test limits causes a Service Alert trouble type. System Reset clears this trouble. Panels incorporating the ZNDC for event reporting will send a “Periodic Test Repor t” event to the Central Station. See Section 6.1.6.
3.6.6 Maintenance Alert Operation
When the compensation reaches the limit of the amount of drift compensation that may safely be
applied, a special trouble condition is reported, per new NFPA standards.
3.6.7 Type Code Supervision
The control panel monitors hardware device type codes on a regular basis. Mismatch of type compared to the program will cause a point trouble. Trouble label is DEVICE TYPE WRONG.
3.6.8 LED Control Operation
The panel includes a global program selection to prevent blink of sensor LE Ds during normal conditions. This is often desired in sleeping a reas where the flashing light may be objectionable. As a
standard function, the control panel allows up to 5 LEDs per loop to latch on in alarm.
3.6.9 Alarm Verification Operation
The panel performs alar m verification on selected intelligent smoke sensors. Selection of sensors
for alarm verification is described in Section 5. The verification time is a global system program
selection of 0 to 60 seconds.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 49
3.7 Addressable Module Operation
There are three basic types of Mod ules available on the SLC loops:
Switch (Contact) Monitor Modules
I/O Module
Sounder Control (Output) Module
3.7.1 Contact Monitor Module
The contact monitor module is available in two package sizes and two operating modes:
Priority Mini Monitor Module (P/N MPM-830)
Priority Monitor Module (P/N PMM-806)
The regular modules are packaged to moun t into a 4-square back box. The Mini-Modules are
reduced in size to mount in a single gang box.
The priority module will interrupt the panel’s polling function when initiated, and provide a faster
response to initiation. All Monitor Modules may be programmed to perf orm the same functions.
Contact Monitor Modules may be programmed for any of the following operations:
Alarm Input – defaults to Group 99 with ass ociated functions – latching
Manual pull station – defaults to Group 99 with associated functions – latching
Waterflow alarm input – defaults to Group 96
Supervisory alar m input – defaults to Group 97
Remote Drill Test input – functions identical to Dr ill button on the LPD
Remote Reset input – functions i dentical to Reset button on the LPD
3.7.2 I/O Module
The input / output module functions in two modes. When selected as an I/O-input, a set of Form C
contacts follow that input (if the input is activated, the Form C contacts energize or change state).
Input defaults to Group 99. When selected as an I/O-relay, the module functions as an output and
may be included in up to 5 output groups (the input is ignored).
Note: The I/O module defaults to relay. This may be changed on the Point Edit Screen (see Appendix E). Also refer to Appendix L for Mapping discussion.
3.7.3 Sounder Output/Sounder Control Module
The Sounder Output modules control and supervise compatible 24VDC notification appliances.
Each Sounder O utput has the following programmable attributes:
Silenceability
All Call
Output Schedule
Output Group Assignme nts
Courtesy Labe l
3.8 Network Operation
The Classic 2000 Mk II panel is able to communicate with up to 127 devices over an RS-485 network. Network devices are both powered by and communicate through the RS-485 network. Zeta
Alarm Systems offer several devices that connect to the panel via the network, including: ZRDA,
ZTZB, ZFZA, ZRPC, ZACM, ZRLD, ZCBM, ZNDC, ZDIO, and ZPNI-S1K. See section 2 for wiring
diagrams, and section 6.0 for an in-depth explanation of the network and associated devices.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 50
3.9 Zeta Zone Relay Module (ZZRM) Operation
Up to four ZZRMs may be connected in series t o the ZRM port in the lower left-hand cor ner of the
board. A ZZRM module contains five relays that may be programmed individually as system
relays. The relays are automatically as signed addresses on loop zero. The first ZZRM occupies
addresses 10 – 14 (0:10 – 0:14), the second, addresses 15 – 19, and so on.
Two steps are needed to make sure that the panel will recognize any ZZRMs. First, the panel must
be told ho w many ZZRMs will be connec ted to the panel. Refer to section 4.2.5.2 for programming
instructions. Second, pins 1 and 2 on the ZZRM fur t hest from the CP3 must be jumpered. If any
module but the furthest ZZRM is jumpered across pins 1 and 2, the panel will see only as far as
that ZZRM. All other ZZRMs should be jumpered across pins 2 and 3. Refer to section 2.7.1-a for
installation diagram.
3.10 Zeta Serial and Isolated Communication Ports (ZSCP3 / ZICP) Operation
An RS-232 communication port may be added to the panel to provide a way to talk to a printer. The
small board attaches to J9 and J2 of the panel, just above the ZRM port, and connects to the
printer via a DB9 female-to-female cable.*
There are two types of communication ports: Isolated and Seria l (Non-Isolated). Note: it is nor-
mal for the panel to report a ground fa ult when an ZSCP3 is installed and connected to a
printer or PC. The isolation of the ICP will prevent ground faults and is therefore the device recom-
mended by Zeta Alarm Systems. Also, the ZSCP3 / ZICP does not reside on the network and
therefore does not get scanned in. The device is automatically detected by the panel at RESET.
However, the panel can be programmed to print either automatically, or on command. See section
4.2.2.1 for programming directions. Note: the ZSCP3, ZICP use 9600 baud, 8 data bits, 1 stop bit,
no parity.
There are actually several ways to get information from the CP3 to a printer. If an ZSCP3 / ZICP is
not installed, the CP3 prints out the Program Port at J2 using the PCI cable (p/n 3000-6015). If
ZSCP3 / ZICP is installed, data will print through the DB9 connector instead. If any remote printers
are at tached to the network via a PNI board, the panel will print through those printers instead of
an ZSCP3 / ZICP or Program Port (J 2).
*NOTE: The ZSCP3 requires a Null Modem cable; the ZICP requires a Straight-Through
cable. Both cables must be DB9, Female-to-Female.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 51
4. System Programming
The Classic 2000 Mk II can be programmed two ways – through the keypad found on the panel or
by using your PC and a sepa rate program supplied by Zeta Alarm Systems. The following section
describes the steps and infor mation necessary to program the system using the panel keypad. A
separate operations manual accompanies the P C program.
Please refer to the Programming Summary Chart (in Appendix E) for a complete overv iew of programming options, access levels required, and program defaults.
4.1 Before You Begin Programming
Programming is broken down into 7 basic steps controlled by access privilege codes (APCs), plus
two other menus that control the clock and allow for PC programming. The programming theory
allows you to establish parameters on the system level, reducing the amount of specific information required to be programmed at the SLC device level.
The panel features a combination of single pur po se and multi-purpose keys allowing complete
control of the system. Single purpose keys include scrolling keys (NEXT and PREV), SILENCE,
RESET, ESCAPE, and ENTER (detailed in Section 3.1). The multi-purpose keys are alphanumeric
keys (0-9 and A-Z) and activity selections keys PROG, STATUS, TEST, PRINT, and DRILL
(detailed in Section 3.3). After an activity selection is made, the keypa d will auto m at ic a ll y ent er
numbers or alpha characters dependent on the screen requirements.
To enter a l abel, press the number key with the associated alpha character on it until the desired
letter appears, then press ENTER. The “1” key will give you a special character set to choose from.
Just use the NEXT and PREV keys to move the cursor to the character you wish to select, then
press ENTER.
Note: When browsing, use keys 6 and 7 to move between the loops. PREV and NEXT are
used to move between points on a loop. Key 0 toggles between “View All Points” and “View
Only Inst a lle d Points.”
4.1.1 Access Privilege Code (APC)
Any user with a key to open the front panel may silence and reset the panel, step through the status and history events, print the event history, and set the time, date, and time mode without entering a pass code. This is referred to as Level 0 access. For access to other pr iv ilege-restricted
areas of the programming menu, the user will be prompted for a password, which does not expire
until 3 minutes after the last keystroke.
Aside from the Level 0 access, there are also Levels One and Two APCs. System Test menus and
operation require a Level One APC; and all programming menus require a Level Two APC. Default
Pass Codes from the factory are “111111” for Level One and “222222” for Level Two. Custom Access Privilege codes are e stablished within the programming menu. See Section 4.2.2.3.
If an incorrect APC is entered three times in succession, a recovery code will be displayed. The
user may call the Zeta Alarm Systems technical support department (+44 1792 470394) to convert
the recovery code into an APC, or e-mail the recovery code to nrpj@zeta-alarms.fsworld.co.uk
for
immediate response.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 52
4.2 Program Menus
To begin programming the system using the panel keypad, press the PROG function key. A menubased approach allows each of the programmable functions to be selected or bypassed by pressing a single key. There are 9 menus found under Program: Clock, System, Network, Inputs, Outputs, Points, Groups, PC Communications, and Factory Defaults (illustrated below). The following
sections describe each menu in detail and include an illustration of each main Program
Menu display.
NOTE: When programming, the ESCAPE key allows you to exit any menu at any time without saving the information to the panel’s memory and automatically move to the previous
screen. The ENTER key stores the programming selection i nto the panel’s memory and
automatically moves to the next option screen.
4.2.1 Clock
The Clock menu allows you to set the time, date, and ti me display mode (12- or 24-hour display).
To change e ither the Time or Date, press the respective number, edit in place, then press ENTER.
Press 3 (Mode) to toggle and select 12- or 24-hour clock modes. Then press ENTER to store the
information in memory.
Figures P-5 & P-6
Figure P-7
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 53
4.2.2 System
The System parameters allow you to program system options by toggling between system
defaults and available options or entering n umerical values. There are four menus associated with
this area of programming: Options, Timing, Access Codes, and Edit Banner Message. NOTE: This
area requires a Level Two APC to begin.
4.2.2.1
System Options
The System Options menu presents all the general system operati on setti ng s. Th e s e include trouble latching operation (LatchTroubles), trouble reminder enablin g (TroubleRemind), waterflow
silenceability (WaterflowSil), printer operation (Print er) , and floor above/below configuration (FloorConfig). Each menu is toggled by pressing the associated number (1, 2, 3, 4, or 5) to display the
possible options available under each menu option.
Menu Option 1 – Latch Troubles: XXX - Press 1 to select yes. A “yes” selection will cause all
trouble conditions to latch. Latching means that all trouble conditions will require the trouble to be
resolved and the system reset prior to returning the system to normal operating condition. Press 1
again to select “no” and allow a trouble-restore operation. A restore operation will return the panel
to normal operating condition when a trouble condition has cleared or resolved. Any relays not
selected for a latching operation will return to normal state, and a ‘trouble-cleared’ message will be
sent to the event history.
Menu Option 2 – TroubleRemind: XXX - Select yes to silence trouble conditions and provide an
audible “error” signal every 5 minutes. Subsequent new Troubles will cause trouble operation to
resound, and Silence will recycle the 5 -minute trouble reminder signal.
Menu Option 3 – WaterflowSil: XXX - The panel default setting is “no” in compliance with NFPA
requirements. When “no” is selected, any alarms caused by waterflow devices monitored by this
panel will not respond to the panel’s silence function. “Yes” will allow the alarm to be silenced. This
option allows compliance with some local AHJs (Authority Having Jurisdiction).
Menu Option 4 – Printer: XXX - Establishes Printer settings. “Disabled” means no printer is
installed or the output is turned off. “Manual” will output the selected items only when you select the
print menu, and “auto” w ill automatically send data as it occurs and is sent to the event history log.
Menu Option 5 – FloorConfig: XXXX - This setting (in concert with the “floor” parameter of eac h
output group) determines the operation o f the panel’s “floor above / floor below” function. The settings are as follows: “1 Above / 1 Below” = 1A/1B; “2 Above / 1 Below” = 2A/1B; “1 Above / 2
Below” = 1A/2B; or “2 Above / 2 Below” = 2A/2B.
Figure P-8
Figure P-9 Fig ure P-10
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 54
4.2.2.2 Timing
The Timing menu allows you to establish AC Power Fail reporting delays, Auto-Silence of Alarm
and Trouble Time, Silence Inhibit Time, and Alarm Verification times. In addition, this menu allows
for individual system programming for Holidays, Day/Night Schedu les, an d On/O ff Schedules.
Menu Option 1 – AC Low Delay: XXh - To select AC power fail time for UL Central Station or
Remote Station Operation (AC Low Delay), use key 1 to choose between a 0, 8, or 16 hour delay
for reporting the AC Low/Fail trouble condition to the monitoring service. Other panel troubles will
be reported im mediately.
Menu Option 2 – Auto Silence: XXm - The Auto Silence mechanism can be set by pressing 2
and toggling between 0, 15, and 30 minutes. This will automatically silence alarm and trouble
alerts after the specified time.
Menu Option 3 – Silence Inh: XXs - To provide a silence inhibit period, Silence Inh is sel ected b y
pressing 3 to toggle between 0, 30, 60, 90, 120, 180, 240, and 300 seconds. This sel e c tion will
prevent silencing of all enabled NAC or sounder outputs for the specified time.
Menu Option 4 – Alarm Verify: XXs - Pro gram t h e a l arm verificat i on time (Alarm Verify) by
pressing key 4 and entering any amount of time from 0 to 60 seconds. This sets a period of time in
which the panel can confirm an alarm condition on inputs t hat ha ve been selected for Alarm Verification before rep orting an alarm. Alarm verif ication is only available for photoelectric and ion-
ization sensors. Only use compatible sensors listed in Appendix C. Alarm verification may
not be used with devices having their own alarm verification capabilities.
Menu Option 5 – Holidays - P r ogram up to 18 annual holidays to work in conjunction with day/
night sensitivity schedules. Select 1 to specify the first holiday . Enter the month, then press ENTER
to move to the day of th e month. Enter the day of the month, then press ENTER to complete the
first holiday. Press ESCAPE to back up to the previous field should you need to make a correction.
Menu Option 6 – Schedules - On/Off Schedules and Day/Night Sensitivity Schedules. T o select a
schedule to program, press 1 - 4 to select a Day/Night schedule and 5 - 8 to select an On/Off
Schedule. Simply enter the values as prompted by the screens.
Figure P-11 Figure P- 12
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 55
4.2.2.3 Access Privilege Codes
The Access Code menu allows you to change codes (APCs) for Levels One and Two. Upon pressing 3, the default pass codes from the factory appear: 111111 for Level One and 222222 for Level
Two. To change them, edit in place with the new 6-digit number. System Test menus and operation
require a Level One APC; and all programming menus require a Level Two APC.
4.2.2.4 Edit Banner Message
The Edit Banner Message (Edit Banner Msg) menu allows you to c u stomize the label shown in the
80-character LCD display. Using the alphabe tic keypad, press the respective key twice. The first
letter on the selected key will appear. To select the second letter, press the key again, and another
time for the third letter. (For example, to program the letter “A,” press the key twice, for “B” press
again, and for “C” again. If the key is pushed again, the respective number appears.) The NEXT
and PREV keys will allow you to move from one letter to the next. Pressing the 1 key twice brings
up a character-picker screen to provide the space, common symbol, and character selections.
Pressing ENTER will lock in your alpha-numeric banner selection.
Figure P-13 & P-14 Figure P-15 & P-16
Figure P-17
Figure P- 1 8
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 56
4.2.3 Network
The Network menu allows you to scan the RS-485 network for network residents and auto-pro-
gr am, or review the ne twork residents and addresses.
The Scan key searches for all network devices. While searching, an “*” (aste ri sk ) will appear and
blink. When the search is complete, the system will display how many devices were found and
what type. To browse through the network devices, press 2.
Browse Devices. This screen displays the address, type, status of each d evice, an d firmware version, and allows you to scroll through the network of devices using the PREV / NEXT Keys. Pressing “0” (zero) when browsing will display the number of errors to that device since the last
hardware reset. This screen also allows you to establish a base LED number for the ZRLD remote
LED drivers. Pressing ENTER when th e ZRLD is desplayed produces an edit field. The LED number can be set from 1 to 2,969. NOTE: After installing a conventional in put module (ZFZA / ZTZB),
additional ZACM loop card(s), PNI card(s), o r city tie / reverse polarity modul e (ZCBM), you will
need to select Points (Option 5 in Program menu) and select Auto Program to scan the available
points i n to the panel’s programming (See Section 6 – Network Devices).
Style will toggle between Style 4 (Class B) and Style 6 (Class A) network communications by simply pressing 3.
4.2.4 Configuring Inputs
All general system input parameters are programmed from this menu. With proper access privilege, you can establish the low, medium, and high sensitivity levels for the s moke senso rs, as well
as program three te mperature levels fo r temperat u re sensor s. In addition, the auto-test time for
each type of sensor is programmed using this menu. Three choices are available for Input Configuration: Options, Sensitivity and Alerts.
Figure P-19
Figure P-20
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 57
4.2.4.1 Input Options
The Options menu includes programming the calibration time in hours and minutes. Press 1. Test
Time and edit in place the desired time using a 24-hour mode. Input the hour and press ENTER;
this will automatically bring t he c urs or to the minutes for editing. When 2 is pressed, LED Blink
allows you to toggle between “yes” and “no” for enabling or disabling the blinking of the sensors’
LEDs (note that enabling LED blink may slow loop polling performance).
4.2.4.2 Alarm Sensitivity Levels
The Sensitivity menu is used to set the high, medi um and low system settings for the ion, photo,
and heat sensors at the system level. To change the ranges for ion and photo, and set the Heat
Sensor alarm point, pres s the respective number and a screen with Low, Medium, and High will
appear. To program each range, press the respective number and edit in place. Press ENTER to
sav e th e le v el s . Not e: You will sele ct the individual device sensitivity (High, Medium or Low) in Point
Programming.
4.2.4.3 Input Alerts
Once a day, the test feature will go out and check if the analog level is above the specified maintenance or service alert level. If the analog level is above one or both of these level, the system will
sound an Input Alert. In this case, inputs will be monitored from Ion and Photo Sensors.
Figure P- 2 1
Figure P-22 Fi gure P-23
Figure P- 2 4 Figure P-25
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 58
4.2.5 Configuring System Outputs
This option configures the four 24V DC outputs of the panel and auxiliary relay functions by toggling through the options available. Output circuit options for each of the 4 NACs include 24V DC
auxiliary power (resettable or not-resettable), and Reversing Polarity continuous (steady), march
time, and ANSI temporal patterns.
4.2.5.1 Notification Appliance Circuits (NACs)
The Configure NACs menu is used to program the 24VDC output circuits found within the system.
By pressing the number corresponding to NAC 1 – 4, the menu allows you to select between five
options for each output: NAC-ST (steady output), NAC-TC (temporal code output) NAC-MT (march
time output), PS-Rst (Power Supply,Resettable), and PS-Con (Power Supply, Continuous).
4.2.5.2 Zeta Zone Relay Modules (ZZRMs)
The ZZRM screen provides the CP3 with the number of ZZRM programmable relay modules
installed on the system. When pressed, this key moves between 0 and 4 to set how many zone
relay modules are connected to the system. Each ZZRM relay can be configured as silenceable or
non-silenceable under the Points menu (see section 4.2.6.5).
4.2.6 Point Programming
The Point menu is used to automatically program the system by scanning the system, each SLC,
and the network for programmable points. The only exception is the Hot Keys, which are already
recognized by the panel, but must be mapped manually from the Point Programming menu in order
to be active.This menu also will allow the user to edit a point, or browse through the point data, one
point per screen, by pressing the PREV or NEXT keys to move between them. Pressing ENTER
allows the user to edit the point data on that screen. This menu will also include the conventional
zone inputs found when the network is auto-programmed.
Figure P- 2 6
Figure P- 2 7
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 59
Press 1. To edit point address. Enter 0-9 for the loop and 1-127 for the address. The first line
will include a 5-character device type abbreviation.
Press 2. To edit the point entered in 1 above.
Press 3. To browse through the points.
Press 4. To change device status. Pressing will toggle between enabled/disabled.
Press 5. To auto-program the panel.
Press 6. To view previous loop.
Press 7. To see next loop.
Press 0 In edit and browse menus to toggle between: “view only installed points” and “view all
points”
Press EN TE R to edi t the s pecified poin t.
Press ESC to exit the screen.
Each time a change is made in programming the system, SLC, or Network devices (adding,
deleting), you must rescan the loops (Auto-Program).
4.2.6.1 Auto-Program
When Auto-Program is utilized, it searches for all SLC, network, and system input points and
automatically records them in the panel. This is used in conjunc tion with the following menus to
browse, program, edit, add, and remove all devices for easy customization of your system. If Auto
Program finds a new device(s), it will ask if you want to accept the device on the loop. If Auto Program finds a device(s) missing when it scans, it will alert you to the absence and ask for your
acceptance. If, in either event, you do not choose to accept, a trouble will sound at reset, alerting
you to the situation.
Figure P- 2 8
Figure P-29
Figure P-30 Figure P-31
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 60
4.2.6.2 Add/Remove Point
To add an SLC point:
1. Connect the new device to the SLC and physically set an unused address for the device with
the X-per t Card for sensors, or the 8-button DIL (DIP) switch on the modules.
2. Select 6. Points from the PROG menu.
3. Select 5. Auto-Program to scan all SLC loops for the new device(s). The system will automati-
cally establish the new SLC resident(s) to their system default settings.
4. Select 1. Point: X: XXX and enter the loop numb er, then the address of the first new device
and press ENTER.
5. Edit the point as described in the following sections.
To remove an SLC point:
1. Physically disconnect the device from the loop. This will cause a trouble condition. Press
RESET, then PROG immediately after the panel establishes a normal condition.
2. Select 5. Auto-Program and re-scan the loop.
3. Press ESCAPE to exit the menu and RESET to return to normal operation.
NOTE: Only “changed” points are programmed, i.e., if a point is already programmed and its
device type matches the “new” device ty p e, t hen i t is not modified. Otherwise, the point’s programming is set to the default for that device type.
4.2.6.3 Point Location
Once all the points have been logged using Auto-Program, to access a specific point, press 1.
Point and then enter the loop and address of the spec ific point to be reviewed or edited. There are
three options available for assessing each system point: Browse, Edit, Status.
4.2.6.4 Point Programming Options - Edit
Once the Edit menu has been accessed, press:
1. Enable/Disable to turn a device on or off (note that a disabled device will cause a
system trouble);
2. Label to edit the 40-character label;
3. Mapping to assign or change the output group(s) associated with that point and assign
LED outputs;
4. Options to select any options available for that device type. For example, if editing a priority
monitor module you may select the type of monitor input from a pre-established set of options.
When editing a sensor, you select sensor sensitivity – high, medium, or low (and for further
sensitivity, the offset). When editing the points of a ZZRM, you can configure each relay as
silenceable or non-silenceable from this menu. In other words, the options vary per device.
See Appendix E for detailed information.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 61
The Options menu allows you to more precisely establish the sensitivity of the sensor, allowing you
to increase or decrease an individual sensor’s setting slightly above or below the high, medium, or
low setting.
The device type will be displayed on the bottom line of the display in the main screen.
4.2.6.5 Point Programming Options - Browse
To view point data (including NAC and SLC outputs), one point per screen, press 3. Browse. This
will step you through Loop 0 (the System level outputs, NAC, syst e m relays, Z ZRM relays, etc.),
then SLC Loop 1–8 (if install e d), a nd fi n a lly L oop 9, th e RS- 485 n etw or k input points. Use the
PREV and NEXT keys to move between points and press ENTER to edit point data. If not within
the Browse menu, press 2. Edit to edit point data. Use 6 and 7 keys to move between loops. 0
toggles be tween “view all points” and “view only installed points.
4.2.6.6 Point Programming Options - Status
The Status menu allows you to temporarily enable or disable any system output or input point. To
change the status, toggle between “disabled” or “enabled .” When browsing, an “E” w ill dis play in
the upper right corner of the display when a point is enabled.
4.2.7 Output Group Programming
The system allows you to establish up to 199 output groups. Each output point may be a part of up
to five output groups. It is possible to access any group data by pressing the option 1 (Group) key
and entering the group number from 1 to 199 and pressing ENTER. After a group number has
been entered, you can then browse or edit that group. Prev/Next moves between groups, ENTER
allows you to Edit the point. Note: special output groups will be designated in this screen; general
output groups will have no designation bes ide the group number. Also, see Appendix L for a discussion of mapping.
Figure P- 3 2
Figure P- 3 3
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 62
4.2.7.1 Browse Group
Selecting the (2.) Browse Group option will allow you to step through the output groups one at a
time, viewing the group’s characteristics including output group number, floor (if using floor above/
floor below operation), alarm count, and group courtesy label will appear on the screen. While
viewing the output group data, use the PREV and NEXT keys to m ove between groups. Press
ENTER to forward directly to the edit group menu.
4.2.7.2 Edit Group
The Edit Group menu allows you to modify the characteristics of each output group in the system
with five options to choose from Enabled, Floor, Cadence, Count and Label. To t urn a group on or
off, the user simply presses 1 to toggle between Enabled and Disabled.
To utilize the floor above/floor below operation, press (2.) Floor and enter the floor number for the
output group being edited (refer to Section 5.4.4 for floor above/below programming and operation). Floor: 00 means the group input is not included in floor above/below operation (floor number
will be dashed out). Any other number will establish it in the floor above/floor below matrix
operation.
Use the (3.) Count menu to establish a multiple alarm group. Each output group has an “alarm
count” property which may be set from 1-9 (default is 1). Each group keeps a count of how many
inputs in that group have gone into alarm. When the number of devices in alarm meets or exceeds
the alarm count for that group, the group is activated. The general al ar m group (g roup 99) always
activates when any alarm occurs.
Press (4.) Label to input or edit a courtesy label for any output group. Once the key is pressed, use
the alphanumeric keypad to edit th is 20 -c ha ra cter label (the c our te sy label displays only when
printing programming, not when the group is activated).
Figure P- 3 4
Figure P- 3 5
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 63
4.2.8 PC Communications
The Classic 2000 Mk II provides two ways to program the system. In addition to the simple keypad
programming described in this chapter, programming from your PC is also available. If you are
using the Windows 3.1 or higher based software, please follow the inst ructions below.
To download system, point data and lab els from a PC or laptop, select (8.) PC Communi c a ti on s
and plug the PC cable into the programming port on t he CP3. Follow the instructions with the software to accomplish panel to PC communication and load your programming database. When completed, press any key and the panel will automati c ally reset.
NOTE: The PC-3K Programming software and cable is an option and has its own
Operation Ma nual.
4.2.9 Factory Defaults
The Factory Defaults menu allows you to restore the panel to factory-set default values for all programming options (except pass codes). The display will ask you to confirm that you want to reset
the panel. Press 1 to reset and 2 to return to the main menu.
Resetting the panel to factory defaults will clear al l edited values.
Figure P-36
Figure P- 3 7
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 65
5. Special Application Programming
and Operation
5.1 Local Protective Signaling System
At least one audible appliance must be installed.
5.2 NFPA 72 Central Station
Please refer to section 1.3.1.2 for the UL minimum requirements for a central station monitored
system. To program the panel for NFPA 72 Central Station Operation requires two steps:
1. Establish the AC Fail delay in the System Level
Select PROG function key
Select Item 2 – System ss
Select Item 2 – Timing
Select Item 1 – AC Low Delay and toggle to select 8-hour delay
2. Connect Z e ta Alarm S yst ems’ UL listed and compatible ZNDC dialer as shown in Appendix F.
5.3 NFPA 72 Remote Station
Please refer to section 1.3.1.3 for the UL minimum requirements for a remote station monitored
system. To program the panel for NFPA 72 Remote Station Operation requires two steps:
1. Establish the AC Fail delay in the System Level
Select PROG function key
Select Item 2 – System
Selec t Item 3 – Timing options
S elect Item 1 – AC Low Delay and toggle to select 16-hour delay
2. Connect Z e ta Alarm S yst ems’ UL listed and compatible ZNDC dialer as shown in Appendix F.
5.4 Special Output Group Operation
Output Group 91 is th e Non-Reporting group. When using an ZNDC to communicate with a Central Station, points assigned to this gr oup w ill not be reported to the Central Station if an ala rm or
trouble occurs.
Output Groups 92 - 95 are S c hedule groups. Any outputs in these groups will turn on and off
based on the associated output schedule. See section 4 .2.2.2 for schedule programming.
Output Group 96 is the Waterflow group. Monitor Modules selected for Waterflow service should
be placed in this group by du r i ng p rogr amming.
Output Group 97 is for Supervisory Service. Points selected for supervisory operation should be
placed in this group d uring auto programming.
Output Group 98 is the General System Troubl e Group. The System Trouble Relay is placed here
by default.
Output Group 99 is the General Alarm Group. All alarm inputs and all outputs not selected for
other service are place d here by default during auto programming.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 66
5.4.1 Waterflow Point Programming
Any switch monitor module point on the SLC or any conventional input point on the serial bus may
be programmed for the waterflow function . The panel allows for the waterflow alarm to be silenceable if required by the local authority having jurisdiction.
PLEASE NOTE
: NFPA 72 requires waterflow zone alarms be non-silenceable and sound a continuous output alarm. For Central Station monitored systems, no more than five waterflow devices
maybe utilized on a single switch monitor module in the Class A configuration.
To program an input point for waterflow alarm operation, follow these steps
:
1. Install monitor module and connect (See Section 2, Figure W-6 for connection).
2. module SLC address.
3. Select PROG from the me nu (enter access privilege code if necessary).
4. Select 6. Points from the main programming menu.
5. Select 5. Auto-Program. Wait while the panel loads the “new” device information.
6. To access the monitor device you wish to use for the waterflow device:
Select 1. Point, then enter the loop. Press ENTER, enter the device address, then ENTER
again.
7. Select 2. Edit
8. Select 4. Opt ions.
9. Press 1. Type until “Waterflow” is displayed, Press ENTER
10. Press 2. Label to edit the 40-character, alphanumeric label.
To assoc iate the address with Output Group 96 which is not silenceable
:
1. From the Point Edit menu, Select 3. Groups and enter Group 96.
2. Press Enter to store the new settings
3. Press RESET to update the SLC loop flags.
Review all programming selections to insure programming accuracy.
5.4.2 Supervisory Point Programming
Any switch monitor module point on the SLC or any conventional input point on the serial bus may
be programmed for supervisory operation.
PLEASE NO T E
: For NFPA applications, no more than 20 normally open supervisory devices
may be utilized on any zone.
To program an input point for supervisory alarm operation, follow these steps
:
1. Install monitor module and connect (See Section 2, Figure W-6 for connection).
2. Set module SLC address.
3. Select PROG from the me nu (enter access privilege code if necessary).
4. Select 6. Points from the main programming menu.
5. Select 5. Auto-Program. Wait while the panel loads the “new” device information.
6. To access the monitor device you wish to use for the waterflow device:
S elect 1. Point, then enter the loop. Press ENTER, enter the device address, then
ENTER again.
7. Select 2. Edit
8. Select 4. Opt ions.
9. Press 1. Type until “Supervisory” is displayed, Press ENTER
10. Press 2. Label to edit the 40-character, alphanumeric label.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 67
To assoc iate the address with Output Group 97 which does not ring the general alarm :
1. From the Edit menu, Select 3. Groups and enter Group 97.
2. Press Enter to store the new settings
3. Press RESET to update the SLC l oop flags.
Review all programming selections to insure programming accuracy.
5.4.3 Remote Key Reset/Silence
To program an input point for operation as a remote keyed reset or silence station, follow these
steps:
1. Install monitor module and connect (See Section 2, Figure W-6 for connection).
2. Set module SLC address.
3. Install Remote Key Reset Station or Silence Switch as shown in device installation inst ruc-
tions.
4. Select PROG from the me nu (enter access privilege code if necessary).
5. Select 6. Points from the main programming menu.
6. Select 5. Auto-Program. Wait while the panel loads the “new” device information.
7. To acces s the monitor device you wish to use for the Remote Key Reset/Silence function:
S elect 1. Point, then enter the loop. Press ENTER, enter the device address, then ENTER
again.
8. Select 2. Edit
9. Select 4. Opt ions.
10. Press 1. Type until “Rem Silence or Rem Reset” is displayed, Press ENTER
11. Press 2. Label to edit a 40-character, alphanumeric label.
Review all programming selections to insure programming accuracy.
5.4.4 Floor Above/Floor Below
The system can be used up to 90 stories or levels. By simply programming one output group for
each floor and inserting the floor number into the output group characteristics, the panel is programmed to activate the floor(s) above and below the floor in alarm according to the system program Floor Configuration setting. (refer to Section 4.2.2.1 System Options)
For example, assume the panel was set up for “1 Above / 1 Below”, and output group 1 was configured as floor #1, output group 2 was configured as floor #2, and output group 3 was configured as
floor #3. When an input in group #2 goes into alarm, the outputs in group #2 would be activated, as
we ll as the outputs in group #3 (the floor above) and the outputs in group #1 (the f loor below).
To achieve proper operation, the following requirements must be met:
At least one o utput control module or relay must be on each floor, and all notifica ti on appliances on that floor must be controlled by the control module(s) or relay(s) designated for operation on that floor.
Each input point on the same floor must be associated with the output group for that floor.
Review all programming selections to insure programming accuracy.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 68
5.5 Time Control Operations
Time schedule groups ar e groups 92-95, with each group being a ssociated with a different timing
schedule. By placing an outpu t point in output group 92 and setting the associated schedule, the
output point will turn on and off at the times recorded in o u tput schedule 1. Output groups 93-95
provide timing schedules #2, #3, and #4.
To program an output point for use on a Timing Schedule, follow these instructions:
1. Install the ZZRM relay, or supervised output control moduleor I/O relay and connect (See Sec-
tion 2 for connection).
2. Select PROG from the me nu (enter access privilege code if necessary).
3. Select 6. Points from the main programming menu.
4. Select 5. Auto-Program. Wait while the panel loads the “new” device information.
5. Select 1. Point, then enter the loop. Press ENTER, enter the device address, then
ENTER again.
6. Select 2. Edit.
7. Select 3 Groups.
8. Enter Group 92, 93, 94, or 9 5 (Note: If an output is in one of th e on/off schedule groups, it can
be in any number of other groups).
9. Make sure the output schedule has been programmed.
Review all programming selections to insure programming accuracy.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 69
5.6 Program Your Own Applications
1. Desired Results
2. Steps required to Implement
Review all programming selections to insure programming accuracy.
Run Copies to allow you to record application programming.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 71
6. Networking / Serial Devices
The Zeta Alarm Systems Classic 2000 Mk II has t he capability to communicate with up to 127
devices over an RS-485 network. All network devices are 4-wire devices, two wires are required to
provide 24VDC power and 2 for the network communications. Connect the network communication and power wires to the ten-pin connector on the CP3 and any network device, being careful to
observe the “+” and “–” connections.
NOTE: All expansion boards should be attached to the CP3 prior
to mounting the CP3 to the
Power Chassis and assembling in the cabinet. Never Attach Any Accessory Boards To The
CP3 Without First Removing All Power (AC and Batteries). DOING SO WILL VOID
THE WARRANTY.
6.1 Serial Devices
6.1.1 Zeta Remote Display Annunciator (ZRDA)
The Classic 2000 Mk II allows for up to 16 ZRDAs for remote annunciation. The ZRDA will mimic
the Local Display at the main panel and allows Silence and Reset functions.
6.1.2 Conventional Initiating Zone Expansion
The Classic 2000 Mk II can expand its number of Conventional Initiating Zones in three ways:
ZFZA/ZTZB, ZDIO, or Sigma Mk II network through ZPNI b oards.
6.1.2.1 ZFZA/ZTZB
The ZFZA / ZTZB serial expansion cards are compatible with many two-wire fire detectors and any
normally -open contact device. The circuits may also be used as a supervisory circuit to monitor
the normally-open contacts of su pervisory devices, water flow, or pressure switches in sprinkler
systems. The ZFZA / ZTZB operation does not support alarm verification, non-latching alarms, or
normally closed alarms . The ZFZA / ZTZB support ZZRM relay functions (each ZZRM auxiliary
relay is linked auto matically to an individual zone initiating circuit—see section 2.2.6). The Zone
Expansion cards and ZZRM relays can be located in an ZSDE enclosure.
6.1.2.1.1 Zeta Five Zone Class A Expansion Module (ZFZA)
The panel accommodates 12 ZFZA modules (60 Class A / Style 6 zones). Five (5) Class A
zone initiating circuits are provided with the five-zone expansion module. These initiating
circuit s a re power limited and are resettable under microprocessor control. The ZFZA is
able to be located remotely from the main panel via the four-wire ne t work connection.
Each ZFZA will support up to 2 or 4 ZZRMs. See section 6.4.2 for addressing information.
The ZFZA / ZTZB connects to the panel through the RS-485 network.
6.1.2.1.2 Zeta Ten Zone Class B Expansion Module (ZTZB)
The panel accommodates 12 ZTZB modules (120 Class B / Style 4 Zones). Ten (10) Class
B zone initiating circuits are provided with the ten-zone expansion module. These initiating
circuit s a re power limited and are resettable under microprocessor control. The ZTZB is
able to be located remotely from the main panel via the four-wire network connecti on. The
ZTZB will support up to 4 ZZRMs. See section 6.4.2 for addressing information.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 72
6.1.2.2 Dual Input/Output Module
The DIO is a custom module containing two Class B inputs and two Class B / relay outputs. It connects to a Classic 2000 Mk II’s RS-485 network, and runs off an external 24VDC power source.
The two inputs provide a two-wire initiating circuit for normally-open fire alarm and supervisory
dev ices. The two outputs all o w the host panel to switch discrete contacts on command, using one
of two switching modes. The outputs, by default, are configured to switch external DC power or
audio power (selected by removing on-board jumpers) provide one set of Form-C (SPDT) relay
contacts per output. In this mode, t he outputs are n ot supervised.
6.1.2.3 Panel Network Interface (PNI)
The PNI provides a way for a Classic 2000 Mk II FACP to communicate with Sigma Mk II FACPs,
use Sigma Mk II input zones as addressable points, silence and reset a Sigma Mk II from the front
panel of a Classic 2000 Mk II, and view the status of the Sigma Mk II over an RS-232 cable. The
Sigma Mk II must have an ZSCP1 installed. The ZSCP1 provides the RS-232 interface to the PNI,
as well as a lo c a l RS-485 network, which can be used for adding ZFZA, ZTZB, or ZRAN devices.
Pow er comes to the device through one of the Sigma Mk II’s 24VDC outputs. The PNI provides isolation between the Classic 2000 Mk II network and the Sigma Mk II, preventing ground fault troubles on both panels. Using th e PNI, th e Class ic 2000 Mk II can silence and reset the Sigma Mk II
panel, but is not able to control the Sigma Mk II NAC or relay outputs. Standard con f iguration is
one PNI board per Sigma Mk II. The PNI is suitable for mounting in snap-track.
6.1.3 SLC Loop Expansion Using the ZRPC and ZACM
The ZRPC (Zeta Remote Po wer Converter) module will allow the addition of up to two ZACMs
mounted remotely in a Zeta Serial Device Enclosure (ZSDE), see Section 6.7 and ZRPC installation instruction s for more information. Each ZACM provide s for two Sty le 4, 6, or 7 SLC loops.
The ZRPC provides the network and power connection and mounts in the ZSDE. (See the installation instructions inc luded with the ZRPC and ZACM.)
6.1.4 ZRLD Remote LED Driver
The ZRLD (Zeta Remote LED driver Annunciator) is a serial device with the following capabilities:
Displays the status of up to 60 points or groups.
Sounder mimics the operation of the Classic 2000 Mk II main panel buzzer.
Ability to reset the system from the ZRLD ke ysw itch.
Ability to silence the ZRLD, as well as all devices on the system, from the keyswitch.
Each Classic 2000 Mk II will support up to 16 ZRLDs (subject to power availabl e). Each ZRLD
features a DIP switch to program the ZRLD network address and options.
Ability to program 30 Groups on the ZRLD (1-30), and 30 more on the ZRLD-EX (31-60).
The Classic 2000 Mk II FACP can drive remote LEDs for system status annunication, or for building mapping applications. Remote LEDs can be driven by up to sixteen ZRLDs (each of which can
handle up to 60 LEDs).
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 73
Remote LEDs can be configured to annunicate the following:
Global System Info
AC Power OK - This remote LED will be turned on when AC power is present. It is hardmapped to LED #1.
AC Power Fail - This remote LED will be turned on when AC power is absent. It is hardmapped to LED #2.
Offline - This r emote LED will be turned on when the panel is offline. It is hard-mapped to
LED #3.
Input Point Annunication
Each input poi nt may be mapped to two remote LEDs, each of whi ch m ay ann un c ia te ei ther an
alarm or trouble condition. The L ED assignm ents are made in the Point Configuration menu.
Output Group An nunciation
Each output group may be mapped to two remote LEDs. The first LED annunciates the state of the
inputs assigned to the group, while the second LED annunciates the s t ate of the outputs assigned
to the group. Normally, these two LEDs come on at the same time; the only situation in which they
will not is when the panel uses the floor-above/floor-below capability of the panel, in which case a
group's outputs may be activated regardless of whether or not the group's inputs are activated.
The LED assignments are made in the Configure Grou ps menu.
Each driver has a “base LED number”, which is set during system configuration. This number sets
the firs t LE D (or relay) number tha t will be annunciated from that device. For example, if an ZRLD
has a base LED number of “1”, it will be able to annuciate LEDs 1-30 (or 1-60 if an ZRLD expander
is installed). If more than one driver has the same base LED number, they will display identical
information.
Note: The “special” output groups m ay be used to annunciate system-wide conditions:
Output Group 99 = General Alar m
Output Group 98 = General Trouble
Output Group 97 = General Supervisory
Output Group 96 = General Waterflow
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 74
6.1.5 ZCBM City Box/Reversing Polarity Module
The ZCBM (City Box Module) is a serial device and operates in two
modes – supervising a .250 Amp coil, or as a reversing polarity circuit. The system allows for up to 2 ZCBM modules to be connected
simultaneously, ZCBM #1 for alarm, and ZCBM #2 for waterflow
alarms. Two CBMs m ay be connected to two different outputs. It is
activated via the network interface, and has a fixed address system
address (no address programming required) and features the following capabilities:
Supervises coil and activates an approved City Box.
Reports ala rm and trouble via a reversing polarit y connection
(+24VDC, Normal; 0VDC, Trouble; -24VDC, Alarm). The reversing polarity circuit mode activates on General Alarm Group 99
(forZ CBM #1).
Provides Switch for manual disconnect during testing or service
Provides for silenceability and resound on subsequent alarms
Allows for 2 CBM modules to be connected
A 2-position DIP switch is provided on the ZCBM to allow selection
of the operational modes of the module. The #1 switch selects operation as a general alarm (Off) or waterflow alarm (On). Waterflow
alarm operation is not silenceable, ge neral alar m features silence
with resound operation.
The #2 Switch selects the connec tion to a reversing polarity connection (Off) or a city ti e box (On).
Please refer to the installation instructions included with the device.
6.1.6 Zeta Networked Digital Communicator (ZNDC)
The Networked Digital Communicator (ZNDC) is a UL listed dual-line dialer, that allows a Zeta
Alarm Systems Sigma Mk II or Cla ssic 2000 Mk II fire alarm control p anel to re port events to a
central monitoring station, over the public phone system. The ZNDC suppor ts the industr y-standard Ademco Contact ID protocol for reporting the type and location of events. The ZNDC requires
the use of two phone lines. It is a resident o f the RS-485 network, and therefor e can be mounted
remotely. However, Zeta Alarm Systems require that the ZNDC be mounted inside one of our UL
listed enclosures, and be powered from an IPB-3 (Inline Power Booster), Sigma Mk II or Classic
2000 Mk II continuous 24VDC output. The ZNDC is compatible with several UL listed receivers,
including Sur-Gard, Ademco, FBI, Radionics, and Hoffman Osborne. This device also meets FCC
standards. Refer to the ZNDC Operation Manual for more information.
Figure W-13
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 75
6.2
Serial Device Configuration
Configuring the networ k on t he Classic 2000 Mk II requires only t hree steps:
1. Connect all of the devices.
2. Set Network Devices Addresses. (See the installation instructions for each device for assis-
tance in setting the address.) Be careful to give each module an individual address (refer to
device documentation for addressing details). Please refer t o the device installation instructions for hookup, DIP Switch Configuration, and device specifications.
3. Scan the Network. Place the panel into the programming mode, then select option 3 - Net-
work. Select 1. Scan Network. The Classic 2000 Mk II will begin immediately begin to search
for serial devices on the netwo r k. B y monitoring the addresses as they are tested, yo u can verify that the devices on th e network are properly c onnected and functioning. If a device at a particular address is not de tected, check the connections and try again.
4. Review Network Devices. Gives more infor mation and troubleshooting data. In particular, the
“Status” line will show “OK” if communication is working properly, “Comm Error” if the commu-
nication is marginal, and “Comm Trouble” if communication has failed. Of cour se, this informa-
tion is only available after a device has been initially detected,
5. To check the Error Count, go to Netwo rk in the Program menu and Browse the Devices. Once
in the Browse screen, press the “0” key, and an error count will appear on the third line.
6.3 Supervision
The network is supervised by the Classic 2000 Mk II. If any device stops communicating the Mk II
will indicate a network commu nication trouble. The Mk II will rec o r d all network tr ouble or fault
events and restorals in the event log.
Address Range:
Number of
Addresses Device TypeFrom To
0 9 10 Reserved
10 10 1 ZNDC
11 12 2 ZCBM
13 15 3 Reserved
16 31 16 ZRAN / ZRLD
32 47 16 ZRDA
48 59 12 ZFZA / ZTZB
60 63 4 Reserved
64 69 6 ZACM
70 79 10 Future
80 111 32 PNI
112 127 16 Future
128 191 64 DIO
192 250 69 Future
251 255 5 Reserved
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 76
6.4 Addressing Serial Devices
This section describes the relationship of network addresses to programmable point addresses
and instructions for setting addresses.
Each serial device must have a unique network address. For simplicity, we have established point
address ranges that are fixed to each network address. Point address ranges associated with each
network address are shown in the following table:
Relationship of Network Address to Point Range
6.4.1 ZACM Addressing
Each ZACM, except the ZACM on the CP3 board, contains a position DIP switch for network
addressing purposes. The system fixes the ZACM addresses a s follows:
64 = No Switch “On board” ZACM
65 = # 1 On # 2 Off
66 = # 1 Off # 2 On
67 = # 1 On # 2 On
*Special order – see Appendix A for part numbers.
Network
Address
ZFZA/ZTZB
Number
ZTZB Point
Addresses
Point Addresses
(ZFZA) (Empty)
48 1 1 - 10 1 - 5 6 - 10
49 2 11 - 20 11 - 15 16 - 20
50 3 21 - 30 21 - 25 26 - 30
51 4 31 - 40 31 - 35 36 - 40
52 5 41 - 50 41 - 45 46 - 50
53 6 51 - 60 51 - 55 56 - 60
54 7 61 - 70 61 - 65 66 - 70
55 8 71 - 80 71 - 75 76 - 80
56 9 81 - 90 81 - 85 86 - 90
57 10 91 - 100 91 - 95 96 - 100
58 11 101 - 110 101 - 105 106 - 110
59 12 111 - 120 111 - 115 116 - 120
Network
Address
ZACM
Number
Associated
SLC
Point Addresses
(1,3,5,7) AC (2,4,6,8) BD
64 1 1 & 2 1-126 1-126
65 2 3 & 4 1-126 1-126
66 3 5 & 6 1-126 1-126
67 4 7 & 8 1-126 1-126
68* 5 A & B (10 & 11) 1-126 1-126
69* 6 C & D (12 & 13) 1-126 1-126
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 77
6.4.2 ZTZB/ZFZA DIP Switch C onf igu ra tio n
The eight DIP switch posit ions are assigned as follows:
The address bits are only checked when the unit is powering up. If the address needs to be
changed, power needs to be cycled and the network will need to be rescanned. (ZFZA / ZTZB
firmware v1.40 and later allow the address to be changed on the fly, without cycling power.)
There may be up to 16 ZFZAs or ZT ZBs on the network. The addresses range from 48-63, like so:
Network Address 48 = xxx10000
Network Address 49 = xxx11000
Network Address 50 = xxx10100
Network Address 51 = xxx11100
Network Address 52 = xxx10010
Network Address 53 = xxx11010
Network Address 54 = xxx10110
Network Address 55 = xxx11110
Network Address 56 = xxx10001
Network Address 57 = xxx11001
Network Address 58 = xxx10101
Network Address 59 = xxx11101
ZZRM relays attached to ZFZAs or ZTZBs follow the inputs and are not programmable.
Bit
Number
Description “OFF” “ON”
1 ZZRM(s) Installed No ZZRM(s) Installed ZZRM(s) Installed
2 Relays – Per – Zone One Relay – Per – Zone Two Relays – Per – Zone
3 ZFZA Address ( ZT ZB = Don ’t Care) ZFZA #1 ZFZA #2
4Sigma Mk II or Classic Mk II
Addressing
Sigma Mk II Addressing Classic Mk IIAddressing
5 See Device Addressing Info Below 0 1
6 See Device Addressing Info Below 0 1
7 See Device Addressing Info Below 0 1
8 See Device Addressing Info Below 0 1
Unit Bit 1 = 0; Bit 2 = X Bit 1 = 1; Bit 2 = 0 Bit 1 = 1; Bit 2 = 1
ZFZA 0 ZZRMs 1 ZZR M 2 ZZ RMs
ZTZB 0 ZZRMs 2 ZZRMs 4 ZZRMs
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 78
6.4.3 ZRLD DIP Switch Co nf igu ra tio n
The eight DIP switch positions are assigned as follows:
6.4.4 ZRDA Addressing
The ZRDA u se s s eri al EEPROM for addressing . Approximately 15 seconds after applying power,
the ZRDA will annunciate a communication fail trouble. Pressing any button on the screen will ask
you to provide a network address from those available. The availab l e address range for ZRDAs is
32-47. Select your address by pushing Prev/Next button until the one you want is shown. You must
then rescan the network.
To scan the loop, follow these instructions:
Select (1) for PROG
Select (3) for Network
Select (1) for Scan Network
The trouble will clear and your ZRDA will now be functioning normally. If the ZRDA address needs
to be changed, remove the network connection, wait for a “Com m Trouble”, and change the
address.
Bit
Number
Description “ON” “OFF”
1 Network Address, Bit 0 1 0
2 Network Address, Bit 1 1 0
3 Network Address, Bit 2 1 0
4 Network Address, Bit 3 1 0
5 Local Silence Enable Allow the “Silence” switc h
input to silence the ZRLD.
Don’t allow the “Silence”
switch input to silence the
ZRLD.
6 Global Silence Enable Allow the “Silence” switc h
input to silence all devices on
the network.
Don’t allow the “Silence”
switch input to s ilence all
devices on the network.
7 Drill Test Function 1 0
8 Reset Enable Allow the “Reset” switch input
to reset the ZRLD and network.
Don’t allo w the “Reset” switch
input to reset the ZRLD and
network.
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 79
6.4.5 ZRLD Network Addresses
The network address is based on the se tting of bits 1-4 of the DIP switch:
6.4.6 ZCBM Network Addresses
The Classic 2000 Mk II allows for 2 ZCBMs to be installed on the network and two fixed addresses
(11 and 12) are available. The ad dres ses are fixed by selecting the operating mode.
DIP SWITCH BIT DEFINITIONS
Bit 1: Off = ZCBM #1 (Network Address 11) – General Alar m
On = ZCBM #2 (Network Ad dres s 12) – Waterflow Alarm
Bit 2: Off = Polarity-Reversing
On = City Tie Box
Address DIP Switch Setting Address DIP Switch Setting Address DIP Switch Setting
16 22 28
17 23 29
18 24 30
19 25 31
20 26
21 27
1 2345678
ON
1 2345678
ON
1 2345678
ON
1 2345678
ON
1 2345678
ON
1 2345678
ON
1 2345678
ON
1 2345678
ON
1 2345678
ON
1 2345678
ON
1 2345678
ON
1 2345678
ON
1 2345678
ON
1 2345678
ON
1 2345678
ON
1 2345678
ON
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 80
6.4.7 ZPNI DIP Switch Con figu ra tio n
The ZPNI may be addressed to one of 32 network addresses. Use the DIP switch on the board to
set the address.
*Global Silence and Reset apply only to th e ZPNI-DRV. See Z P NI prod u ct documentaion for explanation
and application.
6.5 Serial Device Technical Specifications
6.5.1 ZTZB/ZFZA Specifications
Bit
Number
Description
0 Network Address Bit 0
1 Network Address Bit 1
2 Network Address Bit 2
3 Network Address Bit 3
4 Network Address Bit 4
5
6 Global Silence*
7 Global Reset*
POWER REQUIREMENT
To be connected to a UL listed Power Limited
Class II or Class III source of supply only
Input Voltage Minimum 22VDC
Nominal 24V DC
Maximum 25.5VDC
Normal Mode (Standby) ZTZB 65mA
ZZRM 1.5mA
10% Alarm Condition ZTZB (1 zone) 110mA
ZZRM (1 zone) 18mA
Each zone in alarm adds … 45mA
Each ZZRM relay on adds … 16mA
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 81
Each circuit employs transient voltage protection, is power-limited, and supervised.
6.5.2 Power Requ ir ement - ZRDA
Power Requirement: To be connected to a UL listed Power Limited Class II or Class III source of
supply only.
6.5.3 Power Requ ir ement - ZRLD
SPECIFICATIONS
All circuits are Power Limited
Loop Voltage Max 30VDC
Nominal 24V DC
Loop Short Circuit Current Nominal 40mA
Max 45mA
Supervision Current 5Ma
End-Of-Line Resistor (PN 900) 4.7K Ohms
Maximum Line Resistance Per Side 25 Ohms
Maximum Total Line Resistance Per Zone 50 Ohms
Input Voltage Nominal 24 VDC
Maximum 30 VDC
Current Standby 40 mA
Alarm 60 mA
POWER REQUIREMENT
To be connected to a UL listed Power Limited
Class II or Class III source of supply only
Input Voltage Minimum 12VDC
Nominal 24V DC
Maximum 30VDC
Normal Mode (Standby) ZRLD 40mA
ZRLD 40mA
10% Alarm Condition ZRLD(5LED on) 110mA
ZRLD(5LED on) 110mA
Each LED on adds 14mA
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 82
6.5.4 Power Requ ir ement - ZPNI
6.6 Wiring Block Diagrams
6.6.1 Wiring Block for ZFZA/ZTZB, ZRLD Network Devices
Figure W-15
NOTE: The Classic 2000 Mk II provides for a shielded communication connection. The
shield or drain wire at the ZTZB/ZFZA or ZRLD should be connected to the enclosure.
Please refer to installation instructions for connection information.
POWER REQUIREMENT
To be connected to a UL listed Power Limited
Class II or Class III source of supply only
Input Voltage Minimum 2 2VD C
Nominal 24VDC
Maximum 25.5VDC
Normal Mode (Standby) ZPNI-SK1 30mA
Operation (Alarm, Printing,
Network Communications, etc.)
ZPNI-SK1 30mA
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 83
6.6.2 Wiring Block for ZRPC, ZCBM, ZRDA Network Devices
Figure W-16
6.6.3 Wiring Block for ZDIO Network Devices
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 84
6.7 Serial Device Enclosure Installation Procedures
6.7.1 Serial Device Enclosure Installation
Refer to the Serial Device for complete Installation Instructions
6.7.2 Single Device Installation
The following hardware is required for installing a single device:
Four ½" nylon snap-in stand-offs
One ZFZA/ZTZB/ZRPC
Install the four ½" nylon snap-in stand-offs by screwing them onto the four studs in the upper portion of the cabinet. Refer to the ZSDE enclosure dra wing for mounting location. Attach the ZFZA/
ZTZB or ZRPC into the cabinet by pressing the unit onto the snap-in stand-offs.
6.7.2.1 Dual Device Installation
The following hardware is required for installing multiple devices:
Four ½" nylon M/F stand-offs
Four 1" nylon snap-in stand-offs
Two ZFZA/ZTZB
Install the four ½" nylon M/F stand-offs by screwing them onto the four studs in the upper portion of
the cabinet. Refer to the following figure for mounting location. Attach the first ZFZA/ZTZB into the
cabinet by placing it over the M/F stand-offs and securing it by screwing the 1" nylon snap-in
stand-offs onto the M\F stand-offs. Attach the second ZFZA/ZTZB by pressing the unit onto the
snap-in stand-offs.
6.7.3 Installation of ZACMs
Install the first ZACM onto the ZRPC u sing t he hardware provided and following the instructions
provided with the ZRPC.
6.7.3.1 Adding a Second ZACM
Install the second ZACM onto the top of the first ZACM using the hardware provided and following
the instructions provided with t he ZRP C. Note: Make sure pins are lined up when boards are
stacked and power is off.
Figure W-17
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 85
Appendix A:
Classic 2000 Mk II Part Number/OrderingInfo
6 Amp Power Supply
ST P/N Description
3000-6806 Panel w/Programming Display, 2 SLC Loops, 4 Output Circuits, 110/220V
8 Amp Power Supply
ST P/N Description
3000-6808 Panel w/Programming Display, 2 SLC Loops, 4 Output Circuits, 110/220V
Assemblies/Modules
ST P/N MDL# Description
3000-6200 CP3/LPD Central Processing Unit w/Local Programming Display (3000-CP3)
3000-6855 ZACM-A Addressable Communications Module-Apollo
3000-6856 ZACM Special order ZACM—Board #5
3000-6857 ZACM Special order ZACM—Board #6
3000-6060 ZRPC Remote Power Converter
3000-6006 ZRDA Remote Display Annunciator
3000-6825 Z C BM City Tie Box Interface Module w ith mounting hardware
3000-6835 ZS CP-3 Serial Communication Interface Module with mounting hardware
3000-6830 ZICP Isolated Communication Port with mounting hardware
2936 ZTZB 10-Zone Class B Initiating Circuit Expander
2941 ZFZA 5-Zone Class A Initiating Circuit Expander
2918 ZZRM5 5 Zone Relay Expansion Module with mounting hardware
2980 ZIPB-3-1 Stand Alone Auxiliary 3 amp Power Supply, 110V
2981 ZIPB-3-2 Stand Alone Auxiliary 3 amp Power Supply, 220V
2990 ZNDC Networked Digital Communicator
905A EOL-10K 10K Ohm End Of Line Device
900A EOL-4.7K 4.7K Ohm End Of Line Device
4035 ZRLD 10-Zone Rem ote LED Driver
4040 ZR LD-EX 10-Zone Remote LED Expansion Driver
4012 ZSDE Enclosure for Serial Devices (ZRPC, ZACM, ZFZA, ZTZB)
3000-6615 ZBCA Battery Enclos ure – up to 55 AH (required for larger than 17AH batteries)
3000-6865 ZDIO Dual Input / Output Module
3000-6850 ZPNI-S1K Panel Network I nterface – Sigma Mk II Interface
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 86
Appendix B:
Classic 2000 Mk II Battery Backup Calculation
SYSTEM COMPONENTS
Quantity
Stand-By
Current
(mA)
Maximum
Alarm
Current
(mA)
Total
Stand-By
Current
(mA)
Total
Alarm
Current
3000-6400 Syste m Board (CP3, LPD, PSC, 1 ZACM) 0 155 165 0 0
3000-6855 Addressable Communication Module (ZACM) 0 30 30 0 0
2918 Zone Relay Module (ZZRM) 0 1 75 0 0
SERIAL DEVICES
3000-6825 City Box Module (ZCBM) 0 45 60 0 0
2996 Networked Digital Communicator (ZNDC) 0 56 76 0 0
3000-6807 Remote Display Annunciator (ZRDA) 0 45 60 0 0
4010 Remote Annunciator (ZRAN) 0 40 420 0 0
4025 Remote Annunciator Expander (ZRAN-EX) 0 0 420 0 0
4035 Remote LED Driver (ZRLD) 0 40 420 0 0
4040 Remote LED Driver Expander (ZRL D-EX) 0 0 420 0 0
3000-6860 Remote Power Converter (ZRPC)
1
05050 0 0
2936 Ten Zone Class B (ZTZB) 0 65 515 0 0
2941 Five Zone Class A (ZFZA) 0 90 270 0 0
DETECTORS / MODULES
55000-550 ISH-550 Ion Sensor Head 0 .28 2 0 0
55000-650 PSH-650 Photoelectric Sensor Head 0 .34 4 0 0
55000-450 TSH-450 Temperature Sensor Head 0 .25 4 0 0
55000-750 IMB-750 Isolator Module 0 .12 8 0 0
55000-830 MPM-830 Mini Priority Switch Monitor Module 0 .6 4 0 0
55000-806 PMM-806 Priority Switch Monitor Module 0 .6 4 0 0
55000-820 SMIO-820 Switch Monitor Input-Output Module 0 .85 4 0 0
55000-825 SCM-825 Sounder Control Module 0 1 4 0 0
Number of SLC Loops in System
2
00.8000
NOTIFICATION APPLIANCES
Other - NAC #1, 2.75 Amps Maximum 0 0 0 0 0
GMS24 - 15/75WR 0 0 139 0 0
GEC24 - 15/75WR 0 0 142 0 0
Other - NAC #2, 2.75 Amps Maximum 0 0 0 0 0
GMS24-15/75WR 0 0 139 0 0
GEC24-15/75WR 0 0 142 0 0
Other - NAC #3, 2.75 Amps Maximum 0 0 0 0 0
GMS24-15/75WR 0 0 139 0 0
GEC24-15/75WR 0 0 142 0 0
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 87
NOTES:
1. Required for remote ZACMs
2. SLC Loops are Current Limited at 80mA in alarm. This requirement is included on the last line of the Detectors/
Modules section of this chart.
3. Review the top lin e for t he indication of st andby and alarm curr ent
4. Current values are in mAmps unless otherwise specified.
Other - NAC #4, 2.75 Amps Maximum 0 0 0 0 0
GMS24-15/75WR 0 0 139 0 0
GEC24-15/75WR 0 0 142 0 0
TOTAL STANDBY CURRENT - mA
0
TOTAL ALARM CURRENT - mA
0
TOTALS
A) Supervisory (standby) Current - mA (Item 35, above) 0
B) Supervisory Time in Hours (24 or 60) 24
C) Supervisory Requirements (A x B) 0
D) Power Supply Size (Enter .00575 or .0075) or Alarm Curr ent (I tem 36, above) 0
E) Alarm Time in Minutes (For 5mins enter .0833; for 10mins enter .167) 0
F) Alarm Requirement (D x E) 0
G) Battery Backup Requirement (C + F) 0
H) 20% Safety Factor (G x .2) 0
I) Battery Requirement w/ 20% Safety Factor (G + H) 0
J) Required Battery Size in Amps. 0
SYSTEM COMPONENTS
Quantity
Stand-By
Current
(mA)
Maximum
Alarm
Current
(mA)
Total
Stand-By
Current
(mA)
Total
Alarm
Current
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 88
Appendix C-1:
24VDC Notification Circuit Compatible Devices
Gentex Models
Horn and Horn/Strobes: (21-30 VDC) AVS44, AVP-4, HS24, HG124, SHG24, GEH24, GES24-15,
GES24-15/75, GES24-30, GES24-60, GES24-75, GES24-110,
GEC24-15, GEC24-15/75, GEC24-30, GE24-60, GEC24-75,
GEC24-110, GMH24,GMS24, G EC, GES, G X90-4, GX90S-4, G X S4 ,
ST24, WGMS-24, ZMS4
Speaker/Strobes: (18-30 VDC) SPK4, SPK424, SPK424, SPK8, SPK824
Amseco 24VD C Mo dels
Bells: BZ-54, EXB6 to 10-A4, EXB6 to 10-PV4, HP-24, MB-G6-10, MSB- 63/S L,
MSB-64V
Strobes: SL-1, SL- 3 , SL-5
Faraday (FOS) 24VDC Models
Horns and Horn/Strobes: 5306-5308, 5326-5328, 5336-5338, 5346-5348,61 26-6128, 6146-6148,
5510, 5508, 5521, 552 2, 6166-6168 LU or O-14-24-DC
Speaker/Strobes: 2606-2608L-U-4-25V and L-U-4-70V
Wheelock 24V Models
Chimes and Chime/Strobes: CH-F1-WM
Horns and Horn/Strobes: MT-24, MIZ-24-WH or WM
Speaker/Strobes: E-1010-WH or WM, E-7025-WH or WM, E -7070-WH or WM, E-7025,
E-9025-WH or WM, E-7070, E-9025, E-9070, ET-1010, ET-1070,
ET-1070-WM, ET1080, ET1080-W M, ET-1090
Strobes: WMT, WM1T, WM3T
Vibrating Bells: 42PT-G, 43T-G, 43T-G10, 46T-G10, 46T-G4
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 89
Appendix C-2:
Two-wire ZTZB/ZFZA Detector Compatibility
Smoke Detector Series Detector Models Identifier Max. per circuit
Zeta Alarm Systems
Detector Head SIH-F, SLK-F, SLK-FH ST40 40
For use with these bases HS-D, YBA-M ST04 NA
HS-RB ST05 NA
Apollo
Detector Heads 55000-150,151,152,153 55000-150,151,152,153 31
55000-250 55000-250 30
55000-350 55000-350 16
55000-380 55000-380 9
For use with these bases 45681-200,220,232 45681-200,220,232 NA
Detector Heads 55000-150,151,152,153 55000-150,151,152,153 20
55000-250 55000-250 22
55000-350 55000-350 13
55000-380 55000-380 8
For use with this base 45681-227,230,231 45681-227,230,231 NA
Hochiki
Detector Head DCD-135, DCD-190, SIJ- 24, HD-3 40
SLR-24, SLR-24H, SLR-835
For use with these bases HSC-221R HB-71 NA
NS4-100, NS6-10 0 HB-55 NA
NS4-221, NS6-22 1 HB-4 NA
Detector Head (baseless) SLR-835 B-2 HD-6 40
Fenwal
Detector Head 7051 151FE1 30
7155 P55FE1 25
7156 P56FE1 25
For use with these bases 2WRB, 2WRLT FE51A NA
Duct Detectors DH-60(7051D) FE51A 30
Duct Detectors DH-60(7155D) FE51A 25
Sentrol
Direct Wire (baseless) 429C, 429CT S10A 40
Direct Wire (baseless) 521B, 521BXT (sw 1 off) S10A 40
Detector Head 711U, 7 11UT, 712U, 713-5U, 713-
6U, 721U, 721UD, 721UT, 722R U
S10A 40
For use with these bases 701E, 701U, 702E, 702U, 702RE,
702RU
S00 NA
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 90
Appendix C-3:
Compatible SLC Devices and Accessories
Part Number Description
55000-550 Ion Sensor Head
55000-650 Photo Sensor Head
55000-450 Temperature Sensor Head
55000-750 Isolator Module
45681-211 Isolator Base
45681-234 Low-profile Base, 6"
MB-RLY-XP95A Base with Relay, 4-wire
MB-SDR-XP95A Base with Sounder, 4-wire
45681-771 Xpert Address Programming Card
55000-830 Mini Priority Monitor Module
55000-806 Pr ior ity Monitor M odu le
55000-825 Sounder Control Module
55000-820 Mon itor Input / Output Module
RW -AA- N Duct Housing w/ Ionization Sensor Head, Exhaust Tube
RW-AA-P Duct Housing w/ Photoelectric Sensor Head, Exhau st Tube
RW-AR-N Duct Housing w/ Ionization Head, Exhaust Tube, Form C Relay
RW -AR-P Duct Housing w/ Photoelectric Head, Exhaust Tube, Form C Relay
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 91
Appendix D:
Classic 2000 Mk II OPERATING INSTRUCTIONS
CLASSIC 2000 Mk II BASIC OPERATING INSTRUCTIONS
This Instruction Sheet should be framed and placed adjacent to the control unit for easy reference.
Display - Th e 80 -charact er LCD screen displays a ll messa ge s an d in for m ation about the syst em . It is also used t o dis play program
menus, the time and date, and company name.
LED Indicators - The system condition LED indicators are provided to indicate System Alarm, Trouble, Supe rvisory conditions, and
Alarm, Trouble, and Supervisory Silenced co nditions. Other LEDs indicate the status of A C Power, and Offline (other than normal)
Mode, and Test Mode .
Panel Control Keys - Below th e LCD scr ee n , the pa ne l co nt ro l keys SILENCE and RESET are foun d. T h es e keys al low yo u to
silenc e al arms an d troubles and res et any off- n ormal co nd ition. Pres si ng the SILENCE key will silen ce the panel sounde r and external not ifi cat i on ap pli an ces , and the corr esp on di ng Silen ce d LED wil l illu mi na te and flas h unti l th e panel is reset or unti l another alarm
is sensed. A second alarm condition will cause all previously silenced alarm conditions and the panel sounder to resound its audible
tone.
Pressing the RESET key will return the panel to normal operating mode, clear any o ff -normal condition from the status display;
restore the alarm relay to normal state; extinguish all status LEDs except the green AC LED; and send a message to the display and
printer (if applicable) that a System Reset has been performed.
To the right of the L CD sc re en are two panel co ntrol keys labele d NEXT and PREV. These two keys allow you to view more menu
opti ons when av ailable . These t wo keys also advance to the next character or number when entering individual information into the
panel.
Function Keys - The Function Keys are found below the SILENCE and RESET keys. The first five keys disp lay menus that control
the panel, its pr ogr am ming, and any other function needed for the syst em operation (PROG, STA TUS, TEST, PRINT, DRILL). Sec-
ond, these keys serve as a numeric and alphabetic keypad used during menu options.
The ESCAPE and ENTER pane l co ntr ol keys are found to th e r ig h t of the fun c t io n keys. The ESCAPE key allows you to exit any
menu at any time without saving the information to the panel’s memory and automatically moves to the previous screen. The ENTER
key stores the programming selection i nto the panel’s memory and automatically moves to the next option screen.
Operation Keystrokes
Silence alarms and troubles Press the “SILENCE” key
Reset Alarms Press “RESET” key
View Alarm and Troubl e Co nd itions System w i ll au tom atically sc ro ll through events at 3-second intervals, also show-
ing the event summary.
View Status of a point 1. Pre ss STATUS key
2. Select 2. Device Status
3. Brows e devices by us ing :
6 & 7 keys to scroll through loops
NEXT and PREV to sc r ol l thr o ug h po ints
0 key to view ALL points, or INSTALLED points only
Enable/D is a ble a poi nt or loop 1. Press PRO G key
2. Enter point loo p:add re ss
3. Select EDIT
4. Toggle from On to Off by pressing 1
View Event History 1. Pres s STATUS key
2. Press 1. Event History
3. Select Browse
Scroll events using PREV/NEXT keys
Set Time & Date 1. Press the PROG key
2. Select 1. Clock
Time - Edit in Pl ace - XX:XX:XX
Date - Edit in Place - XX/XX/XXXX
Time Mode - Toggle 12hr/24hr
Fire Drill 1. Press the DRILL key
2. Enter Access Pri vi lege Co de (APC)
3. Press any key to end drill
In the Event of Trouble, Please Contact: _____________________________________
_____________________________________
_____________________________________
Periodic testing of this System Is recommende d no less than annually
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 92
Appendix E: Classic 2000 Programming Menus
Menu Description Default Setting Access
Level
Required
Main Screen 0
Reset (resets the panel)
Active Event Screen 0
Reset (resets the panel)
Silence (silences any active events)
Program 0
1. Clock Default = 00:00:00
1. Time Default = 01/01/1998
2. Date Default = 12-Hour Mode
3. Time Mode
2. System 2
1. Options
1. LatchTroubles Default = No (Non-Latching)
2. TroubleRemind Default = No (trouble reminder disabled)
3. WaterflowSil Default = No (waterflow not silenceable)
4. Printer Def ault = Disabled
5. FloorConfig Default = 1A/1B
2. Timing
1. AC Low Delay Default = 0h
2. Auto Silence Default = 0m (i.e. disabled)
3. Silence Inhibit Time Default = 0s (i.e. disabled)
4. Alarm Verify Default = 30s
5. Holidays Default = 00/00
6. Schedules
1. Day/Night Sch #1
1. Day Start: Default = 00:00
2. Day End: Default = 00:00
3. Day Sens: Default = Low
4. Night Sens: Default = High
5. Days: MTWTF
2. Day/Night Sch #2
…same as #1…
3. Day/Night Sch #3
…same as #1…
4. Day/Night Sch #4
…same as #1…
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 93
5. On/Off S ch #1
1. On: Off: Default On: 00/00
2. On: Off: Default Off: 00/00
3. On: Off:
6. On/Off S ch #2
…same as #1…
7. On/off Sch #3
…same as #1…
8. On/Off S ch #4
…same as #1…
3. Access Cod es Default = 111111 for level 1
Default = 222222 for level 2
4. Edit Banner Msg Default =
Zeta Alarm Systems Class 2000 Mk II
3. Network
1. Scan
2. Browse Device s
3. Style Default = 4 (Class B)
4. Inputs
1. Options
1. Test Time In 24-hour mode 00:00
2. LED Blink Default = Yes (LED Blink enabled)
2. Sensitivity Levels
1. Ion Sensitivity
1. Low Default = 67
2. Medium Default = 60
3. High Default = 56
2. Photo Sensitivity
1. Low Default = 62
2. Medium Default = 55
3. High Default = 48
3. Heat Setting
1. Low Default = 090
2. Medium Default = 071
3. High Default = 055
3. Alerts
1. Ion Aler ts
Maintenance: Default = 35
Menu Description Default Setting Access
Level
Required
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 94
Service: Default = 40
2. Photo Alerts
Maintenance: Default = 35
Service: Default = 40
5. Outputs
1. Configure NACs
1. NAC1 Default = NAC-ST
2. NAC2 Default = NAC-ST
3. NAC3 Default = NAC-ST
4. NAC4 Default = NAC-ST
2. ZZRMs Installed: Default = 0
6. Points
1. Point Default = 1:001
2. Edit Po int
1. Enabled Default = Enabled
2. Label
3. Mapping
4. Options (Options vary per device)
(Sensor)
1. Alarm Ver: Default = No
2. Sensitivity: Default = High
(Input)
1. Monitor Type
(Output)
1. Silenceable: Default = 0
2. All Call: Default = 0
3. Browse
4. Status Absent
5. Auto Program
1. New Device
1. Yes
2. No
3. Yes to All
4. No to All
2. Missing Device
1. Yes
2. No
3. Yes to All
Menu Description Default Setting Access
Level
Required
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 95
4. No to All
7. Groups
1. Group
2. Browse Groups
3. Edit
1. Enabled Default = Enabled
2. Floor Default = XX
3. Count Default = 1
4. Label
5. LEDs Default = 0000 0000
8. PC Comm unicatio ns
9. Factory Defaults
Reset Panel To Factory Defaults
— Are you sure?
1. Yes
2. No
Status 0
1. Event History
1. Status
2. Browse
3. Filter Default = All events
2. Device Status
3. PSC
4. Versions
Test 1
1. Walk Test
1. Normal Walk Test
2. Silent Walk Test
2. NAC Test
1. NAC #1 Default = Off
2. NAC #2 Default = Off
3. NAC #3 Default = Off
4. NAC #4 Default = Off
3. Relay Test
1. Trouble Default = On
2. Alarm Default = Off
3. ZZRMs Default = Off
4. Display Test
Menu Description Default Setting Access
Level
Required
Zeta Alarm Systems. Classic 2000 Mk II Oper at ion Man u al
Revision 1.0 Part # MAN-Z3K-01 Page 96
Other Information
Access Levels
0 = General Level, no code required (security provided by front panel keylock)
1 = User Level, default code = 111111
2 = Installer Level, default code = 222222
Attempting to use a feature for which you do not have access will pop up a screen.
Entering a correc t code will say “You have been granted access level X” (1 or 2).
Entering an incorrect code will say “Access is denied”.
Access lasts for 10 minutes after last keypress, then returns to “0” silently.
5. CP3 Test
6. Mapping
1. Alarm Default = Off
2. Trouble Default = Off
Print 1
1. Event History
1. All
2. Alarms
3. Troubles
4. Status
2. Programming
1. Concise
2. Verbose
3. Device Status
Drill 1
(Turn on all NACs, press Drill to end.
Panel will reset.)
Menu Description Default Setting Access
Level
Required
Loading...