Zenith XBV322 OPERATING GUIDE

Installation and Operating Guide | Warranty

Model Number |XBV322|DVD Player + Video Cassette Recorder

Safety Precautions

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING: Do not install this equipment in a confined space such as a book case or similar unit.

NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

CAUTION:

This DVD+VCR employs a Laser System. To ensure proper use of this product, please read this owner’s

manual carefully and retain for future reference should the unit require maintenance, contact an authorized service location.

Use of controls, adjustments, or the performance of procedures other than those specified herein may result in hazardous radiation exposure.

To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.

CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

REGULATORY INFORMATION: FCC Part 15

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the product is operated in a residential installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.  Increase the separation between the product and

receiver.

 Connect the product into an outlet on a circuit different

from that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician

for help.

FCC COMPLIANCE: The responsible party for this product’s compliance is: Zenith Electronics Corporation, 2000 Millbrook Drive, Lincolnshire, IL 60069, USA Phone: 1-847-941-8000.

NOTES ON COPYRIGHTS:

It is forbidden by law to copy, broadcast, show, broadcast via cable, play in public, or rent copyrighted material without permission. This product uses copyright protection developed by Macrovision. Copy protection signals are recorded on some discs. When recording and playing the pictures of these discs on a VCR, picture noise will appear. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

SERIAL NUMBER: The serial number is found on the back of this unit. This number is unique to this unit and not available to others. You should record requested information here and retain this guide as a permanent record of your purchase.

Model No. _________________________________ Serial No. _________________________________

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

INTRODUCTION

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions. - All these safety and oper-

ating instructions should be read before the product is operated.

2. Keep these instructions. - The safety, operating and use instructions should be retained for future reference.

3. Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to.

4. Follow all instructions. - All operating and use instructions should be followed.

5. Do not use this product near water. – For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement; or near a swimming pool; and other areas located near water.

6. Clean only with dry cloth. – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. -

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over- heating. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. D

o not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the product.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with apparatus. When a cart is used, use caution when moving the cart/product combination to avoid injury from tip-over.

13. Unplug this product during lightning storms or when unused for long periods of time.

14.

Refer all servicing to qualified service personnel. Servicing is required when the product has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the product, the product has been exposed to rain or moisture, does not operate normally, or has been dropped.

CAUTION:

PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL. AND THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

This product has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for installation, use, and servicing. This product does not contain any parts that can be repaired by the user.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

Table of Contents

Introduction

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 2

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . 3

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . 6

About Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Selecting the Viewing Source. . . . . . . . . . . . . . . . 6

Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . 7

Display Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connections Panel . . . . . . . . . . . . . . . . . . . . . . . . 10

Preparation

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13

Connecting Antenna/Cable TV to DVD+VCR . . . 11

Basic TV Connections . . . . . . . . . . . . . . . . . . . . 12

Optional, Preferred TV Connections . . . . . . . 12-13

Before VCR Operation . . . . . . . . . . . . . . . . . . . 14-16

On-Screen Display(OSD) . . . . . . . . . . . . . . . . . . 14

On-Screen Menus Setup . . . . . . . . . . . . . . . . . . 14

Setting the VCR Setup Menu Options . . . . . . . . 15

Channel Selection . . . . . . . . . . . . . . . . . . . . . . . 15

Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . 16

Before DVD Operation . . . . . . . . . . . . . . . . . . . 17-20

General Explanation. . . . . . . . . . . . . . . . . . . . . . 17

On-Screen Display. . . . . . . . . . . . . . . . . . . . . . . 17

DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 18-20



General Operation . . . . . . . . . . . . . . . . . . . . 18



Language . . . . . . . . . . . . . . . . . . . . . . . . . . 18



Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18



Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19



Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19



Parental Control . . . . . . . . . . . . . . . . . . . . . . 20

Operation

Tape Operation . . . . . . . . . . . . . . . . . . . . . . . . . 21-26

Normal Playback . . . . . . . . . . . . . . . . . . . . . . . . 21

Special Effect Playbacks . . . . . . . . . . . . . . . . . . 21



Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21



Still Picture and Frame-by-Frame Playback . 21



Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . . 21



CM Skip (Commercial Skip) . . . . . . . . . . . . . 21



EZ (EASY) Review. . . . . . . . . . . . . . . . . . . . 21

Normal Recording . . . . . . . . . . . . . . . . . . . . . . . 22

Timer Recording . . . . . . . . . . . . . . . . . . . . . . 22-23

Instant Timer Recording . . . . . . . . . . . . . . . . . . . 24

Dubbing and Editing. . . . . . . . . . . . . . . . . . . . . . 24

Copying from DVD to VCR. . . . . . . . . . . . . . . . . 24

VHS Hi-Fi Stereo System/MTS Broadcast . . . . . 25

Tape Counter Memory Feature. . . . . . . . . . . . . . 26

Additional Information . . . . . . . . . . . . . . . . . . . . 26

DVD Operation . . . . . . . . . . . . . . . . . . . . . . . . . 27-29

Playing DVDs . . . . . . . . . . . . . . . . . . . . . . . . . . 27

General Features . . . . . . . . . . . . . . . . . . . . . . . . 27



Selecting other TITLEs. . . . . . . . . . . . . . . . . 27



Selecting other CHAPTERs . . . . . . . . . . . . . 27



Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . . 27



Still Picture and Frame-by-Frame Playback . 28



Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28



Random. . . . . . . . . . . . . . . . . . . . . . . . . . . . 28



Repeat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28



Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 28



Time Search . . . . . . . . . . . . . . . . . . . . . . . . 28



3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 28



Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28



Marker Search . . . . . . . . . . . . . . . . . . . . . . . 29

Special DVD Features . . . . . . . . . . . . . . . . . . . . 29



Checking the contents of DVD Video discs: Menus

. 29



Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 29



Disc Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 29



Camera Angle . . . . . . . . . . . . . . . . . . . . . . . 29



Changing the Audio Language . . . . . . . . . . . 29



Subtitles. . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Audio CD and MP3/WMA Disc Operation . . . . 30-31

Playing an Audio CD and MP3/WMA Disc . . . . . 30

MP3/WMA Recording Notes. . . . . . . . . . . . . . . . 30



Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31



Selecting other Tracks . . . . . . . . . . . . . . . . . 31



Repeat Track/ All/ Off . . . . . . . . . . . . . . . . . . 31



Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31



Random. . . . . . . . . . . . . . . . . . . . . . . . . . . . 31



Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 31



3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 31



Changing the Audio Channel . . . . . . . . . . . . 31

JPEG Files Operation . . . . . . . . . . . . . . . . . . . . . . 32

Viewing JPEG files. . . . . . . . . . . . . . . . . . . . . . . 32



Selecting other Files . . . . . . . . . . . . . . . . . . 32



Still Picture . . . . . . . . . . . . . . . . . . . . . . . . . 32



To flip the picture . . . . . . . . . . . . . . . . . . . . . 32



To rotate picture . . . . . . . . . . . . . . . . . . . . . . 32



Notes on JPEG Files . . . . . . . . . . . . . . . . . . 32

Programmed Playback . . . . . . . . . . . . . . . . . . . . . 33

Programmed Playback with Audio CDs and

MP3/ WMA Discs . . . . . . . . . . . . . . . . . . . . . . . . 33



Repeat Programmed Tracks/ All/ Off . . . . . . 33



Erasing a Track from Program List . . . . . . . . 33



Erasing the Complete Program List . . . . . . . 33

Reference

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 34-35

Language Code List . . . . . . . . . . . . . . . . . . . . . . . 36

Country Code List . . . . . . . . . . . . . . . . . . . . . . . . . 37

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

About the symbols for instructions

Indicates hazards likely to cause harm to the unit itself or other material damage.

Indicates special operating features of this unit.

Indicates tips and hints for making the task easier.

INTRODUCTION

Before Use

Playable Discs

DVD (8 cm/12 cm disc)

Audio CD (8 cm/12 cm disc)

In addition, this unit can play a CD-Rs or CD-RWs that contain audio titles, MP3, JPEG, or WMA files.

otes

– Depending on the conditions of the recording

equipment or the CD-R/RW disc itself, some CD-R/RW discs cannot be played on the unit.

– The unit cannot play discs that contain data other

than MP3 and CD-DA data.

– Do not attach any seal or label to either side

(the labeled side or the recorded side) of a disc.

– Do not use irregularly shaped CDs

(e.g., heart-shaped or octagonal). The unit may malfunction.

otes on DVDs

Some playback operations of DVDs may be intentionally fixed by software manufacturers. As this unit plays DVDs according to disc content designed by the software manufacturer, some playback features of the unit may not be available or other functions may be added. Refer also to the instructions supplied with the DVDs. Some DVDs made for business purposes may not be played on the unit.

Regional code of this DVD+VCR and DVDs

This DVD+VCR is designed and manufactured for playback of Region 1 encoded DVD software. The region code on the labels of some DVD discs indicate which type of DVD+VCR can play those discs. This unit can play only DVD discs labeled 1 or ALL. If you try to play any other discs, the message “Check Regional Code” will appear on the TV screen. Some DVD discs may not have a region code label even though their playback is prohibited by area limits.

ote on DTS-encoded CDs

When playing DTS-encoded CDs, excessive noise may be exhibited from the analog stereo output. To avoid possible damage to the audio system, turn down the volume before playing back such discs, adjust the volume gradually, and keep the volume level low. To enjoy DTS Digital Surround

playback, an external 5.1 channel Digital SurroundTMdecoder system must be connected to the digital output of the unit.

Disc-related Terms

Title (DVD only)

The main film content or accompanying feature content or music album. Each title is assigned a title reference number enabling you to locate it easily.

Chapter (DVD only)

Sections of a picture or a musical piece that are smaller than titles. A title is composed of one or several chapters. Each chapter is assigned a chapter number to enable you to locate the chapter you want. Depending on the disc, chapters may not be recorded.

Track (audio CD only)

Sections of a musical piece on an audio CD. Each track is assigned a track number, enabling you to locate the track you want.

Remote Control Battery Installation

Detach the battery cover on the rear of the remote control, and insert two R03 (size AAA) batteries with and aligned correctly.

Caution

Do not mix old and new batteries. Never mix different types of batteries (standard, alkaline, etc.).

Remote Control Operating Range

Point the remote control at the remote sensor and press the buttons.



Distance: About 23 ft (7 m) from the front of the remote sensor



Angle: About 30° in each direction of the front of the remote sensor

IMPORTANT NOTE:

SPENT OR DISCHARGED BATTERIES MUST BE RECYCLED OR DISPOSED OF IN A SAFE MANNER IN COMPLIANCE WITH ALL APPLICABLE LAWS. FOR DETAILED INFORMATION, CONTACT YOUR LOCAL COUNTY SOLID WASTE AUTHORITY.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. Confidential unpublished works. Copyright 1992-1997 Dolby Laboratories. All rights reserved.

DTS and DTS Digital Out are trademarks of Digital Theater Systems, Inc.

AAA

Before Use (Continued)

Precautions

Handling the unit

When shipping the unit

The original shipping carton and packing materials come in handy. For maximum protection, re-pack the unit as it was originally packaged at the factory.

When setting up the unit

The picture and sound of a nearby TV, VCR, or radio may be distorted during playback. In this case, position the unit away from the TV, VCR, or radio, or turn off the unit after removing the disc.

To keep the surface clean

Do not use volatile liquids, such as insecticide spray, near the unit. Do not leave rubber or plastic products in contact with the unit for a long period of time. They will leave marks on the surface.

Cleaning the unit

To clean the cabinet

Use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit.

To obtain a clear picture

The DVD+VCR is a high-tech, precision device. If the optical pick-up lens and disc drive parts are dirty or worn, the picture quality will be poor. Regular inspection and maintenance are recommended after every 1,000 hours of use. (This depends on the operating environment.) For details, please contact your nearest dealer.

Notes on Discs

Handling discs

Do not touch the playback side of the disc. Hold the disc by the edges so that fingerprints will not get on the surface. Do not stick paper or tape on the disc.

Storing discs

After playing, store the disc in its case. Do not expose the disc to direct sunlight or sources of heat, or leave it in a parked car exposed to direct sunlight, as there may be a considerable temperature increase inside the car.

Cleaning discs

Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the disc from the center out.

Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static spray intended for older vinyl records.

About Symbols

About the symbol display

“ ” may appear on the TV screen during operation. This icon means the function explained in this owner’s manual is not available at that moment or with that specific DVD.

About the disc symbols for instructions

A section whose title has one of the following symbols are applicable only to those discs represented by the symbol.

DVD Audio CDs. MP3 Discs. WMA Discs. JPEG Files.

JPEG

WMA

MP3

DVD

Yes

Selecting the Viewing Source

You must select one of your output sources (DVD or VCR) to view on the TV screen.

• If you want to view DVD deck output source:

Press DVD on the remote or DVD/VCR on the front panel until DVD indicator in the display window lights and output source of DVD deck is viewed on the TV screen.

• If you want to view VCR deck output source:

Press VCR on the remote or DVD/VCR on the front panel until VCR indicator in the display window lights and output source of VCR deck is viewed on the TV screen.

otes

• If you insert a disc while the DVD+VCR is in the VCR

mode, the DVD+VCR will switch to DVD mode automatically.

• If you insert a cassette tape without an erasure pre-

vention tab intact while the DVD+VCR is in the DVD mode, the DVD+VCR will switch to VCR mode automatically.

INTRODUCTION

Front Panel Controls

PAUSE/STEP(XX/CC)

Pause playback of a tape or a disc in the DVD or VCR deck temporarily/press repeatedly for frame-by-frame playback.

OPEN/CLOSE (ZZ)

Opens or closes the disc tray.

Remote Sensor

Point the DVD+VCR remote control here.

Display window

Shows the current status of the DVD+VCR.

Disc Tray (DVD deck)

Insert a disc here.

POWER

Switches the DVD+VCR ON and OFF.

DVD/VCR (output select)

Select one of your output sources to

view on the TV screen between DVD

and VCR.

REC/ITR (zz)

To record normally or to activate Instant Timer Recording.

CH (vv/VV)

To scan up or down through memorized channels.

STOP (xx)

Stops playback of a disc or tape.

LINE 2 (VIDEO IN/AUDIO IN (Left/Right))

Connect the audio/video output of an

external source (Audio system,

TV/Monitor, another VCR).

Cassette Compartment (VCR deck)

Insert a video cassette here.

EJECT(ZZ)

Ejects the tape in the VCR deck.

COPY

Press to copy a DVD in the DVD deck to a VHS tape in the VCR deck.

PLAY

To play back a recorded tape or disc.

Forward SKIP/SCAN DVD: Go to NEXT chapter/track. Press and hold for

two seconds for a fast forward search. VCR: Advances the tape during the STOP mode or for fast picture search. Fast Forward will work in the Stop or Play modes.

Reverse SKIP/SCAN DVD: Go to beginning of current chapter/track or to previous

chapter/track. Press and hold for a fast reverse search.

VCR:

Rewinds the tape during the STOP mode or for fast reverse picture search.

Reverse will work in the Stop or Play modes.

Display Window

DVD+VCR is in VCR timer recording mode or a VCR timer recording is programmed.

A cassette is loaded in the VCR deck.

VCR deck is selected.

DVD+VCR is Recording a tape.

Indicates PM time. (AM is not displayed.)

Lights when TV mode is active (See page 22.)

A disc is loaded in the DVD deck. (Lights when a disc is loaded in the DVD deck

and flashes when no disc is loaded.)

Indicates repeat mode.

DVD to VCR copy is in progress.

Indicates total playing time, elapsed time, remaining time or current deck status (Playback, Pause, etc).

DVD deck is selected.

DVD

COPY

VCR REC

INTRODUCTION

Remote Control

DVD/VCR select button

Select the output source (DVD or VCR)

to view on the TV screen.

POWER

Switches DVD+VCR ON and OFF.

TV/VCR

To view channels selected by the VCR

tuner or by the TV tuner.

DISPLAY, CLK/CNT

Accesses On-Screen display.

Switches among the clock, tape counter

and tape remaining modes on the display.

b/B/v/V (left/right/up/down)

- Selects an option in the menu

v/V: Selects VCR channels. Manually

adjusts the tape’s picture onscreen.

SETUP, MENU

Accesses or removes DVD Setup menu

and VCR menu.

TITLE



Displays the disc’s Title menu, if

available.

PAUSE/STEP (XX)



Pause playback or recording

temporarily/press repeatedly for frame-

by-frame playback.

STOP (xx)



Stops playback.

REC/ITR (zz)



Records normally or activates Instant

Timer Recording.

0-9 numerical buttons

Selects numbered options in a menu.

AUDIO



Selects an audio language (DVD) or an

audio channel (CD).

SUBTITLE



Selects a subtitle language.

MARKER



Marks any point during playback.



Displays MARKER SEARCH menu.

REPEAT, EZ review



Repeat chapter, track, title, all.

Replays the specified segment twice.

RANDOM, CM Skip



- Plays tracks in random order.

- Fast forwards picture search through

30 seconds of recording.

A-B, SP/SLP



- Repeats sequence.

- Selects recording speed

OPEN/CLOSE, EJECT (ZZ)

- Opens and closes the disc tray.

- Ejects the tape in the VCR deck.

SELECT/ENTER

- Acknowledges menu selection.

- Displays functions on the TV screen.

INPUT

To select the VCR deck’s source (Tuner, LINE 1, or LINE 2).

DISC MENU

Accesses menu on a DVD disc.

RETURN

Removes the Setup menu.



FORWARD (>>)

DVD: Search forward*/go to next chapter or track. VCR: Advances the tape in STOP mode or for fast forward picture search.

* Press and hold button for about two seconds.



PLAY (HH)

Starts playback.



BACKWARD (..)

DVD: Search backward*/go to beginning of current chapter or track or go to previous chapter or track. VCR: Rewinds the tape in STOP mode or for fast reverse picture search.

* Press and hold button for about two

seconds.

PROGRAM

Accesses or removes Program menu.

CLEAR

Removes a track number on the program menu or a mark on the MARKER SEARCH menu.



ANGLE

Selects a DVD camera angle if available.



ZOOM

Enlarges DVD video image.

ote

This remote control use the same buttons for VCR and DVD functions (ex. PLAY). To use the VCR, first press the VCR button. To use the DVD, first press the DVD button.

Connections Panel

Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit.

VCR IN LINE 1

(VIDEO IN/AUDIO IN (Left/Right))

Connect the audio/video output of an external

source (Audio system, TV/Monitor,

another VCR).

ANTENNA INPUT

Connect the VHF/UHF/CATV antenna to this terminal.

DVD/VCR OUT (VIDEO/AUDIO (Left/Right))

Connect to a TV with video and audio inputs.

AUDIO OUT (Left/Right) (DVD OUT)

Connect to a TV, amplifier, receiver, or stereo system.

DIGITAL AUDIO OUT (COAXIAL) (DVD OUT)

Connect to digital (coaxial) audio equipment.

AC Power Cord

Plug into the power source.

S-VIDEO OUT (DVD OUT)

Connect to a S-Video Input on TV.

COMPONENT VIDEO OUT (Y Pb Pr) (DVD OUT) Connect to a TV with Y Pb Pr inputs.

RF. OUT(DVD/VCR OUT)

Connect to a TV with RF coaxial inputs.

PREPARATION

Connections

ips



Depending on your TV and other equipment you wish to connect, there are various ways you could connect the DVD+VCR. Use connections described on pages 11-13.



Please refer to the manuals of your TV, VCR, Stereo System or other devices as necessary to make the best connections.



For better sound reproduction, connect the DVD+VCR’s DVD/VCR AUDIO OUT jack to the audio in jacks of your amplifier, receiver, stereo or audio/video equipment. See Optional, Preferred TV Connections on pages 12-13.

Caution



Make sure the DVD+VCR is connected directly to the TV. Tune the TV to the correct video input channel.



Do not connect the DVD+VCR’s DVD/VCR AUDIO OUT jack to the phono in jack (record deck) of your audio system.



Do not connect your DVD+VCR via your VCR. The DVD image could be distorted by the copy protection system.

Connecting Antenna/Cable TV to DVD+VCR

Disconnect the antenna leads from the rear of the TV.

Identify the type of cable from your antenna. If it is a round cable as illustrated, it is a 75 ohm coaxial antenna cable. This cable will connect directly to the jack marked ANT.IN on your DVD+VCR.

If your antenna lead wire is a flat type antenna cable, connect it to a Antenna Adapter (300-ohm to 75-ohm) (not supplied) and slip the Adapter onto the ANT.IN jack. The Adapter does not screw on to the DVD+VCR, it just slips over the jack.

Without Cable Box

If your cable wire is connected to your TV without a converter or descrambler box, unscrew the wire from your TV and attach it to the ANT.IN jack on the DVD+VCR. Use the supplied round coaxial cable to connect between the DVD+VCR’s RF.OUT jack and the 75 ohm antenna input jack on the TV. With this connection, you can receive all midband, super band, and hyperband channels.

With Cable Box

If a converter is required in your cable system, follow the instruction below: The cable hookup permits both TV and DVD+VCR operation.

To view or record CATV channel 1 Tune the TV to the DVD+VCR output channel (CH 3 or 4). 2 Set the DVD+VCR channel selector to the output channel of

the Cable Converter box by using the CH (v/V)or number (0-9) of your DVD+VCR. (Example: CH3)

3 Select the channel to view at the Cable Converter Box.

otes

 With this connection, you CANNOT record one program

while viewing another.

 If you are using a cable box to tune channels, it is not nec-

essary to do Auto Channel Programming as indicated on page 15.

Cable TV

Wall Jack

Back Panel of

Typical Cable Box

Antenna Antenna

Cable TV

Wall Jack

Flat Wire

(300 ohm)

300/75 ohm

Adapter

(Not supplied)

OR OR

Rear of DVD+VCR

Connections (Continued)

Basic TV Connections



Make one of the following connections, depending on the capabilities of your existing equipment.

RF coaxial connection

Connect the RF.OUT jack on the DVD+VCR to the antenna in jack on the TV using the 75-ohm Coaxial Cable supplied (R).

ote

If you use this connection, tune the TV to the DVD+VCR’s RF output channel (CH 3 or 4).

How to set the DVD+VCR’s RF output channel

1. While the DVD+VCR is turned off,

press and hold CH

(v/V) on the front panel for about five seconds.

The unit will turn itself on and “RF 03” or “RF 04” appears in the display window.

Use CH (v/V) on the front panel or v/V on the remote control to change the RF output channel (CH 03 or CH 04).

Turn off and on the DVD+VCR.

Audio/Video connection

Connect the DVD/VCR VIDEO OUT jack on the DVD+VCR to the video in jack on the TV using the video cable supplied (V).

Connect the Left and Right DVD/VCR AUDIO OUT jacks on the DVD+VCR to the audio left/right in jacks on the TV (A1) using the supplied audio cables.

ote

If you use this connection, set the TV’s source selector to VIDEO.

Optional, Preferred TV Connections

otes

 You can watch and listen ONLY to DVD playback

through the connections shown below.

S-Video connection

Connect the S-VIDEO OUT jack on the DVD+VCR to the S-Video in jack on the TV using an optional S-Video cable (S).

Connect the Left and Right AUDIO OUT jacks of the DVD+VCR to the audio left/right in jacks on the TV using the supplied audio cables (A2).

Component Video (Color Stream®) connection

Connect the COMPONENT VIDEO OUT jacks on the DVD+VCR to the corresponding in jacks on the TV using an optional Y Pb Pr cable (C).

Connect the Left and Right AUDIO OUT jacks of the DVD+VCR to the audio left/right in jacks on the TV (A2) using the supplied audio cables.

Rear of TV

S-VIDEO

INPUT

S A2C

COMPONENT VIDEO INPUT

AUDIO INPUT

Rear of TV

ANTENNA

INPUT

Rear of DVD+VCR

AUDIO INPUT

A1 VR

VIDEO

INPUT

Rear of DVD+VCR

PREPARATION

Connections (Continued)

Optional, Preferred TV Connections

ote

You can listen to ONLY DVD playback using COAXIAL (X) and AUDIO OUT (A2) connections. The tuner and VCR will still be heard through the RF.OUT (R) or DVD/VCR AUDIO OUT (A1) jack. (See page 12.)

Connecting to an amplifier equipped with two channel analog stereo or Dolby Surround

Connect the Left and Right AUDIO OUT (or DVD/VCR AUDIO OUT) jacks on the DVD+VCR to the audio left and right in jacks on your amplifier, receiver, or stereo system using the audio cables (for A1 or A2 connec-

tion) supplied.

Connecting to an amplifier equipped with two channel digital stereo (PCM) or to an Audio/Video receiver equipped with a multi-channel decoder (Dolby Digital™, MPEG 2, or DTS)

Connect one of the DVD+VCR’s DIGITAL AUDIO OUT jacks (COAXIAL X) to the corresponding in jack on your amplifier. Use an optional digital (coaxial X) audio cable.

You will need to activate the DVD+VCR’s digital output. (See “Digital Audio Output” on page 19).

Digital Multi-channel sound

A digital multi-channel connection provides the best sound quality. For this you need a multi-channel Audio/Video receiver that supports one or more of the audio formats supported by your DVD+VCR (MPEG 2, Dolby Digital and DTS). Check the receiver manual and the logos on the front of the receiver.

Caution:

Due to the DTS Licensing agreement, the digital output will be in DTS digital out when DTS audio stream is selected.

otes

–

If the audio format of the digital output does not match the capabilities of your receiver, the receiver will produce a strong, distorted sound or no sound at all.

– Six Channel Digital Surround Sound via digital con-

nection can only be obtained if your receiver is equipped with a Digital Multi-channel decoder.

– To see the audio format of the current DVD in the on-

screen display, press AUDIO.

Accessory Audio/Video (A/V) Connections to DVD+VCR

Connect the VCR IN LINE 1 or LINE2 jacks on the DVD+VCR to the audio/video out jacks on your accessory component, using the optional audio/video cables.

Rear of DVD+VCR

A2A1 X

AUDIO INPUT DIGITAL INPUT

COAXIAL

Amplifier (Receiver)

Jack Panel of Accessory

AUDIO

OUTPUT

VIDEO

OUTPUT

Rear of DVD+VCR Front of DVD+VCR

On-Screen Display (OSD)

Some of these functions will be displayed every time the VCR is operated.

❶❷ ❸ ❹ ❺

❻❼

❶ TAPE SPEED DISPLAY

Shows the current tape speed.

❷ FUNCTION DISPLAY

Indicates the function in progress.

❸ HI-FI DISPLAY

Indicates when this unit is playing back tape recorded with Hi-Fi.

❹ CHANNEL DISPLAY

ndicates the selected channel (or LINE1, LINE2).

❺ STEREO/SAP DISPLAY (MONO is not displayed)

Shows the type of audio signal received by the VCR tuner.

❻ DATE DISPLAY

Shows the current date. (Month/Date/Day of the week format)

❼ CLOCK/COUNT/REMAIN DISPLAY

Shows the current time, the tape counter and remaining time on the tape.

Each press of the SELECT/ENTER changes the TV on-screen displays in the following sequence.

otes

 The function displays remain on the TV screen for 5

seconds.

 The clock (or tape counter, tape remaining) mode will contin-

ue until you press SELECT/ENTER.

 The tape counter and the remaining tape length indicator

appear only when a cassette is inserted. Also, the remaining tape length indicator appears after any tape operation.

EASY INFORMATION

If the Extended Data Service (XDS) signals are provided along with normal TV signal in your area or during playback of a tape recorded with Extended Data Service (XDS) signals, the station ID, program title, and program details are shown on the TV screen. When viewing a channel with Extended Data Service (XDS) signals, press SELECT/ENTER and the station ID will appear on the TV screen. Press SELECT/ENTER again and the program details will appear on the TV screen. When viewing a tape recorded with Extended Data Service (XDS) signals, press SELECT/ENTER twice and the program title and program details will appear on the TV screen.

PROGRAM DETAILS LENGTH: Indicates the run length of a program. TIME REMAINING: Indicates the remaining time of a

program. RATING: Indicates the rating of the current program (N/A, G, PG, PG-13, R, NC-17, X and Not Rated). The rating N/A means that the motion picture ratings are not applicable to this program.

On-Screen Menus Setup

The SETUP, clock setting (CLOCK), and timer recordings (PROGRAM) are accessed conveniently with the on-screen menus, that lead you through each step. The following pages describe the on-screen menu selections available.

Menu Selection

Your VCR allows remote control adjustment of several features.

Press MENU and the MAIN menu will appear.

Select the desired menu with v/V button and then press SELECT/ENTER.

ote

Menus remain on-screen for 3 minutes.

Press MENU when finished.

Before VCR Operation

PLAY HI-FI CH 4 SP STEREO

JUL 5 , SAT 2:15 PM

REM 1:58

0:35:40

2:15 PM

STOP CH 4 SP STEREO

JUL 5 , SAT 2:15 PM

Easy Information Screen

(Program details)

Easy Information Screen

(Station ID)

CH 4

SP WABC STEREO

“Home video” JUL 5 , SAT 2:15 PM

PROGRAM DETAILS

“Home video”

LENGTH 01:00

TIME REMAINING 00:26

RATING N/A

CLOCK SET (page 16) PROGRAM (page 22) TUNING (page 15) SETUP (page 15)

MAIN MENU

PREPARATION

Before VCR Operation (Continued)

Setting the VCR Setup Menu Options

Press MENU and the MAIN menu will appear.

Use vv/VVto select the SETUP menu, then press SELECT/ENTER.

The SETUP menu will appear.

Use vv/VVto choose a desired option on the SETUP menu. Then use bb/BBto choose a

desired setting.

FUNCTION OSD

The on-screen display of this DVD+VCR can be turned on or off.

 FUNCTION OSD can be switched between ON and OFF by

using b/B.

LANGUAGE SELECT

The on-screen programming of this DVD+VCR can be displayed in either English, Spanish, or French.

 LANGUAGE SELECT can be switched among ENGLISH,

SPANISH and FRENCH by using b/B.

AUDIO MODE

The DVD+VCR has two separate audio playback systems, the high quality VHS Hi-Fi system and standard NORMAL mono system. The same audio is generally recorded on both systems. The VHS Hi-Fi system plays on separate (left and right) channels, and the NORMAL system plays monaural sound. The normal track is always played so the cassette can be played on a DVD+VCR that does not have VHS Hi-Fi.

 AUDIO MODE can be switched between HI-FI and

NORMAL by using b/B.

BROADCAST TYPE (STEREO/SAP/MONO)

Multichannel Television Sound (MTS) carries stereo and/or Second Audio Program (SAP) bilingual signals. Set this display to the desired position when both MTS stereo and SAP signals are received. When only one of the MTS signal is received, the DVD+VCR automatically selects the corresponding receiving mode (Stereo or SAP) regardless of the selected position. For normal operation, the display should be in the STEREO position. The DVD+VCR will then record a STEREO program when available, and record a mono program IF the program is NOT IN STEREO. For weak STEREO and/or SAP broadcasts, changing the display to mono may give clearer sound.

 BROADCAST TYPE can be switched among STEREO, SAP,

and MONO by using b/B.

AUDIO OUTPUT (STEREO/LEFT/RIGHT)

Used during playback [when AUDIO MODE (HI-FI/NORMAL) is in HI-FI position] for selecting the audio output signals from the AUDIO OUT terminals (L ch and R ch), and RF.OUT. This display setting should normally be left in the stereo position, so that when a stereo tape is played, the stereo sound will be heard through the left and right channels. If a mono tape is played and the audio output is set to stereo, the same mono sound will be heard from both left and right channels.

 AUDIO OUTPUT can be switched among STEREO, LEFT,

and RIGHT by using b/B.

Press MENU when finished.

Channel Selection

This DVD+VCR is equipped with a frequency synthesized tuner capable of receiving up to 181 channels. These include VHF channels 2-13, UHF channels 14-69 and CATV channels 1-125.

Preparation:



Connect the DVD+VCR to the desired type of antenna or cable TV system, as shown in Connecting Antenna/Cable TV to DVD+VCR on page 11.

AUTO CHANNEL PROGRAMMING

Press MENU and the MAIN menu will appear.

Use vv/VVto select the TUNING menu, then press SELECT/ENTER.

The TUNING menu will appear.

Use VVto choose the SOURCE SELECT option, then use bb/BBto select TUNER.

Press b/B repeatedly to switch between TUNER, LINE1 and LINE2.

Use vv/VVto choose the AUTO CHANNEL SET option, then use bb/BBto set the channel.

The tuner will automatically cycle through all available channels in the area and place them in the tuner’s memory.

After the AUTO CHANNEL SET has found all the available channels, set the TUNING BAND on the Tuning Menu, Choose TV or CATV using the

bb/BB

arrows.

Press MENU to return to the TV screen.

Use vv/VVor CH (vv/VV) on the front panel to cycle the DVD+VCR through the channels in memory.

TO ADD OR ERASE CHANNELS FROM MEMORY

This feature allows you to add or erase channels from memory manually.

1 Press VVto choose the CH. ADD/DEL option on the

TUNING menu. Using b/B to select a channel to add or erase.

2 Press SELECT/ENTER to add or erase the channel.

Repeat steps 1 and 2 to add or erase channels.

3 Press MENU to return to the TV screen.

Before VCR Operation (Continued)

Setting the Clock

The DVD+VCR gives you two ways to set the time and date: the Auto Clock Feature or manually. The Auto Clock feature enables the DVD+VCR to set up the clock while the DVD+VCR is turned off.

Auto Clock Set

The Auto Clock Set feature is set to ON at the factory. In the ON setting, the DVD+VCR looks for a channel carrying XDS (Extended Data Services) information. XDS updates the clock using the Coordinated Universal Time.

The Auto Clock feature enables the DVD+VCR to set up the clock when the DVD+VCR is turned off.

Press MENU and the MAIN menu will appear.

Use vv/VVto choose the CLOCK menu. Press SELECT/ENTER and the CLOCK menu will appear.

UseVVto choose the AUTO CLOCK SET option. Use bb/BBto choose ON.

Use EEto choose the DAYLIGHT SAVINGS option. Use

or GGto choose AUTO, ON or OFF.

If you choose AUTO, the VCR sets the clock using the DST information broadcast in the signal (channel). If you choose ON, the VCR sets the clock when the Daylight Saving Time is started and ended.

Use EEto choose the TIME ZONE item. Use

or GGto choose the correct time zone (AUTO, EASTERN, CENTRAL, MOUNTAIN, PACIFIC, ALASKA or HAWAII).

If “AUTO” is selected as the time zone, the VCR sets the clock using the first Coordinated Universal Time information it finds in a broadcast signal.

Use MENU when finished.

Turn off the DVD+VCR and the auto clock set feature sets the time.

ote

There are cases where the TV station does not send or sends wrong date and/or time information and the DVD+VCR sets the incorrect time. If this happens we recommend that you set the clock manually.

Manual Clock Set

Press MENU and the MAIN menu will appear.

Use vv/VVto choose the CLOCK menu. Press SELECT/ENTER and the CLOCK menu will appear.

Use bb/BBto choose the month.

Use VVto choose the DAY option. Use bb/BBto choose the date.

The day of the week will display automatically.

Use VVto choose the YEAR option. Use bb/BBto choose the year.

Use VVto choose the TIME option. Use bb/BBto choose the time. Press and hold b/B to advance clock

continuously.

Use EEto choose the DAYLIGHT SAVINGS item. Use

or GGto choose AUTO, ON or OFF.

If you choose AUTO, the VCR sets the clock using the DST information broadcast in the signal (channel). If you choose ON, the VCR adjusts the clock for Daylight Saving Time.

Press MENU when finished.

ote

If setting the clock manually, “AUTO CLOCK SET” must set to “OFF”. If set to “ON”, an incorrect date and/or time will be entered again when the DVD+VCR is turned off.



The clock uses the 12-hour system. (Be sure to set AM and PM correctly.) (AM does not appear.)



The initial Clock Setting is JANUARY 1, 2003, 12:00 AM.

Things to know before starting

Before DVD Operation

PREPARATION

General Explanation

This manual gives the basic instructions for operating the DVD+VCR. Some DVDs require specific operation or allow only limited operation during playback. When this occurs, the symbol appears on the TV screen, indicating that the operation is not permitted by the DVD+VCR or is not available on the disc.

On-Screen Display

The general playback status can be displayed on the TV screen. Some options can be changed on the menu.

On-screen display operation

Press DISPLAY during playback.

Use vv/VVto select an option.

The selected option will be highlighted.

Use bb/BBto change the setting of an option.

The number buttons can be also be used for setting numbers (e.g., title number). For some functions, press SELECT/ENTER to execute the setting.

Temporary Feedback Field Icons

Repeat Title (DVD) Repeat Chapter (DVD) Repeat A-B Repeat Off Resume play from this point Action prohibited or not available

otes

 Some discs may not provide all of the features on the

on-screen display example shown below.

 If no button is pressed for 10 seconds, the on-screen

display disappears.

Options

Title Number

Chapter Number

Time search

Audio language and Digital Audio Output mode

Subtitle language

Angle

Sound

Function (Use

vv/VV

to select desired option)

Shows the current title number and total number of titles, and skips to the desired title number.

Shows the current chapter number and total number of chapters, and skips to the desired chapter number.

Shows the elapsed playing time, and

searches the point by the elapsed time directly.

Shows the current audio soundtrack language, encoding method, and channel number, and

changes the setting.

Shows the current subtitles language, and

changes the setting.

Shows the current angle number and total number of angles, and changes the angle number.

Shows the current sound mode, and

changes the setting.

Selection Method

bb/BB

,or

Numeric, SELECT/ENTER

bb/BB

,or

Numeric, SELECT/ENTER

bb/BB

, AUDIO

bb/BB

, SUBTITLE

bb/BB

, ANGLE

bb/BB

1/3

1/12

0:16:57

1 ENG

5.1CH

OFF

1/1

NORM.

ABC

DVD

TITLE

CHAPT

A B

OFF

Before DVD Operation (Continued)

DVD Setup

You can set your personal preferences on the DVD+VCR.

General Operation

Press SETUP.

The Setup menu appears.

Use vv/VVto select the desired option.

The screen will show the current setting for the selected option, as well as alternate setting(s).

While the desired option is selected, use BB, then vv/VVto select the desired setting.

Press SELECT/ENTER to confirm your selection.

Some options require additional steps.

Press SETUP, RETURN, or PLAY (HH) to exit the Setup menu.

Language

Disc Language

Select a language for the disc’s: Menu, Audio, and Subtitle.

riginal : The original language set for the disc is selected.

Other : To select another language, use number buttons to

enter the corresponding 4-digit number according to the language code list on page 36. If you enter the wrong language code, press CLEAR.

ote

Disc Language selection is not available on some DVDs.

Menu Language

Select a language for the Setup menu. This is the menu you see when you press SETUP.

Picture

TV Aspect

4:3 Letterbox: Select when a standard 4:3 TV is con-

nected. Displays the picture with masking bars above and below the picture. 4:3 Panscan: Select when a standard 4:3 TV is connected. Displays the picture cropped to fill your TV screen. Both sides of the picture are cut off.

16:9 Wide: Select when a 16:9 wide TV is connected.

DVD

Disc Audio

Disc Subtitle

Disc Menu

Rating

Country Code

TV Aspect

Menu Language

Digital Audio Output

5.1 Speaker Setup

Others

Original

English

French

German

Spanish

Italian

Chinese

Polish

Hungarian

Other — — — —

Disc Audio

Disc Subtitle

Disc Menu

Rating

Country Code

TV Aspect

Menu Language

Digital Audio Output

5.1 Speaker Setup

Others

English

Spanish

French

Disc Audio

Disc Subtitle

Disc Menu

Rating

Country Code

TV Aspect

Menu Language

Digital Audio Output

5.1 Speaker Setup

Others

4:3 Letterbox

4:3 Panscan

16:9 Wide

Disc Audio

Disc Subtitle

Disc Menu

Rating

Country Code

TV Aspect

Menu Language

Digital Audio Output

5.1 Speaker Setup

Others

Original

English

French

German

Spanish

Italian

Chinese

Polish

Hungarian

Other — — — —

PREPARATION

Before DVD Operation (Continued)

Sound

Digital Audio Output

Each DVD disc has a variety of audio output options. Set the DVD+VCR’s Digital Audio Output according to the type of audio system you use. DOLBY DIGITAL/PCM: Select DOLBY DIGITAL/PCM if you have connected the DVD+VCR’s DIGITAL AUDIO OUT jack to a Dolby Digital decoder (or an amplifier or other equipment with a Dolby Digital decoder). Stream/PCM: Select Stream/PCM if you have connected the DVD+VCR’s DIGITAL AUDIO OUT jack to an amplifier or other equipment with a DTS decoder, Dolby Digital decoder or MPEG decoder. PCM: Select when connected to a 2 channel digital stereo amplifier. The DVD+VCR outputs sounds in the PCM 2ch format when you play a DVD video disc recorded with a Dolby Digital, MPEG1, or MPEG2 recording system.

Sample Frequency

To change the Sample Frequency setting, first select the desired Digital Audio Output as indicated above. If your receiver or amplifier is NOT capable of handling 96KHz signals, select 48KHz. When this choice is made, this unit will automatically convert any 96KHz signals to 48KHz so your system can decode them. If your receiver or amplifier is capable of handling 96KHz signals, select 96KHz. When this choice is made, this unit will pass each type of signal through without any further processing.

Others

The DRC, Vocal and Auto Play settings can be changed.

 Use v/V to select the desired option and press

SELECT/ENTER. The options can be turned On or Off.

Dynamic Range Control (DRC)

With the DVD format, you can hear a program’s soundtrack in the most accurate and realistic presentation possible, thanks to digital audio technology. However, you may wish to compress the dynamic range of the audio output (the difference between the loudest sounds and the quietest ones). Then, you may listen to a movie at a lower volume without losing clarity of sound. Set DRC to On for this effect.

Vocal

Set Vocal to On only when a multi-channel karaoke DVD is playing. The karaoke channels on the disc will mix into normal stereo sound.

Auto Play

You can set up the DVD Player so a DVD disc automatically starts playing whenever the DVD is inserted. If Auto Play mode is set to On, this DVD player will search a title that playback time is long most and then play back the title automatically.

On: Auto Play function is activated. Off: Auto Play function is not activated.

ote

The Auto Play function may not work for some DVDs.

DVD

DOLBY

/PCM

Disc Audio

Disc Subtitle

Disc Menu

Rating

Country Code

TV Aspect

Menu Language

Digital Audio Output

5.1 Speaker Setup

Others

DIGITAL

Stream/PCM

PCM

Sample Freq.

48 KHz

96KHz

Disc Audio

Disc Subtitle

Disc Menu

Rating

Country Code

TV Aspect

Menu Language

Digital Audio Output

5.1 Speaker Setup

Others

DRC On

Vocal

Auto Play

Off

Before DVD Operation (Continued)

Parental Control

Rating

Movies on DVDs may contain scenes not suitable for children. Therefore, discs may contain Parental Control information that applies to the complete disc or to certain scenes on the disc. These scenes are rated from 1 to 8, and alternatively, more suitable scenes are available for selection on some discs. Ratings are country dependent. The Parental Control feature allows you to prevent discs from being played by your children or to have certain discs played with alternative scenes.

Select Rating on the Setup menu using vv/

buttons.

While Rating is selected, press BB.

When you have not entered a password yet.

Enter a 4-digit password using the numbered buttons to create a personal 4-digit security password, then press SELECT/ENTER. Enter the 4-digit password again and press SELECT/ENTER to verify.

When you have already entered a password;

Enter a 4-digit password using the numerical buttons to confirm the personal 4-digit security password, then press SELECT/ENTER.

If you make a mistake before pressing SELECT/ENTER, press CLEAR and enter 4-digit security password again.

Select a rating from 1 to 8 using vv/VVbuttons. One (1) has the least playback restrictions. Eight (8) has the most playback restrictions.

Unlock: If you select Unlock, Parental Control is not active. The disc will play in full. Ratings 1 to 8: Some discs contain scenes not suitable for children. If you set a rating for the DVD+VCR, all disc scenes with the same rating or lower will be played. Higher rated scenes will not be played unless an alternative scene is available on the disc. The alternative must have the same rating or a lower one. If no suitable alternative is found, playback will stop. You must enter the 4-digit password or change the rating level in order to play the disc.

Press SELECT/ENTER to confirm your rating selection, then press SETUP to exit the menu.

Country Code

Enter the code of a country whose standards were used to rate the DVD video disc, referring to the list (See “Country Code List”, page 37.).

Select the Country Code option using the v/V buttons on the setup menu.

While Country Code is selected, press B.

Follow step 3 of “Rating” on left.

Select the first character using the v/V buttons.

Press 2 to shift to second character and select the second character using v/V buttons.

Press SELECT/ENTER to confirm your Country Code selection, then press SETUP to exit the menu.

ote

Confirmation of the 4-digit password is necessary when the password is changed (see Changing the 4-digit password below ).

Changing the 4-digit password

1 Follow Steps 1-2 as shown above to the left (Rating). 2 Enter the old password, then press SELECT/ENTER. 3 Select Change using v/V buttons then press

SELECT/ENTER.

4 Enter the new 4-digit password, then press

SELECT/ENTER.

5 Enter exactly the same password a second time and

verify by pressing SELECT/ENTER.

6 Press SETUP to exit the menu.

If you forget your 4-digit password

If you forget your password, to clear the current password follow the procedure below.

1 Press SETUP to display the setup menu. 2 Enter the 6-digit number 210499.

The 4-digit password is cleared.

3 Enter a new password as shown

above to the left

(Rating).

DVD

Disc Audio

Disc Subtitle

Disc Menu

Rating

Country Code

TV Aspect

Menu Language

Digital Audio Output

5.1 Speaker Setup

Others

Unlock

Change

Disc Audio

Disc Subtitle

Disc Menu

Rating

Country Code

TV Aspect

Menu Language

Digital Audio Output

5.1 Speaker Setup

Others

Code Set

U S

OPERATION

Tape Operation

Normal Playback

Preparation:



Turn on the TV.



Tune the TV to the DVD+VCR output channel (CH 3 or 4) or set the TV’s source selector to VIDEO.



If a direct VIDEO/AUDIO connection is made between the DVD+VCR and the TV, set the TV’s source selector to VIDEO.



Set the Output Source to VCR as shown in “Selecting the Output Source” on page 6.

Insert a prerecorded video cassette.

The indicator will light and the DVD+VCR will power-up automatically.

 Make sure that the indicator in the display

window is not lighted. If it is, press POWER once.

 If a tape without a safety tab is inserted, the unit will

start playback automatically.

Press PLAY (HH) once.

PLAY appears on the TV screen .

 It is not necessary to select the tape speed for

playback. It will be automatically selected by the DVD+VCR.

 In playback, the TV/VCR selector switches to VCR

mode automatically.

Press STOP (xx) to stop playback.

STOP appears on the TV screen.

 If the tape reaches the end before STOP (x) is

pressed, the DVD+VCR will automatically stop, rewind and eject the tape, and it will turn itself off.

Tracking Control

Auto Tracking

The automatic tracking function adjusts the picture to remove snow or streaks. The AUTO TRACKING function works in the following cases:

 A tape is played back for the first time.  Tape speed (SP, LP, SLP) changes.  Streaks or snow appear because of scratches on the tape.

Manual Tracking

If noise appears on the screen during playback, press either

vv/VV

on the remote control or CH (vv/VV) on the

front panel until the noise on the screen is reduced.

 In case of vertical jitter, adjust these controls very carefully.  Tracking is automatically reset to normal when the tape is

ejected or the power cord is unplugged for more than 3 seconds.

Special Effect Playbacks

Special effects playback notes

 Horizontal lines (noise bars) will appear on the TV screen.

This is normal.

 The audio is automatically muted during special effect modes,

so there is no sound during search.

 During high-speed picture search mode, a short period is

needed to stabilize tape speed when re-entering the PLAY mode. Slight interference may be observed during this period.

This function lets you quickly and visually search for a desired tape section in either direction: forward or reverse.

1 Press BACKWARD (.) or FORWARD (>)

during playback. The DVD+VCR will be activated in the SEARCH mode.

 If the DVD+VCR is left in the SEARCH mode for more

than 3 minutes, the DVD+VCR will automatically enter the PLAY mode, to protect the tape and video heads.

2 To return to playback, press PLAY (H).

Still Picture and Frame-by-Frame Playback

1 Press PAUSE/STEP (X) during playback.

Still picture will appear on the TV screen.

 If a still picture vibrates vertically, stabilize it using

v/V

on the remote control.

 If the DVD+VCR is left in the STILL mode for more than 5

minutes, the DVD+VCR will automatically enter the STOP mode to protect the tape and video heads.

Press PAUSE/STEP (X) repeatedly to advance the video picture one frame at a time while viewing a still picture.

3 To return to playback, press PLAY (H).

Slow Motion

1 While in still mode, press FORWARD (>).

The tape will be played back at a speed 1/19 times slower than the normal speed.

 During slow playback, use v/V on the Remote Control to

minimize noise bands.

 If slow motion mode continues for more than 3 minutes,

the DVD+VCR will automatically change to playback mode.

2 To return to playback, press PLAY (H).

CM Skip (Commercial Skip)

This is useful for skipping commercials or short program segments. 1 Press CM Skip during playback.

The tape will fast forward picture search through 30 seconds of recording.

 Skipping time can be extended by pressing CM Skip

repeatedly.

 Subsequent presses result in advancing the fast forward

picture search time by 30-second increments (maximum 3 minutes).

2 When the search is complete, the DVD+VCR will go

into playback mode automatically.

EZ (EASY) Review

You can replay a specified segment twice.

During playback, press and hold EZ review for more than 3 seconds at the end of the segment and your DVD+VCR will start reverse search.

Release EZ review at the beginning of the segment. The segment is replayed twice automatically.

To return to normal play, press PLAY (HH) during easy review playback.

Tape Operation (Continued)

Normal Recording

Preparation:



Turn on the power of both the DVD+VCR and TV.



Tune the TV to the DVD+VCR output channel (CH 3 or 4) or set the TV’s source selector to VIDEO.



If a direct VIDEO/AUDIO connection is made between the DVD+VCR and the TV, set the TV’s source selector to VIDEO.

Insert a video cassette with the safety tab intact.

Select the desired channel by using vv/VV.



If you are recording from another source via audio/video input jacks (at the Rear or Front panel), select the LINE1 or LINE2 by pressing INPUT.

Set the desired recording speed (SP or SLP) with the SP/SLP button.



This DVD+VCR is not designed to record in LP mode.

Set the MTS mode as desired (See page 15, 25).

Press REC/ITR (zz) once.

Recording will start. (The REC indicator will light in the display window.)



REC indicator appears only when the Output Source is set to VCR.



If a cassette with no safety tab is loaded, the cassette will be ejected automatically.

Press STOP (xx) to stop recording.

If the tape reaches the end before STOP (x) is pressed, the DVD+VCR will automatically stop, rewind, eject the tape and turn itself off.

To pause recording

1 Press PAUSE/STEP (X) to pause the tape during

recording.

The REC indicator will flash in the display window.

2 When you want to continue recording, press

PAUSE/STEP (X) or press REC/ITR (zz).



After 5 minutes in pause mode, the tape will be stopped automatically to protect the tape and the video heads.

To record one TV program while watching another

1 Use TV/VCR to select the TV mode during recording.

The TV indicator appears.

2 Using the TV, select the channel to be viewed.

ips

Always use PAUSE/STEP (X) for best results when making changes during recording. For example: To change channels during recording, first press

PAUSE/STEP (

X) to put the unit in pause mode. Then select

the desired channel on the DVD+VCR, and press PAUSE/STEP (X) again to resume recording.

Timer Recording

This DVD+VCR can be programmed to record up to 8 programs within a period of 1 year. For unattended recording, the timer needs to know the channels to be recorded and the starting and ending times.

Preparation:



Turn on the power of both the DVD+VCR and the TV.



Be sure the TV is set to the DVD+VCR output channel (3 or 4).



Make sure the TUNING BAND in the TUNING menu is set appropriately (TV or CATV).

Press MENU and the MAIN menu will appear.

Use vv/VVto choose the PROGRAM menu.

Press SELECT/ENTER to go to the PROGRAM menu.

The PROGRAM menu will appear.



If all 8 programs have been entered, FULLY PROGRAMMED message will appear for a moment and then PROGRAM 1 will appear on the TV screen.

Use bb/BBto choose the PROGRAM No. (1-8).

Use VVto choose the MONTH option. Use bb/BBto choose the desired month.

Use VVto choose the DAY option. Use bb/BBto choose the desired day.

Use VVto choose the START option. Use bb/BBto choose the desired start time.

Use VVto choose the STOP option. Use bb/BBto choose the desired stop time.

Use VVto choose the CHANNEL option. Use bb/BBto choose the desired channel

(Channel, LINE1 or LINE2).

Cable Users: If you have CABLE TV and used Cable Box

in Connecting Antenna/Cable TV to DVD+VCR (page 11), using a cable box converter, you must set the channel in this step to match the cable box output channel (usually CH 3 or 4). Change channels on the cable box instead of with the DVD+VCR.



If you try to set the program timer before setting the clock, PLEASE SET THE CLOCK appears for a moment and then CLOCK menu appears on the TV screen. Set the time and date before proceeding.



Make sure a tape is in the DVD+VCR and the safety tab is in place or the tape will be automatically ejected.

Things to know before starting

1100

Use VVto choose the SPEED option. Use bb/BBto choose the desired recording

speed (AUTO, SP or SLP).



AUTO mode determines how much tape is left and switches speed from SP to SLP, if necessary, to complete recording the program. There will be some picture and sound distortion at the point of the speed change.

1111

Use VVto choose the REPEAT option. Use bb/BBto choose the desired repeat (ONCE,

WEEKLY or DAILY).

ONCE event....for recording up to 8 programs on a

single day or over the days within a period of 1 year.

WEEKLY event....for recording up to 8 programs on a

certain day of every week.

DAILY event....for recording up to 8 programs at the

same time(s) Monday through Friday.

If the input data is wrong, use vvto select the data and correct it using bb/BB.

1122

Press MENU, the program will be memorized by the DVD+VCR.



indicator lights in the display window.



If the program preset time has past, the PAST TIME PROGRAMMED message will appear on the TV screen. Return to the incorrect program and program it with the correct time.



If you had entered a past date, timer recording will be performed on that date of the next year.



Additional programs may be entered by repeating steps 1-12.

Cable Users: If your cable hookup is via a TV converter box, you can program multiple recordings only on the converter box output channel. This is because the converter determines what channel you view through your DVD+VCR.

If you are finished programming and you want to set the DVD+VCR to record the programs you have entered,

MAKE SURE YOU HAVE INSERTED A TAPE INTO THE DVD+VCR. The DVD+VCR is now set to record the preset

programs.

otes

If the power fails or the DVD+VCR is unplugged from the AC outlet, the correct clock time and timer settings are kept in memory for approximately 3 seconds. After 3 seconds, the clock and program timer must be reset when power is restored. Reset the clock according to instructions.

After setting up a timer recording, recording will start if no other timer recordings are scheduled to occur at the same time (see “Program Priority” at right).

Checking (Erasing) Timer Record Programming

Programming can be checked whenever the DVD+VCR is turned on.

1 Press MENU and the MAIN menu will appear. 2 Use v/V to choose the PROGRAM menu.

Press SELECT/ENTER and the PROGRAM menu will appear.

3 Use b/B to select a program you want to check or

erase. If you want to erase the program, press CLEAR.

4 Press MENU to return to the TV screen.

Program Priority

If the starting and ending times of two or more timer recordings overlap on the same day, priority is given to the earliest recording. For example, in the diagram at left Program number 2 will

not be recorded until Program number 1 is finished. The first part of Program number 2 will not be recorded. Likewise, Program number 3 will not be recorded until Program number 2 is finished, and so on.

OPERATION

Tape Operation (Continued)

Instant Timer Recording

Instant Timer Recording allows you to make a recording easily of a preset length without using the program timer.

Preparation:

 Turn on the power of both the DVD+VCR and the TV.  Be sure the TV is tuned to the DVD+VCR output channel (3 or 4).  If a direct VIDEO/AUDIO connection is made between the

DVD+VCR and the TV, set the TV’s source selector to VIDEO.

Insert a video cassette with the safety tab intact.

Select the desired channel with vv/VVor number (0-9).

The channel number appears on the TV screen.

 If you are recording from another source via audio/video

input jacks (at the Rear or Front panel), select LINE1 or LINE2.

Select the desired recording speed (SP or SLP) with the SP/SLP button.

The tape speed will appear on the TV screen.

Press REC/ITR (zz) twice.

The menu as illustrated, will appear on the TV screen.

 Recording will start. (The indicator will light)

Press REC/ITR (zz) repeatedly to select the recording time length.

At the end of the recording, the DVD+VCR will stop recording and shut off.

 During Instant Timer Recording, changing the channel

on the DVD+VCR will not be possible.

 You can stop the recording by pressing STOP (x).

INSTANT TIMER RECORD MENU

Checking the Recording Time

Press REC/ITR (z) once to check the recording time. The recalled setting will automatically return to the TV screen after 6 seconds.

To extend the Recording Time

The recording time can be extended anytime by pressing REC/ITR (z).

Subsequent presses result in advancing the recording time by 30-minute increments.

otes

 If you press PAUSE/STEP (X) during instant timer record-

ing, the DVD+VCR will enter the recording pause mode. Instant timer recording is cancelled.

 If the DVD+VCR is set to “0H00M”, the DVD+VCR goes to

normal recording mode.

Dubbing and Editing

If you wish to edit or dub your camcorder (or another VCR) recordings to this DVD+VCR, the rear (or Front) panel mounted Audio and Video (A/V) input jacks make the connections quick and easy. These direct A/V jacks will also provide better picture results than using the RF jack on the rear panel.

Connect the camcorder’s (or another VCR’s) A/V outputs to your DVD+VCR as illustrated on page 13.

Set the input channel “LINE2”. (use INPUT to select LINE2.)



If you have connected your DVD+VCR to the A/V input jacks on the rear of DVD+VCR, you should select the input channel LINE1 by pressing INPUT twice.

Play the tape in the camcorder (or another VCR). If you have a TV attached to your DVD+VCR, you can see the video playing.

When you desire the recording to begin, press DVD+VCR’s REC/ITR (zz) once to start.

ote

Before recording, please confirm the recording start position.

Copying from DVD to VCR

This unit allows you to copy the contents of a DVD to a VHS tape.

ote

If the DVD you are attempting to copy is copy protected, you will not be able to copy the disc. It is not permitted to copy Macrovision encoded DVDs. “Lock” is displayed in the display window.

Insert Disc

Insert the disc you wish to copy in the DVD deck and close the disc tray.

Insert VHS Tape

Insert a blank VHS video tape into the VCR deck.

Press the COPY button on the unit front panel.

The DVD will go into Play mode and the VCR will go into Record mode.

 If the DVD disc menu appears, you may need to press

PLAY PLAY (

) manually to begin copying.

 “COPY” indicator will light.

Stop the Copy Process

When the DVD is finished playing, press the VCR button on the remote control and then press STOP (x) to end copying. You must stop the Copy process manually when the DVD movie ends, or the unit may replay and record over and over again.

ote

When you stop the DVD playback during copying, the VCR recording mode stops automatically.

INSTANT TIMER RECORD

CHANNEL 2 SPEED SP

START NOW LENGTH 0H30M

0H30M ..... 9H00M ➝ 0H00M

Length Display

(each additional press of

REC/ITR (zz) increases recording

time 30 minutes)

OPERATION

Tape Operation (Continued)

VHS Hi-Fi Stereo System/ MTS Broadcast

This DVD+VCR is equipped with the VHS Hi-Fi audio sound system for recording and playback. The information below gives a brief description of Hi-Fi audio and how to record and play a tape in the Hi-Fi audio mode.

Playback with Hi-Fi Stereo Audio Sound

A stereo TV with AUDIO/VIDEO input jacks or a stereo audio system is required for true stereo playback. To experience the full and rich stereo sound available with Hi-Fi recorded tapes, we recommend the connection of this unit to a home stereo audio system.

Set the AUDIO MODE option to HI-FI on the SETUP menu .

Set the AUDIO OUTPUT option to STEREO position.

(STEREO) POSITION: The left channel sound (L) is

heard from the left speaker and the right channel sound (R) is heard from the right speaker. (LEFT) POSITION: The left channel sound (L) is heard from both speakers. (RIGHT) POSITION: The right channel sound (R) is heard from both speakers.

Press MENU.

Insert a cassette and press PLAY (HH).

Adjust volume at your stereo system.

MTS (Multi-Channel TV Sound)

This DVD+VCR will decode MTS stereo and bilingual (SAP) off-the-air broadcast sound signals. It also decodes stereo TV sound from local cable companies, as long as they operate on assigned cable frequencies and use the EIA-recommended MTS stereo/bilingual TV

sound system.

Multichannel TV Sound Indicator (MTS)

Shows onscreen as illustrated below when SELECT/ENTER is pressed.



One or both of the indicators will light, depending on the MTS broadcast.

If only STEREO appears on the TV screen.

The DVD+VCR can record in stereo onto the VHS Hi-Fi audio tracks when the BROADCAST TYPE option is in the STEREO position. The DVD+VCR will also record mono audio onto the mono audio track.

If only SAP appears on the TV screen.

Set the BROADCAST TYPE option to SAP.

If STEREO/SAP appears on the TV screen

Use the BROADCAST TYPE option to select the desired recording mode (STEREO or SAP).

SAP (Second Audio Program) Recording

Some stations transmit a Second Audio Program, which is used for a second language or additional information. When the station broadcasts a Second Audio Program, follow the procedure below to record the SAP.

Insert a video cassette with the safety tab intact.

Set the BROADCAST TYPE option to SAP (SETUP menu).

Do this if only the SAP appears on the TV screen or you know the program will use the SAP.

Press MENU.

Select the desired recording speed (SP or SLP) with the SP/SLP button.

Select the desired channel. SAP should appear on the TV screen.

Press REC/ITR (zz) once

You are now recording the program you see and hear on the TV.

Press STOP (xx) to stop recording.

STEREO

Lights up when a stereo broadcast

is being received.

SAP

Lights up when a SAP BILINGUAL

broadcast is being received.

TV screen

CH 4

STEREO/SAP

Tape Operation (Continued)

Tape Counter Memory Feature

Real-Time Counter

Shows length of tape run in hours, minutes, and seconds. Press CLK/CNT to select the real-time counter display. Every press of CLK/CNT changes the TV screen as illustrated below.



Counter changes to “0:00:00” when the cassette is ejected.



The real-time counter does not operate if nothing is recorded on the tape.



The real-time counter will not work unless a tape is inserted.

Counter Memory Function

This is useful if there is a section of tape you want to view immediately after recording or if you want to return to the same point several times.

Begin recording or playing a tape.

Press CLK/CNT repeatedly to display the real-time counter on the TV screen.

At the point that you want locate later, reset the real-time counter to “0:00:00” by pressing CLEAR.

Continue to play or record.

Press STOP (xx) when recording or playback finishes.

Press BACKWARD (..).

The tape automatically stops when the tape counter returns to about “0:00:00”.

Tape Remaining

This function allows the time of the remaining tape to be displayed during recording or playback. Press CLK/CNT until the REM indicator displays on the TV screen during recording or playback.

ote

The remaining tape length indicator may not be displayed correctly depending on the condition of the tape and the kind of the tape (T-140, T-160, or T-210 etc)

Additional Information



In manual recording, Timer recording, Instant Timer Recording, playback, or fast forward modes, the DVD+VCR automatically starts rewinding the tape at the end of the tape. The cassette will stop at the beginning of the tape and be ejected, and the DVD+VCR will turn itself off.



After you have finished using the DVD+VCR, rewind, eject, and remove the cassette. Place the cassette in its protective sleeve to protect it from dust. It is not necessary to rewind the cassette before removing it, but if you do, it will be ready to play or record the next time you use it.



Be sure the DVD+VCR Channel Selector is on the correct channel you wish to record. The channel that is being recorded can always be checked by tuning the television to the DVD+VCR channel (3 or 4) and pressing the TV/VCR selector to turn the DVD+VCR’s TV indicator off.



Do not attempt to hook up more than one television set to the DVD+VCR for either recording or playback.

Auto Play System

This DVD+VCR features automatic playback. Load a cassette (with the safety tab removed).

 The Output Source is changed to VCR mode automatically.  The power turns on automatically and playback begins.  At the end of the tape, the DVD+VCR stops, then rewinds.  The cassette is ejected after rewinding and the VCR turns

itself off automatically.

ote

Auto power off does not function during regular DVD play mode. (DVD+VCR power stays on.)

S-VHS Quasi Playback (SQPB)

 This DVD+VCR can play back S-VHS recorded tapes,

however, it cannot make recordings using S-VHS format tapes.

 SQPB is an abbreviation for S-VHS Quasi Playback.

2:15 AM 0:05:25 REM 1:07

CLOCK COUNTER REMAINING TIME

LOAD

TAPE

AUTO

PLAY

AUTO

REWIND

AUTO

EJECT

AUTO

POWER

OFF

OPERATION

DVD Operation

Playing DVDs

Playback Setup

 Turn on the TV and select the video input source con-

nected to the DVD+VCR.

 Audio system: Turn on the audio system and select

the input source connected to the DVD+VCR.



Set the Output Source to DVD as shown in “Selecting the Output Source” on page 6.

Press OPEN/CLOSE (ZZ) to open the disc tray.

Load your chosen disc in the tray, with the label facing up.

When a double-sided DVD is inserted, make sure the side you want to play is facing down.

Press OPEN/CLOSE (ZZ) to close the tray.

“LOAd” appears in the display window, and playback starts automatically. If playback does not start, press PLAY (H). In some cases, the disc menu might appear instead.

If a menu screen is displayed

A menu screen may appear automatically after loading a DVD.

Use b/B/v/V buttons to select the title/chapter you want to view, then press SELECT/ENTER to start playback. Press TITLE or DISC MENU to return to the menu screen.

otes

 If Parental Control is set and the disc is not within the

Rating settings (not authorized), the 4-digit password must be entered and/or the disc must be authorized (see Parental Control, on page 20).

 DVDs may have a Region Code.  Your DVD+VCR will not play discs that have a Region

Code different from your DVD+VCR. The Region Code for this DVD+VCR is 1 (one).

 Do not keep a fixed image displayed on the screen

for a long time.

Screen Saver

The screen saver picture appears when you leave the DVD+VCR in stop mode for about five minutes.

General Features

ote

Unless stated otherwise, all operations described use the remote control. Some features may also be available on the Setup menu.

Selecting Other TITLEs

If a disc has more than one title, you can select another title as follows:



Press DISPLAY in Stop mode, then press the appropriate number buttons (0-9) then use SELECT/ENTER to select a title number.

Selecting Other CHAPTERs

If a title on a disc has more than one chapter or a disc has more than one track, you can move to another chapter as follows:

 Press BACKWARD (.) or FORWARD (>) briefly

during playback to return to the beginning of the current chapter or to select the next chapter.



Press BACKWARD (.) twice briefly to step back to the previous chapter.



To go directly to any chapter during playback, press DISPLAY. Use vv/VVto select Chapter icon.

Then, enter the chapter number with the number buttons (0-9). Then, press SELECT/ENTER.

Slow Motion

1 Press PAUSE/STEP (X) during playback.

The DVD+VCR will now go into PAUSE mode.

2 Press BACKWARD (.) or FORWARD (>)

during pause mode.

The DVD+VCR will enter SLOW mode.

3 Use BACKWARD (.) or FORWARD (>) to

select the required speed: t 1/16, t 1/8, t 1/4, t 1/2 (backward), or T 1/16, T 1/8, T 1/4, T 1/2 (forward).

4 To return to playback, press PLAY (H).

DVD

1 /12

1 /3

DVD Operation (Continued)

General Features (continued)

Still Picture and Frame-by-frame playback

1 Press PAUSE/STEP (X) during playback.

The DVD+VCR will now go into PAUSE mode.

2 With a DVD, you can advance the picture frame by

frame by pressing PAUSE/STEP (X) repeatedly on the remote control.

3 To return to playback, press PLAY (H).

Press and hold BACKWARD (.) or FORWARD (>) for about two seconds during playback.

The DVD+VCR will now go into SEARCH mode.

Press and hold BACKWARD (.) or FORWARD (>) repeatedly to select the required speed: mX2, mX4,

mX16, mX100 (backward) or MX2, MX4, MX16, MX100 (forward).

3 To return to playback, press PLAY (H).

Random

1 Press RANDOM during playback or in Stop mode.

The unit automatically begins Random Playback and “RANDOM” appears on the TV screen.

2 To return to normal playback, press RANDOM until

“NORMAL” appears on the TV screen.

ips

By pressing BACKWARD (.) or FORWARD (>) during Random playback, the unit selects another title (track) and resumes Random playback.

ote

This function only works with DVD Karaoke discs.

Repeat

DVD Video Discs - Repeat Chapter/Title/Off 1 To repeat the currently playing chapter, press

REPEAT.

The Repeat Chapter icon appears on the TV screen.

2 To repeat the title currently playing, press REPEAT a

second time.

The Repeat Title icon appears on the TV screen.

3 To exit Repeat mode, press REPEAT a third time.

The Repeat Off icon appears on the TV screen.

Repeat A-B

To repeat a sequence in a title: 1 Press A-B at your chosen start point.

“ A * ” appears briefly on the TV screen.

2 Press A-B again at your chosen end point.

“A B” appears briefly on the TV screen, and the repeat sequence begins.

3 To cancel the sequence, press A-B.

Time Search

The Time Search function allows you to start playing at any chosen time on the disc.

1 Press DISPLAY during playback. The on-screen dis-

play appears on the screen.

The Time Search box shows the elapsed playing time of the current disc.

2 Within 10 seconds, use vv/VVto select the Time

Search icon in the on-screen display.

The “-:--:--” appears in the Time Search box.

3 Within 10 seconds, use the numbered buttons to

enter the required start time. Enter hours, minutes and seconds from left to right in the box.

If you enter the wrong numbers, press CLEAR to remove the numbers you entered. Then enter the correct numbers.

4 Within 10 seconds, press SELECT/ENTER.

Playback starts from the selected time on the disc. If you enter an invalid time, playback will continue from the current point.

3D Surround

This unit can produce a 3D Surround effect, which simulates multi-channel audio playback from two conventional stereo speakers, instead of the five or more speakers normally required to listen to multichannel audio from a home theater system.

1 Press DISPLAY during playback. 2 Use v/V to select the sound icon.

The sound option will be highlighted.

3 Use b/B to to select “3D SUR”.

To turn off the 3D Surround effect, select “NORM.”.

Zoom

The Zoom function allows you to enlarge the video image and to move through the enlarged image.

1 Press ZOOM during playback or still playback to acti-

vate the Zoom function.

If you press ZOOM repeatedly, the magnification level increases up to six steps.

2 Use b/B/v/V buttons to move through the zoomed

picture.

3 Press CLEAR to resume normal playback or return to

the paused image.

ote

 The zoom function may not work with some DVDs.  The zoom function may not work with some multi-

angle scenes.

DVD

OFF

A B

A *

DVD

OFF

TITLE

CHAPT

DVD

Karaoke DVD

DVD

0:16:57

-:--:--

NORM.

3D SUR

OPERATION

DVD Operation (Continued)

General Features (Continued)

Marker Search

You can start playback from a memorized point. Up to nine points can be memorized. To enter a mark, follow these steps.

1 During disc playback, press MARKER when playback

reaches the spot that you want to memorize.

The Marker icon will appear on the TV screen briefly.

2 Repeat step 1 to enter up to nine Marker points on a

disc.

To Recall a Marked Scene 1 During disc playback, use SEARCH.

The Marker Search menu will appear on the screen.

2 Within 10 seconds, use 1/2 or number button to

select a Marker number that you want to recall.

3 Press SELECT/ENTER.

Playback will start from the Marked scene.

4 To remove the MARKER SEARCH menu, press

SEARCH.

To Clear a Marked Scene 1 During disc playback, press SEARCH.

The Marker Search menu will appear on the screen.

2 Within 10 seconds, use 1/2 or number button to

select a Marker number that you want to erase.

3 Press CLEAR.

The Marker number will be erased from the list.

4 Repeat steps 2 and 3 to erase additional Marker

numbers.

5 To remove the MARKER SEARCH menu, press

SEARCH.



All marker search menu that you selected is erased

by withdrawing the disc.

Special DVD Features

Checking the contents of DVD Video discs: Menus

DVDs may contain menus that allow you to access special features. To use the disc menu, press DISC MENU. Then, press the appropriate number button to select an option. Or, use b/B/v/V buttons to highlight your selection, then press SELECT/ENTER.

Title Menu

1 Press TITLE.

If the current title has a menu, the menu will appear on the screen. Otherwise, the disc menu may appear.

2 The menu can list camera angles, spoken language

and subtitle options, and chapters for the title.

3 To remove the title menu, press TITLE again.

Disc Menu

1 Press DISC MENU.

The disc menu is displayed.

2 To remove the disc menu, press DISC MENU again.

Camera Angle

If the disc contains sequences recorded from different camera angles, the angle icon blinks on the TV screen. You can then change the camera angle if you wish.



Press ANGLE repeatedly during playback to select a desired angle.

The number of the current angle appears on the display.

Changing the Audio Language

Press AUDIO repeatedly during playback to hear a different audio language or audio track.

Subtitles

Press SUBTITLE repeatedly during playback to see the different subtitle languages.

ote

If appears, the feature at that moment or with that specific DVD.

DVD

1/9

MARKER SEARCH

1 ENG

5.1 CH

1 /1

1 ENG

Audio CD and MP3/WMA Disc Operation

Playing an Audio CD and

MP3/WMA

Disc

The DVD Player can play MP3/WMA formatted recordings on CD-ROM, CD-R or CD-RW discs. Before playing MP3/WMA recordings, read the notes on MP3/WMA Recordings on right.

Insert a disc and close the tray. Audio CD; Audio CD menu appears on the TV

screen go to step 4. MP3/WMA disc; The MP3/WMA-JPEG choice menu appears on the TV screen. Go to step 2

Use 33/44to select the MP3/WMA then press SELECT/ENTER.

The MP3/WMA menu appears on the TV screen. Press RETURN to move to the MP3/WMA-JPEG choice menu.

Use33/

to select a folder, and SELECT/ENTER.

A list of files in the folder appears.

Use 33/44to select a track then press PLAY (H) or SELECT/ENTER.

Playback starts. During playback, the current track’s elapsed playing time will appear on the display window and menu. Playback will stop at the end of the disc.

Press TITLE to move to the next page. Press DISC MENU to move to the previous page.

Audio CD Menu MP3/WMA Menu

If you are in a file list and want to return to the Folder list, use the 33/44to highlight and press

SELECT/ENTER to return to the previous menu screen.

To stop playback at any other time, press STOP (xx).

MP3/WMA Recording Notes

About MP3



An MP3 file is audio data compressed by using the MPEG1 audio layer-3 file-coding scheme. We call files that have the “.mp3” file extension “MP3 files”.



The player can not read an MP3 file that has a file extension other than “.mp3”.

About WMA (Window Media Audio) Files



An WMA file is a Microsoft audio compression technology.



WMA(Windows Media Audio) offers double the audio compression of the MP3 format.

MP3/WMA Disc compatibility with this player is limited as follows:

1. Sampling Frequency / only at 44.1kHz (MP3),

22.05 - 44.1kHz (WMA)

2. Bit rate / within 32 - 320kbps (MP3),

32 - 128kbps (WMA)

3. CD-R physical format should be “ISO 9660”

4. If you record MP3/WMA files using the software

which cannot create a FILE SYSTEM, for example “Direct-CD” etc., it is impossible to playback MP3/WMA files. We recommend that you use “EasyCD Creator”, which creates an ISO9660 file system.

5. A single session disc requires MP3/WMA files in the

first track. If there is no MP3/WMA file in the 1st track, it cannot playback MP3/WMA files. If you wish to playback MP3/WMA files, format all the data in the disc or use a new one.

6. File names should be named using 8 letters or less

and must incorporate “.mp3” or “.wma” extension e.g. “********.MP3” or “********.WMA”.

7. Do not use special letters such as “/ : * ? “ < > ” etc.

8. Total number of files on the disc should be less than

650.

This DVD+VCR requires discs/recordings to meet certain technical standards in order to achieve optimal playback quality. Pre-recorded DVDs are automatically set to these standards. There are many different types of recordable disc formats (including CD-R containing MP3 or WMA files). That require certain pre-existing conditions (see above) to insure compatible playback.

Customers should also note that permission is required in order to download MP3/WMA files and music from the Internet. Our company has no right to grant such permission. Permission should always be sought from the copyright owner.

WMA

MP3CD

Program

STER. NORM.

0: 56: 18

TRACK01

TRACK02

TRACK03

TRACK04

TRACK05

TRACK06

TRACK07

TRACK08

Clear All

FILE 1

FILE 2 FILE 3 FILE 4 FILE 5 FILE 6 FILE 7 FILE 8

Program

MP3 WMA

OFF00:00

Clear All

JPEG

MP3 WMA

Folder1

Folder2

Folder3

Folder4

Folder5

Folder6

Folder7

Folder8

MP3 WMA

OFF00:00

Program

Clear All

OPERATION

Audio CD and MP3/WMA Disc Operation (Continued)

Pause

1 Press PAUSE/STEP (X) during playback. 2 To return to playback, press PLAY (H) or press

PAUSE/STEP (X) again.

Selecting other Tracks



Press BACKWARD . or FORWARD > briefly during playback to go to the next track or to return to the beginning of the current track.



Press BACKWARD . twice briefly to step back to the previous track.



On Audio CDs, to go directly to any track, enter the track number using the numbered buttons (0-9) during playback.

Repeat Track/All/Off

1 To repeat the track currently playing, press REPEAT.

The Repeat icon and “TRACK” appears on the menu screen.

2 To repeat all tracks on a disc, press REPEAT a sec-

ond time.

The Repeat icon and “ALL” appears on the menu screen.

3 To cancel Repeat mode, press REPEAT a third time.

The Repeat icon and “OFF” appears on the menu screen.

1 Press and hold BACKWARD . or FORWARD >

for about two seconds during playback.

The player will now go into SEARCH mode.

2 Press and hold BACKWARD . or FORWARD >

repeatedly to select the required speed: mX2, mX4, mX8 (backward) or MX2, MX4, MX8 (forward).

Search speed and direction are indicated on the menu screen.

3 To exit SEARCH mode, press PLAY (H).

Random

1 Press RANDOM during playback or in Stop mode.

The unit automatically begins Random Playback and RANDOM or “RAND.” appears on the display window and menu screen.

2 To return to normal playback, press RANDOM repeat-

edly until RANDOM or “RAND.” disappears from the display window and menu screen.

Repeat A-B

To repeat a sequence. 1 During disc playback, press A-B at your chosen start-

ing point.

The Repeat icon and “A* ” appears on the menu screen.

2 Press A-B again at your chosen end point.

The Repeat icon and “A B” appears on the menu screen, and the sequence begins to play repeatedly.

3 To exit the sequence and return to normal play, press

A-B again.

The Repeat icon and “OFF” appears on the menu screen.

3D Surround

1 Press DISPLAY or AUDIO during playback. 2 Use b/B to select the sound icon.

The sound option will be highlighted.

3 Use v/V to select “NORM.”, or “3D SUR”.

Changing the Audio Channel

Press AUDIO repeatedly during playback to hear a different audio channel (STER., LEFT, or RIGHT).

WMA

MP3CD

WMA

MP3CD

WMA

MP3CD

WMA

MP3CD

WMA

MP3CD

JPEG Files Operation

Viewing JPEG files

This DVD+VCR can play discs with JPEG files. Before playing JPEG files, read the notes on JPEG Files on right.

Insert a disc and close the tray.

The MP3/WMA-JPEG choice menu appears on the TV screen.

Use 33/44to select the JPEG then press SELECT/ENTER.

The JPEG menu appears on the TV screen.

Use33/

to select a folder, and SELECT/ENTER.

A list of files in the folder appears. Press RETURN to move to the MP3/WMA-JPEG choice menu.

If you are in a file list and want to return to the Folder list, use the 34 buttons on the remote to highlight “

”

and press SELECT/ENTER to return to the

previous menu screen.

If you want to view a particular file, use 33/44to highlight the file and press SELECT/ENTER or PLAY (HH).

Viewing the file function starts. While viewing a file, press RETURN to move to the previous menu (JPEG menu).

Press TITLE to move to the next page. Press DISC MENU to move to the previous page.

There are three viewing Slide Speed options: Fast, Normal, Slow, and Off. Use 1/2 to highlight the Slide Speed then use 3/4 to select the option you want to use, and press SELECT/ENTER.

To stop viewing at any other time, press STOP (xx).

The JPEG menu appears.

Selecting other Files

Press BACKWARD . or FORWARD > once while viewing a picture to advance to the next file or to the previous file.

Still Picture

1 Press PAUSE/STEP (X) during slide show.

The player will now go into PAUSE mode.

2 To return to the slide show, press PLAY (HH) or press

PAUSE/STEP (X) again.

To flip the picture

Press 33/44while showing a picture to flip the picture horizontally or a vertically.

To rotate picture

Press 1/2 while showing a picture to rotate the picture clockwise or counter clockwise.

Notes on JPEG Files



Depending upon the size and number of the JPEG files, it could take a long time for the DVD player to read the disc’s contents. If you don’t see an onscreen display after several minutes, some of the files are too big — reduce the resolution of the JPEG files to less than 2 mega pixels and burn another disc.



Total number of files and folders on the disc should be less than 650.



Some disc may be incompatible due to different recording format or condition of disc.

 When you are using software such as “Easy CD

Creator” to burn the jpeg files into the CD-R, ensure that all the selected files have the “.jpg” extensions when copying into the CD layout.

 If the files have “.jpe” or “.jpeg” extensions, please

rename them as “.jpg” files.

 File names without “.jpg” extension will not be able to

be read by this DVD+VCR, even though the files are shown as JPEG image files in windows explorer.

JPEG

Slide Speed

5/32 1024X768

Picture1

Picture2

Picture3

Picture4

Picture5

Picture6

Picture7

JPEG

Off

Folder1

MP3 WMA

JPEG

5/32 Picture5.jpg1024X768

Slide Speed

Off

Folder1

Folder2

Folder3

Folder4

Folder5

Folder6

Folder7

Folder8

JPEG

OPERATION

Programmed Playback

WMA

MP3CD

Programmed Playback with Audio CDs and MP3/WMA Discs

The Program function enables you to store your favorite tracks from any disc in the player memory.

Program can contain 30 tracks.

Press PROGRAM during playback or in the Stop mode to enter the Program Edit mode.

The mark will appear to the right of the word Program on the right side of the menu screen.

ote

Press PROGRAM to exit the Program Edit mode; the mark will disappear.

Select a track, then press SELECT/ENTER to place the selected track on the Program list.

Repeat step 2 to place additional tracks on the Program list.

Audio CD Menu MP3/WMA Menu

Press 2.

The programmed track you selected last is highlighted on the program list.

Use 33/44to select the track you want to start playing.

Press TITLE to move to the next page. Press DISC MENU to move to the previous page.

Press PLAY (HH) to start.

Playback begins in the order in which you programmed the tracks and “PROG.” appears on the menu screen. Playback stops after all of the tracks on the Program list have played once.

To resume normal playback from programmed playback, press PROGRAM. Select a track on the CD (or MP3/WMA) list and then press SELECT/ENTER.

“PROG.” indicator disappears from the display window.

Repeat Programmed Tracks/All/Off



To repeat the track currently playing, press REPEAT.

The Repeat icon and “TRACK” appear on the menu screen.



To repeat all tracks on the program list, press REPEAT a second time.

The Repeat icon and “ALL” appear on the menu screen.



To cancel Repeat mode, press REPEAT a third time.

The Repeat icon and “OFF” appear on the menu screen.

Erasing a Track from Program List

1 Press PROGRAM during playback or in the Stop

mode to enter the Program Edit mode.

The mark will appear.

2 Press 2 to move to the Program list. 3 Use 33/44to select the track that you wish to erase

from the Program list.

4 Press CLEAR.

The track will be erased from the Program list.

Erasing the Complete Program List

1 Follow steps 1-2 of “Erasing a Track from Program

List” as above.

2 Use 33/44to select “Clear All”, then press

SELECT/ENTER.

The complete Program for the disc will be erased. The programs are also cleared when the disc is removed.

TRACK 1

TRACK 2

TRACK 3

TRACK 4

TRACK 5

TRACK 6

TRACK 7

TRACK 8

0: 56: 18

Program

TRACK 12

TRACK 8

TRACK 10

TRACK 3

Clear All

STER. NORM.

MP3 WMA

FILE 1 FILE 2

FILE 3

FILE 4 FILE 5 FILE 6 FILE 7 FILE 8

Program

FILE 8

FILE 2

FILE 4

FILE 3

Clear All

OFF00:00

Symptom

No power.

The power is on, but the DVD+VCR does not work.

No picture.

No sound.

The playback picture is poor.

The DVD+VCR does not start playback.

The remote control does not work properly.

Cause

 The power cord is disconnected.

 No disc is inserted.  No tape is inserted.

 The TV is not set to receive DVD+VCR

signal output.

 TV/VCR mode for DVD+VCR is set to

TV.

 The video cable is not connected

securely.

 The connected TV power is turned off.  The equipment connected with the

audio cable is not set to receive DVD+VCR signal output.

 The audio cables are not connected

securely.

 The power of the equipment connected

with the audio cable is turned off.

 The Digital Audio Output is set to the

wrong position.

 The disc is dirty.  Tape heads are dirty.  Tape is a rental or was recorded on

another VCR.

 No disc is inserted.  No tape is inserted.

 An unplayable disc is inserted.

 The disc is placed upside down.  The disc is not placed within the guide.

 The disc is dirty.  The Rating level is set.

 The remote control is not pointed at the

remote sensor of the DVD+VCR.

 The remote control is too far from the

DVD+VCR.

 There is an obstacle in the path of the

remote control and the DVD+VCR.

 The batteries in the remote control are

exhausted.

 This remote control use the same

buttons for VCR and DVD functions (ex. PLAY).

Correction

 Plug the power cord into the wall outlet

securely.

 Insert a disc or tape. (Check that the

disc or tape indicator in the display window is lit.)

 Select the appropriate video input mode

on the TV so the picture from the DVD+VCR appears on the TV screen.

 Press the TV/VCR button on the remote

control repeatedly to choose VCR mode. TV indicator disappears from the display window.

 Connect the video cable securely.

 Turn on the TV.  Select the correct input mode on the

audio receiver so you can listen to the sound from the DVD+VCR.

 Connect the audio cable securely.

 Turn on the equipment connected with

the audio cable.

 Set the Digital Audio Output to the

correct position, then turn on the DVD+VCR again by pressing POWER.

 Clean the disc.  Clean video heads.  Use

v/V

for manual tracking adjustment

while tape is playing.

 Insert a disc or tape. (Check that the

disc or tape indicator in the display window is lit.)

 Insert a playable disc. (Check the disc

type, color system, and Regional code.)



Place the disc with the playback side down.

 Place the disc on the disc tray correctly

inside the guide.

 Clean the disc.  Cancel the Rating function or change

the rating level.

 Point the remote control at the remote

sensor of the DVD+VCR.

 Operate the remote control within 23 ft

(7 m).

 Remove the obstacle.

 Replace the batteries with new ones.

 When using a VCR, first press the VCR

button. When using a DVD, first press the DVD button.

Check the following guide for the possible cause of a problem before contacting service.

Troubleshooting

REFERENCE

Troubleshooting (Continued)

Symptom

Some channels are skipped over when using

v/V

Picture and sound of broadcasting channel are weak or missing.

Camcorder image is not shown.

Camcorder image via A/V input to DVD+VCR is not shown on TV screen.

Timer recording is not possible.

indicator

appears after DVD+VCR is turned off.

Stereo Audio Record and/or Playback is not present.

Cause

 Those channels were deleted with the

CH. ADD/DEL option.

 Antenna or cables are loose.

 Wrong TUNING BAND option is being

used.

 Camcorder is off.

 DVD+VCR SOURCE SELECT is not set

to LINE1 or LINE2.

 Clock in DVD+VCR is not set to correct

time.

 Timer has been programmed

incorrectly.

 indicator does not appear after pro-

gramming timer.

 DVD+VCR is in Timer Recording mode.

 TV is not Stereo-compatible.  Broadcast program is not in stereo for-

mat.

 DVD+VCR A/V Out jacks are not con-

nected to TV A/V In jacks.

 DVD+VCR Audio/Video Out is not

selected for viewing at the TV.

 DVD+VCR BROADCAST TYPE mode is

set to SAP or MONO.

Correction

 Use CH. ADD/DEL. to restore channels.

See “Channel Selection” on page 15.

 Tighten connections or replace cable.

 Try all TUNING BAND options. See

“Channel Selection” on page 15 for details.

 Turn camcorder on and operate

properly.

 Press INPUT to select LINE input

channel (LINE1 or LINE2).

 Set clock to correct time. See “Setting

the Clock” on page 16.

 Reprogram Timer. See “Timer

Recording” on pages 22 and 23.

 Reprogram Timer.

 This is the normal indication that the

DVD+VCR is in TIMER mode.

 No action is possible.  No action is possible.

 Make A/V connections. Stereo is

available only via A/V output from DVD+VCR.

 Select AUX or A/V source as TV input.

 Set BROADCAST TYPE mode to

STEREO. See “Setting the VCR Setup Menu Options” on page 15.

Moisture Condensation

Moisture condensation can occur:

• When the DVD+VCR is moved from a cold place to a warm place.

• Under extremely humid conditions.

In locations where moisture condensation may occur:

•

Keep the DVD+VCR plugged into an AC power outlet with POWER On. This will help prevent condensation.

• When condensation has occurred, wait a few hours for the DVD+VCR to dry before using it.

Language Code List

Language Code

Abkhazian 6566

Afar 6565

Afrikaans 6570

Albanian 8381

Amharic 6577

Arabic 6582

Armenian 7289

Assamese 6583

Aymara 6588

Azerbaijani 6590

Bashkir 6665

Basque 6985

Bengali; Bangla 6678

Bhutani 6890

Bihari 6672

Breton 6682

Bulgarian 6671

Burmese 7789

Byelorussian 6669

Cambodian 7577

Catalan 6765

Chinese 9072

Corsican 6779

Croatian 7282

Czech 6783

Danish 6865

Dutch 7876

English 6978

Esperanto 6979

Estonian 6984

Faeroese 7079

Language Code

Fiji 7074

Finnish 7073

French 7082

Frisian 7089

Galician 7176

Georgian 7565

German 6869

Greek 6976

Greenlandic 7576

Guarani 7178

Gujarati 7185

Hausa 7265

Hebrew 7387

Hindi 7273

Hungarian 7285

Icelandic 7383

Indonesian 7378

Interlingua 7365

Irish 7165

Italian 7384

Japanese 7465

Javanese 7487

Kannada 7578

Kashmiri 7583

Kazakh 7575

Kirghiz 7589

Korean 7579

Kurdish 7585

Laothian 7679

Latin 7665

Latvian, Lettish 7686

Language Code

Lingala 7678

Lithuanian 7684

Macedonian 7775

Malagasy 7771

Malay 7783

Malayalam 7776

Maltese 7784

Maori 7773

Marathi 7782

Moldavian 7779

Mongolian 7778

Nauru 7865

Nepali 7869

Norwegian 7879

Oriya 7982

Panjabi 8065

Pashto, Pushto 8083

Persian 7065

Polish 8076

Portuguese 8084

Quechua 8185

Rhaeto-Romance 8277

Romanian 8279

Russian 8285

Samoan 8377

Sanskrit 8365

Scots Gaelic 7168

Serbian 8382

Serbo-Croatian 8372

Shona 8378

Sindhi 8368

Language Code

Singhalese 8373

Slovak 8375

Slovenian 8376

Somali 8379

Spanish 6983

Sudanese 8385

Swahili 8387

Swedish 8386

Tagalog 8476

Tajik 8471

Tamil 8465

Tatar 8484

Telugu 8469

Thai 8472

Tibetan 6679

Tigrinya 8473

Tonga 8479

Turkish 8482

Turkmen 8475

Twi 8487

Ukrainian 8575

Urdu 8582

Uzbek 8590

Vietnamese 8673

Volapük 8679

Welsh 6789

Wolof 8779

Xhosa 8872

Yiddish 7473

Yoruba 8979

Zulu 9085

Enter the appropriate code number for the initial settings “Disc Audio”, “Disc Subtitle” and/or “Disc Menu” (See page 18).

REFERENCE

Country Code List

Code Country

AD Andorra AE United Arab Emirates AF Afghanistan AG Antigua and Barbuda AI Anguilla AL Albania AM Armenia AN Netherlands Antilles AO Angola AQ Antarctica AR Argentina AS American Samoa AT Austria AU Australia AW Aruba AZ Azerbaidjan BA Bosnia-Herzegovina BB Barbados BD Bangladesh BE Belgium BF Burkina Faso BG Bulgaria BH Bahrain BI Burundi BJ Benin BM Bermuda BN Brunei Darussalam BO Bolivia BR Brazil BS Bahamas BT Bhutan BV Bouvet Island BW Botswana BY Belarus BZ Belize CA Canada CC Cocos (Keeling) Islands CF Central African Republic CG Congo CH Switzerland CI Ivory Coast CK Cook Islands CL Chile CM Cameroon CN China CO Colombia CR Costa Rica CS Former Czechoslovakia CU Cuba CV Cape Verde CX Christmas Island CY Cyprus CZ Czech Republic DE Germany DJ Djibouti DK Denmark DM Dominica DO Dominican Republic DZ Algeria EC Ecuador EE Estonia EG Egypt EH Western Sahara

Code Country

ER Eritrea ES Spain ET Ethiopia FI Finland FJ Fiji FK Falkland Islands FM Micronesia FO Faroe Islands FR France FX France (European

Territory) GA Gabon GB Great Britain GD Grenada GE Georgia GF French Guyana GH Ghana GI Gibraltar GL Greenland GM Gambia GN Guinea GP Guadeloupe (French) GQ Equatorial Guinea GR Greece GS S. Georgia & S. Sandwich

Isls. GT Guatemala GU Guam (USA) GW Guinea Bissau GY Guyana HK Hong Kong HM Heard and McDonald

Islands HN Honduras HR Croatia HT Haiti HU Hungary ID Indonesia IE Ireland IL Israel IN India IO British Indian Ocean

Territory IQ Iraq IR Iran IS Iceland IT Italy JM Jamaica JO Jordan JP Japan KE Kenya KG Kyrgyzstan KH Cambodia6 KI Kiribati KM Comoros KN

Saint Kitts & Nevis Anguilla KP North Korea KR South Korea KW Kuwait KY Cayman Islands KZ Kazakhstan LA Laos LB Lebanon

Code Country

LC Saint Lucia LI Liechtenstein LK Sri Lanka LR Liberia LS Lesotho LT Lithuania LU Luxembourg LV Latvia LY Libya MA Morocco MC Monaco MD Moldavia MG Madagascar MH Marshall Islands MK Macedonia ML Mali MM Myanmar MN Mongolia MO Macau MP Northern Mariana Islands MQ Martinique (French) MR Mauritania MS Montserrat MT Malta MU Mauritius MV Maldives MW Malawi MX Mexico MY Malaysia MZ Mozambique NA Namibia NC New Caledonia (French) NE Niger NF Norfolk Island NG Nigeria NI Nicaragua NL Netherlands NO Norway NP Nepal NR Nauru NU Niue NZ New Zealand OM Oman PA Panama PE Peru PF Polynesia (French) PG Papua New Guinea PH Philippines PK Pakistan PL Poland PM Saint Pierre and Miquelon PN Pitcairn Island PR Puerto Rico PT Portugal PW Palau PY Paraguay QA Qatar RE Reunion (French) RO Romania RU Russian Federation RW Rwanda SA Saudi Arabia SB Solomon Islands

Code Country

SC Seychelles SD Sudan SE Sweden SG Singapore SH Saint Helena SI Slovenia SJ Svalbard and Jan Mayen

Islands SK Slovak Republic SL Sierra Leone SM San Marino SN Senegal SO Somalia SR Suriname ST Saint Tome and Principe SU Former USSR SV El Salvador SY Syria SZ Swaziland TC Turks and Caicos Islands TD Chad TF French Southern

Territories TG Togo TH Thailand TJ Tadjikistan TK Tokelau TM Turkmenistan TN Tunisia TO Tonga TP East Timor TR Turkey TT Trinidad and Tobago TV Tuvalu TW Taiwan TZ Tanzania UA Ukraine UG Uganda UK United Kingdom UM USA Minor Outlying

Islands US United States UY Uruguay UZ Uzbekistan VA Vatican City State VC Saint Vincent &

Grenadines VE Venezuela VG Virgin Islands (British) VI Virgin Islands (USA) VN Vietnam VU Vanuatu WF Wallis and Futuna Islands WS Samoa YE Yemen YT Mayotte YU Yugoslavia ZA South Africa ZM Zambia ZR Zaire ZW Zimbabwe

Enter the appropriate code number for the initial setting “Country Code” (See page 20).

General

Power requirements AC 120V , 60 Hz

Power consumption 23W

Dimensions (Approx.) 430 X 97.5 X 293 mm (16.9 x 3.9 x 11.5 inches) (w x h x d)

Weight (Approx.) 4.8 kg (10.58 lbs)

Operating temperature 5˚C to 40˚C (41˚F to 104˚F)

Operating humidity 5 % to 90 %

Signal system NTSC

Inputs

ANTENNA IN Antenna or CATV input, 75 ohms VHS VIDEO IN (LINE1,2) 1 Vp-p 75 ohms, sync negative, RCA jack x 2 VHS AUDIO IN (LINE1,2) -6.0 dBm more than 47 ohms, RCA jack (L, R) x 2

Outputs

VIDEO OUT 1 Vp-p 75 ohms, sync negative

S-VIDEO OUT (Y) 1.0 V (p-p), 75 ohms, negative sync, Mini DIN 4-pin x 1

COMPONENT VIDEO OUT (Y) 1.0 V (p-p), 75 ohms, negative sync, RCA jack x 1

(Pb)/(Pr) 0.7 V (p-p), 75 ohms, RCA jack x 2

Audio output (digital audio) 0.5 V (p-p), 75 ohms, RCA jack x 1

Audio output (analog audio) 2.0 Vrms (1 KHz, 0 dB), 330 ohms, RCA jack (L, R) x 1

RF OUT Channel 3 or 4

VCR Specifications

Head system Four head helical scan azimuth system

Timer 12-hour display type with AM, PM

Tape speed SP: 33.35 mm/sec, LP: 16.67 mm/sec, SLP: 11.12 mm/sec

Tape width 12.7 mm

Maximum recording time SP: 2 HOURS (T-120), SLP: 6 HOURS (T-120)/8 HOURS (T-160)

Rewind time About 3 minutes (T-120)

Antenna 75 ohms (VHF/UHF)

VHF output signal Channel 3 or 4 (Switchable)

Channel coverage VHF: 2-13, UHF: 14-69, CATV: 1-125 (4A, A-W, W+1 - W+84, A-5 - A-1)

Frequency range 20Hz to 20kHz

Signal-to-noise ratio 43dB

Dynamic range 88 dB

Channel separation 60 dB

DVD Specifications

Laser system Semiconductor laser, wavelength 650 nm

Frequency response DVD (PCM 96 kHz): 8 Hz to 44 kHz, DVD (PCM 48 kHz): 8 Hz to 22 kHz

CD: 8 Hz to 20 kHz

Signal-to-noise ratio More than 100dB (ANALOG OUT jacks only)

Harmonic distortion Less than 0.008%

Dynamic range More than 95 dB (DVD/CD)

Accessories:

Video cable x 1, Audio cable x 1, RF 75-ohm Coaxial Cable x 1, Remote control x 1, Batteries (AAA) x 2



Design and specifications are subject to change without prior notice.

Specifications

Notes

Zenith will repair or replace your product, at Zenith’s option, if it proves to be defective in material or workmanship under normal use, during the warranty period (“Warranty Period”) listed below, effective from the date (“Date of Purchase”) of original consumer purchase of the product. This warranty is good only to the original purchaser of the product and effective only when used in the United States, excluding U.S. Territories.

THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE. ZENITH WILL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INDIRECT, OR INCIDENTAL DAMAGES OF ANY KIND, INCLUDING LOST REVENUES OR PROFITS, IN CONNECTION WITH THE PRODUCT. SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY DOES NOT APPLY TO:

• Damages or operating problems that result from shipping, installation, adjustment of user controls, calibration, maintenance or failure to maintain, or separate system components; and

• Damages or operating problems that result from normal wear and tear, misuse, abuse, operation outside environmental specifications or contrary to the requirements or precautions in the Operating Guide, accident, lightning strikes or other natural causes, unauthorized modification or alteration, incorrect electrical current or voltage, software errors that do not disable functionality, operating software protocols adopted after the date of manufacture or for outside the U.S., institutional or commercial use, or other causes not arising out of defect in material or workmanship.

The cost of repair or replacement under these excluded circumstances shall be borne by the consumer.

CUSTOMER INTER-ACTIVE CENTER NUMBERS:

FOR WARRANTY SERVICE:

You must call 1-877-993-6484 (Monday ~ Friday, 7 AM ~ 8 PM CT; and Saturday, 8 AM ~ 5 PM CT) and select appropriate option from the menu to confirm the product is defective and to obtain Return Authorization (RA). If the defect has occurred during the first 90 days of the Warranty Period, Zenith will send you a return-shipping label. After you obtain RA for return, please box your unit with a copy of the sales receipt and enough packing material to ensure undamaged delivery of your product. When you receive the label, place it on the box and call the 800 # in the instruction for pick-up. When your unit is received, Zenith will replace your unit in accordance with this Limited Warranty.

ADVANCE SHIPMENT. If replacement unit is available and you want second day delivery, our service representative will ask for your credit card number. Zenith requires a reserved deposit by credit card as surety for such advance shipment. Your credit card will not be charged if you return the defective unit in 10 business days. For advance shipment, the return label will come with the replacement unit sent to you. Please follow boxing and shipping instructions above.

ZENITH ELECTRONICS CORPORATION Zenith Part No. 206-03919 2000 MILLBROOK DRIVE GS# 3835RM0054F LINCOLNSHIRE, IL 60069 Printed in China

Issue O

WARRANTY PERIOD: LABOR: 90 DAYS from the Date of Purchase. PARTS: ONE YEAR from the Date of Purchase. Repaired or Replacement Unit is warranted for the

remaining period of the original warranty.

HOW SER

VICE IS HANDLED:

This is an Exchange Product. Call 1-877-993-6484

for instructions on getting the defective unit repaired. Please retain dated sales receipt and your box to

return the unit to Zenith for replacement. Shipping charges both ways will be paid by Zenith dur-

ing the first 90 days of the Warranty Period. During the remainder of the Warranty Period (91-365 days), you pay in-bound shipping charges and Zenith pays return shipping charges.

Visit our website at http://www.zenithservice.com

For Warranty Service, Where to buy, Product Assistance, orCustomer Assistance

Call 1-877-9 Zenith (1-877-993-6484) (Monday ~ Friday, 7 AM ~ 8 PM

CT; and Saturday, 8 AM ~ 5 PM CT) and select appropriate options from the menu.

Or visit our website at http://www.zenithservice.com

ZENITH ELECTRONICS CORPORATION

DVD/VCR XBV322 LIMITED WARRANTY-USA

Zenith XBV322 OPERATING GUIDE

Specifications and Main Features

Frequently Asked Questions

User Manual