Zenoah BC2603DW, BC2603DL User Manual
OWNER’S MANUAL
848JA093A0 (311)
BRUSHCUTTERS
G
G
B
B
BC2603DL
BC2603DW
GB-1
EXPLANATION OF SYMBOLS AND SAFETY WARNINGS
WARNING!!!
RISK OF DAMAGING HEARING
GB-2
MODEL
BC2603DL
BC2603DW
MAY INVOLVE A DAILY LEVEL OF PERSONAL EXPOSURE TO NOISE
IN NORMAL CONDITIONS OF USE, THIS MACHINE
FOR THE OPERATOR EQUAL TO OR GREATER THAN
85 dB(A)
SOUND LEVEL VIBRATION LEVEL
ISO 7916
idling
2.4 m/s
1.7 m/s24.9 m/s
25.4 cm
25.4 cm
EN27917
LpA
3
97.3 dB(A)
3
97.3 dB(A)
ISO 10884
measured
107.9 dB(A)
107.9 dB(A)
LwA
guaranteed
110 dB(A)
110 dB(A)
2
racing
3.0 m/s
2
2
SAFETY FIRST
Instructions contained in warnings within this manual marked
with a symbol concern critical points which must be taken
into consideration to prevent possible serious bodily injury, and
for this reason you are requested to read all such instructions
carefully and follow them without fail.
WARNINGS IN THE MANUAL
WARNING
This mark indicates instructions, which must be followed in order to prevent accidents, which could lead to serious bodily injury or death.
IMPORTANT
This mark indicates instructions, which must be followed, or it
leads to mechanical failure, breakdown, or damage.
NOTE
This mark indicates hints or directions useful in the use of the
product.
Contents
1. Parts location .................................................. 4
2. Specifications ................................................. 4
3. Warning labels on the machine ...................... 5
4. Symbols on the machine ................................ 5
5. For safe operation........................................... 6
6. Set up ............................................................. 9
7. Fuel ............................................................... 10
8. Operation...................................................... 11
9. Maintenance ................................................. 13
10. Storage ......................................................... 15
11. Troubleshooting guide .................................. 16
G
B
1. Parts location
(1) Primer pump
(2) Air cleaner cover
(3) Choke lever
(4) Fuel tank
(5) Starter knob
(6) Blade
(7) Gear case
(8) Debris guard
(9) Loop handle
(10) Drive shaft housing
(11) Sholder strap hanger
(12) Throttle lever
(13) Ignition switch
(14) Throttle cable
(15) Protector
(16) Handle
7
6
3
BC2603DL BC2603DW
13
11
9
10
8
12
6
5
1
4
2
14
10
7
8
5
3
13
11
12
16
14
15
1
4
2
GB-3
2. Specification
BC2603DL / BC2603DW
Overall size (L W H) ............................ 1800 x 395 x 315 / 1800 x 610 x 520 mm
Dry weight .................................................................................................. 5.3 / 6.7 kg
Engine
Model ............................................................................................... Zenoah G26L
Displacement ........................................................................................... 25.4 cm
Fuel............................................................................ Mixture (Gasoline 50 : Oil 1)
Carburetor .................................................................................... Diaphragm type
Ignition system ...........................................Transistor controlled flywheel magneto
Spark plug........................................................................................NGK BPMR7A
Fuel tank capacity............................................................................................... 0.75 L
Starter ...................................................................................................... Recoil starter
Clutch.................................................................................................. Centrifugal type
Reduction ratio.................................................................................................... 1.357
Cutting head rotating direction ............................. Counter-clockwise (Operator view)
Specifications are subject to change without notice.
3
3. Warning labels on
the machine
Read owner’ s manual bef ore operating this machine.
Wear head, eye and ear protection.
Warning / Attention
Keep all children, bystanders and helpers 15
meters away from the machine.
If warning label peels off or becomes soiled and
impossible to read, you should contact the
dealer from which you purchased the product
to order new labels and affix them in the required
location(s).
Never modify your machine.
We won’t warrant the machine, if you use the
remodeled brushcutter or if you don’t observe
the proper usage written in the manual.
4. Symbols on the
machine
For safe operation and maintenance, symbols are carved
in relief on the machine. According to these indications,
please be careful not to make a mistake.
The port to refuel the “MIX GASOLINE”
Position: FUEL TANK CAP
The direction to close the choke
Position: AIR CLEANER COVER
GB-4
The direction to open the choke
Position: AIR CLEANER COVER
5. For safe operation
1. Read this manual carefully until
you completely understand and
follow all safety and operating
instructions.
2. Keep this manual handy so that
you may refer to it later whenever any questions arise. Also
note, if you have any questions
which cannot be answered
herein, contact the dealer from
whom you purchased the product.
3. Always be sure to include this
manual when selling, lending, or
otherwise transferring the ownership of this product.
4. Never allow children or anyone
unable to fully understand the
directions given in the manual
to use the machine.
WORKING CONDITION
1. When using the product, you
should wear proper clothing and
protective equipment.
(1) Helmet
(2) Ear protectors
(3) Protection goggles or face
protector
(4) Thick work gloves
(5) Non-slip-sole work boots
2. And you should carry with you.
(1) Attached tools
(2) Properly reserved fuel
(3) Spare blade
(4) Things to notify your working
area (rope, warning signs)
(5) Whistle (for collaboration or
emergency)
(6) Hatchet or saw (for removal of
obstacles)
3. Do not wear loose clothing, jewelry, short tr ousers, sandals, or go
barefoot. Do not wear anything
which might be caught by a moving part of the unit. Secure hair
so it is above shoulder length.
WORKING CIRCUMSTANCE
1. Never star t the engine inside a
closed room or building. Exhaust
gases contain dangerous carbon
monoxide.
2. Never use the product,
a. when the ground is slippery
or when you can’t maintain a
steady posture.
b. At night, at times of heavy fog,
or at any other times when
your field of vision might be
limited and it would be difficult to gain a clear view of the
working area.
c. During rain storms, during
lightning storms, at times of
strong or gale-force winds, or
at any other times when
weather conditions might
make it unsafe to use the
product.
WORKING PLAN
1. You should never use the product when under the influence of
alcohol, when suffering from exhaustion or lack of sleep, when
suffering from drowsiness as a result of having taken cold medicine
or at any other time when a possibility exists that your judgment
might be impaired or that you
might not be able to operate the
product properly and in a safe
manner.
2. When planning your work schedule, allow plenty of time to rest.
Limit the amount of time over
which the product is to be used
continuously to somewhere
around 30 ~ 40 minutes per session, and take 10 ~ 20 minutes of
rest between work sessions. Also
try to keep the total amount of
work performed in a single day
under 2 hours or less.
WARNING
1. If you don’t obser ve the working
time, or working manner (See
“USING THE PRODUCT”), Repetitive Stress Injury (RSI) could
occur.
If you feel discomf ort, redness and
swelling of your fingers or any
other part of your body , see a doctor before getting worse.
2. To avoid noise complaints, in general, operate product between
8 a.m. and 5 p.m. on weekdays
and 9 a.m. to 5 p .m. on week ends.
NOTE
Check and follow the local regulations as to sound level and hours of
operations for the product.
GB-5
G
B
Loading...