Zenith LX-230A OPERATING GUIDE

Download

Page 1

CI_LX-230A(ENG)-A075Z

Installation and Operating Guide

Machine Number | LX-230 (Main Unit : LX-230A, Speakers : LXS-230) |

MICRO HI-FI SYSTEM

Page 2

Precautions

Explanation Graphical Symbols:

The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance.

WARNING

TO REDUCE THE RISK OF FIRE OF ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. To avoid electrical shock, do not open the cabinet, Refer servicing to qualified personnel only.

The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

Warning:

Do not install this equipment in a confined space such a book case or similar unit.

Note:

The regulation label is positioned at bottom of this unit.

This label is located on the interior.

This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the exterior.

REGULATORY INFORMATION: FCC Part 15

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the product is operated in a residential installation. This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the product and receiver.

• Connect the product into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Laser component in this product is capable of emitting radiation exceeding the limit for Class 1.

CAUTION:INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.

VARNING:OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD STRÅLEN ÄR FARLIG.

Attention:Quand l'appareil est ouvert, ne pas s'exposer aux radiations invisibles du faisceau laser.

CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1 LASER APPARAT CLASSE 1 PRODUIT LASER

RISK OF ELECTRIC

SHOCK DO NOT OPEN

CAUTION

CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER(OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Page 3

INTRODUCTION

1. Read these instructions. - All these safety and operating instructions should be read before the product is operated.

2. Keep these instructions. - The safety, operating and use instructions should be retained for future reference.

3. Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to.

4. Follow all instructions. - All operating and use instructions should be followed.

5. Do not use this apparatus near water. – For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement; or near a swimming pool; and like.

6. Clean only with dry cloth. – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. -

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over- heating. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding

type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANU-

AL AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this unit will protect you if you observe the following procedures for installation, use, and servicing. This unit does not contain any parts that can be repaired by the user.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

IMPORTANT SAFETY INSTRUCTIONS

Page 4

Table of Contents

INTRODUCTION

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

IMPORTANT SAFETY INSTRUCTIONS . . . . . . 3

Table of Contents . . . . . . . . . . . . . . . . . . . . . . 4

Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Safety Precautions. . . . . . . . . . . . . . . . . . . . 5

Notes on Discs . . . . . . . . . . . . . . . . . . . . . . 5

Notes on Remote Control. . . . . . . . . . . . . . . 5

Notes on Tapes . . . . . . . . . . . . . . . . . . . . . . 5

Front Panel/ Rear Panel . . . . . . . . . . . . . . . . . 6

Remote Control. . . . . . . . . . . . . . . . . . . . . . . . 7

Display Window. . . . . . . . . . . . . . . . . . . . . . . . 7

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Speaker System Connection . . . . . . . . . . . . 8

Antenna (Aerial) Connections. . . . . . . . . . . . 8

BEFORE OPERATION

Audio Adjustment . . . . . . . . . . . . . . . . . . . 9-10

Setting the Voltage (OPTIONAL) . . . . . . . . . 9

Setting the CLOCK . . . . . . . . . . . . . . . . . . . 9

Volume Adjustment . . . . . . . . . . . . . . . . . . . 9

Sound Quality Adjustment . . . . . . . . . . . . . . 9

Sleep Function. . . . . . . . . . . . . . . . . . . . . . . 9

MUTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

SURROUND . . . . . . . . . . . . . . . . . . . . . . . . 9

XDSS (Extreme Dynamic Sound System) . . . . . 9

Timer Function. . . . . . . . . . . . . . . . . . . . . . . . . . 10

Auxiliary Function. . . . . . . . . . . . . . . . . . . . . 10

OPERATION

Presetting the radio stations . . . . . . . . . . . . 11

Listening to the radio . . . . . . . . . . . . . . . . . . 11

Tape Playback . . . . . . . . . . . . . . . . . . . . . . . . 12

Basic Playback. . . . . . . . . . . . . . . . . . . . . . 12

To Stop Play. . . . . . . . . . . . . . . . . . . . . . . . 12

Tape Counter Reset . . . . . . . . . . . . . . . . . . 12

To Play Rewind or Fast Forward. . . . . . . . . 12

Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Basic Setting . . . . . . . . . . . . . . . . . . . . . . . 12

Recording from Radio, CD or Auxiliary

source . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

CD to Tape Synchronized Recording . . . . . 12

CD Playback . . . . . . . . . . . . . . . . . . . . . . . . . 13

Basic Playback. . . . . . . . . . . . . . . . . . . . . . 13

To Pause Play . . . . . . . . . . . . . . . . . . . . . . 13

To Stop Play. . . . . . . . . . . . . . . . . . . . . . . . 13

To Skip the Track . . . . . . . . . . . . . . . . . . . . 13

To Search the Track . . . . . . . . . . . . . . . . . . 13

To Repeat Play. . . . . . . . . . . . . . . . . . . . . . 13

To Program Play . . . . . . . . . . . . . . . . . . . . 13

REFERENCE

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . 14

Specifications . . . . . . . . . . . . . . . . . . . . . . . . 15

About the symbols for instructions

Indicates hazards likely to cause harm to the unit itself or other material damage.

Indicates special operating features of this unit.

Indicates tips and hints for making the task easier.

Page 5

Before Use

INTRODUCTION

Safety Precautions

Handling the unit

When shipping the unit

The original shipping carton and packing materials come in handy. For maximum protection, re-pack the unit as it was originally packed at the factory.

To keep the surface clean

Do not use volatile liquids, such as insecticide spray, near the unit. Do not leave rubber or plastic products in contact with the unit for a long period of time. They will leave marks on the surface.

Cleaning the unit

To clean the cabinet

Use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents, such as alcohol, benzine, or thinner, as these might damage the surface of the unit.

Notes on Discs

Handling discs

Do not touch the playback side of the disc. Hold the disc by the edges so that fingerprints will not get on the surface. Do not stick paper or tape on the disc.

Storing discs

After playing, store the disc in its case. Do not expose the disc to direct sunlight or sources of heat, or leave it in a parked car exposed to direct sunlight, as there may be a considerable temperature increase inside the car.

Cleaning discs

Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the disc from the center out.

Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static spray intended for analog records.

Notes on Remote Control

Remote Control Operation Range

Point the remote control at the remote sensor and press the buttons.



Distance: About 23 ft (7 m) from the front of the

remote sensor.



Angle: About 30° in each direction of the front of the

remote sensor.

Remote control battery installation

Detach the battery cover on the rear of the remote control, and insert two

R03 (size AAA) batteries with and aligned correctly.

Caution

Do not mix old and new batteries. Never mix different types of batteries (standard, alkaline, etc.).

Notes on Tapes

Preventing record

Removing the tab(s) of the cassette (with a small screwdriver) will prevent accidental erasure.

To record again, cover the hole of the tab with adhesive tape.

Side A

Tab for side B

Tab for side A

Adhesive tape.

Page 6

Front Panel/Rear Panel

1. CD DOOR

2. DISPLAY

3. POWER ( STANDBY/ON) button

4. • XDSS button

• SURROUND button

5. • RDS button : OPTIONAL

• SET (CLOCK/ TIMER) button

• CD PAUSE (CD ) button

• COUNTER RESET button (COUNTER) :

OPTIONAL

• CD SYNC. button

• PROG./MEMORY button

• MODE/RIF button

• PLAY MODE button : OPTIONAL

• EQUALIZER (EQ) button

6. HEADPHONE SOCKET ( PHONES): 3.5mm

7. • RECORD/ RECORD PAUSE ( ) button

• TUNING (-/+) button

• CD SKIP/SEARCH ( / ) button

• TAPE REWIND/FAST FORWARD

( / ) button

• PRESET (-/+) button (TUNER)

• BACKWARD PLAY ( ) button (TAPE): OPTIONAL

• PLAY ( ) button (TAPE, CD)

• STOP ( ) button (TAPE, CD)

• CLEAR button

8. PUSH EJECT position -DECK

9. VOLUME CONTROL KNOB

10. FUNCTION SELECT button (TUNER/BAND, CD, TAPE, AUX)

11. • CLOCK button

• TIMER button

12. REMOTE SENSOR

13. CD OPEN/CLOSE

()button

14. ANTENNA TERMINAL

15. AUXILIARY INPUT SOCKET

16. SPEAKER TERMINAL

17. VOLTAGE SELECT SWITCH : OPTIONAL

18. POWER CORD

2 3

12 11 10

1817

ANTENNA

AUX

OPTIONAL

GND

Page 7

INTRODUCTION

Remote Control

1. XDSS button

2. POWER button

3. TUNER/ BAND button

4. AUX button

5. PRESET ( ) button

6. CD FUNCTION buttons

• PLAY/ PAUSE ( ) button

• CD STOP( ) button

• CD SKIP/SEARCH ( / ) button

• REPEAT button

7. TAPE FUNCTION buttons

• RECORD/ RECORD PAUSE button ( )

• BACKWARD PLAY button ( ) : OPTIONAL

• FORWARD PLAY ( ) button

• TAPE STOP button ( )

• FAST FORWARD ( ) button

• REWIND ( ) button

8. SLEEP button

9. PROGRAM button

10. VOLUME CONTROL ( ) button

11. EQUALIZER PATTERN (EQ PATT.) button

12. MUTE button

13. SURROUND (SURR.) button

RECREC

1. MUTE indicator

2. CD PLAY/ PAUSE indicator

3. XDSS (Extreme Dynamic Sound System) indicator

4. TIMER indicator

5. CD SYNCHRO RECORDING indicator

6. SLEEP indicator

7. PROGRAM indicator

8. MEMORY indicator

9. RDS indicator (OPTIONAL)

10. FM STEREO indicator

11. RT, PTY indicator

12. CD REPEAT indicator

13. RECORD/ RECORD PAUSE indicator

14. TAPE PLAY DIRECTION indicator

15. PLAY MODE indicator (OPTIONAL)

16. • VOLUME indicator

• SOUND LEVEL METER

Display Window

2 3

4 5

2 1

12 11 10

34567 91310 12

TIMER

XDSS

REC

MUTE

8 11

SLEEP SYNC

PROG. MEMORY

STEREO ALL1

RDS RT PTY

MHz

kHz

REPEAT

REC

14 15

Page 8

Connections

Speaker System Connection

Connect the speakers using the supplied speaker cords by matching the colors of the terminals and those of the cords. To obtain the best possible surround sound, adjust the speaker parameters (distance, level, etc.).

otes

• Be sure to match the speaker cord to the appropriate terminal on the components: + to + and – to –. If the cords are reversed, the sound will be distorted and will lack base.

• If you use front speakers with low maximum input rating, adjust the volume carefully to avoid excessive output on the speakers.

• Do not disassemble the front cover of supplied speaker.

Antenna (Aerial) Connections

Connect the supplied FM/AM antennas for listening to the radio.

otes

• To prevent noise pickup, keep the AM loop antenna away from the unit and other components.

• Be sure to fully extend the FM wire antenna.

• After connecting the FM wire antenna, keep it as horizontal as possible.

AUX

Right speaker

FM external antenna (aerial) (not supplied)

FM 75

For AM (MW) reception, connect the loop antenna (aerial) to the terminal marked AM

red

AM loop antenna (aerial)

AM (MW) loop antenna (aerial) (Supplied)

(Supplied)

black

FM external antenna (aerial) (not supplied)

Position it for the best reception

75 ohms coaxial cable

Left speaker

FM indoor antenna (aerial)

FM wire antenna (supplied)

Page 9

BEFORE OPERATION

Setting the Voltage (OPTIONAL)

If your set is equipped with a voltage selector at the back side, be sure to set it to your local power supplied before connecting the AC power cord.

Setting the CLOCK

Press CLOCK.

(If the clock requires setting, press and hold CLOCK for more than 2 seconds.)

- The hours begin to flash.

Select a 24 hour cycle or 12 hour cycle by pressing PRESET (-)/(+).

Press SET to confirm the selected hour cycle.

Use PRESET (-)/(+) to set the correct hours.

Press SET.

Use PRESET (-)/(+) to set the correct minutes.

Press SET and the correct time is shown on the display.

Press CLOCK at any time to display the time for about 3 seconds.

Volume Adjustment

• Tu r n VOLUME CONTROL KNOB clockwise to increase the sound level, or counterclockwise to decrease it.

• Press VOLUME CONTROL ( ) to increase the sound level, or press the VOLUME CONTROL ( ) to

decrease it on the remote control.

Sound Quality Adjustment

• To activate stereo sound

You can choose between 4 fixed sound impressions. Select a desired sound mode by using EQ PATT. button on the remote control or EQ button on the front panel. FLAT : linear frequency response ROCK : more bass, more treble POP : less bass, less treble CLASSIC : for orchestral music

• Headphone Socket

Connect a stereo headphone plug ( 3.5mm) into the headphone jack. The speakers are automatically disconnected when you plug in the headphones (not supplied).

Sleep Function

When the sleep timer is used, the power is automatically turned off after the specified time has elapsed.

To specify the time delay before the power is turned off, press SLEEP.

In the display window you can see for about 5 seconds. This means that the system turns off automatically after 90 minutes. Each time the button is pressed the time interval before it turns off is reduced by 10 minutes. i.e.

80...70... etc. Select the desired time to turn off.

To check the remaining time until the power is turned off.

While the sleep function is active press SLEEP briefly.The time remaining until it turns off is displayed for about 5 seconds.

ote

If you press SLEEP while the sleep time is displayed, the SLEEP time is reset.

To cancel the sleep timer mode

If you wish to stop the function, press the SLEEP button repeatedly until SLEEP 10 appears, and then press

SLEEP once again while SLEEP 10 is displayed.

MUTE

Press MUTE to mute your unit. You can mute your unit in order, for example, to answer the telephone, “MUTE” indicator flashes in the display window.

SURROUND

To activate surround mode

Press SURROUND to reinforce surround effect.

SURROUND OFF ↔ SURROUND ON

XDSS (Extreme Dynamic Sound System)

Press XDSS to reinforce treble and bass. The “XDSS ON” or “XDSS OFF” indicator lights up.

To cancel it press XDSS again.

Audio Adjustment

(12HR)

(24HR)

Page 10

Audio Adjustment

Timer Function

The unit can set the clock function in power on/off state. With the TIMER function you can have the radio reception and recording, CD play, tape play or auxiliary source play and recording turned on and off at the time desired.

Press CLOCK to check the current time.

For your reference

If you don’t set clock, timer function doesn’t work.

Press TIMER to enter the timer setting mode.

TUNER-CD-TAPE flashes in the display window in turn.

For your reference

If you want to correct the previous memorized TIMER setting, press and hold the TIMER button more than 2 seconds.

- The previous memorized timer on time and TIMER

indicators appear in the display.

Press SET when the desired function is flashing.

1. a. When you select the TUNER function, ‘PLAY’ and ‘REC’ indicator flash in the display window alternately for about 3 seconds.

‘PLAY’ indicator : TUNER play only ‘REC’ indicator : TUNER play and

recording

b. Select the previous memorized preset

number with PRESET (-)/(+) button and press SET.

- ‘ON TIME’ indicator appears for about 0.5

seconds in the display window and then disappears.

2. When you select the CD or TAPE function,

- ‘ON TIME’ indicator appears for about 0.5

seconds in the display window and then disappears.

Set the hour to switch on by pressing PRESET (-)/(+).

Press SET to confirm the hour to switch on.

Set the minute to switch on by pressing PRESET (-)/(+).

Press SET to confirm the minute to switch on.

‘OFF TIME’ indicator appears for about 0.5

seconds in the display window and then

disappears.

Set the hour to switch off by pressing PRESET (-)/(+).

1100

Press SET to confirm the hour to switch off.

1111

Set the minute to switch off by pressing PRESET (-)/(+).

1122

Press SET.

1133

Adjust the volume level by pressing PRESET (-)/(+).

1144

Press SET.

“

TIMER

” appears in the display window and the

timer setting has been completed.

1155

Switch the system off.

The selected function is automatically switched on and off at the time set.

To cancel or check the timer

Each time the TIMER button is pressed you can select the timer set or cancel. You can also check the timer setting status. To activate or check the timer, press the TIMER button so that “

TIMER

” appears in the display window.

To cancel the TIMER, press the TIMER button so that

“

TIMER

” disappears in the display window.

Auxiliary Function

Connect an auxiliary device i.e. TV or VCR, via the rear mounted AUX phone sockets.

Press AUX .

ote

You can also record from the auxiliary input source, see Recording Section.

Page 11

OPERATION

Presetting the radio stations

You can preset 30 stations for FM and AM. Before tuning, make sure that you have turned down the volume to the minimum.

Press TUNER/BAND to select the frequency (AM or FM) you want.

Every time you press this button, AM and FM changes alternately.

Press TUNING (-)/(+) on the front panel until the frequency indication starts to change.

otes

 Tuning in automatically

Press TUNING(-)/(+) for more than 0.5 seconds.

- Scanning stops when the unit tunes in a station.

 Tuning in manually

Press TUNING(-)/(+) briefly and repeatedly.

Press PROG./MEMORY on the front panel.

A preset number will flash in the display window.

Press PRESET (-)/(+) (or PRESET ( ) on the remote control) to select the preset number you want.

Press PROG./MEMORY again.

- The station is stored.

Repeat steps 2 to 5 to store other stations.

To clear all the memorized stations

Press and hold PROG./MEMORY on the front panel for about two seconds, “CLEAR” appears in the display window and then press CLEAR, the stations are cleared.

For your reference

If all stations have already been entered, FULL message will appear in the display window for a moment and then a preset number will flash. To change the preset number, follow the steps 4-5.

To recall presets

Press and hold PRESET (-)/(+) (or PRESET ( ) on the remote control) until the desired preset number appears or press it repeatedly.

Press TUNER/BAND to select the frequency (AM or FM) you want.

Every time you press this button, AM and FM changes alternately. The last received station is tuned in.

Press PRESET (-)/(+) (or PRESET ( ) on the remote control) repeatedly to select the preset station you want.

- Each time you press the button, the unit tunes in one preset station at a time.

Adjust the volume by rotating VOLUME CONTROL KNOB (or pressing VOLUME

( ) on the remote control) repeatedly.

To listen to non-preset radio stations

• Use manual or automatic tuning in step 2.

• For automatic tuning, press and hold TUNING (-)/(+)

on the front panel.

To turn off the radio

Press POWER to turn the unit off or select another function mode (CD, TAPE or AUX).

For your reference

•

If an FM program is noisy

Press MODE/RIF so that “STEREO” disappears in the display window. There will be no stereo effect, but the reception will improve. Press MODE/RIF again to restore the stereo effect.

•

To improve reception

Reposition the supplied antennas.

otes

 Use MODE/RIF (Radio Interference Filter) function to

switch to mono reception if stereo reception is distorted by noise.

 When recording the MW(AM) or LW broadcast, beat

noises may occur. If it does, press MODE/RIF once.

Listening to the radio

Page 12

Tape Playback

Basic Playback

Press TAPE to select tape function.

(“NO TAPE” appears in the display window.)

Open cassette deck by pushing

PUSH EJECT position.

Insert a cassette with the tape side to the bottom and then close deck.

Press PLAY ( or : OPTIONAL).

To Stop Play

Press STOP( ) during playback.

Tape Counter Reset

Press COUNTER RESET(COUNTER) during playback.

Playing time appears “TP - 0000” in display window.

To Play Rewind or Fast Forward

After pressing / on the front panel or

on the remote control during playback,

or stop, press PLAY( ) at the point you want.

AUTO STOP DECK

After auto stop deck plays only front side, the unit stops automatically.

AUTO REVERSE DECK:OPTIONAL

You can select direction of the cassette you want by pressing PLAY MODE.

Basic Setting

Select the function (CD, TUNER/BAND or AUX) you want to record.

Open the cassette deck and insert a blank cassette into the cassette compartment. To set the recording direction :OPTIONAL

Press PLAY MODE repeatedly to set the recording direction.

Recording from Radio, CD or Auxiliary source

Press on the front panel or the remote control and then select the CD,TUNER or AUX function.

“ REC” flashes and holds the cassette in pause mode.

Press or PLAY( ) on the front panel or the remote control.

The recording begins.

To pause recording

Press during recording.

- “ REC” flashes in display window.

To stop recording

Press TAPE STOP( ).

CD to Tape Synchronized Recording

The CD synchro recording function dubs a complete CD and programmed titles automatically into a cassette.

Press CD SYNC. in stop mode.

“ REC” flashes and “”displays in the display window.

The synchronized recording is started automatically after about 8 seconds.

otes

 If you wish to record from the desired track, select the

desired track with CD SKIP/SEARCH (/

) before commencing CD synchro recording.

 The function change is not possible during recording.

You can use only normal tape.

Wind the tape to the point recording starts. (Use only normal tapes.)

Recording

Pressing

Once

Twice

Three

times

Display Function

After the cassette plays front or reverse (backward play) side, stops automatically.

After the cassette plays front and reverse side, stops automatically.

After the cassette plays six times repeatedly front and reverse side, stops automatically.

Page 13

OPERATION

CD Playback

Basic Playback

Press CD to select CD function.

If no disc is loaded then “NO DISC” is displayed.

Press CD OPEN/CLOSE ( ) and place the disc into the disc tray.

ote

To load an 8cm(3 inch) disc, put it onto the inner circle of the tray.

Press CD OPEN/CLOSE ( ) to close the disc compartment.

Press PLAY ( ) on the front panel or PLAY/ PAUSE ( )

on the remote control

To Pause Play

Press CD PAUSE (CD ) or PLAY/ PAUSE ( ) on the remote control during playback.

Press this button again it to resume play.

To Stop Play

Press STOP( ) on the front panel or CD STOP( ) on the remote control

Press STOP( ) during playback.

To Skip the Track

• Press the CD SKIP/SEARCH (/ )

button to go to the next track.

• When the CD SKIP/SEARCH (/ )

button is pressed once midway through a track, the player returns to the start of that track. When it is pressed again, a track is skipped each time the button is pressed.

To Search the Track

After pressing / on the front panel or the remote control during playback, press PLAY

( ) at the point you want.

To Repeat Play

To play one track repeatedly

Press REPEAT once during playback.

- “REPEAT 1” appears in the display.

To play all tracks repeatedly

Press REPEAT again during playback.

- “REPEAT ALL” appears in the display.

To cancel repeat play

Press REPEAT once more during playback.

- “Repeat indicator” disappears.

To Program Play

You can arrange the order of the tracks on the discs and create your own program.The program can contain up to 20 tracks.

Press PROG./MEMORY (or PROGRAM on the remote control) on the stop mode.

Press / to select the track.

Press PROG./MEMORY (or PROGRAM on the remote control).

Repeat 1~3.

Press PLAY ( ) on the front panel or PLAY/ PAUSE ( )

on the remote control

To check program contents

Press PROG./MEMORY (or PROGRAM on the remote control) on the stop mode.

- A track and program number will be displayed.

To clear program contents

Press PROG./MEMORY (or PROGRAM on the remote control) on the stop mode. And then press CLEAR on

the front panel or STOP( ) on the remote control.

To add program contents

1. Press PROG./MEMORY (or PROGRAM on the

remote control) repeatedly on the program stop mode until “Track Number” blinks.

2. Repeat 2~5.

To modify program contents

1. Press the PROG./MEMORY (or PROGRAM on the

remote control) to display program number you want to modify.

2. Repeat 2~4.

ote

In addition, this unit can play a CD-R or CD-RW that contains audio titles.

Page 14

Troubleshooting

Check the following guide for the possible cause of a problem before contacting service.

Symptom

No power.

No sound.

The unit does not start playback.

The remote control does not work properly.

Cause

• The power cord is disconnected.

• The audio cables are not

connected securely.

• The power of the external source equipment is switched off.

• No disc or tape is inserted.

• An unplayable disc or tape is

inserted.

• The disc is placed upside down.

• The disc is not placed within the

guide.

• The disc is dirty.

• The remote control is not pointed

at the remote sensor of the unit.

• The remote control is too far from the unit.

• There is an obstacle in the path of the remote control and the unit.

• The batteries in the remote control are exhausted.

Correction

• Plug the power cord into the wall outlet securely.

• Connect the audio cable into the jacks securely.

• Switch on the external source equipment.

• Insert a disc or tape.

• Insert a playable disc or tape.

• Place the disc with the playback

side down.

• Place the disc on the disc tray correctly inside the guide.

• Clean the disc.

• Point the remote control at the

remote sensor of the unit.

• Operate the remote control within about 23 ft (7 m).

• Remove the obstacle.

• Replace the batteries with new

ones.

Page 15

REFERENCE

Specifications

[General][CD]

[Tuner]

(MW)

[Amp]

[Speakers]

[

TAPE

]

Power supply AC 120V, 60Hz Power consumption 50W Mass 4.46kg External dimensions (WxHxD) 161 X 255 X 268mm Frequency response 40 - 18000 Hz Signal-to-noise ratio 70 dB Dynamic range 70 dB Tuning Range 87.5 - 108.0 MHz Intermediate Frequency 10.7 MHz Signal to Noise Ratio 60/55 dB Frequency Response 60 - 10000 Hz Tuning Range 530 - 1720 kHz Intermediate Frequency 450 kHz Signal to Noise Ratio 35 dB Frequency Response 100 - 1800 Hz Output Power 20W + 20W T.H.D 0.15% Frequency Response 40 - 25000 Hz Signal-to-noise ratio 80 dB Tape Speed 4.75cm/sec Wow Flutter 0.25% (MTT -111, JIS-WTD) F.F/REW Time 120sec (C-60) Frequency Response 250 - 8000Hz Signal to Noise Ratio 43dB(P/B)/43dB(R/P) Channel Separation 50dB(P/B)/45dB(R/P) Erase Ratio 55dB (MTT-5511)

LXS-230

Type 1 Way 1 Speaker Impedance 6 Ω Frequency Response 85 - 20000 Hz Sound Pressure Level 88 dB/W (1m) Rated Input Power 20 W Max. Input Power 40 W Net Dimensions (WxHxD) 159x248x193mm Net Weight (1EA) 1.87kg

❋ Designs and specifications are subject to change without notice.

LX-230A

MODEL

SECTION

Page 16

P/NO : 3828R-A075Z