Page 1
BCZ4505DW / BCZ4505CL / BCZ5010DL / BCZ5010DW / BCZ5010CL
115333110 (001)
OWNER’S MANUAL
BRUSHCUTTERS
G
G
B
B
BCZ4505DW
BCZ4505CL
BCZ5010DL
BCZ5010DW
BCZ5010CL
Original Language
GB-1
Page 2
BCZ4505DW / BCZ4505CL / BCZ5010DL / BCZ5010DW / BCZ5010CL
EC DECLARATION OF CONFORMITY
(Applies to Europe only)
The undersigned manufacturer,
Husqvarna Zenoah Co.,Ltd.,
1-9, Minamidai, Kawagoe, Saitama, Japan,
declares under sole responsibility that the following products referred to in this
declaration conform with the requirement of the following COUNCIL’S DIRECTIVE.
The products referred to are :
DESIGNATION : Brushcutter
MANUFACTURER : Husqvarna Zenoah Co., Ltd.
MODELS : BCZ4505DW BCZ4505CL
SERIAL NUMBERS DATING : 2010 and onwards
This declaration conform with :
・DIRECTIVE 2006/42/EC
(The following standards have been applied: ISO 12100-1,-2, FprEN 15503: 2009)
・DIRECTIVE 2004/108/EC
(The following standards have been applied: EN 61000-6-1, EN 55012 (CISPR 12: 2005))
・DIRECTIVE 2000/14/EC
conformity assessment procedure followed ANNEX V
(The following standards have been applied: ISO 11094)
・DIRECTIVE 2002/88/EC
・ENISO 11806
BCZ5010DL BCZ5010DW
BCZ5010CL
(The year is cleary stated on the rating plate,
follwed by the serial number)
Date :
Signature :
Kiyoshi Honda
General Manager, Development Center
Authorised representative :
Person authorised to compile the technical file :
29 December 2009
Husqvarna AB
SE-561 82 Huskvarna, Sweden
Bo R Jonsson
SE-561 82 Huskvarna, Sweden
GB-2
Page 3
BCZ4505DW / BCZ4505CL / BCZ5010DL / BCZ5010DW / BCZ5010CL
EXPLANATION OF SYMBOLS AND SAFETY WARNINGS
WARNING!!!
RISK OF DAMAGING HEARING
Wear head, eye and ear protection.
G
B
MODEL
SOUND LEVEL
ISO 22868
L
pAeq
BCZ4505DW Blade 45.2 cm
BCZ4505DW Trimmer head 45.2 cm
BCZ4505CL Blade 45.2 cm
BCZ4505CL Trimmer head 45.2 cm
BCZ5010DL Blade 50.6 cm
BCZ5010DL Trimmer head 50.6 cm
BCZ5010DW Blade 50.6 cm
BCZ5010DW Trimmer head 50.6 cm
BCZ5010CL Blade 50.6 cm
BCZ5010CL Trimmer head 50.6 cm
* Specifications are subject to change without notice
1) Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/14/EC.
Reported soundpower level for the machine has been measured with the original cutting attachment that gives the highest level.
The difference between guaranteed and measured sound power is that the guaranteed sound power also includes dispersion in the
measurement result and the variations between different machines of the same model according to Directive 2000/14/EC.
Reported data for equivalent sound pressure level (L
(standard deviation) of 1 dB (A).
2) Reported data for equivalent vibration level (a
3
100 dB(A) 118 dB(A) 4.5 m/s
3
3
3
3
3
3
3
3
3
hv,eq) at the control handle has a typical statistical dispersion (standard deviation) of 1 m/s
98 dB(A) 118 dB(A) 4.5 m/s
100 dB(A) 118 dB(A) 3.1 m/s
102 dB(A) 118 dB(A) 3.1 m/s
101 dB(A) 118 dB(A) 7.3 m/s
100 dB(A) 118 dB(A) 7.3 m/s
101 dB(A) 118 dB(A) 5.0 m/s
99 dB(A) 118 dB(A) 5.1 m/s
100 dB(A) 118 dB(A) 3.1 m/s
103 dB(A) 118 dB(A) 3.3 m/s
pAeq) at the operator’s ear for the machine has a typical statistical dispersion
1)
LwA(guaranteed)
VIBRATION LEVEL
ISO 22867
a
hv,eq
2
2
2
2
2
2
2
2
2
2
APPROVAL NUMBER OF CE EXHAUST EMISSION REGULATION
DIRECTIVE 97/68/EC AMENDED 2002/88/EC
BCZ4505 : e13*97/68SH2G3*2002/88*0097*04
BCZ5010 : e13*97/68SH3G3*2002/88*0622*02
2)
2
.
GB-3
Page 4
BCZ4505DW / BCZ4505CL / BCZ5010DL / BCZ5010DW / BCZ5010CL
SAFETY FIRST
Instructions contained in warnings within this manual marked
with a
into consideration to prevent possible serious bodily injury, and
for this reason you are requested to read all such instructions
carefully and follow them without fail.
WARNINGS IN THE MANUAL
This mark indicates instructions, which must be followed in order to prevent accidents, which could lead to serious bodily injury or death.
This mark indicates instructions, which must be followed, or it
leads to mechanical failure, breakdown, or damage.
This mark indicates hints or directions useful in the use of the
product.
symbol concern critical points which must be taken
WARNING
IMPORTANT
NOTE
Contents
1. Parts location .................................................. 4
2. Specifications ................................................. 5
3. Warning labels on the machine ...................... 5
4. Symbols on the machine ................................ 5
5. For safe operation ........................................... 6
6. Set up ............................................................. 9
7. Fuel ............................................................... 11
8. Operation ...................................................... 12
9. Maintenance ................................................. 16
10. Storage ......................................................... 18
11. Troubleshooting guide .................................. 19
12. Disposal ........................................................ 19
1. Parts location
(1) Primer
(2) Air cleaner cover
(3) Choke lever
(4) Fuel tank
(5) Starter knob
(6) Blade
(7) Angle transmission
(8) Cutting Attachment guard
(9) Loop handle
(10) Shaft tube
(11) Suspention point
(12) Throttle trigger
(13) Stop switch
(14) Throttle cable
(15) Handle
(16) Trimmer head
7
16
DL TYPE
with trimmer
head
11
8
10
13
DW TYPE
15
14
7
5
3
4
1
6
5
3
1
14
12
9
7
6
2
4
12
8
with blade
13
11
10
2
12
CL TYPE
with blade
13
8
10
11
15
5
3
2
4
1
GB-4
Page 5
BCZ4505DW / BCZ4505CL / BCZ5010DL / BCZ5010DW / BCZ5010CL
2. Specification
Model BCZ4505DW BCZ5010DL/DW BCZ4505/5010CL
Overall size (LxWxH) mm DL: 1915x420x260 DW: 1915x655x450 1915x655x530
Dry weight kg 8.5 9.0
Engine Model Zenoah GZ45N Zenoah GZ50N Zenoah GZ45N/GZ50N
Displacement cm
Fuel Mixture (Gasoline 50 : Oil 1)(when using ZENOAH genuine oil)
Carburetor Diaphragm type
Ignition system Flywheel magneto (C.D.I.)
Spark plug NGK CMR7H
Fuel tank capacity L 0.8
Starter Recoil starter
Clutch Centrifugal type
Reduction ratio 1.4
Cutting head rotating direction Counter-clockwise (Operator view)
Specifications are subject to change without notice.
3
45.2 50.6 45.2/50.6
3. Warning labels on the machine
G
B
(1) (2) (3) (4) (5) (6) (7)
(1) Read owner’s manual before operating this machine.
(2) Wear head, eye and ear protection.
(3) Wear foot protection.
(4) Wear gloves.
(5) Beware of thrown objects.
(6) Warning / Attention
(7) Keep all children, bystanders and helpers 15 meters away from the machine.
If warning label peels off or becomes soiled and
impossible to read, you should contact the
dealer from which you purchased the product
to order new labels and affix them in the required
location(s).
4. Symbols on
Never modify your machine.
We won’t warrant the machine, if you use the
remodeled brushcutter or if you don’t observe
the proper usage written in the manual.
The port to refuel the “MIX GASOLINE”
Position: FUEL TANK CAP
the machine
For safe operation and maintenance, symbols are carved
in relief on the machine. According to these indications,
please be careful not to make a mistake.
The direction to close the choke
Position: ENGINE COVER
15
m
(50ft)
The direction to open the choke
Position: ENGINE COVER
GB-5
Page 6
BCZ4505DW / BCZ4505CL / BCZ5010DL / BCZ5010DW / BCZ5010CL
5. For safe operation
GB-6
1. Read this manual carefully until
you completely understand and
follow all safety and operating
instructions.
2. Keep this manual handy so that
you may refer to it later whenever any questions arise. Also
note, if you have any questions
which cannot be answered
herein, contact the dealer from
whom you purchased the product.
3. Always be sure to include this
manual when selling, lending, or
otherwise transferring the ownership of this product.
4. Never allow children or anyone
unable to fully understand the
directions given in the manual
to use the machine.
WORKING CONDITION
1. When using the product, you
should wear proper clothing and
protective equipment.
(1) Helmet
(2) Ear protectors
(3) Protection goggles or face
protector
(4) Thick work gloves
(5) Non-slip-sole work boots
2. And you should carry with you.
(1) Attached tools
(2) Properly reserved fuel
(3) Spare blade
(4) Things to notify your working
area (rope, warning signs)
(5) Whistle (for collaboration or
emergency)
(6) Hatchet or saw (for removal of
obstacles)
3. Do not wear loose clothing, jewelry, short trousers, sandals, or go
barefoot. Do not wear anything
which might be caught by a moving part of the unit. Secure hair
so it is above shoulder length.
WORKING CIRCUMSTANCE
1. Never start the engine inside a
closed room or building. Exhaust
gases contain dangerous carbon
monoxide.
2. Never use the product,
a. when the ground is slippery
or when you can’t maintain a
steady posture.
b. At night, at times of heavy fog,
or at any other times when
your field of vision might be
limited and it would be difficult to gain a clear view of the
working area.
c. During rain storms, during
lightning storms, at times of
strong or gale-force winds, or
at any other times when
weather conditions might
make it unsafe to use the
product.
WORKING PLAN
1.
You should never use the product
when under the influence of alcohol,
when suffering from exhaustion or
lack of sleep, when suffering from
drowsiness as a result of having taken
cold medicine or at any other time
when a possibility exists that your
judgment might be impaired or that
you might not be able to operate the
product properly and in a safe manner.
2. When planning your work schedule, allow plenty of time to rest.
Limit the amount of time over
which the product is to be used
continuously to somewhere
around 30 ~ 40 minutes per session, and take 10 ~ 20 minutes of
rest between work sessions. Also
try to keep the total amount of
work performed in a single day
under 2 hours or less.
WARNING
1. If you don’t observe the working
time, or working manner (See
“USING THE PRODUCT”), Repetitive Stress Injury (RSI) could
occur.
If you feel discomfort, redness and
swelling of your fingers or any
other part of your body, see a doctor before getting worse.
2. To avoid noise complaints, in general, operate product between
8 a.m. and 5 p.m. on weekdays
and 9 a.m. to 5 p.m. on weekends.
NOTE
Check and follow the local regulations as to sound level and hours of
operations for the product.
Page 7
5. For safe operation
BCZ4505DW / BCZ4505CL / BCZ5010DL / BCZ5010DW / BCZ5010CL
BEFORE STARTING
THE ENGINE
1.
The area within a perimeter of
15 m (50 ft) of the person using the
product should be considered a hazardous area into which no one should
enter. If necessary, yellow warning
rope, warning signs should be placed
around the perimeter of the area.
When work is to be performed simultaneously by two or more persons,
care should also be taken to constantly look around or otherwise
check for the presence and locations
of other people working so as to maintain a distance between each person
sufficient to ensure safety.
2.
Check the condition of working area
to avoid any accident by hitting hidden obstacles such as stumps,
stones, cans, or broken glass.
IMPORTANT
Remove any obstacle before beginning work.
3. Inspect the entire unit for loose
fasteners and fuel leakage. Make
sure that the cutting attachment
is properly installed and securely
fastened.
Be sure to attach the cutting at-
4.
tachment guard securely in place,
or you may get serious injury.
5. Always use the shoulder strap.
Adjust the harness for comfort before starting the engine. The harness should be adjusted so the
left hand can comfortably hold the
handlebar grip approximately
waist high.
STARTING THE ENGINE
1. Keep bystanders and animals at
least 15 m (50 ft) away from the
operating point. If you are approached, immediately stop the
engine.
2.
The product is equipped with a centrifugal clutch mechanism, so the cutting attachment begins to rotate as
soon as the engine is started by putting the throttle trigger into the start
position. When starting the engine,
place the product onto the ground in
a flat clear area and hold it firmly in
place so as to ensure that neither the
cutting attachment nor the throttle
trigger come into contact with any ob-
stacle when the engine starts.
WARNING
Never place the throttle into the
high-speed position when starting
the engine.
3. After starting the engine, check
to make sure that the cutting attachment stops rotating when the
throttle trigger is moved fully back
to its original position. If it continues to rotate even after the throttle
trigger has been moved fully
back, turn off the engine and take
the unit to your authorized
ZENOAH servicing dealer for repair.
USING THE PRODUCT
IMPORTANT
Cut only materials recommended by
the manufacturer. And use only for
tasks explained in the manual.
1. Grip the handles firmly with both
hands using your whole hand.
Place your feet slightly apart
(slightly further apart than the
width of your shoulders) so that
your weight is distributed evenly
across both legs, and always be
sure to maintain a steady, even
posture while working.
2. Keep cutting attachment below
waist level.
3. Maintain the speed of the engine
at the level required to perform
cutting work, and never raise the
speed of the engine above the
level necessary.
4. If the unit starts to shake or vibrate, turn off the engine and
check the whole unit. Do not use
it until the trouble has been properly corrected.
5. Keep all parts of your body away
from rotating cutting attachment
and hot surfaces.
6. Never touch the muffler, spark
plug, or other metallic parts of the
engine while the engine is in operation or immediately after shutting down the engine. Doing so
could result in serious burns or
electrical shock.
GB-7
G
B
Page 8
BCZ4505DW / BCZ4505CL / BCZ5010DL / BCZ5010DW / BCZ5010CL
5. For safe operation
• IF SOMEONE COMES
1. Guard against hazardous situations at all times. Warn adults to
keep pets and children away from
the area. Be careful if you are approached. Injury may result from
flying debris.
2. If someone calls out or otherwise
interrupts you while working, always be sure to turn off the engine before turning around.
MAINTENANCE
1. In order to maintain your product
in proper working order, perform
the maintenance and checking
operations described in the
manual at regular intervals.
2. Always be sure to turn off the engine and disconnect the spark
plug wire before performing any
maintenance or checking procedures.
WARNING
The metallic parts reach high temperatures immediately after stopping the engine.
3. When replacing the cutting attachment or any other part, or
when replacing the oil or any lubricant, always be sure to use
only ZENOAH products or
products which have been certified by ZENOAH for use with
the ZENOAH product.
4. In the event that any part must be
replaced or any maintenance or
repair work not described in this
manual must be performed,
please contact a representative
from the store nearest ZENOAH
authorized servicing dealer for
assistance.
5. Do not use any accessory or attachment other than those bearing the ZENOAH mark and recommended for the unit.
6. Under no circumstances should
you ever take apart the product
or alter it in any way. Doing so
might result in the product becoming damaged during operation or the product becoming unable to operate properly.
HANDLING FUEL
1. The engine of the ZENOAH product is designed to run on a mixed
fuel, which contains highly flammable gasoline. Never store cans
of fuel or refill the tank of the unit
in any place where there is a
boiler, stove, wood fire, electrical
sparks, welding sparks, or any
other source of heat or fire which
might ignite the fuel.
2. Never smoke while operating the
unit or refilling its fuel tank.
3. When refilling the tank, always
turn off the engine and allow it to
cool down. Take a careful look
around to make sure that there are
no sparks or open flames anywhere nearby before refueling.
4. Wipe spilled fuel completely using a dry rag if any fuel spillage
occurs during refueling.
5. After refueling, screw the fuel cap
back tightly onto the fuel tank and
then carry the unit to a spot 3 m
or more away from where it was
refueled before turning on the engine.
TRANSPORTATION
1. When hand-carrying the product,
cover over the cutting part if necessary, lift up the product and
carry it paying attention to the
blade.
2. Never transport the product over
rough roads over long distances
by vehicle without removing all
fuel from the fuel tank. If doing so,
fuel might leak from the tank during transport.
GB-8
Page 9
6. Set up
A Package contains the items as illustrated.
1
BCZ4505DW
BCZ5010DW
1
BCZ5010DL
BCZ4505DW / BCZ4505CL / BCZ5010DL / BCZ5010DW / BCZ5010CL
G
B
BCZ5010DL
2
4
9
BCZ4505DW
BCZ5010DW
BCZ5010DL
3
10
BCZ4505CL
BCZ5010CL
BCZ4505CL
BCZ5010CL
56
11
12
1
BCZ4505CL
BCZ5010CL
13
BCZ4505DW
BCZ5010DW
BCZ5010DL
8
7
14
15
16
(1) Unit
(2) Bolt
(3) Handle
(4) Barrier
(5) Cutting attachment guard
(6) Guard skirt
(7) Harness
(8) Harness
(9) Trimmer head
(10) Trimmer head
(11) Blade
(12) Cover
(13) Blade cover
(14) Hexagon socket (S16/S19) with torx driver (T-27)
(15) Bar (Ф4.5)
(16) Owners’ manual
GB-9
Page 10
BCZ4505DW / BCZ4505CL / BCZ5010DL / BCZ5010DW / BCZ5010CL
6. Set up
INSTALLING HANDLE (BCZ5010DL)
• Set the handle and the barrier on the bracket. Attach
them with the 4bolts provided securely.
INSTALLING HANDLE (BCZ4505DW/5010DW)
• Loosen the 4bolts on the upper cap and insert the
handle. Retighten the bolts securely.
INSTALLING HANDLE (BCZ4505CL/5010CL)
• Loosen the handle knob to open the bracket and insert the handle. Retighten the knob securely.
INSTALLING BLADE
1. Put the angled bar(1) into the side holes of the inner
holder and the angle transmission.
2. Remove the nut (Lefthanded) and the outer holder(3)
from the gearshaft.
3. Put the blade onto the inner holder(2). Make the
marked side face the holder.
4. Put the outer holder(3) onto the gearshaft making the
recessed side face the blade.
5. Fasten the blade by the nut and the cover(4).
INSTALLING TRIMMER HEAD
1. While locking the gear shaft by inserting the supplied
bar into the upper holder on the angle transmission,
loosen and remove the nut (left-handed).
2. Detach the cover(1), fit the trimmer head assembly to
the gear shaft. Hand tighten it securely.
INSTALLING CUTTING ATTACHMENT GUARD
• Attach the cutting attachment guard with the bolts
combined to the shaft tube.
GB-10
CUTTING ATTACHMENT GUARD SKIRT FOR
TRIMMER HEAD
• When using trimmer head, make sure to attach the
guard skirt.
BALANCE UNIT
1. Put on harness and attach unit to harness.
2. Slide clamp up or down until unit balances with head
aparting from the ground when using it.
Page 11
7. Fuel
BCZ4505DW / BCZ4505CL / BCZ5010DL / BCZ5010DW / BCZ5010CL
■ FUEL
• Gasoline is very flammable. Avoid smoking or
bringing any flame or sparks near fuel. Make sure
to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3 m (10 ft) away from the
fueling point before starting the engine.
• The Zenoah engines are lubricated by oil specially
formulated for air-cooled 2-cycle gasoline engine use.
If Zenoah oil is not available, use an anti-oxidant added
quality oil expressly labeled for air-cooled 2-cycle
engine use (JASO FC GRADE OIL or ISO EGC
GRADE).
• Do not use BIA or TCW (2-stroke water-cooling type)
mixed oil.
■ RECOMMENDED MIXING RATIO
GASOLINE 50 : OIL 1
(when using ZENOAH genuine oil)
• Exhaust emission are controlled by the fundamental engine parameters and components (eq.,
carburation, ignition timing and port timing) without addition of any major hardware or the introduction of an inert material during combustion.
• These engines are certified to operate on unleaded
gasoline.
• Make sure to use gasoline with a minimum octane
number of 89RON (USA/Canada: 87AL).
• f you use a gasoline of a lower octane value than prescribed, there is a danger that the engine temperature may rise and an engine problem such as piston
seizing may consequently occur.
• Unleaded gasoline is recommended to reduce the
contamination of the air for the sake of your health
and the environment.
• Poor quality gasolines or oils may damage sealing
rings, fuel lines or fuel tank of the engine.
■ HOW TO MIX FUEL
• Pay attention to agitation.
4. Pour in the rest of gasoline and agitate again for at
least one minute. As some oils may be difficult to
agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be
careful that, if the agitation is insufficient, there is an
increased danger of early piston seizing due to abnormally lean mixture.
5. Put a clear indication on the outside of the container
to avoid mixing up with gasoline or other containers.
6. Indicate the contents on outside of container for
easy identification.
■ FUELING THE UNIT
1. Untwist and remove the fuel cap. Rest the cap on a
dustless place.
2. Put fuel into the fuel tank to 80% of the full capacity.
3. Fasten the fuel cap securely and wipe up any fuel
spillage around the unit.
1. Select bare ground for fueling.
2. Move at least 10 feet (3 meters) away from the fueling point before starting the engine.
3. Stop the engine before refueling the unit. At that
time, be sure to sufficiently agitate the mixed gasoline in the container.
■ FOR YOUR ENGINE LIFE, AVOID:
1. FUEL WITH NO OIL (RAW GASOLINE) – It will cause
severe damage to the internal engine parts very
quickly.
GASOHOL – It can cause deterioration of rubber
2.
3. OIL FOR 4-CYCLE ENGINE USE – It can cause
4. Mixed fuels which have been left unused for a
5. In the case of storing the product for a long period
6. In the case of scrapping the used mixed oil con-
• As for details of quality assurance, read the descrip-
or plastic parts and disruption of engine lubri-
and/
cation.
spark plug fouling, exhaust port blocking, or piston
ring sticking.
period of one month or more may clog the carburetor and result in the engine failing to operate properly.
of time, clean the fuel tank after rendering it empty.
Next, activate the engine and empty the carburetor
of the composite fuel.
tainer, scrap it only at an authorized repository site.
tion in the section Limited Warranty carefully. Moreover, normal wear and change in product with no
functional influence are not covered by the warranty.
Also, be careful that, if the usage in the instruction
manual is not observed as to the mixed gasoline,
etc. described therein, it may not be covered by the
warranty.
G
B
1. Measure out the quantities of gasoline and oil to be
mixed.
2. Put some of the gasoline into a clean, approved fuel
container.
3. Pour in all of the oil and agitate well.
GB-11
Page 12
BCZ4505DW / BCZ4505CL / BCZ5010DL / BCZ5010DW / BCZ5010CL
8. Operation
STARTING ENGINE
WARNING
WARNING
• The cutting head will start rotating upon the en-
gine starts.
1. Feed fuel into the fuel tank and tighten the cap se-
curely.
2. Rest the unit on a flat, firm place. Keep the cutting
head off the ground and clear of surrounding objects,
as it will start rotating upon starting of the engine.
3. Push the primer several times until overflown fuel flows
out in the clear tube.
(1)
4. Move the choke lever to the closed position.
(1)
(2)
(3)
(1) choke lever
(2) close
(3) open
5. Set the stop switch to the “RUN” position.
Place the unit on a flat, firm place.
Keep the cutting head clear of everything around it.
(1)
(1)
• The product is equipped with a centrifugal clutch
mechanism, so the cutting attachment begins to
rotate as soon as the engine is started by putting
the throttle trigger into the start position. When
starting the engine, place the product onto the
ground in a flat clear area and hold it firmly in place
so as to ensure that neither the cutting attachment
nor the throttle trigger come into contact with any
obstacle when the engine starts.
IMPORTANT
• Avoid pulling the rope to its end or returning it by releasing the knob. Such actions can cause starter failures.
7. Move the choke lever downward to open the choke.
And restart engine.
8. Allow the engine to warm up for a several minutes
before starting operation.
NOTE
1. When restarting the engine immediately after stopping it, leave the choke open.
2. Overchoking can make the engine hard to start due
to excess fuel. When the engine failed to start after
several attempts, open the choke and repeat pulling
the rope, or remove the spark plug and dry it.
(1) stop switch
6. While holding the unit firmly, pull out the starter rope
quickly until engine fires.
GB-12
STOPPING ENGINE
1. Release the throttle trigger and run the engine for half
a minute.
2. Shift the stop switch to the STOP position.
(1)
(1)
(1) stop switch
IMPORTANT
• Except for an emergency, avoid stopping the engine
while pulling the throttle trigger.
Page 13
8. Operation
BCZ4505DW / BCZ4505CL / BCZ5010DL / BCZ5010DW / BCZ5010CL
ADJUSTING THROTTLE CABLE
• The normal play is 1 or 2 mm when measured at the
carburetor side end. Readjust with the cable adjuster
as required and tighten the screw up.
(3)
(1) Cable adjuster
(2)
(1)
(2) 0.04in (1~2mm)
(3) Screw
ADJUSTING IDLING SPEED
(1)
(1) Idle speed adjuster
(cross screw)
1. When the engine tends to stop frequently at idling
mode, turn the adjusting screw clockwise.
2. When the cutting head keeps rotating after releasing
the throttle trigger, turn the adjusting screw counterclockwise.
METAL BLADE USAGE
1. Check the bolt to fasten the blade and be sure the
bolt has no fault, and no abrasion.
2. Be sure that the blade and the holder have been fastened according to instruction and the blade turns
smoothly without abnormal noise.
WARNING
• The rotating parts fastened incorrectly may cause
serious accident to the operator.
• Make sure that the blade is not bent, warped,
cracked, broken or damaged.
• If you find any error to the blade, discard it and
change new one which is certified by ZENOAH.
G
B
NOTE
•Warm up the engine before adjusting the idling speed.
CUTTER APPLICATION CHART
• Replace by a suitable recommended cutting attachment according to the object to be cut.
• When replacing blade always be sure to use products
which have been certified by ZENOAH.
WARNING
• When sharpening, removing, or reattaching the
blade, be sure to wear thick, sturdy gloves and
use only proper tools and equipment to prevent
injury.
848-JL0-6914
848-JTA-6910
(BCZ4505CL / BCZ5010CL)
• By using the harness, hang the unit on your right side.
Adjust the harness length so that the cutting head
may become parallel to the ground.
WARNING
• Make sure to use harness and cutting attachment
guard. If not, it is very dangerous when you slip or
lose your balance.
• Be sure to use genuine parts made of Zenoah for
blades.In particular, never use special blades such
as shredder blades.If you use a special blade, the
unit may fail.
848-8ZA-3021
GB-13
Page 14
BCZ4505DW / BCZ4505CL / BCZ5010DL / BCZ5010DW / BCZ5010CL
8. Operation
CUTTING METHOD
(a)Use the front left side cutting.
(b) Guide the blade from your right to left with it tilted
slightly to your left.
(c) When mowing a wide area, start working from your
left end to avoid interference of cut grass.
(d) The blade may be seized by weeds if the engine
speed is too low, or the blade cuts too deep into
weeds. Adjust the engine speed and cutting depth
according to the condition of object.
WARNING
• If the grass or other object gets caught in the blade,
or if the unit starts to shake or vibrate, turn off the
engine and check the whole unit. Change the blade
if it has been damaged.
•Turn off the engine and make sure the blade has
completely stop before checking the blade, and
removing any object got caught in.
WARNING
CONTROLLING BLADE BOUNCE
• Blade thrust can cause serious personal injury. Carefully study this section. It is important that you understand what causes blade thrust, how you can reduce
the chance of blade thrust and how you can remain
in control of the unit if blade thrust does occur.
1. What causes blade thrust:
•
Blade thrust can occur when the moving blade contacts an
object that it cannot cut. This contact causes the blade to
stop for an instant and then suddenly move or ”bounce”
away from the object that was hit. The operator can lose
control of the unit and the blade can cause serious personal injury to the operator or any person nearby if the blade
contacts any part of the body.
d. Keep the blade sharp. A dull blade increase the
chance of bounce.
e. Avoid feeding the blade too rapidly. The blade can
bounce away from material being cut if the blade is
fed faster than its cutting capability.
f. Cut only from your right to your left.
g. Keep your path of advance clear of material that has
been cut and other debris.
3. How you can maintain the best control:
a. Keep a good, firm grip on the unit with both hands. A
firm grip can help neutralize bounce. Keep your right
and left hands completely around the respective
handles.
b. Keep both feet spread apart in a comfortable stance
and yet braced for the possibility that the unit could
bounce. Do not overreach. Keep firm footing and
balance.
CUTTING WORK (TRIMMER HEAD USAGE)
WARNING
1. Always wear eye protection such as safety
goggles. Never lean over the rotating cutting head.
Rocks or other debris could be thrown into eyes
and face and cause serious personal injury.
2. Keep the cutting attachment guard in place at all
times when the unit is operated.
TRIMMING GRASS AND WEEDS
• Always remember that the TIP of the line does cut-
ting. You will achieve better results by not crowding
the line into the cutting area. Allow the unit to trim at
its own pace.
1. Hold the unit so the head is off the ground and is tilted
about 20 degrees toward the sweep direction.
2. How you can reduce the chance of blade
thrust:
a. Recognize that blade thrust can happen. By under-
standing and knowing about bounce, you can help
eliminate the element of surprise.
b. Cut fibrous weeds and grass only. Do not let the blade
contact materials it cannot cut such as hard, woody
vines and brush or rocks, fences, metal, etc
c. Be extra prepared for bounce if you must cut where
you cannot see the blade making contact such as in
areas of dense growth.
GB-14
2. You can avoid thrown debris by sweeping from your
left to the right.
3. Use a slow, deliberate action to cut heavy growth.
The rate of cutting motion will depend on the material
being cut. Heavy growth will require slower action than
will light growth.
4. Never swing the unit so hard as you are in danger of
losing your balance or control of the unit.
5. Tr y to control the cutting motion with the hip rather
than placing the full workload on the arm and hands.
Page 15
BCZ4505DW / BCZ4505CL / BCZ5010DL / BCZ5010DW / BCZ5010CL
8. Operation
6. Take precautions to avoid wire, grass and dead, dry,
long-stem weeds from wrapping around the head
shaft. Such materials can stall the head and cause
the clutch to slip, resulting in damage to the clutch
system if repeated frequently.
ADJUSTING THE LINE LENGTH
•Your brush cutter is equipped with a semi- auto type
nylon line head that allows the operator to advance
the line without stopping the engine. When the line
becomes short, lightly tap the head on the ground
while running the engine at full throttle.
• Each time the head is bumped, the line advances
about 25 mm. For better effect, tap the head on bear
ground or hard soil. Avoid bumping in thick, tall grass
as the engine may stall by overload.
• Make the right and left lines the same length when
using the nylon line head.
(Be sure to install the genuine Zenoah cutting attachment guard when using the nylon line head.)
• If the lengths of the right and left lines are different,
the balance of the nylon line head will be disrupted,
resulting in increased vibration and product damage.
• If you feel a vibration increase or shaft tube shaking
while using the nylon line head, immediately stop operation, check the following items, and correct any
problems.
The lengths of the right and left lines are significantly
different.
-->Make them the same length.
The cover is removed.
-->Make sure to install it securely.
There is a crack or damage outside.
-->Replace the damaged part.
• If vibration or shaking persists even after repairing, or
if you cannot identify the cause of abnormality, contact your local authorized Zenoah dealer for repair.
• Never continue to operate the unit when vibration or
shaking of the shaft tube persists.
G
B
9. Maintenance
Every Every Every
System/components Procedure
fuel leaks, fuel spillage wipe out ✔
fuel tank, air filter, fuel filter inspect/clean ✔✔ replace, if necessary
idle speed adjuster ✔
ENGINE
spark plug ✔
intake air cooling vent clean ✔
throttle trigger, stop switch check operation ✔
cutting parts ✔
angle transmission grease ✔
SHAFT
screws/nuts/bolts tighten/replace ✔✔not adjusting screws
cutting attachment guard make sure to attach ✔
see adjusting replace carburetor
idling speed if necessary
clean and readjust GAP: .025 in (0.6 ~ 0.7 mm)
plug gap replace, if necessary
replace if
something’s wrong
Before
use
25 50 100
hours hours hours
after after after
Note
GB-15
Page 16
BCZ4505DW / BCZ4505CL / BCZ5010DL / BCZ5010DW / BCZ5010CL
9. Maintenance
REFILLING TRIMMING LINE
(BCZ4505CL / BCZ5010CL)
WARNING
• For safety reasons, do not use metalreinforced line.
1. Press the latches oppositely on the housing side wall.
Then put off the cover. (*1)
2. Take off the spool from the cover. Clean up the spool
grooves. (*2)
3. A nylon line is cut in 10m. Then that line is cut more in
half. (*3)
4. One nylon line is inserted in the hole at the surface of
the spool. (*4)
5. Other nylon line is inserted in the hole at the bottom
of the spool. (*5)
6. Each line is bent in each groove of the spool.
7. Wind two nylon lines around each groove of the spool
tightly to the direction of the arrow on the spool flanges.
(*6)
8. Hold the lines to the line holding notches on one of
spool outer flanges. Leave 4 inches of the line from
the notches. Do not lot the lines loosen. (*7)
9. Put the spool onto the cover at the position meet the
holding notches with the eyelets on the cover. (*8)
10. Set the lines into the eyelets through the slit on upper
side of the eyelets. (*9)
11. Set the spool into the housing, meet the eyelets to
the eyelet slots of the hosing. (*10)
IMPORTANT
Make sure that the latches fully spread in the windows of the cover.
Latch
Put off
The bottom of spool
One end of the
other nylone line
Hole
Line holding notch
Leave 4 inches
Press
Nylon line
Spool
The surface of spool
One end of
nylon line
Hole
Wind lines around each groove
Follow a note
One of the lines
each can be wound, too
Cover
Line
holding
notch
GB-16
Cover window
Housing latch
Eyelet
Eyelet
Eyelet
slot
Eyelet
Page 17
9. Maintenance9. Maintenance
BCZ4505DW / BCZ4505CL / BCZ5010DL / BCZ5010DW / BCZ5010CL
REFILLING TRIMMING LINE
(BCZ5010DL / BCZ4505DW / BCZ5010DW)
1. For replacement line, use a diameter of 2.4mm(.095in).
The spool is capable for a line upto 6m(20ft) on the
10cm(4”) head. Avoid using a larger line as it may cut
down the trimming performance.
WARNING
• For safety reasons, do not use metalreinforced line.
2. Pinch the slotted area on the both sides of the spool
housing to unhook the bottom cap.
3. Take out the spool and pull off the old line. Put one
end of new line through the spool holes and pull it
until the length is equal between each part of the line.
4. Wind up the line in the correct direction as indicated
on the spool.
5. Hook each end of the line in the slot on the edge of
the spool, and then put the ends through the eyelets
on the housing. Make sure that the spring and the
washers are in place.
6. While holding the spool against the housing, pull the
line ends to release them from the slot.
7. Line up the slot on the bottom cap with the hook on
the housing, press the cap against the housing until it
clicks.
BLADE
• Check the blade and the fasteners for looseness,
cracking, or bending.
• Check the cutting edges and reform with a flat file.
Point :
1. Keep the end corner sharp.
2. Round the root of the edge, using round file.
3. Do not use water when using a grinder.
• It is recommended that filing should be done by
professionals.
• Especially regarding filing the saw blade, Leave it to
the professionals.
WARNING
• Make sure that the engine has stopped and is cool
before performing any service to the machine.
Contact with moving cutting head or hot muffler
may result in a personal injury.
AIR FILTER
• The air filter, if clogged, will reduce the engine performance.
• (1) Filter element and (2) Nonwoven element : Check
and clean each element by air-blow or by washing in
warm and soapy water as required. Dry completely
before installing.
•
If the element is broken or shrunk, replace with a new one.
G
B
(1)(2)
(1) Filter element
(2) Nonwoven element
FUEL FILTER
• When the engine runs short of fuel supply, check the
fuel cap and the fuel filter for blockage.
(1)
SPARK PLUG
• Starting failure and misfiring are often caused by a
fouled spark plug. Clean the spark plug and check
that the plug gap is in the correct range. For a replacement plug, use the correct type specified by
ZENOAH.
(1) Fuel filter
GB-17
Page 18
BCZ4505DW / BCZ4505CL / BCZ5010DL / BCZ5010DW / BCZ5010CL
9. Maintenance
INTAKE AIR COOLING VENT
WARNING
0.6~0.7 mm
• REPLACEMENT PLUG IS A NGK CMR7H.
IMPORTANT
• Note that using any spark plug other than those des-
ignated may result in the engine failing to operate properly or in the engine becoming overheated and damaged.
• To install the spark plug, first turn the plug until it is
finger tight, then tighten it a quarter turn more with a
socket wrench.
TIGHTENING TORQUE:
MUFFLER
WARNING
• Inspect periodically, the muffler for loose fasteners, any damage or corrosion. If any sign of exhaust leakage is found, stop using the machine
and have it repaired immediately in the repair specialty store.
• Note that failing to do so may result in the engine
catching on fire.
87 ~ 104 in-lbs
(9.8 ~ 11.8 N.m.)
• Check the intake air cooling vent after every 25
hours of use for blockage, and remove any waste
which has attached itself to the brushcutter.
IMPORTANT
• If waste gets stuck and causes blockage around the
intake air cooling vent, it may cause the engine to overheat, and that in turn may cause mechanical failure
on the part of the brushcutter.
(1)
(1)
(1) Intake air cooling vent
■ PERIODICAL SERVICE POINTS
1. CYLINDER FINS
Periodically check and clean the cylinder fins in the repair specialty store.
ANGLE TRANSMISSION
• The reduction gears are lubricated by multipurpose,
lithium-based grease in the angle transmission.
Supply new grease every 25 hours of use or more
often depending on the job condition.
• Remove the bolt of the grease nipple and the bolt
opposite side of the grease nipple. Install new grease
into the grease nipple to arrange for old grease to
exit from the opposite side.
(1)
(1) Grease
GB-18
10. Storage
Aged fuel is one of major causes of engine starting failure. Before storing the unit, empty the fuel tank and run
the engine until it uses all the fuel left in the fuel line and
the carburetor. Store the unit indoor taking necessary
measures for rust prevention.
Page 19
BCZ4505DW / BCZ4505CL / BCZ5010DL / BCZ5010DW / BCZ5010CL
11. Troubleshooting guide
Case 1. Starting failure
CHECK PROBABLE CAUSES ACTION
fuel tank → incorrect fuel → drain it and use correct fuel
fuel filter → fuel filter is clogged → clean
carburetor adjustment screw → out of normal range → adjust to normal range
sparking (no spark) → spark plug is fouled/wet → clean/dry
→ plug gap is incorrect → correct (GAP: 0.6 ~ 0.7 mm)
spark plug → disconnected → retighten
Case 2. Engine starts but does not keep running/hard re-starting
CHECK PROBABLE CAUSES ACTION
fuel tank → incorrect fuel or staled fuel → drain it and use correct fuel
carburetor adjustment screw → out of normal range → adjust to normal range
muffler, cylinder (exhaust port) → carbon is built-up → consult with the repair specialty store
air cleaner → clogged with dust → air blow or wash
cylinder fin, fan cover → clogged with dust → consult with the repair specialty store
When your unit seems to need further service, please consult with our ZENOAH service shop in your area.
12. Disposal
• When you dispose of the machine, do not disas-
semble the machine.
• When you dispose of the machine, fuel, oil, be sure
to follow your local regulations.
G
B
Limited warranty
Should any failure occur on the product under normal operating conditions within the applicable warranty period, the
failed part will be replaced or repaired free of charge by a
ZENOAH authorized dealer.
WARRANTY PERIOD: 1 year (6 months if used professionally, and 30 days if used for rental purpose) from the date of
initial purchase.
THE PURCHASER SHALL BEAR COSTS OF TRANSPORTING
THE UNIT TO AND FROM THE ZENOAH DEALER.
THE PURCHASER SHALL NOT BE CHARGED FOR DIAGNOSTIC LABOR WHICH LEADS TO THE DETERMINATION
THAT A WARRANTED PART IS DEFECTIVE, IF THE DIAGNOSTIC WORK IS PERFORMED AT THE ZENOAH DEALER.
THE PURCHASER OR OWNER IS RESPONSIBLE FOR THE
PERFORMANCE OF THE REQUIRED MAINTENANCE AS
DEFINED BY THE MANUFACTURER IN THE OWNER/OPERATOR MANUAL.
ANY WARRANTED PART WHICH IS NOT SCHEDULED FOR
REPLACEMENT AS REQUIRED MAINTENANCE, OR WHICH
IS SCHEDULED ONLY FOR REGULAR INSPECTION TO THE
EFFECT OF REPAIR OR “REPLACE AS NECESSARY” SHALL
BE WARRANTED FOR THE WARRANTY PERIOD. ANY WARRANTED PART WHICH IS SCHEDULED FOR REPLACEMENT
AS REQUIRED MAINTENANCE SHALL BE WARRANTED FOR
THE PERIOD OF TIME UP TO THE FIRST SCHEDULED REPLACEMENT POINT FOR THE PART.
ANY REPLACEMENT PART THAT IS EQUIVALENT IN PERFORMANCE AND DULABILITY MAY BE USED IN NON-WARRANTY MAINTENANCE OR REPAIRS, AND SHALL NOT REDUCE THE WARRANTY OBLIGATION OF THE COMPANY.
THE COMPANY IS LIABLE FOR DAMAGES TO OTHER ENGINE COMPONENTS CAUSED BY THE FAILURE OF A WARRANTED PART STILL UNDER WARRANTY.
THE WARRANTY DOES NOT APPLY TO THOSE UNITS
WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF INSTRUCTION LISTED IN THE OWNER/OPERATOR MANUAL
FOR PROPER USE AND MAINTENANCE OF THE UNITS
ACCIDENT MISHANDLING, ALTERATION, ABUSE, IMPROPER LUBRICATION, USE OF ANY PARTS OR ACCESSORIES OTHER THAN THOSE SPECIFIED BY THE COMPANY, OR OTHER CAUSES BEYOND THE COMPANY’S CONTROL.
THIS WARRANTY DOES NOT COVER THOSE PARTS REPLACED BY NORMAL WEAR OR HARMLESS CHANGES IN
THEIR APPEARANCE.
THERE ARE NO OTHER EXPRESS WARRANTIES.
IMPLIED WARRANTIES INCLUDING THOSE OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO TWO (2) YEARS OF HOME USE
[ONE (1) YEAR FOR ANY OTHER USE] FROM THE ORIGINAL DELIVERY DATE.
LIABILITIES FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGE UNDER ANY AND ALL WARRANTIES ARE EXCLUDED.
IF YOU NEED TO OBTAIN MORE INFORMATION, PLEASE
CALL YOUR NEAREST SERVICE CENTER,
OR CHECK PLEASE ZENOAH WEB SITE
http://www.zenoah.net
GB-19
Loading...