SGCZ2610DL/SGCZ2610DW
115333510 (001)
OWNER’S MANUAL
RECIPROCATORS
G
G
B
B
SGCZ2610DL
SGCZ2610DW
Original Language
GB-1
SGCZ2610DL/SGCZ2610DW
EC DECLARATION OF CONFORMITY
(Applies to Europe only)
The undersigned manufacturer,
declares under sole responsibility that the following products referred to in this
declaration conform with the requirement of the following COUNCIL’S DIRECTIVE.
The products referred to are :
This declaration conform with :
Date :
Husqvarna Zenoah Co.,Ltd.,
1-9, Minamidai, Kawagoe, Saitama, Japan,
DESIGNATION : RECIPROCATORS
MANUFACTURER : Husqvarna Zenoah Co., Ltd.
MODELS : SGCZ2610DL/SGCZ2610DW
SERIAL NUMBERS DATING : 2010 and onwards
(The year is clearly stated on the rating plate,
followed by the serial number)
・DIRECTIVE 2006/42/EC
(The following standards have been applied: ISO 12100-1,-2, FprEN 15503: 2009)
・DIRECTIVE 2004/108/EC
(The following standards have been applied: EN 61000-6-1, EN 55012 (CISPR 12: 2005))
・DIRECTIVE 2000/14/EC
conformity assessment procedure followed ANNEX V
(The following standards have been applied: ISO 11094)
・DIRECTIVE 2002/88/EC
・ENISO 11806
29 December 2009
Signature :
Kiyoshi Honda
General Manager, Development Center
Authorised representative :
Person authorised to compile the technical file :
Husqvarna AB
SE-561 82 Huskvarna, Sweden
Bo R Jonsson
SE-561 82 Huskvarna, Sweden
EXPLANATION OF SYMBOLS AND SAFETY WARNINGS
WARNING!!!
RISK OF DAMAGING HEARING
Wear head, eye and ear protection.
MODEL
SOUND LEVEL
ISO 22868
LpAeq
SGCZ2610DL 25.4 cm
SGCZ2610DW 25.4 cm
* Specifications are subject to change without notice
1) Noise emissions in the environment measured as sound power (L
Reported soundpower level for the machine has been measured with the original cutting attachment that gives the highest level.
The difference between guaranteed and measured sound power is that the guaranteed sound power also includes
dispersion in the measurement result and the variations between different machines of the same model according to
Directive 2000/14/EC.
Reported data for equivalent sound pressure level (L
dispersion (standard deviation) of 1 dB (A).
2) Reported data for equivalent vibration level (a
tion) of 1 m/s
2
.
3
86 dB(A) 106 dB(A) 4.7 m/s
3
86 dB(A) 106 dB(A) 4.2 m/s
pAeq) at the operator’s ear for the machine has a typical statistical
hv,eq) at the control handle has a typical statistical dispersion (standard devia-
1)
ISO 22868
LwA
guaranteed
WA) in conformity with EC directive 2000/14/EC.
VIBRATION LEVEL
ISO 22867
ahv.eq
2
2
2)
GB-2
APPROVAL NUMBER OF CE EXHAUST EMISSION REGULATION
DIRECTIVE 97/68/EC AMENDED 2002/88/EC
e13*97/68SH2G3*2002/88*0404*00
SGCZ2610DL/SGCZ2610DW
SAFETY FIRST
Instructions contained in warnings within this manual marked
with a
into consideration to prevent possible serious bodily injury, and
for this reason you are requested to read all such instructions
carefully and follow them without fail.
WARNINGS IN THE MANUAL
This mark indicates instructions, which must be followed in order to prevent accidents, which could lead to serious bodily injury or death.
This mark indicates instructions, which must be followed, or it
leads to mechanical failure, breakdown, or damage.
This mark indicates hints or directions useful in the use of the
product.
symbol concern critical points which must be taken
WARNING
IMPORTANT
NOTE
Contents
1. Parts location .................................................. 3
2. Specifications ................................................. 4
3. Warning labels on the machine ...................... 4
4. Symbols on the machine ................................ 4
5. For safe operation ........................................... 5
6. Set up ............................................................. 8
7. Fuel ............................................................... 10
8. Operation ...................................................... 11
9. Maintenance ................................................. 14
10. Storage ......................................................... 16
11. Disposal ........................................................ 16
12. Troubleshooting guide .................................. 17
G
B
1. Parts location
(1) Primer
(2) Air cleaner cover
(3) Choke lever
(4) Fuel tank
(5) Starter knob
(6) Spark arrester
(7) Blade
(8) Angle transmission
(9) Cutting attachment guard
(10) Handle
(11) Shaft tube
(12) Suspension point
(13) Throttle trigger
(14) Stop switch
(15) Throttle cable
(16) Hip pad
2
8
SGCZ2610DL
3
1
5
4
7
6
11
9
8
10
12
14
13
13
11
9
15
14
SGCZ2610DW
12
16
15
10
7
GB-3
SGCZ2610DL/SGCZ2610DW
2. Specification
Model SGCZ2610DL SGCZ2610DW
Overall size (LxWxH) mm 1950 x 430 x 290 1950 x 676 x 462
Dry weight kg 7.5 7.9
Engine Type Air-cooled 2-stroke gasoline
Model Zenoah GZ25N
Max output rpm 1.2Hp (0.9kW) at 7500min
Idle speed rpm 3000±200min
Displacement cm
Fuel
Carburetor Walbro Diaphragm type
Spark plug NGK CMR7H
Fuel tank capacity L 0.65
Transmission Centrifugal clutch, Rigid power transmission shaft
Reduction ratio 7.8
Specifications are subject to change without notice.
3
Mixture (Gasoline 50 : Oil 1) (when using ZENOAH genuine oil)
25.4
-1
-1
3. Warning labels on the machine
(1) (2) (3) (4) (5) (6) (7)
(1) Read owner’s manual before operating this machine.
(2) Wear head, eye and ear protection.
(3) Wear foot protection.
(4) Wear gloves.
(5) Beware of thrown objects.
(6) Warning / Attention
(7) Keep all children, bystanders and helpers 15 meters away from the machine.
If warning label peels off or becomes soiled and
impossible to read, you should contact the
dealer from which you purchased the product
to order new labels and affix them in the required
location(s).
4. Symbols on
Never modify your machine.
We won’t warrant the machine, if you use the
remodeled reciprocation or if you don’t observe
the proper usage written in the manual.
The port to refuel the “MIX GASOLINE”
Position: FUEL TANK CAP
the machine
For safe operation and maintenance, symbols are carved
in relief on the machine. According to these indications,
please be careful not to make a mistake.
The direction to close the choke
Position: ENGINE COVER
The direction to open the choke
Position: ENGINE COVER
15
m
(50ft)
GB-4
5. For safe operation
SGCZ2610DL/SGCZ2610DW
1. Read this manual carefully until
you completely understand and
follow all safety and operating
instructions.
2. Keep this manual handy so that
you may refer to it later whenever any questions arise. Also
note, if you have any questions
which cannot be answered
herein, contact the dealer from
whom you purchased the product.
3. Always be sure to include this
manual when selling, lending, or
otherwise transferring the ownership of this product.
4. Never allow children or anyone
unable to fully understand the
directions given in the manual
to use the machine.
WORKING CONDITION
1. When using the product, you
should wear proper clothing and
protective equipment.
(1) Helmet
(2) Ear protectors
(3) Protection goggles or face
protector
(4) Thick work gloves
(5) Non-slip-sole work boots
2. And you should carry with you.
(1) Attached tools
(2) Properly reserved fuel
(3) Spare blade
(4) Things to notify your working
area (rope, warning signs)
(5) Whistle (for collaboration or
emergency)
(6) Hatchet or saw (for removal of
obstacles)
3. Do not wear loose clothing, jewelry, short trousers, sandals, or go
barefoot. Do not wear anything
which might be caught by a moving part of the unit. Secure hair
so it is above shoulder length.
WORKING CIRCUMSTANCE
1. Never start the engine inside a
closed room or building. Exhaust
gases contain dangerous carbon
monoxide.
2. Never use the product,
a. when the ground is slippery
or when you can’t maintain a
steady posture.
b. At night, at times of heavy fog,
or at any other times when
your field of vision might be
limited and it would be difficult to gain a clear view of the
working area.
c. During rain storms, during
lightning storms, at times of
strong or gale-force winds, or
at any other times when
weather conditions might
make it unsafe to use the
product.
WORKING PLAN
1. You should never use the product when under the influence of
alcohol, when suffering from exhaustion or lack of sleep, when
suffering from drowsiness as a result of having taken cold medicine
or at any other time when a possibility exists that your judgment
might be impaired or that you
might not be able to operate the
product properly and in a safe
manner.
2. When planning your work schedule, allow plenty of time to rest.
Limit the amount of time over
which the product is to be used
continuously to somewhere
around 30 ~ 40 minutes per session, and take 10 ~ 20 minutes of
rest between work sessions. Also
try to keep the total amount of
work performed in a single day
under 2 hours or less.
WARNING
1. If you don’t observe the working
time, or working manner (See
“USING THE PRODUCT”), Repetitive Stress Injury (RSI) could
occur.
If you feel discomfort, redness and
swelling of your fingers or any
other part of your body, see a doctor before getting worse.
2. To avoid noise complaints, in general, operate product between
8 a.m. and 5 p.m. on weekdays
and 9 a.m. to 5 p.m. on weekends.
NOTE
Check and follow the local regulations as to sound level and hours of
operations for the product.
GB-5
G
B
SGCZ2610DL/SGCZ2610DW
5. For safe operation
GB-6
BEFORE STARTING
THE ENGINE
1.
The area within a perimeter of
15 m (50 ft) of the person using
the product should be considered
a hazardous area into which no
one should enter. If necessary,
yellow warning rope, warning
signs should be placed around the
perimeter of the area. When work
is to be performed simultaneously
by two or more persons, care
should also be taken to constantly
look around or otherwise check for
the presence and locations of
other people working so as to
maintain a distance between each
person sufficient to ensure safety.
2. Check the condition of working
area to avoid any accident by hitting hidden obstacles such as
stumps, stones, cans, or broken
glass.
IMPORTANT
Remove any obstacle before beginning work.
3. Inspect the entire unit for loose
fasteners and fuel leakage. Make
sure that the cutting attachment
is properly installed and securely
fastened.
Be sure to attach the cutting at-
4.
tachment guard securely in place,
or you may get serious injury.
5. Always use the harness. Adjust
the harness for comfort before
starting the engine. The harness
should be adjusted so the left
hand can comfortably hold the
handlebar grip approximately
waist high.
STARTING THE ENGINE
1. Keep bystanders and animals at
least 15 m (50 ft) away from the
operating point. If you are approached, immediately stop the
engine.
2. The product is equipped with a
centrifugal clutch mechanism, so
the cutting attachment begins to
rotate as soon as the engine is
started by putting the throttle trigger into the start position. When
starting the engine, place the
product onto the ground in a flat
clear area and hold it firmly in
place so as to ensure that neither
the cutting attachment nor the
throttle trigger come into contact
with any obstacle when the engine starts.
WARNING
Never place the throttle trigger
into the high-speed position when
starting the engine.
3. After starting the engine, check
to make sure that the cutting attachment stops rotating when the
throttle trigger is moved fully back
to its original position. If it continues to rotate even after the throttle
trigger has been moved fully
back, turn off the engine and take
the unit to your authorized
ZENOAH servicing dealer for repair.
USING THE PRODUCT
IMPORTANT
Cut only materials recommended by
the manufacturer. And use only for
tasks explained in the manual.
1. Grip the handles firmly with both
hands using your whole hand.
Place your feet slightly apart
(slightly further apart than the
width of your shoulders) so that
your weight is distributed evenly
across both legs, and always be
sure to maintain a steady, even
posture while working.
2. Keep cutting attachment below
waist level.
3. Maintain the speed of the engine
at the level required to perform
cutting work, and never raise the
speed of the engine above the
level necessary.
4. If the unit starts to shake or vibrate, turn off the engine and
check the whole unit. Do not use
it until the trouble has been properly corrected.
5. Keep all parts of your body away
from rotating cutting attachment
and hot surfaces.
6. Never touch the muffler, spark
plug, or other metallic parts of the
engine while the engine is in operation or immediately after shutting down the engine. Doing so
could result in serious burns or
electrical shock.
Loading...