Z35
KNX Capacitive Touch Panel
ZVI-Z35
USER MANU AL
Application Program Version: [2.3]
User Manual Version: [2.3]_b
www.zennio.com
Z35
http://www.zennio.com Technical Support: http://support.zennio.com
2
CONTENTS
Contents ................................................................................................................................... 2
Document updates ................................................................................................................... 4
1 Introduction ...................................................................................................................... 5
1.1 Z35 ............................................................................................................................. 5
1.2 Functionality .............................................................................................................. 7
1.3 Installation ................................................................................................................. 9
1.4 Start-Up and Power Loss .......................................................................................... 10
2 Update Objects after Reset .............................................................................................. 11
3 Configuration .................................................................................................................. 12
3.1 Main Configuration .................................................................................................. 12
3.1.1 GENERAL .............................................................................................................. 12
3.1.2 Translations .......................................................................................................... 18
3.1.3 Backlight .............................................................................................................. 20
3.1.4 Security ................................................................................................................ 20
3.1.5 Internal Temperature Sensor ................................................................................ 23
3.1.6 Screensaver .......................................................................................................... 23
3.1.7 Ambient Luminosity Sensor .................................................................................. 26
3.1.8 Touch Locking....................................................................................................... 26
3.1.9 Sounds ................................................................................................................. 27
3.1.10 ADVANCED ......................................................................................................... 29
3.2 MENU ...................................................................................................................... 36
3.2.1 Configuration ....................................................................................................... 39
3.3 Page n ...................................................................................................................... 40
3.3.1 Configuration ....................................................................................................... 40
3.3.2 Box i ..................................................................................................................... 42
3.3.3 Setpoint ............................................................................................................... 75
3.3.4 Fan ....................................................................................................................... 76
3.4 Configuration Page ................................................................................................... 78
3.5 Inputs....................................................................................................................... 81
3.5.1 Binary Input.......................................................................................................... 81
Z35
http://www.zennio.com Technical Support: http://support.zennio.com
3
3.5.2 Temperature Probe .............................................................................................. 81
3.5.3 Motion Detector................................................................................................... 81
3.6 Thermostat .............................................................................................................. 83
ANNEX I. Communication Objects ........................................................................................... 84
Z35
http://www.zennio.com Technical Support: http://support.zennio.com
4
DOCUMENT UPDATES
Version
Changes
Page(s)
[2.3]_b
Clarification about time setting.
16
[2.3]_a
Changes in the application program:
Support for new touch panel.
-
[2.2]_a
Changes in the application program:
New object to force activity/inactivity state of
the device.
-
Screensaver image update through an ETS
application.
Optimisation of Temperature Probe and
Brightness modules.
[2.1]_a
Changes in the application program:
Optimization of the Luminosity and Proximity
module.
-
[2.0]_a
Changes in the application program:
New icons.
New page types: thermostat and thermostat +
2 boxes.
General color mask, for boxes, icons and
buttons.
-
Differents types of indicator representation.
Possibility of disabling the home button.
New direct access control to the page.
[1.3]_a
Changes in the application program:
Optimization of the press detection algorithm.
-
[1.1]_a
Changes in the application program:
New parameter: Sound Type.
-
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
5
1 INTRODUCTION
1.1 Z35
Z35 is an easily and intuitively controllable high-performance touch screens from
Zennio. The built-in features and functions make them the ideal solution for integral room
control in hotels, offices or any other environments where controlling climate systems,
lighting systems, shutters, scenes, etc. is required
The most outstanding features of Z35 are:
3.5 inch (3.5’’) backlit capacitive touch panel with backlit ‘Home’ button
incorporated, with screen resolution of 320 x 240 pixel.
Multiple direct-action functions, fully customisable.
Control distribution across up to 7 customisable pages + 1 configuration page.
Full climate management.
Programmable timers.
Scene control.
Alarm control.
Screensaver with customizable image.
Multi-Language.
2 independent thermostats.
Built-in temperature sensor.
Ambient luminosity sensor for brightness automatic adjustment.
Proximity sensor for quick start.
Buzzer for an audible acknowledgement of user actions (with the possibility of
disabling it either by parameter or by object).
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
6
Possibility of locking / unlocking the touch panel through binary orders or
scenes, and of setting a timed/automatic locking of the device (cleaning
function).
Welcome greeting on the display and Welcome Back object (binary or scene)
Celsius and Fahrenheit temperature scales for the on-screen indicators, being
possible to select them in parameters or through communication object.
4 customisable analogue-digital inputs.
Heartbeat or periodic “still-alive” notification.
Elegant design, available in various colours.
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
7
1.2 FUNCTIONALITY
Application program feature the following functions:
7 Pages, with up to 6 Fully-Customisable Boxes each, all of them fully
combinable and configurable by the integrator. These pages can be configured
as normal or thermostat type pages.
Box
Funcionality
Page
Normal
Thermostat
Indicators
Binary (icon, text)
Enumerated (icon, text)
Unsigned integer (1 / 2bytes)
Signed integer (1 / 2 / 4bytes)
Scaling (percentage)
Temperature
Float (2 / 4bytes)
Text (14bytes)
1-button
Control
Switch (pre-set value, switch)
Two objects (short press / long press)
Hold & Release
Scene (run / save)
Constant (counter, scaling, float)
2-button
Control
Switch (icon, text).
Switch + Indicator (counter, scaling, temperature)
Two objects (short press / long press)
Constant (counter, scaling, float)
Enumeration
Shutters
Light dimming
Multimedia
Climate
Specific
Control
Temperature Setpoint
Mode (cool/heat, extended)
Special modes
Fan
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
8
Other
Controls
RGB
RGBW
Daily / Weekly Timer
Alarm
Page direct link
Boxes on
thermostat
pages
Setpoint control
Fan control
Table 1. Controls available in each type of page
1 Configuration Page (optional), which contains the brightness and sounds
settings, the calibration of the built-in temperature probe, the programming
button, Hour/Date settings and Reset configuration.
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
9
1.3 INSTALLATION
Figure 1 shows the connection outline of the device:
Figure 1. Schematic diagram.
Z35 is connected to the KNX bus through the built-in terminal (6). An external DC power
supply is not needed.
A short press on the Prog./Test button (7) will make the device enter the programming
mode. The Prog./Test LED (8) will then light in red. On the contrary, if this button is held
while the device gets connected to the bus, Z35 will enter the safe mode. In such case,
the programming LED will blink in red colour.
For detailed information about the technical features of Z35, as well as on security and
installation procedures, please refer to the device Datasheet, bundled within the device
packaging and also available at www.zennio.com.
3
6
4
1
2
7
8
5
1. Touch panel.
2. Backlit ‘Home’ button.
3. Luminosity and ProximitySensors.
4. Input connectors.
5. KNX connector.
6. Programation Button.
7. Programation LED.
8. Temperatura Probe.
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
10
1.4 START-UP AND POWER LOSS
After download or device reset it is necessary to wait for about 2 minutes without
performing any action in order to make it possible a proper calibration of the proximity
sensor and luminosity sensor.
It is recommended not to approach less than 50 cm from the device during this time and
to avoid that the light strikes directly.
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
11
2 UPDATE OBJECTS AFTER RESET
The aim of this functionality is allowing the integrator to make a read request to the
statuses of the device objects after a reset. There are two situations in which this
functionality may be useful:
In case of a Z35 reset, if there have been changes in the bus while the Z35 was
off, after the reset, the objects in Z35 keep the same value as before the reset,
but not their actual value in the installation.
In addition, after programming from ETS, all objects are initialized to their default
values, but not to their actual values in the installation.
When a bus failure or ETS programming occurs, read requests of all the following objects
will be sent gradually (to prevent bus overload):
General objects: date and time, scene (reception), disabling pushbuttons,
cleaning function, external temperature, backlight mode, brightness, pulse sound
enable and temperature scale.
Indicator objects.
Timer enabling objects.
Alarm confirmation object.
Ventilation control: Auto mode dedicated object.
14-byte Text indicator.
RGB and RGBW objects.
Objects that will NOT be updated are:
Control objects.
Alarm trigger.
4-Bit Light Dimming.
4-Bit RGB/RGBW Dimming.
Shutter: Stop/Step.
The time and date objects of Z35 will be read from the bus always after a reset,
regardless of whether this functionality is active or not.
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
12
3 CONFIGURATION
After importing the corresponding database in ETS and adding the device into the
topology of the desired project, the configuration process begins by entering the
Parameters tab of the device.
3.1 MAIN CONFIGURATION
This tab is divided into multiple screens, all of which contain a set of global parameters
regarding the general functionality of the device, and therefore not specifically related to
a particular page of the user interface.
3.1.1 GENERAL
The "General" tab contains general settings. Most are checkboxes for enabling/disabling
other functionalities.
ETS PARAMETERISATION
Figure 2. General.
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
13
The following parameters are shown:
Inputs [disabled/enabled]1: enables or disables the “Inputs” tab in the tree on the
left, depending on whether the device will or will not be connected any external
accessories. For more information, see section 3.5.
Thermostats [disabled/enabled]: enables or disables the “Thermostat” tab in the
tree on the left. For more information, see section 3.6.
Heartbeat (Periodic Alive Notification) [disabled/enabled]: incorporates a one-
bit object to the project (“[Heartbeat] Object to Send ‘1’”) that will be sent
periodically with value “1” to notify that the device is still working (still alive).
Figure 3. Heartbeat.
Note: the first sending after download or bus failure takes place with a delay of
up to 255 seconds, to prevent bus overload. The following sendings march the
period set.
Home Button Enabled [disabled/enabled]: enables or disables the home button
to access to the menu page.
Show Time [disabled/enabled]: permits setting whether the current time
(according to the internal clock) is displayed in the upper-left corner of any page
or not.
Show Temperature [No / Internal Temperature Probe / External Value]: sets
whether the current temperature should show or not in the upper right corner of
every page, being necessary in such case to choose the source of the
temperature value: “Internal temperature probe” or “External value”. If the latter
is chosen, an object named “[General] External temperature” will be enabled,
so that it can be grouped with any other object that sends temperature values.
1
The default values of each parameter will be highlighted in blue in this document, as follows:
[default/rest of options].
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
14
Button Box Style [No frame / Colored frame / Black frame]: permits selecting a
frame for the buttons of controls and pages, in order to distinguish them from the
indicators.
Figure 4. Button box (black, white color, no box).
Global Color Mask [White / Color select by dropdown]: permits selecting the
color that will be applied to all the elements of the screen in a general way.
Note: It is possible to set a different color in the desired boxes and buttons by
using a specific parameter in their configuration tab (see section 3.3.2).
First Weekday [Monday / Sunday]: sets the first day of week on calendar.
Weekdays initials [MTWTFSS]: permits customising the label that will represent
each of the weekdays on the screen. A seven-character string (including letters
or numbers), ordered according to the above First Weekday parameter, must be
entered – each of the characters will represent one weekday.
Hour Update Request Delay [disabled/enabled]: sets a sending delay
[1…65535] [s/min/h] for the date/time request when the device starts up.
Update Objects [Disabled/After Programming/After Reset/After Programming
and Reset]: enables the sending of read requests to update status objects and
indicators (see section 2 for further details). There are four options available,
some of them with a configurable delay:
“Disabled”: no read request, therefore objects are not updated.
“After Programming”: read requests are sent after a complete or partial
download (or when pressing the reset button in the configuration page, if set
as “Parameters Reset”, see section 3.4), after the parameterised delay
([0…10…65535] [s/min/h]).
“After Reset”: read request are sent when a reset occurs (bus failure, the
Reset Device ETS option or when pressing the reset button in the
configuration page, if set as “Z35 Reboot”, see section 3.4), after the
parameterised delay ([0…10…65535] [s/min/h]).
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
15
“After Programming and Reset”: combination of the two above options.
Screensaver [disabled/enabled]: enables or disables the “Screensaver” tab in
the tree on the left. See section 3.1.6 for details.
Time to Consider Inactivity [1…65535] [s/min/h]: time that must elapse since
the last press and/or proximity detection to consider inactivity state. Then the
display backlight will dim. See section 3.1.3.
Proximity Sensor [disabled/enabled]: enables the proximity sensor. This
functionality permits “waking up” the device display when detecting presence
through the proximity sensor
Please refer to the user manual “Proximity and Luminosity Sensor” (available
in the Z35 product section at the Zennio homepage, www.zennio.com) for
detailed information about the functionality and the configuration of the related
parameters.
Ambient Luminosity Sensor [disabled/enabled]: enables or disables the
ambient luminosity sensor. When enabled, a new tab is added in the tree on the
left (see section 3.1.7).
Touch Locking [disabled/enabled]: enables or disables the possibility of locking
the touch by object. When enabled, a new tab is added in the tree on the left (see
section 3.1.8).
Sounds [Default/Custom]: sets whether the sound functions (button beeps,
alarm and doorbell) should work according to the pre-defined configuration
(“Default”) or to a user-defined configuration (“Custom”) (see section 3.1.9).
Advanced Configuration [enabled/disabled]: enables or disables the
“Advanced” tab in the tree on the left (see section 3.1.10).
The project topology shows the following objects by default:
[General] Time: 3-byte object for setting the internal time of the device, for
example, by linking it to a KNX clock. This object also allows read requests, so
the current time of the device can be checked. It is also automatically sent after
time changes made by the user from the screen itself.
Note: although the DPT of this object considers a field for setting the day of the
week, Z35 calculates it from the date and therefore ignores that field.
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
16
Important: Z35 does not have an RTC clock or battery to keep track of the
time in the absence of power. Therefore, it is important to receive the time
periodically from a device that obtains it through NTP and/or has a battery to
prevent delays during bus failures.
[General] Date: 3-byte object for setting the internal date of the device, for
example, by linking it to a KNX clock. This object also allows read requests, so
the current date of the device can be checked. It is also automatically sent after
date changes made by the user from the screen itself.
[General] Scene: Receive and [General] Scene: Send: objects for respectively
receiving and sending scene values from/to the KNX bus whenever it is
necessary (e.g., when the user touches a button that has been configured to send
scene commands; see section 3.3.2.2.4).
[General] Activity: 1-bit object to force activity/inactivity state on the device. For
further information, please refer to the user manual “Proximity and Luminosity
Sensor” and “Brightness” (available in the Z35 product section at the Zennio
homepage, www.zennio.com).
[General] Display - Brightness: 1-byte percentage object for changing the
display brightness level.
[General] Proximity Sensor, [General] External Proximity Detection and
[General] Proximity Detection: 1-bit object whose functionality is tied to the
proximity sensor. For further information, please refer to the user manual
“Proximity and Luminosity Sensor” (available in the Flat Display product
section at the Zennio homepage, www.zennio.com).
[General] Translations - Select Language: 1 and 2-byte objects for changing
the language showed in the screen when receiving a value through the bus (see
section 3.1.2).
[General] Translations - Main Language: 1-bit object that, after the reception
of the value “1” from the bus, will load the main language (see section 3.1.2).
[General] Temperature Scale: 1-bit object which permits changing in runtime
the scale of the temperatures that may show on the screen (see section 3.1.10).
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
17
[Internal Temp. Probe] Current Temperature: 2-byte object through which the
value of the current measurement of the built-in sensor will be sent to the bus,
according to the parameterisation (see section 3.1.5).
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
18
3.1.2 TRANSLATIONS
Texts shown on the screen can be translated into up to five different languages.
Texts of page titles, box titles, indicators, etc. are entered by parameter in the
corresponding configuration tab. For each language enabled, an additional textbox is
displayed to enter the translation.
Note: depending on the space occupied by the charactere on the screen, the full text
entered may not be displayed.
Switching from language to another can be done through two types of communication
objects:
Up to five 1-bit objects, one for each language. If this is enabled, when a “1” is
received through any of this, the corresponding language is activated in the
device.
A 1-byte scene object. The expected values in this object are fixed, from 0 to 4,
to select the language. If the corresponding language to the received value is not
enabled, the texts will be displayed in the main. If an out-of-range value is
received, it does not change the active language.
A 2-byte ASCII object. The expected values for this object are two characters of
the ASCII code, corresponding to ISO 639-1. If the received character pair does
not correspond to any enabled language, the texts will be represented in the main
language.
Note: please refer to http://en.wikipedia.org/wiki/List_of_ISO_639-1_codes for a
table with the language codes.
On the other hand, Z35 allows the use of Latin, Greek and Cyrillic characters for the texts
displayed on the screen.
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
19
ETS PARAMETERISATION
Figure 5. Translations.
Main language [enabled]: read-only parameter to make it evident that the main
language is always enabled.
Select language: list of the available languages.
Language X [disabled/enabled]: enables the additional language X.
Select language: list of available languages to select the language X.
Only the Main language is enabled by default.
While Translations stays enabled, the following objects are visible:
“[General] Translations – Select language” (one-byte).
“[General] Translations – Main language” (one-bit).
“[General] Translations – Select language” (two-byte).
Up to four specific objects for the additional languages will be also shown, if required:
“[General] Translations – Language X” (one bit).
These objects work accordingly to the behaviour mentioned above.
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
20
3.1.3 BACKLIGHT
Z35 allows managing the brightness of the display according to two operating modes:
normal mode and night mode.
Note: Contrast is not a configurable feature in the device.
Please refer to the specific manual “Brightness” (available in the Z35 product section at
the Zennio website, www.zennio.com) for detailed information about the functionality and
the configuration of the related parameters.
3.1.4 SECURITY
Any box or page will be given the possibility of restricted access by password. Setting
one or two different passwords is possible, so the integrator can afterwards configure
whether the access to a page or box will be protected by one password or another, or
remain unprotected – every page can be independently configured.
Buttons that lead to a protected page or box will show a little lock icon overlaid on their
lower left corner.
Figure 6 shows the “enter password” dialog shown to the user when trying to access a
protected page.
Figure 6. Security Pop up.
In case of setting up two levels, the first one is assumed to be enclosed by the second
one. This means that whenever the device asks the user to type password #1 (to enter
a certain page); password #2 will also be accepted. On the contrary, password #1 cannot
be used instead of password #2. This behaviour permits, therefore, making password #2
available to users with further privileges while password #1 is assigned to users with
fewer privileges.
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
21
Moreover, when accessing to a protected page, all the boxes and pages with the same
or lower access level of the introduced password, are automatically unlocked. It can be
set if the elements are relocked after a time period or a page switch.
ETS PARAMETERISATION
This screen permits selecting how many security levels (one or two) will be available for
the configuration of the access to the control pages or the boxes.
Figure 7. Security.
Security Levels [One Level / Two Levels]: dropdown list for selecting whether
one (default option) or two security levels will be available.
Note: with independence of the option selected here, it will be necessary to
establish the security level desired for each specific page of controls.
Protect Again [After a Time Period/After a Page Switch / After a Time Period or
a Page Switch]: sets when is re-activated the security of pages or boxes
unlocked. When selecting the first or the last option, a new parameter Time
[10…65535][s] [1…65535][min/h] appears to set the time period.
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
22
Password [Level 1: 1234; Level 2: 5678]: parameter made of four additional
textboxes, each of which should contain one of the four consecutive digits [0…9]
that will compose the password.
In case of enabling two security levels, the Password parameter will show twice,
being the first one referred to the password of Level 1, and the second one to the
password of Level 2.
Figure 8. Two security levels.
Important: the password insertion dialog features a specific option (lower left
button) that lets the user change, in runtime, the passwords originally set by
parameter. After accessing this option and prior to typing the new password, the
user will be required to type the corresponding old password (level 1 or level 2).
Note that although it will be possible to type password 2 even if the device asks
for password 1, the new password typed afterwards will be anyway stored as the
new password for level 1.
Security Pad Labels: parameter consisting in six additional textboxes, intended
for the customisation of the messages that the device shows (or may show) when
the user interacts with the password insertion dialog.
Label for ‘Enter Password 1’ [Enter Password 1]: message shown when
the user is required to type in the password for level 1.
Label for ‘Enter Password 2’ [Enter Password 2]: message shown when
the user is required to type in the password for level 2.
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
23
Label for ‘ERROR’ [ERROR]: message shown to the user when the typed
password is not valid.
Label for ‘New Password’ [New Password]: message shown to ask the
user for a new password, during the password change process.
Label for ‘Repeat Password’ [Repeat Password]: message shown when
the user is required to re-type the new password.
Label for ‘Updated’ [Updated]: message shown to the user as a
confirmation of the password change.
3.1.5 INTERNAL TEMPERATURE SENSOR
Z35 is equipped with an internal temperature sensor for monitoring the ambient
temperature of the room, so that the device can report it to the KNX bus and trigger
several actions when the temperature reaches certain values.
Please refer to the specific documentation of the “Temperature Probe” available at the
Zennio homepage, www.zennio.com, for detailed information about the functionality and
the configuration of the related parameters.
3.1.6 SCREENSAVER
The screensaver is a special page that will only be shown after a period of inactivity,
configurable by parameter.
Configuring the screensaver to only show the current Time, the current Temperature
(selecting the desired measurement source: the internal temperature sensor or an
external value) or both.
Figure 9. Screensaver Pop up.
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
24
There will also be an option to show an image on the screensaver. This image will be
loaded from a tab called DCA that will appear at the bottom of ETS. For more information
see section 3.1.6.1.
If the image and another screensaver option are enabled, both pages will alternate, each
of them being active during 15 seconds.
The screensaver will disappear when touching the screen screen or the HOME button
or, if the proximity sensor is activated, when it detects presence.
Notes:
When showing the welcome greeting (see section 3.1.10.2), screensaver will not
become active.
When screensaver will be active and a pop-up will be actived (see touch locking
3.1.8, cleaning function 3.1.10.1 or welcome greeting 3.1.10.2) this pop-up will
become show up over screesaver.
ETS PARAMETERISATION
After enabling “Screensaver” from “General” screen (see section 3.1.1), a new tab will
be incorporated into the tree on the left.
Figure 10. Screensaver.
Time/Date [disabled/enabled]: sets whether to show the current time or not.
Temperature [disabled/enabled]: sets whether to show the current temperature
or not. When enabled, it is possible to select the source of the temperature value
[Internal Temperature Probe/External Value]. The latter option will enable a new
two-byte object “[General] External Temperature” through which the device
can receive the required values from the bus.
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
25
Picture [disabled/enabled]: sets whether to show an image in the screensaver.
This image will be selected using the ETS App Axx Image Downloader (ver
section 3.1.6.1).
3.1.6.1 ZXX IMAGE DOWNLOADER
The ETS App Zxx Image Downloader offers the possibility to select a custom image to
be used as a screensaver in Z35. When installed, an additional tab called DCA will be
available.
Figure 11. Zxx Image Downloader tab
The dimensions of the image must be 320x240 pixels, being the supported formats:
.png, .jpg, .jpeg and .bmp.
When the chosen image met these conditions, a preview of it will be showed as well as
a message indicating that the image has been loaded correctly.
Figure 12. Preview of a correct image in the DCA
After a valid image has been loaded, it will be downloaded when programming from ETS.
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
26
3.1.7 AMBIENT LUMINOSITY SENSOR
Z35 includes a sensor to measure the ambient luminosity level, so that the brightness of
the display can be adjusted according to the current luminosity of the room.
Please refer to the specific manual “Luminosity and Proximity Sensor” (available in
the Z35 product section at the Zennio homepage, www.zennio.com) for detailed
information about the functionality and the configuration of the related parameters.
3.1.8 TOUCH LOCKING
The touch panel of Z35 can be optionally locked and unlocked anytime by writing a
configurable one-bit value to a specific object provided for this purpose. It can also be
done through scene values.
While locked, user presses on the touch buttons will be ignored: no actions will be
performed when the user presses on any of the controls. However, if configured, a
message will be shown on the display for three seconds if the user touches a button
during the lock state.
Figure 13. Touch Locking message.
Note: If an alarm with active lock is activated, it will be disabled and you can press the
screen normally. After confirming the alarm, the screen will be locked again.
ETS PARAMETERISATION
After enabling Touch Locking from “General” screen (see section 3.1.1), a new tab will
be incorporated into the tree on the left.
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
27
Figure 14. Touch Locking.
In this tab you can configure the blocking of the presses on the display.
1-Bit Object [disabled/enabled]: enables the 1-bit object “[General] Touch
Locking” to trigger the touch lock.
Value [0 = Unlock, 1 = Lock / 0 = Lock, 1 = Unlock]: parameter to select
which value should trigger which action when received through the indicated
object.
Scene Object [disabled/enabled]: enables the touch locking and unlocking when
receiving the configured scene value through the object (“[General] Scene:
receive”).
Lock: Scene Number (0 = Disabled) [0/1…64]: scene number that locks
the touch.
Unlock: Scene Number (0 = Disabled) [0/1…64]: scene number that
unlocks the touch.
Push Button Notification [Disabled/Display Message]: sets whether to display
a message on the screen or not when the device is locked and the user attempts
to touch a button. When the first one is selected, one textbox (Message) appears
to enter the desired message.
3.1.9 SOUNDS
Z35 emits 3 types of sounds, depending on the action performed:
Press Confirmation: short beep indicating that the user has pressed a button.
This only applies to step controls, i.e., controls that walk through a certain range
of values and that do not send a value after every touch, but only the final value
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
28
after the last press. For this action, the user can choose between two different
sounds.
Sending Confirmation: a slightly longer and sharper beep than the previous
one. It indicates the sending of an object to the bus as a result of a press.
Alarm: sharp and longer beep than the previous one, high intensity, which is
typically used as alarm or bell.
The range of sounds emitted when these actions are performing will be different
depending on the sound type selected.
Enabling and disabling the button sounds can be done in parameters or through an
object, being also possible to define in parameters whether the button sounds should be
initially enabled or not.
Pressing and sending confirmation sounds can be silenced using one of the following
methods:
Parameterisation after ETS download.
1-bit communication object.
Checkbox in "Configuration Page".
Note: Under no circumstances the alarm or the ring tone will be muted.
ETS PARAMETERISATION
After enabling the “Custom” configuration of Sounds from “General” screen (see section
3.1.1), a new tab will be incorporated into the tree on the left.
Figure 15. Sounds.
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
29
The initial configuration of this screen is equivalent to the default option. However, the
following parameters will be configurable.
Sound Type [Sound 1 / Sound 2]: sets which sounds range incorporates the
device.
Disable Button Sounds [disabled/enabled]: allows the user to ignore the push
and to confirm sounds.
Enable/Disable Button Sound Through a 1-bit Object [disabled/enabled]:
makes it possible to disable / resume the button beeping function in runtime
by writing to a specific object (“[General] Sounds – Disabling button
sound”).
Button Sound After ETS Download [enabled/disabled]: sets whether
the button beeping function should start up enabled (default option) or
disabled after an ETS download.
Value [0 = Disabled; 1 = Enabled / 0 = Enabled; 1 = Disabled]: parameter
to select which value should trigger which action when received through
the indicated object.
Object for Doorbell [disabled/enabled]: enables or disables the doorbell
function. If enabled, a specific object (“[General] Sounds: Doorbell”) will be
included into the project topology.
Value [0 = No Action; 1 = Doorbell/0 = Doorbell; 1 = No Action]: parameter
to select which value should trigger which action when received through the
indicated object
3.1.10 ADVANCED
Tab for the parameterisation of some advanced functions is shown in ETS if enabled
from the “Configuration” tab. These functions are explained next.
ETS PARAMETERISATION
After enabling the Advanced configuration from “General” screen (see section 3.1.1),
a new tab will be incorporated into the tree on the left.
Z35
http://www.zennio.com Tecnical Support: http://support.zennio.com
30
Figure 16. Advanced.
Cleaning Function [disabled/enabled]: enables or disables the “Cleaning
Function” tab. See section 3.1.10.1 for details.
Welcome Greeting [disabled/enabled]: enables or disables the “Welcome
Greeting” tab. See section 3.1.10.2 for details.
Welcome Back Object [disabled/enabled]: enables or disables the “Welcome
Back Object” tab. See section 3.1.10.3 for details.
Object to Change the Temperature Scale [disabled/enabled]: enables or
disables the 1-bit object “[General] Temperature Scale”), which permits
changing in runtime the scale of the temperatures that may show on the screen.
By receiving one ‘0’ through this object, the scale will switch to Celsius, while
after receiving one ‘1’ it will switch to Fahrenheit.
The selected scale applies to any temperatures shown on the screen, such as:
The screensaver temperatura.
Indicators of temperature controls linked to a box in the display ([Climate]
Temperature setpoint)
Temperature indicators ([Climate] Temperature).
Temperature shown on the thermostat page setpoint.
In this functionality, the following parameter will also appear:
Scale After Programming [Celsius (ºC) / Fahrenheit (ºF)]: sets the scale in
use after download.
Loading...