ZEROtherm BTF80, BTF90 User Manual

USER’S MANUAL

[English]

Please read this USER’S MANUAL carefully before installation

Applicable Models

• ZEROtherm BTF80(100% Aluminum Fin)

• ZEROtherm BTF90(100% Copper Fin)

Specifications

Models

Dimension (L x W x H)

Fin

Material

(W/O Optional Components)

Base

Heat Pipe

Weight

BTF80

108 x 81 x 128 mm

(5.04 x 3.19 x 4.25 inch)

Aluminum

Copper

Copper(Sintered type)

4,404cm

Over 140W Cooling capacity

92 x 25mm (3.62 x 0.98 inch)Fan size

750 ~ 2,500rpm±10%Fan speed

Under 27.0dB±10%Acoustical noise

4-pin(PWM)Connector

12 VDCOperating voltage

Max. 1.54WConsuming power

Max. 42.8CFMAirflow

458g

BTF90

Copper

(682.6inch2)Heat dissipation area

Over 150W

678g

Precaution

• CPU and

• Excessi ve force may result in malfunction or damage to the fan,

• The product is not compatible with a slim body type case.

• APA CK Inc is not responsible for any dam age to the product,

motherboard are subj ect to damage i f the product is

incorrectly installed. Familiarize yourself w ith this “USER’S MANUAL” before installing the product.

the product or the computer. Avoid inserting any objects into the fan while operating.

Please check the compatibility at www.zerotherm.co.kr (or www.apack.net)

and/or the computer including CPU resulted from:

1). Incorrect installation

2). CPU overclocking

Components

① CPU Cooler (front view) ② CPU Cooler (Separated Fan) ③ Intel Clip ④ Back Plate (for Intel) ⑤ Clip Screws (4 pcs, for Intel) ⑥ AMD Clip ⑦ Thermal Grease ⑧ User’s Manual

Heat Pipe

Fin

Fan Rail

Bracket

Installation(Intel–Socket 775) Installation(AMD–Socket 754/939/940/AM2)

• Install Back Plate

1) Remove the

insulating

2) Attach the back plate to the back side of the m ain board with

the socket RM (Retention Mechanism) holes lined up.

• Spread Thermal Grease

1) Clean off particles

2) Spread thermal grease thinl y

• Install Intel Clip

1) Install Intel clip using a screw driver on the bottom of the cooler

[Caution] Excessive force may damage the heat pipes. It is

easy to install the clip after laying the product down sideways like [

• Separate Fan Component

1) In order to install the product on Intel CPU, the fan should be

separated from the unit.

2) Gently grasp the fan rail (Red Bar) and pull it up and out of the

unit.

3) If you use a bar or a driver li ke [

the fan up and out of the unit.

[Caution] Be careful not to damage the fins when you pull

the fan up with a bar or a driver.

• Install Cooler

1) Fasten the screws with a driver and install the cooler on the

CPU.

[Caution] Make sure that there are no interfering

components before installing the cooler.

• Install Fan Component

1) Push the fan down on the bracket rail like [

thin paper film from the back pl ate to expose the

tape. [Picture 4]

or dust from the top of the CPU.

and evenly on top of the CPU

Picture 8].

Picture 9], you can eas ily pull

Picture 10 and 11]

• Spread Thermal Grease

1) Clean off particles

2) Spread thermal grease thinl y

• Install AMD Clip

1) Install AMD clip using a driver on the bottom of the cool er

2) The AMD clip c an be installed horizontally or vertically in accordance with your motherboard’s RM (Retention

Mechanism).

[Caution] Excessive force may damage the heat pipes. It is

easy to install the clip after laying the product down sideways like [

• Install Cooler

1) Fasten the screws with a driver and install the cooler on the

CPU.

[Caution] Make sure that there are no interfering components before installing the cooler

1212

or dust from the top of the CPU.

and evenly on top of the CPU

Picturer 12~ 15]

Horizontal type

1313

BIOS SETUP

Since ZEROtherm CPU coolers feature extreme low fan speed (RPM) while achieving optimal results, it is possible

that you may experience an initial booting error prompting “CPU Fan Error!” This seldom happens since only a few number of mother board brands (includi ng ASUS) report this problem. This “CPU Fan Error!” message has nothing to do with a real system error and can be easily fixed.

When “CPU Fan Error!” prompts, set up the BIOS as

followings:

① Booting Error – CPU Fan

Error

A few number of mother

board brands (including ASUS) may prompt “CPU Fan Error!”

③ Boot Settings Configuration

② BIOS Setup – Boot tap

Press the “DEL” button on the

keyboard to set up the BIOS.

Select “Boot” tap and “Boot Settings Configuration”

④

“Wait For ‘F1’ If Error” Options

Features

Silence Innovations

• Ultra maglev forms oil protecti on bearing technology adapted

• PWM fan speed control (750~2,500rpm)

• Optimized airflow desi gn

Killer Performance

• Efficient 8-line heat pipe effects

•

Polished copper base for better thermal conductivity

• High performance thermal grease adapted(TC-5022)

Creative & Cool Design

• Unique butterfly motif fins

•

Super bright LEDs

Compatibility

• Intel socket 775 up to Core

• AMD socket 754, 939, 940 and AM2

2 Duo

Patents

• Republic of Korea patent application No. : 40-0564565-0000

• Republic of Korea design application No. : 30-2006-21470

• Patent applications pending around the world i ncluding USA, EU,

and Japan

Bracket Rail

0404

Fan

Block

3333

Intel Clip

6666

AMD Clip

1111

CPU Cooler

4444

7777

Thermal Grease

2222

5555

Clip Screw (4pcs)

Back Plate(For Intel)

Remove the thin paperf ilm, and then attach the back side of the main board

0909

Separate the fan from the cooler, and then install cooler from the main board

1010

Fan Rail

Bracket Rail

Install Intel Clip

0808

1111

Install the fan

1414

Vertical type

1515

Waranty & Disclaimer

• Warranty : 2 Years from the purchase date

• APACK INC. is not responsible for any damage due to external causes, including but not limited to, improper use,

problems with electrical power, accident, neglect, alteration, repair, improper installation, or improper testing.

- www.zerotherm.co.kr // www.apack.net

- sales@apack.net

Select “Wait For ‘F1’ If Error”

⑤ W ait For ‘F1’ If Error – Disabled

Now Wait For ‘F1’ If Error options are Disabl ed.

Press the “Enter” button on

keyboard. Change its

the

options into “Disabled”.

⑥ Save configuration changes and exit

Press “F10” button in your keyboard. Select “OK”, when the prompt ask if you want to save configuration changes and exit now.