Zenith L10V34H, L10V34S Installation And Setup Manual

Download

Page 1

Installation and Setup Guide | Warranty

Model Number | L10V34H | L10V34S | LCD TV/Monitors

table of contents

page

Page 2

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

THIS PRODUCT MUST BE USED WITH UL LISTED MOUNTING BRACKET.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation. Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this product’s compliance is: Zenith Electronics Corporation, 2000 Millbrook Drive, Lincolnshire, IL 60069, USA. Phone: 1-847-941-8000.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

3-WIRE COMM-WARN B-2/02

RECORD THE SERIAL NUMBER

The model and serial number of this LCD TV/Monitor are located on the back of the cabinet. For future reference, we suggest that you record the serial number here:

MODEL NO.____________________________________

SERIAL NO.____________________________________

For Customer Support/Service please call:

1-888-865-3026

www.zenith.com

Page 3

PAGE 3

206-3824

Important safeguards for you and your new product

This product has been manufactured and tested with safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into the new product, please read and observe the following safety points when installing and using the new product, and save them for future reference.

Observing the simple precautions discussed in this installation and operating guide can help get many years of enjoyment and safe operation that are built into the new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.

(Continued on next page)

IMPORTANT SAFETY INSTRUCTIONS

1. Read Instructions

All the safety and operating instructions should be read before the product is operated.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained for future reference.

4. Heed Warnings

All warnings on the product and in the operating instructions should be adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Water and Moisture

Do not use this product near water for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.

7. Accessories, Carts, and Stands

Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

8. Transporting Product

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

9. Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

10. Ventilation

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12. Power Cord Polarization (Some models)

This product is equipped with a three-wire grounding type alternating-current power plug. This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the three-wire ground-type plug.

13. Power Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

PORTABLE CART WARNING

Page 4

PAGE 4

Antenna Lead in Wire

Antenna Discharge Unit (NEC Section 810-20)

Grounding Conductor (NEC Section 810-21)

Ground Clamps Power Service Grounding

Electrode System (NEC Art 250, Part H)

Ground Clamp

Electric Service

Equipment

Example of Grounding According to National Electrical Code Instructions

NEC - National Electrical Code

206-3824

IMPORTANT SAFETY INSTRUCTIONS

(Continued from previous page)

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

15. Lightning

For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

16. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17. Overloading

Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

18. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or

short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

19. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a. If the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the

product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operating instructions as an

improper adjustment of other controls may result in

damage and will often require extensive work by a quali-

fied technician to restore the product to its normal

operation. e. If the product has been dropped or the cabinet has been

damaged. f. If the product exhibits a distinct change in performance.

21. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product.

24. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Page 5

PAGE 5

Table of Contents

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important Safety Instructions . . . . . . . . . . . . . . . 3 - 4

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . 5

Step 1. Hook Up the LCD TV/Monitor

Setup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation/Connections Overview . . . . . . . . . . . . . . 7

VESA Standard TV Mounts . . . . . . . . . . . . . . . . . . . . 8

Install TV on Stand . . . . . . . . . . . . . . . . . . . . . . . . 9

TV and other Equipment Hookup

Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Cable Service . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Antenna with VCR . . . . . . . . . . . . . . . . . . . . . . . . 12

Cable Service with VCR . . . . . . . . . . . . . . . . . . . . . 13

DC Power Hookup/Master Power Switch . . . . . . . . . . . 14

Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . 15

Menus and Displays Overview

On-Screen Menus Overview . . . . . . . . . . . . . . . . . . . 16

Other Menus and On-Screen Displays . . . . . . . . . . . . 17

Optional Installer Remote Control Key Functions . . . . . 18

Step 2. Channel Search and Reception Setup

Auto Program . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

(Select OFF AIR ANTENNA, or CABLE TV and do a channel search)

Step 3. Customize the LCD TV/Monitor Features

Setup Menu (Starts with page 19, Auto Program)

Add/Del/Blank . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Channel Labels . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Clock Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Timer (On/Off Timers) . . . . . . . . . . . . . . . . . . . . . . 23

Captions (Caption/Text) . . . . . . . . . . . . . . . . . . . . . 24

Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Audio Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Bass, Treble, Balance, Audio Mode, Front Surround,

Sound Rite, Speakers

Video Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Contrast, Brightness, Color, Tint, Sharpness, Picture Pref.

Installer Parental Control Menu . . . . . . . . 28 - 29 - 30

Set up Parental Control for the end user.

Managing the Channel Banks . . . . . . . . . . . 31 - 32 - 33

Installer Menus . . . 34 - 35 - 36 - 37 - 38 - 39 - 40 - 41

LT2000 Quickset II Clone Programmer . . . . . 42 - 43 - 44

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . 46

User Operation Section (Copy for User)

Optional L10V34S Remote Control Key Functions . . . . 47

User Parental Control Menu . . . . . . . . . . . . . . . 48 - 49

User Menus and On-Screen Displays . . . . . . . . . . . . . 50

User Front Panel Controls . . . . . . . . . . . . . . . . . . . 51

Warranty for Concierge Series TVs . . . . . . . . . Back Cover

Purchase the Optional Installer’s Remote and Clone Programmer

To perform a normal installation set up, you need an installer’s remote such as the one shown, and the LT2000 Quickset II Clone Programmer—both are shown and described in later sections. The installer remote allows access to the Installer menus, User menus, and Channel Banks in the Manual Channel Set options on the Setup menu. The installer remote has Menu, Select, and Adjust Keys. The LT2000 Quickset II Clone Programmer is used to duplicate a TV’s setup and install it on another identical TV. See your Zenith Dealer.

Note: Design and specifications are subject to change without prior notice.

206-3898

The table of contents lists the pages to go to for setting up the features for the end user

Optional User’s Remote Control for Model No. L10V34S

Shown herein is an optional user’s remote control available for the L10V34S model only. The remote control is NOT included with the LCD TV/Monitor. However, the user’s remote can be purchased separately, see your Zenith dealer. Instructions for operating the remote can be found on page 47. Photocopy Guest operation pages as needed.

Page 6

PAGE 6

206-3824

Setup Checklist

Installation Overview

• Unpack the LCD TV/Monitor and all accessories.

• Determine installation location for the LCD-TV, TV stand, and if used, optional AC to DC Power Converter.

• Determine mounting and installation requirements. If used, AC Power source outlet, Antenna/Cable service connectors, any external equipment required for system or TV operation, all necessary cables, wires, connectors and any other additional required hardware, etc.

Installation Overview & System Setup: Questions to Consider Before Installation

VESA Bracket

Does the VESA Bracket have to be mounted to the TV? Y: Install VESA Bracket on TV following the instructions supplied with the bracket. Yes___ No___

TV Stand

Does the TV have to be mounted on the stand? Y: Mount the TV on the stand following the instructions provided with the TV stand. Yes___ No___

Optional AC to DC Power Converter Installation

Does the optional AC to 12V DC Power Converter need to be mounted on a wall? Y: Install the AC-DC Power Converter on a wall or in an appropriate location. Yes___ No___

Installer’s Remote Control

Does the Installer have an optional Installer’s remote control to use to set up the TV (This is a must for TV setup.)? Yes___ No___

Master TV Setup

Will the Master TV’s features setup be cloned and be copied to other identical LCD TV/Monitors? Yes___ No___

Clone Programmer

To copy the TV’s setup, the installer will need a clone programmer. Is there a Zenith LT2000 Clone Programmer available? Yes___ No___

End-User Remote Control

Will a remote control be provided to the end user to operate the TV? (No remote is included with the TV.) Yes___ No___

End-User Menu Access

Will the end-user have access to all the menus on the TVs from the front panel? Yes___ No___

LCD-TV Setup Checklist

1. Install the LCD TV/Monitor where it will be used.

Prior to Operation

The LCD TV/Monitor must be connected to all external antenna/cable, video, and audio source equipment and a DC power source. See page 5, Table of Contents.

2. Make all external source equipment connections. See pages 10 - 14.

3. Connect DC power or, connect the optional AC to DC power converter to the LCD-TV first, insert the DC power plug into the jack provided on the back of the TV. Then connect the converter to a standard 120V, 60 Hertz, AC power source. See page 14.

Master Power Switch

Once all antenna/cable and external equipment connections have been made, the

master power switch located on the back of the TV must be set to the standby position, ‘I’. To turn the TV’s master power switch off, set the switch to the ‘O’ position. See page 7.

4. Turn on the TV and all source equipment.

Review TV Setup Options in the Installer’s Menu Section

The Installer’s menu includes a number of options for the master TV’s setup that enable the installer or system administrator to devise a unique system using the many different options and variables available. See Installer’s menus section.

Master TV Features Setup for Cloning Overview

• Set up Installer’s remote control, see

page 18.

• Select Tuning Band and do Channel

Search, see page 19.

• Channel Add/Delete/Blank.

• Channel Banks Setup, see Channel Banks

Setup section.

• Video/picture appearance options setup,

see Video menu.

• Audio/sound options setup, see Audio

menu.

• Set up all other features. See page 5,

Table of Contents, for a list of features available on this LCD/Monitor.

Clone Master TV’s Setup

See Clone Programmer section.

Page 7

Installation/Connections Overview

ANTENNA

CABLE

M.P.I.

VIDEO IN

DC IN

L - AUDIO - R

PAGE 7

206-3824

To hook up source equipment, see below and also refer to the Table of Contents on page 5; shows pages to go to for equipment hookup options.

AUDIO/VIDEO IN

Connect Audio/Video equipment to these jacks. See pages 12 - 13.

ANTENNA/CABLE

Connect to an

antenna or cable

system.

See pages 10 - 13.

MASTER POWER SWITCH

‘I’ switches the LCD-TV into standby mode. ‘O’ Turns the power off.

M.P.I. INTERFACE

Use with clone

programmer.

See pages 42 - 44.

DC POWER INPUT (Optional AC - DC converter is available.) See page 14.

Page 8

PAGE 8

206-3824

VESA Standard TV Mounts

VESA Standard 75mm TV Mounts and Stands

Following are shown some examples of VESA standard 75 mm mounts. Since there are numerous types of stands and mounts available, only a few are shown here. Refer to the instructions provided with the TV stand that will be used to mount the TV.

General Guidelines: Choosing a location for installing a VESA Standard Mount

Be sure the style of stand selected is capable of supporting the weight of the TV.

If the mount will be on a wall, a typical wooden stud behind the wall board would be the preferred choice for a location to attach the wall mount. The wall mount location chosen should be appropriate for drilling holes and have available the required power source as well as antenna/cable and other equipment leads.

For pedestal-type mounts, a sturdy surface on a desk or other similar flat table-like surface would be the appropriate location for mounting a pedestal-style TV stand. (Some stands are portable and can be moved from one location to another.) Be sure all safety considerations are followed.

Most stands are designed so that the wiring would be threaded through the stand itself or a loop-through style clamp so that the wiring is neatly bunched and not strung in such a way as to create a potential hazard to the user.

Typical Wall Stud Type Mount with Swivel Bracket

Typical Pedestal Type Mount with Swivel Bracket

75 mm

ANTENNA

CABLE

75 mm

M.P.I.

L - AUDIO - R

DC IN

VIDEO IN

Page 9

PAGE 9

206-3824

Install TV on VESA Standard TV Mount

Installing the TV on VESA Standard 75mm TV Mounts and Stands

Follow the instructions provided with the mounting bracket that will be used for the installation. Since there are numerous types of TV stands and brackets which can be used, these instructions are included and should be thought of only as general guidelines for installing the TV on a mount.

General Guidelines: Preparation for TV installation on a VESA Standard Mount

Remove the two machine screws holding the connection panel cover in place.

Remove the two screws holding the cable clamp in place, remove clamp.

Make all necessary external equipment and other connections to the TV. (See pages 10 - 14.)

Thread all cables into the clamp recess on the TV cabinet.

Replace the cable clamp, reinstall the two screws.

Replace the connection panel cover, reinstall the two screws.

Mount TV to stand as required. See stand installation instructions.

Note: Shown with optional AC to DC Power Converter connected.

M.P.I.

CABLE

ANTENNA

M.P.I.

CABLE

RJ45

RJ11

L - AUDIO - R

VIDEO IN

DC IN

RF IN

ANTENNA

L - AUDIO - R

VIDEO IN

DC IN

M.P.I.

CABLE

L - AUDIO - R

VIDEO IN

DC IN

RJ45

ANTENNA

M.P.I.

CABLE

L - AUDIO - R

VIDEO IN

DC IN

RJ11

RF IN

Page 10

PAGE 10

206-3898

Antenna Hookup

Mini glossary

75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire

sticking through the middle, and it screws onto the threaded jack on the back of the TV.

A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws on one end and a round opening with a wire sticking out on the other end.

Connect an off-air antenna to the LCD TV/Monitor

If the antenna is a 75 ohm RF cable, then no adapters are required.

A 300 to 75 ohm adapter is not included with the Zenith LCD TV/Monitor.

300 TO 75 OHM ADAPTER

Flat Wire

(300 ohm)

Antenna

300/75 ohm

Adapter

Connections Panel

ANTENNA

CABLE

M.P.I.

VIDEO IN

DC IN

L - AUDIO - R

Antenna

Connections Panel

RF Coaxial Wire

(75ohm)

ANTENNA

CABLE

M.P.I.

VIDEO IN

DC IN

L - AUDIO - R

Locate the Antenna/Cable jack on the back of the LCD TV/Monitor.

Connect the antenna wire (Flat or Round) that runs from the wall to this jack, according to one of the diagrams shown to the right.

Plug in the TV. The LCD-TV is designed to operate on DC power.

Once all external connections are complete, go to page 19 to run Auto Program.

Page 11

PAGE 11

206-3898

Cable Service Hookup

Connect cable service to the LCD TV/Monitor

Locate the Antenna/Cable jack on the back of the TV.

Connect the cable wire to the Antenna/Cable jack according to one of the diagrams to the right.

Plug in the TV. The LCD-TV is designed to operate on DC power.

After all external connections are complete, go to page 19 to run Auto Program.

Cable TV Wall Jack

RF Coaxial Wire

(75ohm)

Connections Panel

ANTENNA

CABLE

M.P.I.

VIDEO IN

DC IN

L - AUDIO - R

Cable TV Wall Jack

Cable Box

Out

RF Coaxial Wire

(75ohm)

3 4

output

switch

Connections Panel

ANTENNA

CABLE

M.P.I.

VIDEO IN

DC IN

L - AUDIO - R

For cable box operation, leave the television tuned to channel three or four and use the cable box to change channels.

Page 12

PAGE 12

206-3898

Antenna & VCR Hookup

Connect antenna and a VCR to the LCD-TV

Locate the Antenna/Cable jack on the back of the VCR.

Connect the antenna wire that runs from the wall jack to the VCR. Connect other wires according to the diagram to the right.

Plug in the TV. The LCD-TV is designed to operate on DC power.

After all external connections are complete, go to page 19 to run Auto Program.

Round

Flat wire

(300 ohm)

300/75 ohm

Adapter

Antenna

Out

Video

3 4

VCR Back

VCR Back AV Panel

output

switch

Connections Panel

ANTENNA

CABLE

M.P.I.

VIDEO IN

DC IN

L - AUDIO - R

L - Audio - R

Page 13

206-3898

PAGE 13

For cable box operation, leave the VCR and the television tuned to channel three or four and use the cable box to change channels.

Cable Service w/VCR Hookup

Connect cable service and a VCR to the LCD TV/Monitor

Locate the Antenna/Cable jack on the back of the VCR.

Connect the cable service wire to the VCR. Connect other wires according to the diagram to the right.

Plug in the TV. The LCD-TV is designed to operate on DC power.

After all external connections are complete, go to page 19 to run Auto Program.

Cable TV Wall Jack

output

switch

Cable Box

Out

3 4

Cable TV Wall Jack

VCR Back

VCR Back AV Panel

output

switch

Video

Out

3 4

L - Audio - R

M.P.I.

CABLE

ANTENNA

Connections Panel

L - AUDIO - R

DC IN

VIDEO IN

Page 14

PAGE 14

206-3824

DC Power Hookup

Connect the TV to DC power directly or use the optional AC/DC power converter

12 Volt DC Power Hookup

The LCD-TV is designed to operate on 12V DC power.

Locate the DC input on the back of the LCD TV/Monitor.

Insert the DC power supply connector into the DC in port on the TV as shown to the right.

After all connections have been made. Go to page 19 to run Auto Program.

Optional AC to DC Power Converter

Power

Supply

CABLE

ANTENNA

M.P.I.

L - AUDIO - R

DC IN

VIDEO IN

Page 15

206-3886

PAGE 15

Front Panel Controls Operation

captions

vol

power

captions

vol

power

TV Operation

Press the POWER button to turn the LCD TV/Monitor on from standby mode.

Use the ch (Channel) button to cycle through the available channels.

Use the vol (Volume) button to adjust the sound level to your preference.

Press captions repeatedly to select a closed captions option or turn Off.

Captions Operation

Use captions to select the closed captions mode:

Off, C1, C2, C3, C4. Typical closed captions are broadcast on C1, if available on program.

On-Screen Displays

See descriptions on page 17. On-screen displays will appear when the feature is active or the function is being used.

Using the front control panel to operate the LCD TV/Monitor

Note: The TV master switch must be set to ‘

I’

for the TV to be in standby mode.

Not

functional

Page 16

PAGE 16

206-3898

On-Screen Menus Overview

ON-SCREEN MENUS

SETUP MENU Adjusts the basic operational features of the TV

Auto Program 19 Automatically finds and stores active channels to scroll through using Channel Up/Down.

Add/Del/Blnk 20 Manually picks and chooses which active channels will appear when using Channel Up/Down

Channel Labels 21 Labels the channels with their network names (ABC, CBS, HBO, etc.).

Clock Set 22 Sets the time.

Timer 23 Sets times for the TV to turn itself on and off each day.

Caption/Text 24 Chooses a captioning or text option.

Language 25 Picks the language the on-screen menus will appear in.

AUDIO MENU 26 Customizes the sound. Options are:

Bass, Treble, Balance, Audio Mode, Front Surround, SoundRite, Speakers.

VIDEO MENU 27 Adjusts the picture appearance. The options are: Contrast, Brightness, Color, Tint, Sharpness, Picture Pref.

PARENTAL 28/48 Allows installer/user to block program content for up to 12 hours, with the use of a password.

CONTROL MENU

17 OTHER MENUS AND ON-SCREEN DISPLAYS

Channel/Time Shows the current time, channel, (or video source), type of incoming audio signal, and XDS* info if provided.

Alarm Sets a time the TV will turn itself on.

Sleep Timer Sets a time the TV will turn off.

Volume Shows current sound level.

Captions Selects Caption/Text options.

Ch Preview Displays the available channels and menus list.

Channel Bank Shows currently selected channel bank.

INSTALLER MENUS

Installer Menus 34 Makes adjustments to the TV’s operational features.

*XDS (Extended Data Service) Additional program information provided at the discretion of the broadcaster. May include: title of broadcast, elapsed time, and time remaining on program.

Descriptions of the menus and on-screen displays available to the installer

Menu Name Page Description

Page 17

206-3824

PAGE 17

Other Menus & On-Screen Displays

PRESS DIGITS TO SET TIME

TIMER TO SELECT AM/PM

ALARM MENU

TIME NOW 3:11 PM

TIMER

6:10 AM

TIMER

CHANNEL PREVIEW• 5 - - - 9 - - - 20 - - - 32 - - - 44 - - - AUX - - - -

CC FOR PARENTAL CONTROL

CH TO SELECT, ENTER TO QUIT

VOLUME•

Press the remote keys indicated below to access these menus and displays

CHANNEL BANK

BANK 3

CAPTION 1 IS ON

Sleep Timer Menu

Press TIMER. Sets a time to automatically turn the TV off and shows remaining time before TV shutoff.

Volume Display

Press VOLUME. Shows currently selected sound setting.

Alarm Menu

Press ALARM. Sets a time the TV will turn itself on.

Ch Preview Menu

Press CH PREVIEW. Displays list of the available TV Channels, Guest Parental Control menu (if active) and Video Channel access. Press CHANNEL Up/Down to select a channel, or menu, then ENTER to go to channel or menu.

Closed Captions Menu

Press CC. Turns selected option on or off. See Caption/Text page to select options.

Channel Banks Menu

Press SOURCE/BANK on an Installer remote equipped with those keys. Accesses the Channel Banks menus: Bank 1, Bank 2, Bank 3, Bank 4.

Ch 25 - PBS

7:15

OLD TIME MOVIES

LENGTH 01:00 TIME LEFT 00:36

Rating: TV-14

Channel/Time Display

Press ENTER. Shows currently selected channel or source, current time if the clock has been set, incoming audio signal, and XDS data if provided by broadcaster.

Page 18

PAGE 18

206-3898

Installer Remote Key Functions

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

remote control part number

LP702

124-213-04

FLASHBK (FLASHBACK)

Returns to the last channel viewed.

POWER

Turns TV On or Off

CHANNEL (UP/DOWN)

Chooses next available channel.

MUTE

Turns sound Off and On, while the picture remains.

ENTER

Press to view the Channel/Time display or to remove any on-screen display or menu.

TIMER

Press repeatedly to adjust TV turn-off time

from 10 minutes up to 4-hours.

Sets AM or PM in Clock/Alarm menus.

VOLUME (LEFT/RIGHT)

Adjusts the sound level.

CC (CLOSED CAPTIONING)

Direct access to closed captions.

Press ENTER to exit.

A quick list of the keys on the optional LP702 installer’s remote and what they do

ALARM

Press to go to the Alarm menu. Set a time for the TV to turn itself on.

MENU/SELECT/ADJ (ADJUST)

Adjusts on-screen menus and options.

Press MENU repeatedly to scroll through

menus. Use SELECT to choose an option

and ADJ (adjust) Left/Right to change

the selected option.

CHANNEL PREVIEW

Gives installer access to the guest’s menus. Displays the available TV channels and hotel guest’s Parental Control menu (if active). Selects the Video source. (Use the Audio/Video jacks on the back of the TV as the source of the picture and sound.)

TV/FM

Selects TV or Radio mode on TVs equipped

with FM radio.

NUMBER KEYPAD

Used to key-in numbers and select channels directly: key-in channel numbers and press ENTER to go to new channel

Page 19

206-3898

PAGE 19

Auto Program (Channel Search)

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

3/5

AUTO PROGRAM ADD/DEL/BLNK CH. LABELS CLOCK SET TIMER CAPTIONS LANGUAGE

TO PROGRAM

4/6

7 2

Use Auto Program to specify Antenna or cable service incoming signal source and automatically store all of the channels that are found by channel search

With the optional Installer remote control in hand, press the POWER key to turn the TV on.

Press MENU repeatedly until the Setup menu appears.

Using SELECT on the remote control, highlight Auto Program on the screen.

Press the Right or Left ADJ (Adjust) arrow to go to the Auto Program menu.

Using SELECT, choose CABLE TV or OFF AIR ANTENNA on the menu. (The highlighted option is selected.)

Press the Right or Left ADJ arrow to begin the Channel Search.

Press ENTER when finished.

Mini glossary

OFF-AIR-ANTENNA If the end user can only view over-the-air broadcasts, select Off Air Antenna.

CABLE If you provide cable service to the end user, select Cable TV.

Auto Program finds channels being received by the TV tuner.

Cable will not work unless a cable service is present.

Page 20

PAGE 20

206-3824

Channel Add/Del/Blank Menu

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

3/4

CH 44 ADDED

TIMER

Fine-tune the user’s channel selection list

Press the MENU key repeatedly on the Installer’s remote until the Setup menu appears.

Press SELECT repeatedly to highlight the Add/Del/Blnk option.

Using either the NUMBER keypad and ENTER or the Channel Up/Down arrow on the remote, select a channel. (If adding a deleted channel, you will need to use the NUMBER keypad and ENTER.)

Using the Right/Left ADJ arrow, specify whether that channel is Added, Deleted, or Blank.

To continue, select another channel and repeat Step 4. When you are finished, press ENTER to remove menu.

Adding Aux, VCR 3, VCR 4, to the Channel Preview List

Go to the Setup menu, select the Add/Del/Blnk option. Use Channel Up/Down to select the option and choose Added. Note: If the option was turned off in the Service menu, you will have to reinstate it before it can appear as an option in the Channel Preview list.

Note: You can specify Add, Delete or Blank for VCR3, VCR4, and Aux. Caution: If you delete CH3, VCR3 is also

deleted, if you delete CH4, VCR4 is also deleted and vice versa.

If you delete a channel, it isn’t gone for good. Just select it using the NUMBER keypad on the remote, or add it later.

Mini glossary

ADD Adds new channels to the list that the guest can scroll through when using the remote.

DELETE Removes channels for one reason or another from the list that the guest can scroll through.

BLANK Removes the video signal from a channel so the guest will only receive the audio signal.

Page 21

206-3824

PAGE 21

Setting Up Channel Labels

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

AUTO PROGRAM ADD/DEL/BLNK CH. LABELS CLOCK SET TIMER CAPTIONS LANGUAGE

CH 32 ABC

SETUP MENU

Overview

Channel Labels help the user identify the channel or network being viewed. In the Setup menu with the CH LABELS option highlighted, use the ADJ

Left/Right arrow to scroll through the available channel labels, such as, A&E, AMC, ESPN, HBO, etc. These are a series of alphabetically organized preset labels from which you can choose the more common networks. Use any of these or create custom labels.

- - - - , The 4 dashes will allow a channel label to appear; if one is provided by XDS. (Extended data service)

NONE, prevents any channel label from appearing. LAB 1, thru LAB 20, are the 20 programmable labels.

The 20 programmable labels can be customized for your needs. Each programmable label has 5 characters spaces available.

To Program a Channel Label

First select a channel using the NUMBER keypad and ENTER or the Channel Up/Down arrow, on the optional Installer’s remote control.

(To select a deleted channel, use the NUMBER keypad and ENTER.) To program a channel label, go to the Setup menu and select CH LABELS. Use the Right/Left ADJ adjust arrow to scroll the available preset labels.

Scroll past - - - -, scroll past NONE, to go to the first programmable label slot, LAB 1. Notice that the label appears with the title LAB 1, and is also on a dark background; which will distinguish it from the preset labels.

Operating the Menu

Use Volume Up/Down to select the first letter. Press MUTE to clear the label if necessary. Use Channel Up/Down to change the character to one of the 255 characters

available. (A blank letter space is available if required, after the “!” symbol.)

ADJ (Adjust) Left/Right Switches to the next label.

- - moves to the next or previous label.

Volume Up/Down Selects character spaces

- - moves to the next or previous character space.

Channel Up/Down Scrolls through the available

characters.

ENTER Accept the channel label and

removes the menu.

MUTE Removes current label,

- - if first character space is selected.

You can press and hold down Channel Up/Down to scroll through the available characters rapidly.

Page 22

PAGE 22

206-3824

Setting the Clock

TIMER

CH PREVIEW

ENTER

ALARM

ADJ

SELECT

Mini glossary

TIME A four-digit figure broken down into hours and minutes, used to enter the current time when setting the clock or wake-up alarm.

HOURS First two digits that are entered when setting the clock or the wake-up alarm.

MINUTES The last two digits that are entered when setting the clock, or the wake-up alarm.

TIMER Chooses AM or PM when setting the clock.

The clock can also be set using 24 hour “military time.” For p.m. settings add 1200. For example, to set 6:30 p.m., add 1200 to 630, = enter 1830.

For Auto Clock Set to work, TV must be tuned to a channel that has XDS data available. Auto Clock Set, sets the time only once while the TV is on. To set the clock with XDS data, turn TV off, then back on again, or set the clock time manually.

AUTO EASTERN CENTRAL

MOUNTAIN

PACIFIC

CLOCK MENU

CLOCK SET TIME ZONE DAY. SAVING

USE SELECT TO CHOOSE USE ADJ TO CHANGE

AUTO

OFF ON

10:43 AM

CLOCK MENU

CLOCK SET TIME SET

USE SELECT TO CHOOSE USE ADJ TO CHANGE

MANUAL

TIMER

AUTO PROGRAM ADD/DEL/BLNK CH. LABELS CLOCK SET TIMER CAPTIONS LANGUAGE

SETUP MENU

TO SET CLOCK

AUTO PROGRAM ADD/DEL/BLNK CH. LABELS CLOCK SET TIMER CAPTIONS LANGUAGE

SETUP MENU

TO SET CLOCK

Clock Auto/Manual Operating Modes Setup

Use MENU, SELECT, and ADJ Left/Right to choose the Clock menu and to set up the clock menu options, with the optional Installer’s remote.

Clock Mode Auto: TV automatically sets the time.

Time Zone: Installer can choose the time zone or have the TV set it automatically. Day. Savings: Installer can choose to have daylight savings adjust the clock time one hour, or have the TV adjust it automatically.

Manual: User sets the time on the clock.

Use ENTER repeatedly to remove menus.

Page 23

206-3824

PAGE 23

ON TIME 9:00 AM

OFF TIME 7:00 PM

ON/OFF TIMER

TIMER

AUTO PROGRAM ADD/DEL/BLNK CH. LABELS CLOCK SET TIMER CAPTIONS LANGUAGE

TO SET TIMER

SETUP MENU

Set up On/Off Timers Note: On/Off Timers operate independently of each other.

On the optional Installer’s remote, press MENU repeatedly until the Setup menu appears.

Press SELECT repeatedly to highlight the Timer option, press the Right arrow.

Use SELECT to choose an option. Use the number keypad and/or the Left/Right ADJ arrows to enter the times. Use the TIMER key to set AM/PM.

Press ENTER to remove menu and return to TV viewing.

Your options are:

• On Time Sets a time that the TV will turn itself On each day.

• Off Time Sets a time that the TV will turn itself Off each day.

• On/Off Timer Enables or disables the On/Off Timer functions. (The On/Off Timer can be disabled but the settings will be retained.)

The clock must be set before the Timers will function.

The Off Timer can be used to turn the TV off at the preset time. Note: No On Timer setting is required to use the Off Timer feature.

Mini glossary

TIME A four-digit figure broken down into hours and minutes, used to enter the time when setting the clock or programming timers.

HOURS First two digits that are entered when setting the clock or programming timers.

MINUTES The last two digits that are entered when setting the clock, or programming timers.

TIMER Choose AM or PM with the TIMER button when setting the clock.

Timer

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

Page 24

PAGE 24

206-3824

Captions (Caption/Text)

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

Standard closed captioning is available using the Caption 1 option.

CAPTION 1 CAPTION 2 CAPTION 3 CAPTION 4

TEXT 1 TEXT 2 TEXT 3 TEXT 4

OFF

CAPTIONS SETUP

OPER. MODE SEL. TYPE CAPTION LOCK

PRESS SELECT TO CHOOSE PRESS ADJ TO CHANGE

STANDARD

ON, OFF

CAPTION 1 CAPTION 2 CAPTION 3 CAPTION 4

TEXT 1 TEXT 2 TEXT 3 TEXT 4

TO SET CAPTIONS

CAPTIONS SETUP

OPER. MODE SEL. TYPE CAPTION ON MUTE CAPTION LOCK

PRESS SELECT TO CHOOSE PRESS ADJ TO CHANGE

QUICK/MUTE

ON, OFF

AUTO PROGRAM ADD/DEL/BLNK CH. LABELS CLOCK SET TIMER CAPTIONS LANGUAGE

SETUP MENU

TO SET CAPTIONS

AUTO PROGRAM ADD/DEL/BLNK CH. LABELS CLOCK SET TIMER CAPTIONS LANGUAGE

SETUP MENU

Mini glossary

CAPTIONS The term for the words that scroll across the bottom of your TV screen; usually the audio portion of the program

provided for the hearing impaired.

TEXT The term for the words that appear in a large black frame and almost cover the entire screen; usually messages

provided by the broadcaste

Set up Closed Caption/Text options for the user

Closed Captions/Text Operating Modes Setup

Use MENU, SELECT, and ADJ Left/Right to choose the Closed Captions/Text mode and to set up the other menu options for the user.

Quick/Mute When CC is pressed: User can only turn Captions on/off.

(If CC on Mute is on, shows captions option on mute.) (If locked, type is retained with Power on/off.)

Standard When CC is pressed: User can choose a captions type.

(If locked, type is retained with Power on/off.)

Press ENTER repeatedly to remove menus.

Caption/Text are features which allow the Concierge TV to receive the closed caption and/or text options if made available by the broadcaster. Availability and functionality of Caption/Text options are determined only by each broadcaster and may not be available in your area.

Page 25

206-3824

PAGE 25

Language

AUTO PROGRAM ADD/DEL/BLNK CH. LABELS CLOCK SET TIMER CAPTIONS LANGUAGE

ENGLISH

SETUP MENU

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

Choose the language for the on-screen menus

Press the MENU key repeatedly on the installer’s remote control until the Setup menu appears.

Use SELECT on the remote control to highlight the Language option on the menu.

Use the Right/Left ADJ arrow to choose one of the following options: English, Spanish or French.

Press ENTER to return to TV viewing.

Page 26

PAGE 26

206-3824

Audio Menu

BASS TREBLE BALANCE AUDIO MODE FRONT SURR SOUNDRITE AUDIO PREF

STEREO

OFF OFF

CUSTOM

AUDIO MENU

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

2/4

Mini glossary

STEREO SOUND Stereo (stereophonic) sound refers to audio that’s divided into right and left sides.

MONO SOUND Mono (monaural) sound is one channel of sound. On more than one speaker, all the speakers play the same audio.

SOUNDRITE Maintains a constant volume level when commercials or channel changing increases or decreases the sound level.

Adjust the audio options for the end user

Not all programming is broadcast in stereo sound or has 2nd Audio SAP.

Press MENU repeatedly on the installer’s remote control until the Audio menu appears.

Using SELECT on the remote control, highlight the setting you want to change. Choose from:

• Bass: Increases/decreases lower-end sounds.

• Treble: Increases/decreases higher-end sounds.

• Balance: Allows you to put the sound more to the left or

right channel.

• Audio Mode: Chooses from Stereo sound, Mono, or 2nd Audio/SAP.

• Front Surround: Turns Front Surround sound on or off.

• Soundrite: Turns the uniform volume feature on or off.

• Audio Preference: Chooses Custom or Preset audio set-

tings. (Preset returns settings to default values.)

Use the Right/Left ADJ arrow to adjust or change the option you have selected.

Press ENTER to return to TV viewing, or press SELECT and return to the Audio Menu to adjust another option.

Page 27

PAGE 27

206-3824

Video Menu

CONTRAST BRIGHTNESS COLOR TINT SHARPNESS PICTURE PREF

PRESET

VIDEO MENU

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

2/A

3/B

Press MENU repeatedly until the Video menu appears. Your options are:

• Contrast: Adjusts the level of difference between white and black in the TV picture. The more contrast, the brighter the picture appears.

• Brightness: Increases or decreases amount of white in the TV picture.

• Color: Adjusts levels of all colors in the TV picture.

• Tint: Balances between amounts of red and green in the TV

picture.

• Sharpness: Raises or lowers the definition of the TV picture. The lower the level, the softer the images will appear.

• Picture Preference: Choose either Custom or Preset. Custom allows you to set the picture the way you want. Preset moves all the above options back to their original, factory-set levels.

Use SELECT on the installer’s remote control to choose Contrast on your screen.

Use the Right/Left ADJ arrow to change the contrast level to custom settings.

Press ENTER, or MENU one more time to return to TV viewing, or repeat from step two to set the other menu options.

Use SELECT to choose Picture Preference on your screen.

Use the Right/Left ADJ arrow, to choose either the original settings with Preset, or use your own settings with Custom.

Choose the Preset option in Picture Preference to quickly reset the levels to their original values.

Use the Video menu to customize the picture appearance

Page 28

PAGE 28

206-3824

Reset Parental Control Block Hours to Zero and Cancel Password

This provides the institution staff and the installer a means to reset the TV to normal operation, if an end user has either forgotten the password or has left Parental Control Block active after turn off.

On the installer’s remote control, press and hold down MENU until the menu disappears (about 6 seconds). Immediately press 9, 8, 7, 6 and then CC. (Based on 0-I INST. SEQ. ‘0’ setting.) This will reset the Block Hours to Zero and cancel the current 4-number password.

Installer Parental Control Menu

Overview

To insure complete coverage for all TV programs, (movies and regular TV shows) choose a rating for MPAA, from the selections below AND choose ratings from the TV Parental Guidelines Rating System on pages 48 and 49, using the Age Block option for General Audiences, and for Children. In addition to those, you may wish to add additional restrictions from the Content Block menu. See the Parental Control menu, and submenus example on the next page.

Things to Consider before Setting Up Parental Control

Determine which rating you consider acceptable to the viewer. (For example, if you choose TV-PG, all more restrictive ratings will be automatically blocked; the viewer will not be able to see: TV-PG, TV-14, or TV-MA rated programming.)

Do you want the auxiliary video source signal blocked? (Block the picture and sound of the equipment, such as a VCR, connected to the TV Audio/Video input jacks; in the Aux. Block option.) Or leave unblocked, and Parental Control will restrict the video input based on the restrictions you have specified.

Block program “Content” based on individual parameters such as: Strong Dialog, Bad Language, Sex Scenes, Violence Scenes, or Fantasy Violence Scenes; in the Content Blk option.

How many hours do you want Parental Control to be active? You can set the option for up to 12 hours. (See next page.)

Select a secret password; in the Set Password option. Use the number keys on the remote. If you forget the password, see note below.

Do you want Parental Control to be active all the time? If not, you can turn it on or off; with the Lock On/Off option.

If used, this optional feature can “block” undesirable programming from appearing on the TV

You should set different Parental Control viewing restrictions for general audiences and for children - - both should be active at the same time

Simply specifying one content block such as Sex Scenes, will not automatically block another content in the programs from appearing.

Parental Control offers the user a wide variety of options and settings that restrict or “block” the programming that can appear on the TV. Parental control allows the user the capability of defining which program rating they consider acceptable, to the younger or more sensitive viewer. It can be preset and turned either on or off by the user who specifies the secret 4-number code, the password. The number of hours blocked are specified. General audience and children viewer blocks should both be programmed into the TV’s memory. Viewer ratings are specified for both TV and the motion picture industry; both rating systems can be used. The ratings are based mainly on the ages of children.

You cannot disable Parental Control by disconnecting the TV from power. Block hours remaining will be retained if power is lost or power cord is disconnected.

The AUX input source can also be blocked.

Page 29

PAGE 29

206-3824

Installer Parental Control Menu

After you have read the preceding page, follow instructions below to set up and activate Parental Control

SETUP MENU

AUDIO MENU

DIALOG LANGUAGE SEX SCENES VIOLENCE F VIOLENCE NO RATING

TO BLOCK

GENERAL CHILDREN

AGE BLOCK

UNBLOCKED

CONTENT BLOCK

TO BLOCK

AUX SOURCES MPAA RATING AGE BLOCK CONTENT BLK SET HOURS SET PASSWORD LOCK ON OFF

PARENTAL CONTROL

VIDEO MENU

PRESS CC TO RETURN

Note: Use the installer’s remote control to specify Parental Control settings.

Press MENU repeatedly until the Parental Control Menu appears.

As shown above, with the Parental Control menu on-screen, use SELECT to choose an option, like Content Block.

Use the Left/Right ADJ arrow to show the Content Block menu, to adjust or set the rating for an option. For Sex Scenes for example, use the “From TV-PG” setting. (See the Mini Glossary, Ratings Charts on pages 48 and 49 for rating meanings.)

After you have selected and adjusted the parental control menu options to your preferences:

- Set the number of hours Parental Control will be on.

- Set a 4-number password.

- Set the Lock On/Off option to either on or off.

Note: Some broadcasts and videotapes do not include rating information.

TIMER

CH PREVIEW

ENTER

ALARM

ADJ

SELECT

Make Parental Control restrictions permanent, with no preset or fixed hours time limit

In the Installer’s Menu, Item 84: PERMANENT BLK, 0 or 1. 0 Blocking restrictions always active, no time limit.

1 Restrictions limited to specified hours, 12 - 99.

Reset the Maximum Number of Parental Control Default Block Hours

You can change the Block hours from the 12-hour default setting to up to 99 hours. In the Installer’s Menu, item: 22-I MAX BLK HRS 12,

use the ADJ Left/Right adjust arrow to set a different default number of hours.

To Turn the Parental Control Feature Off/On

In the Installer’s Menu, Items: 21-I V-CHIP, 0 or 1, 51-I DIS. VCHIP M., 0 or 1

Options Setups for V-Chip Menu and Block Functions

21-I V-CHIP 51-I DIS. VCHIP M. 0 0 No menu, no blocking. 0 1 No menu, no blocking. 1 0 Shows menu, Block functions. 1 1 No menu, Block functions.

Page 30

Unblocked Blocked

General Children

Unblocked G and Above PG and Above PG-13 and Above R and Above NC-17 and Above X

Dialog Language Sex Scenes Violence F Violence No Rating

TO BLOCK

Unblocked TV-PG and Above TV-14 and Above TV-MA

Unblocked TV-Y7

Unblocked Blocked

Unblocked TV-G and Above TV-PG and Above TV-14 and Above TV-MA

Unblocked TV-Y and Above TV-Y7

00 Hours

To Set

Enter Code: - - - -

On Off

PAGE 30

206-3824

Note

Reset Parental Control Block Hours to Zero and Cancel Password

This provides the institution staff and the installer a means to reset the TV to normal operation, if a user has either forgotten the password or has left Parental Control Block active.

On the installer’s remote control, press and hold down MENU until the menu disappears (about 6 seconds). Immediately press 9, 8, 7, 6 and then CC. This will reset the Block Hours to Zero and cancel the current 4-number password.

Make Parental Control restrictions permanent, with no preset or fixed hours time limit

In the Installer’s Menu, Item 84: PERMANENT BLK, 0 or 1. 0 Blocking restrictions always active, no time limit.

1 Restrictions limited to specified hours, 12 - 99.

Reset the Maximum Number of Parental Control Default Block Hours

You can change the Block hours from the 12-hour default setting to up to 99 hours. In the Installer’s Menu, item: 22-I MAX BLK HRS 12,

use the ADJ Left/Right adjust arrow to set a different default number of hours.

To Turn the Parental Control Feature Off/On

In the Installer’s Menu, Items: 21-I V-CHIP, 0 or 1, 51-I DIS. VCHIP M., 0 or 1

Options Setups for V-Chip Menu and Block Functions

21-I V-CHIP 51-I DIS. VCHIP M. 0 0 No menu, no blocking. 0 1 No menu, no blocking. 1 0 Shows menu, Block functions. 1 1 No menu, Block functions.

Installer Parental Control Menu

Page 31

PAGE 31

206-3824

PLANNING THE CHANNEL BANKS

Generally, TV channels are grouped into “program packages” with terms that are proposed to the end user. The user then opts for a package. Below is an example of how TV channels may be grouped.

You may plan your package by using a chart like the one after the following page.

Remember, you can “blank” a channel for accommodating audio-only, such as an FM radio station or in-house communication.

Sometimes, only one or two channel banks may be needed. You may leave any unused bank with the channels entered during Auto Program; or, you may delete the channels. However, you may want to leave at least one channel in any unused bank. Then, if someone selects an “unused” bank, that channel will assure them that the TV is functional.

Note: Some channels from factory testing may be in the channel banks if you have not yet run Auto Program.

ADDING / DELETING CHANNELS

A previously prepared programming chart is helpful.

1. Run Auto Program (in the Setup menu). All channels found on your cable/antenna will be entered in Channel Banks 1, 2, 3, and 4. Note: Be advised that running Auto Program overwrites any custom channel setups; removes Blanked, Deleted.

2. Select a channel bank with an installer remote - -press SOURCE/BANK (and repeat). CHANNEL BANK and BANK number will be displayed.

3. Use the ADD/DEL/BLNK option (also in the Setup menu) to customize your program package. You may delete channels or add some that have not been entered. You can also “Blank” a channel for accommodating an audio-only program source or in-house communication. See the “ADD/DEL/BLNK” menu page for more details. Note: The Blank Channel feature is global. A channel will be blanked in all channel banks.

4. Repeat steps 2, and 3 to program another channel bank.

Managing the Channel Banks

The TV has four channel banks, where the administrator or installer can store groups of TV channels Note: Channel banks set up requires an installer’s remote with “Source” or “Bank” keys like the optional Zenith MBR3447, or a similar remote.

Channel Bank Program package

1 Basic cable channels 2 Extended cable channels 3 Extended with premium channels 4 Other cable service options

(Grouping is provided as an example only.)

The BLNK (blank) channel function is “global” -- the same channel number is blanked in channel banks 1, 2, 3, and 4.

Channel Bank Number Display

CHANNEL BANK

BANK 1

Page 32

PAGE 32

206-3824

B Purpose Channel Number

A 12345678910111213141516171819202122232425

N K

1 A A A A AAAAAAA AAAA 2 A A A A AAAAAAA AAAA 3 A A A A AAAAAAA AAAA 4 A A A A AAAAAAA AAAA

B Purpose Channel Number

A 12345678910111213141516171819202122232425

N K

1 Basic BC A AAAADDDDDDDD DDDD 2 Extend BC A AAAAADAADAAADDDD 3 All CTV BC A AAAAADAADAAAADAA 4 Other BC A AAAAAAAAAAAA AAAA

ADDING / DELETING CHANNELS

It is best to do ADD / DEL customizing before doing “BLNK.”

AUTO PROGRAM enters the same channels in banks 1, 2, 3, and 4.

AUTO PROGRAM removes any channels previously customized with ADD / DEL / BLNK. The channels available on your antenna / cable will be entered, and any channels previously entered but not currently available will be deleted.

ADD and DEL (not BLNK) can be used independently for channel banks 1, 2, 3, and 4.

A channel blanked, is blanked in all channel banks.

Channel allocations in tuning bands:

BROADCAST: 2 – 69 CABLE – CATV, HRC or ICC: 1 – 125

A = Active - - Channel was found during AUTO PROGRAM

A = Active Channel was found during AUTO PROGRAM D = Deleted Channel was deleted using Add/ Del option. BC = Blanked Channel Channel was blanked using BLANK channel option (ADD/DEL/BLNK).

Managing the Channel Banks

Examples of typical channel banks charts filled in

Figure 1. Typical channel banks after running Auto Program

Figure 2. Typical channel banks after running Auto Program, and customizing with Add/Del/Blnk

Page 33

PAGE 33

206-3824

PLAN YOUR CHANNEL BANKS BY FILLING IN THESE CHARTS (or use photocopies)

B Purpose Channel Number A 12345678910111213141516171819202122232425 N K

1 2 3 4

B Purpose Channel Number A 26272829303132333435363738394041424344454647484950 N K

1 2 3 4

B Purpose Channel Number A 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 FM N K

1 2 3 4

B Purpose Channel Number A 51525354555657585960616263646566676869707172737475 N K

1 2 3 4

B Purpose Channel Number A 767778798081828384858687888990919293949596979899100 N K

1 2 3 4

Managing the Channel Banks

Page 34

PAGE 34

206-3824

Installer menus

Menu Item Function Value Range Default Value Brief Description of Function and Comments

0-I INSTALLER SEQ 0 - 3 0 Leave default set 0. 1-I POWER MANAGE 0 - 7 0 Sets number of hours of no activity before auto shutoff. 2-I AC ON 0 / 1 0 Set to 1 to enable auto turn on at power up. 3-I BAND/AFC 0 - 7 0 Tuning band, see detailed descriptions. 4-I STRT CHANNEL 0 - 255 255 Channel at turn-on (255 last Channel viewed at turn off). 5-I CHAN LOCK 0 / 1 0 When set to 1, cannot tune from current channel. 6-I GHOST CH. 0 / 1 0 Set to 1 to enable Ghost Channel display. 7-I START VOLUME 0 - 63, 255 255 Volume level at TV turn-on (Set 255 to retain last volume level). 8-I MIN VOLUME 0 - 63 0 Minimum volume setting.

9-I MAX VOLUME 0 - 63 63 Maximum volume setting. 10-I MUTE DISABLE 0 / 1 0 Set to 1 to disable mute function. 11-I KEY DEFEAT 0 / 1 1 Set to 1 to disable Menu, Select, and Adj keys on front panel. 12-I IR BANKS EN. 0 / 1 0 Set to 1: enables TV to respond to IR codes to change channel bank directly. 13-I SCAN MODE 0 / 1 0 Puts On-Off in Ch Up/Down sequence. 14-I STRT CH IN SM 0 / 1 0 Set to 1 to put TV On/Off below start channel number. 15-I SLEEP TIMER 0 / 1 1 Set to 1 to enable Sleep Timer. 16-I EN TIMER 0 / 1 1 Set to 1 to enable Timer. 17-I ALARM 0 / 1 1 Set to 1 to enable Alarm. 18-I NOT USED 19-I NOT USED 20-I FEATURE LEVEL 0 / 1 1 Zen 1 Leave default set 1 (1 Zen 1) 21-I V-CHIP 0 / 1 1 Set to 1 to enable V-Chip 22-I MAX BLK HRS 0 - 99 12 Select number of Parental Control blocking hours. 23-I CAPTION LOCK 0 / 1 0 Set to 1 to retain Caption setting at turn off. 24-I TEXT MODE 0 / 1 1 Set to 1 to add Text option to closed caption menu. 25-I FUNCTION PRE 0 - 3 0 Controls channel preview in Pay-Per-View function menu.

Use the Installer Menu to set up or change operational settings See descriptions of the Installer items on the following pages...

0IMCRM1038A 01.83 01

0-I INST. SEQ. 0

SN: XXXX-XXXXXXXX UPN: XXX-XXX-XXX-XXX

XX/XX/XX TE = 10110000

Accessing the Installer’s Menu

Installer’s menu items can be accessed by using the optional LP702 installer’s remote control. Just press and hold MENU (about 8 seconds) until the display changes, then press 9, 8, 7, 6, then ENTER. To exit the Installer’s Menu, press ENTER again. Any

changes you make will be stored in nonvolatile memory.

The Installer’s menu opens with item 0-I, INST. SEQ. Use the SELECT key to sequence through the available menu items. Or, access an item directly by entering the line number, then pressing MENU. For example, to access the Sleep Timer option which is on line 15-I, press 15, then MENU. To change a setting use the Left/Right ADJ keys.

Using the Installer’s Menu

Items 0-I - 86-I are immediately accessible only upon entering the Installer’s Menu. Their numbers, descriptions, ranges, factory default settings, and a place for listing any changes made on-site are given below and on the following pages. A Factory Menu that is intended for qualified service technicians only, is not shown. Normally Factory menu items do not require adjustment.

Installer Menu Items 0-I through 25-I

XX-F Menu Items (Not shown here) are servicetype adjustments and only qualified technicians having specialized test equipment should access them.

Typical Installer Menu

Page 35

PAGE 35

206-3824

Installer menus

Menu Item Function Value Range Default Value Brief Description of Function and Comments

26-I NOT USED 27-I NOT USED 28-I CH. OVER RIDE 0 / 1 1 When set to 0. limits direct access to favorite channels. 29-I OLD OCV 0 / 1 0 OCV should set to 1. 30-I ACK MASK 0 / 1 0 M.P.I. communication parameter. 31-I POLL RATE 20 - 169 94 M.P.I. communication parameter. 32-I TIMING PULSE 186 - 227 207 M.P.I. communication parameter. 33-I NOT USED 34-I CAMPORT EN. 0 / 1 0 Set to 1 to enable the front AUX (Camport) input. 35-I NOT USED 36-I NOT USED 37-I REAR Y/C EN. 0 / 1 0 Set to 1 to enable the rear S-Video input. 38-I NOT USED 39-I NOT USED 40-I AUTO CAMPORT 0 / 1 0 Set to 1 to automatically switch to Camport. 41-I NOT USED 42-I NOT USED 43-I AUTO REAR Y/C 0 / 1 0 Set to 1 to automatically switch to rear S-Video input. 44-I NOT USED 45-I NOT USED 46-I STRT AUX SRCE 0 - 2, 255 255 Set the starting AUX source 47-I AUX STATUS 0 / 1 0 Set to 1 for M.P.I. AUX source reported as Channel number instead of Channel 0. 48-I DIS. SETUP M. 0 / 1 0 Set to 1 to disable Setup menu. 49-I DIS. AUDIO M. 0 / 1 0 Set to 1 to disable Audio menu. 50-I DIS. VIDEO M. 0 / 1 0 Set to 1 to disable Video menu. 51-I DIS. VCHIP M. 0 / 1 0 Set to 1 to disable V-Chip (Parental Control) menu. 52-I DIS. SOURCE M. 0 / 1 0 Set to 1 to disable Source menu. 53-I DIS. CH-TIME M. 0 / 1 0 Set to 1 to disable Channel-Time display. 54-I EN. SET. COL. 0 / 1 0 Set to 1 to enable custom color for Setup menu. 55-I FOR. SETUP M. 0 - 7 6 Custom foreground color for the Setup menu. 56-I BCK. SETUP M. 0 - 7 4 Custom background color for the Setup menu. 57-I EN. AUDIO COL. 0 / 1 0 Set to 1 to enable custom color for the Audio menu. 58-I FOR. AUDIO M. 0 - 7 1 Custom foreground color for the Audio menu. 59-I BCK AUDIO M. 0 - 7 7 Custom background color for the Audio menu. 60-I EN. VIDEO COL. 0 / 1 0 Set to 1 to enable custom color for the Video menu. 61-I FOR. VIDEO M. 0 - 7 4 Custom foreground color for the Video menu. 62-I BCK VIDEO M. 0 - 7 7 Custom background color for the Video menu. 63-I EN. PTL. COL. 0 / 1 0 Set to 1 to enable custom color for the V-Chip (Parental Control) menu.

Installer Menu Items 26-I through 63-I

Page 36

PAGE 36

206-3824

Installer menus

Installer Menu Items 64-I through 86-I

Menu Item Function Value Range Default Value Brief Description of Function and Comments

64-I FOR. PTL. M. 0 - 7 6 Custom foreground color for the V-Chip (Parental Control) menu. 65-I BCK. PTL. M. 0 - 7 4 Custom background color for the V-Chip (Parental Control) menu. 66-I EN. SRC. COL. 0 / 1 0 Set to 1 to enable custom color for the Source menu. 67-I FOR. SRC. M. 0 - 7 3 Custom foreground color for the Source menu. 68-I BCK. SRC. M. 0 - 7 4 Custom background color for the Source menu. 69-I EN. CH-T COL. 0 / 1 1 Set to 1 to enable custom color for the Channel-Time display. 70-I FOR. CH-T COL 0 - 7 1 Custom foreground color for the Channel-Time display. 71-I BCK. CH-T COL 0 - 7 1 Custom background color for the Channel-Time display. 72-I NOT USED 73-I CH NOT AVBLE 0 / 1 0 When set to 1 and channel override is 0, “NOT AVAILABLE” message is displayed

when direct accessing a channel not in the favorite channel list.

74-I CH-TIME SIZE 0 / 1 0 When set to 1 and transparent background is selected for Channel-Time display,

(foreground color = background color and custom color enabled) a large channel

number is displayed instead of the normal Channel-Time display. 75-I NOT USED 76-I DEFEAT XDS 0 / 1 0 When set to 1, XDS display program information will not appear. 77-I NOT USED 78-I UPN MSB 0 - 255 255 User programmable number, most significant byte. (Line-Day) 79-I UPN MSB-1 0 - 255 255 User programmable number, most significant byte - 1. (Week) 80-I UPN MSB-2 0 - 255 255 User programmable number, most significant byte - 2. (SN-HIGH) 81-I UPN LSB 0 - 255 255 User programmable number, least significant byte. (SN-LOW) 82-I CHKSM ERROR 0 / 1 0 Enforces rigid M.P.I.* checksum. 83-I HANDSHK TIME 0 - 5 0 Relaxes M.P.I. timing to be compatible with PC based Windows controlled systems. 84-I PERMANENT BLK 0 / 1 0 Remove block hours setting for Parental Control and make blocks permanent.

85-I. A. MUTE TIME 0 - 254 50 Controls muting audio delay time when switching between AUX sources. 86-I. V. MUTE TIME 0 - 254 50 Controls muting video delay time when switching between AUX sources.

*M.P.I. Multiple Protocol Input: Zenith protocol for remote control of TV through RJ11 (M.P.I.) jack on TV connections panel.

Detailed Descriptions of Installer Menu Items

0-I. INSTALLER SEQUENCE

Gives access to Installer Menu depending on the code selected.

0 = 9876 1 = 4321 2 = 1478 3 = 3698

1-I. POWER MANAGE (Power Management)

Determines hours of no activity before automatic shutoff. The POWER MANAGE function is for saving energy. When set to 0, Power Manage is OFF. Settings range from 0 - 7, with 1 - 7 repre-

senting the hours that the TV will remain on, unless there has

been activity from either the control panel or remote control.

2-I. AC ON (AC Power Switchable)

Allows the TV to turn ON just by applying AC power. Pressing the

ON button is not necessary. This is desirable when the TV is

plugged into a cable box or a power outlet controlled by a wall

switch. Use ADJUST to select 0 or 1, where 0 is the default is

OFF, and 1 is ON.

NOTE: When set to 1 (ON), the TV does not respond to ON/OFF

commands from either the remote or the control panel, and the

SLEEP TIMER is also nonfunctional.

Page 37

PAGE 37

206-3824

Installer menus

Installer Menu Items 3-I through 11-I: Detailed Descriptions

3-I. BAND/AFC (Band/Automatic Frequency Control)

There are 8 possible settings for this option:

0 = Broadcast Fixed 4 = Broadcast AFC 5 = CATV Fixed 1 = CATV AFC 6 = HRC Fixed 2 = HRC AFC 7 = ICC Fixed 3 = ICC AFC

Channels are accessed faster when fixed modes are used. The AFC (search modes) should only be used when some channels are not on nominal frequencies. NOTE: BAND is automatically set by AUTO PROGRAM.

If some channels were not found by AUTO PROGRAM, select the appropriate AFC setting here and add the channels using the ADD/DEL option in the Setup Menu.

4-I. STRT CHANNEL

When active, this function allows you to determine the initial channel number when the TV is turned ON. This feature is useful for an in-house information channel, since the TV would always select that channel when it is turned on. Setting this to 255 causes the last channel viewed when TV was turned off to be the tuned to channel when the TV is turned on again.

The range of values is 0 - 255. Use (adjust) keys to choose numbers that determine the start channel.

5-I. CHAN LOCK (Channel Lock)

CHAN LOCK is ideal if a cable box (or similar) is the sole source for programming—and the TV must always be on the same channel. Changing channels with Channel Up/Down or keypad numbers is impossible. Channel Lock is inactive when set to 0 (default).

Generally, this feature is used in conjunction with START CHANNEL (item 4-I.) where the start channel may, for example, be set to 3 or 4. If the start channel is 3 then the TV will remain on channel 3. NOTE: When CHANNEL LOCK is active and CHANNEL OVERIDE is disabled, AUTO PROGRAM is not active.

6-I. GHOST CH (Ghost Channel)

When set to 1, the current channel number is displayed in the upper right corner of the CRT. The number moves slightly to pre-

vent damage to the screen. The default is “0” or OFF. NOTE: When captions are on, the “Ghost Channel” is not displayed.

7-I. START VOLUME

This function allows the Installer to determine the initial volume level setting when the TV is turned ON. This feature is useful for an in-house information channel, since the TV would always select that volume level when it is turned on. The range of values are 0 - 63, 255. If 255 is selected, the current volume level will be retained in memory when the TV is turned off; at TV turn on, volume level is automatically set to the previous or last level.

8-I. MIN VOLUME (Minimum Volume)

This function determines the minimum volume level allowable with the VOLUME (VOL) Up/Down control. In this way, for example, someone cannot set the volume too low to hear. The range is from 0 to 63—change values with ADJUST. The factory default is 0, which provides full range of volume control. It may be best to set the same value on every TV. NOTE: The minimum volume level cannot have a value setting higher than in the MAX VOLUME level (described below).

9-I. MAX VOLUME (Maximum Volume)

This function determines the maximum volume level allowable with the VOLUME VOL Up/Down control. In this way, for example, someone cannot set the volume level high enough to disturb others. The range is 0 to 63, with 63 as the default which gives the user the full range of volume control. Change values with ADJUST keys. It may be best to set the same value on every TV. NOTE: The maximum volume level cannot have a value setting lower than the MIN VOLUME level (described above).

10-I. MUTE DISABLE

Enables or disables sound mute function. Set to 1, sound cannot be muted. Set to 0, sound can be muted.

11-I. KEY DEFEAT (Keyboard Defeat)

When set to 1, it prevents the end user from accessing screen menus on the front panel—MENU, SELECT, and ADJUST do not function. When set to 0, those keys are functional. The menus can always be accessed with MENU on the remote.

Page 38

PAGE 38

206-3824

12-I. IR BANKS EN.

For direct access to a particular Channel Bank. When enabled, installer can access a channel bank by inputting the IR code for the bank.

13-I. SCAN MODE

Allows variation in setting the On/Off with Channel UP/DOWN. You may opt for TV channels only; TV channels + Off/ON with these settings for Scan Mode:

Scan mode Characteristics

0 Channel up/down keys change channels only.

1 Channel down below the lowest channel (or

channel up higher than the highest) and TV turns off.

14-I. STRT CH IN SM

When set to 1, installs TV on/off event below the start channel at TV turn on.

15-I. SLEEP TIMER

When set to 1, the SLEEP TIMER feature may be used (but no message is displayed prior to turn-off). When set to 0, the sleep timer is not available.

16-I. EN. TIMER

Set to 1, timer function is available to user. Set to 0 to disable Timer functions. (Clock must be set in order to use Timers.)

17-I. ALARM

Gives you the option of making the alarm function available to the user. Set to 1, alarm function is available to user. Set to 0 to disable the Alarm function. Note: Clock must be set in order to set the Alarm.

18-I. NOT USED

19-I. NOT USED

20-I. FEATURE LEVEL

Default set to ZEN 1 for Zenith IR remote control operation.

Set O, P LBL for Zenith Private Label IR remote control operation. Warning: Do not set to “0” or remote will not control TV.

21-I V-CHIP

Set to 1 to activate V-Chip (Parental Control); have it available

to user to filter or control or restrict programming content. Set

to 0 to turn V-Chip feature off, not available to user; no pro-

gramming restrictions can be set.

22-I. MAX BLK HRS

Set to 0 to 99 for the maximum V-Chip (Parental Control) block

hours. Default is 12 blocking hours.

23-I. CAPTION LOCK

Set to 1 to restore previous caption On/Off state after TV turns

off. When set to 0, captions are always off, when TV is initially

turned on.

24-I. TEXT MODE

Determines whether TEXT 1, TEXT 2, TEXT 3, or TEXT 4 decoding

is enabled when TEXT is turned on (either from the Setup Menu

or directly with CC on the remote).

TIP: Set Text Mode to 1 only if text is offered in your video

system.

25-I. FUNCTION PRE.

Set to 0 to suppress CHANNEL PREVIEW from the FUNCTION

menu with some Pay-Per-View systems.

26-I. NOT USED

27-I. NOT USED

28-I. CH. OVERRIDE (Channel Override)

When set to 1, the user can select channels with either Channel

Up/Down or by direct keypad entry. When set to 0, only those

channels that are entered for scanning may be selected by direct

keypad entry. Note: If set to 0, Auto Program is locked; (as

shown on Setup menu) you cannot do a channel search.

29-I. OLD OCV (On Command Video

)

Set to 1 for operation with systems from On Command

Corporation.

30-I. ACK MASK

M.P.I. Communication Parameter. Leave at default setting unless

changed by Pay-Per-View provider.

31-I. POLL RATE

M.P.I. Communication Parameter. Leave at default setting unless

changed by Pay-Per-View provider.

Installer menus

Installer Menu Items 12-I through 31-I: Detailed Descriptions

Installer should leave item 20-I. FEATURE LEVEL set to 1 (default).

Page 39

PAGE 39

206-3824

Installer menus

Installer Menu Items 32-I through 57-I: Detailed Descriptions

32-I. TIMING PULSE

M.P.I. Communication Parameter. Leave at default setting unless changed by Pay-Per-View provider.

33-I. NOT USED

34-I. FRONT AUX ENABLE

Set to 1 to enable the front AUX (Camport) input. Set to 0 to disable front AUX input.

35-I. NOT USED

36-I. NOT USED

37-I. REAR Y/C EN.

Set to 1 to enable the rear S-Video input. Set to 0 to disable the rear S-Video input.

38-I. NOT USED

39-I. NOT USED

40-I. AUTO CAMPORT

Set to 1 to automatically switch to camport when equipment is connected to front Video input. Set to 0 to disable front Video automatic source selection.

41-I. NOT USED

42-I. NOT USED

43-I. AUTO REAR Y/C

Set to 1 to automatically switch viewing source to rear S-Video input when equipment is connected. Set to 0 to disable rear S-Video automatic source selection.

44-I. NOT USED

45-I. NOT USED

46-I. STRT AUX SRCE

Sets the starting AUX source.

47-I. AUX STATUS

Set to 1 for M.P.I. AUX source to be reported as a channel number instead of channel 0. Set to 0 to disable AUX identification change.

48-I. DIS. SETUP M.

Set to 1 to disable the Setup menu. Setup menu will not appear. Set to 0 to enable the Setup menu.

49-I. DIS. AUDIO M.

Set to 1 to disable the Audio menu. Audio menu will not appear. Set to 0 to enable the Audio menu.

50-I. DIS. VIDEO M.

Set to 1 to disable the Video menu. Video menu will not appear. Set to 0 to enable the Video menu.

51-I. DIS. VCHIP M.

Set to 1 to disable the Parental Control menu. Parental Control menu will not appear. Set to 0 to enable the Parental Control menu.

52-I. DIS. SOURCE M.

Set to 1 to disable the Source menu. Source menu will not appear. Set to 0 to enable the Source menu.

53-I. DIS. CH-TIME M.

Set to 1 to disable the Channel-Time display. Channel-Time display will not appear. Set to 0 to enable the Channel-Time display.

54-I. EN. SET. COL.

Set to 1 to enable custom color settings for the Setup menu. Set to 0 to disable custom color settings for the Setup menu.

55-I. FOR. SETUP M. (Setup Menu Foreground Color) Set according to Color Chart. 0 = Black 3 = Yellow 6 = Cyan 1 = Red 4 = Blue 7 = White 2 = Green 5 = Violet

56-I. BCK. SETUP M. (Setup Menu Background Color) 0 = Black 3 = Yellow 6 = Cyan 1 = Red 4 = Blue 7 = White 2 = Green 5 = Violet

57-I. EN. AUDIO. COL.

Set to 1 to enable custom color settings for the Audio menu. Set to 0 to disable custom color settings for the Audio menu.

Page 40

PAGE 40

206-3824

Installer menus

Installer Menu Items 58-I through 76-I: Detailed Descriptions

58-I. FOR. AUDIO. COL. (Audio Menu Foreground Color) 0 = Black 3 = Yellow 6 = Cyan 1 = Red 4 = Blue 7 = White 2 = Green 5 = Violet

59-I BCK. AUDIO. COL. (Audio Menu Background Color) 0 = Black 3 = Yellow 6 = Cyan 1 = Red 4 = Blue 7 = White 2 = Green 5 = Violet

60-I. EN. VIDEO. COL.

Set to 1 to enable custom color settings for the Video menu. Set to 0 to disable custom color settings for the Video menu.

61-I. FOR. VIDEO M. (Video Menu Foreground Color) 0 = Black 3 = Yellow 6 = Cyan 1 = Red 4 = Blue 7 = White 2 = Green 5 = Violet

62-I. BCK. VIDEO. COL. (Video Menu Background Color) 0 = Black 3 = Yellow 6 = Cyan 1 = Red 4 = Blue 7 = White 2 = Green 5 = Violet

63-I. EN. PTL. COL.

Set to 1 to enable custom color settings for the V-Chip menu. Set to 0 to disable custom color settings for the V-Chip menu.

64-I. FOR. PTL. M. (V-Chip Menu Foreground Color) 0 = Black 3 = Yellow 6 = Cyan 1 = Red 4 = Blue 7 = White 2 = Green 5 = Violet

65-I. BCK. PTL. M. (V-Chip Menu Background Color) 0 = Black 3 = Yellow 6 = Cyan 1 = Red 4 = Blue 7 = White 2 = Green 5 = Violet

66-I. EN. SRC. COL.

Set to 1 to enable custom color for the Source menu. Set to 0 to disable custom color for the Source menu.

67-I. FOR. SRC. M. (Source Menu Foreground Color) 0 = Black 3 = Yellow 6 = Cyan

1 = Red 4 = Blue 7 = White 2 = Green 5 = Violet

68-I. BCK. SRC. M. (Source Menu Background Color) 0 = Black 3 = Yellow 6 = Cyan 1 = Red 4 = Blue 7 = White 2 = Green 5 = Violet.

69-I. EN. CH-T COL.

Set to 1 to enable custom color for the Channel-Time display. Set to 0 to disable custom color for the Channel-Time display.

70-I. FOR. CH-TIME (Channel-Time Display Foreground Color) 0 = Black 3 = Yellow 6 = Cyan 1 = Red 4 = Blue 7 = White 2 = Green 5 = Violet Note: If foreground and background color are the same, menu background is transparent.

71-I. BCK. CH-TIME (Channel-Time Display Background Color) 0 = Black 3 = Yellow 6 = Cyan 1 = Red 4 = Blue 7 = White 2 = Green 5 = Violet Note: If foreground and background color are the same, menu background is transparent.

72-I. NOT USED

73-I. CH NOT AVBLE

When set to 1 and channel override is set to 0, “NOT AVAILABLE” message is displayed when direct accessing a channel not in the favorite channel list.

74-I. CH-TIME SIZE

When set to 1 and transparent background is selected for Channel-Time display, (foreground color = background color and custom color enabled) a large channel number is displayed instead of the normal Channel-Time display

75-I. NOT USED

76-I. DEFEAT XDS

Set to 1 to disable XDS display. Set to 0 to enable XDS display.

Page 41

PAGE 41

206-3824

Installer menus

Installer Menu Items 77-I through 86-I: Detailed Descriptions

77-I. NOT USED

78-I. UPN MSB

User programmable number, most significant byte readable by M.P.I. command. (Line - Day)

79-I. UPN MSB-1

User programmable number, most significant byte-1 readable by M.P.I. command. (Week)

80-I. UPN MSB-2

User programmable number, most significant byte-2 readable by M.P.I. command. (SN-HIGH)

81-I. UPN LSB

User programmable number, least significant byte readable by M.P.I. command. (SN-LOW)

82-I. CHKSM ERROR

Enforces rigid M.P.I. checksum validation. Set to 1 for validation. Set to 0 to turn off.

83-I. HANDSHK TIME

Adds an additional delay to the handshake time which is 64 msec, thus relaxing M.P.I. timing requirements to be compatible with PC based Windows controlled systems, range is 0 - 5. Set to 0 to retain standard 64 msec delay. Set to 1 - 5 to increase @ 16 msec ea., the delay up to 144 msec.

84-I. PERMANENT BLK

Allows Parental Control blocking schemes to be permanent by removing the blocking hours function. Set to 1 to install Parental Control blocking restrictions permanently. Set to 0 for user-specified hours control of blocking schemes.

85-I. A. MUTE TIME

Controls audio muting delay time when switching between AUX sources. The audio will be muted for 16 msec times the value of this setting.

86-I. V. MUTE TIME

Controls video muting delay time when switching between AUX sources. The video will be muted for 16 msec times the value of this setting.

Page 42

PAGE 42

206-3824

LT2000 QuickSet Programmer

A slow flashing green light indicates there is a problem with the communications between the TV and the programmer. In this case, check for a damaged cable, poor contacts, or other connection troubles.

If the status indicator is red, the programmer batteries are low and should be replaced. Use 4 good-quality alkaline AA batteries.

Use the Zenith LT2000 QuickSet II “Clone” Programmer to copy the setup from a “master” TV then quickly transfer the setup to duplicate TVs must be the same model number as the master TV

The optional QuickSet II Clone Programmer (LT2000) allows custom setup and programming information to be quickly copied from a master TV into multiple identical television sets. Once learned from the master, setup data is retained in the LT2000 for future use.

When using the LT2000, cloning operations will go easier if the TV set is connected to a good quality signal and operating with a stable picture displayed. To operate the LT2000, use the indicated keys on an HP602, LP702, or MBR3447 remote, or the front panel keys on the TV receiver.

Clone Controlling TV Display

Before you begin...

• The “master TV” should be connected to a good, stable signal from an over-the-air antenna or cable service and turned on.

• Teaching and Learning is only possible between identical model Zenith TVs. (However, the Clone programmer can store 4 different master TV setups.)

WARNING: Copying a blank or incorrect memory into a TV will cause the TV to operate erratically or become inoperable.

• Use a Zenith MBR Remote like the MBR3447 or the TV front panel controls to operate Learning and Teaching menus.

• Make sure that the batteries in the Clone programmer are fresh.

• If the batteries are removed, the Clone Clock time will be lost.

• Decide if you want to set the time from the Clone programmer or copy the time to the Clone programmer; from a TV which has the clock set to the current time.

• Follow the connection diagrams above to connect the Clone to a master TV and, after learning is complete, to another TV to “teach” it the setup.

• Setting the time and transferring it to the Clone or another TV is a separate procedure.

• Once a TV’s setup is copied to another TV, that TV needs to be disconnected from power for about 5 seconds to activate the newly copied setup.

• See Troubleshooting to solve problems.

A. Set Up a Master TV

Using a Zenith Multi-Brand remote like the MBR3447, set up a “master” TV with custom settings and features as described in the master TV’s operating guide. The master TV’s Setup is what you will copy to the Clone Programmer and transfer to TVs of the same model so they will operate identically.

B. Connect Clone to Master TV

If there is a good connection, the “Clone has Control of TV” message will appear. (See menu above.)

Learn Master TV

Typical MPI Connections

Teach Other TV

Typical MPI Connections

Antenna

RF Coaxial Wire

(75ohm)

RF Coaxial Wire

(75ohm)

M.P.I.

THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION XX

THE TV IS VERSION XX THE SW IS REVISION XX

CLONE CLOCK = XX:XX TV CLOCK = XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

CABLE

ANTENNA

QuickSet II Programmer

LT2000

Clone

L - AUDIO - R

VIDEO IN

DC IN

M.P.I.

CABLE

ANTENNA

QuickSet II Programmer

LT2000

Clone

L - AUDIO - R

VIDEO IN

DC IN

Page 43

PAGE 43

206-3824

Clone Selection Menu Choices

Typical Clone on-screen menus

C. Learn Setup from Master TV

Press 1 to select the “Learn From TV” option, then press ON/OFF, POWER, or ENTER to go to the Memory Bank Selection Menu. Pick the Memory ”Bank” (1, 2, 3, or 4) you want to store this Master TV’s Setup in by pressing either Channel key repeatedly to pick Memory 1, 2, 3, or 4. (If you choose a Memory “Bank” that already has a master TV’s setup already in it, it will be overwritten by this Master TV’s setup.) Once the Clone memory bank is selected, press ON/OFF, POWER, or ENTER. The Clone memory bank you have selected will be shown. Press ON/OFF or POWER to begin copying the master TV’s setup.

Ca. Set the Clock (Optional)

Set the time on the Master TV’s Clock. (If the time has already been copied from another TV into the Clone programmer, you can set the Master TV’s clock by copying the time from the Clone programmer.) The Clone Programmer can copy the current time to both a master TV and to the Clone’s internal clock; accurate to within one minute. (Another reason that the Clone programmer should be equipped with fresh, high-quality alkaline batteries is for it to keep the time as accurately as possible.) Since the Clone Programmer’s time cannot be set directly, the time needs to be copied from a Zenith TV equipped with M.P.I. input capability.

Once the time is copied to the Clone programmer, the current time can then be transferred to another TV. (This can be a Master TV, or another TV which has had the features already set up.)

D. Teach Master TV’s Setup to Other TV

Once Learning is complete, remove the M.P.I. cable from the master TV and connect it to the TV that you want to copy the master TV’s setup to. With the “TV is Controlled by Clone” message displayed, press 2 or use either Channel key to go to the “Teach to TV” option, press ON/OFF, POWER, or ENTER. Follow on-screen instructions to transfer the Setup and other information to the “Learning” TV. After the “Teach to TV is Complete” message is displayed, press any key to return to the Clone menus option, then press ON/OFF, POWER, or ENTER. If finished, remove M.P.I. cable from the TV.

E. Disconnect TV Power for 5 Seconds

Remove the TV power cord of the newly “Cloned TV” from the power outlet for about 5 seconds to activate the newly copied setup.

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION XX THE TV IS VERSION XX THE SW IS REVISION XX

CLONE CLOCK= XX:XX TV CLOCK= XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

CLONE SELECTION MENU

(1) LEARN FROM TV (2) TEACH TO TV (3) SET CLONE CLOCK FROM TV (4) SET TV CLOCK FROM CLONE (5) DISPLAY TV SETUP (6) DISPLAY CLONE SETUP

-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER

Page 44

Clone Selection Menu Choices

Operation Notes

Disconnect the Clone from the TV when you are finished; automatically switching it off. The real-time clock continues to run when the main circuits are switched off.

Reset Clone After Static Shock

After replacing exhausted batteries, or if the programmer behaves strangely after a static shock, use a paper clip or similar instrument inserted through the small hole marked ”RESET” to activate the internal reset switch and restore normal operation. After a reset, check the real-time clock setting. It may be necessary to reset the Clone Programmer clock from a TV containing the correct time.

The LT2000 programmer is designed to be used with TVs contain-

ing the 221-01006 and later processors. Use with earlier TV sets

may give unpredictable results. The specific microprocessor used

in any TV set may be determined by activating the Installer

Menu. The microprocessor part number appears at the top of the

screen when the Installer Menu is activated. Processors before

the 221-01006-04 have a limited screen display capability. They

can not display entire screens as shown in the quick setup

instructions accompanying the LT2000 clone programmer. Use the

printed menu illustrations on the quick setup sheet supplied with

the Clone as an aid to making your programming choices.

(Although the menus are not all displayed, the clone functions

all operate normally.)

When cloning operations are complete, just unplug the LT2000 from the TV.

If the TV does not display a picture (blank screen) after a few seconds, just change channels.

Troubleshooting

Problem Possible Cause(s) Possible Solution(s)

Clone Programmer

LED does not blink. • M.P.I. cord not connected. -Connect M.P.I. cord.

• TV not turned on. -TV must be on for clone to work.

• Weak batteries. -Install 4 fresh AA high-quality alkaline batteries.

Clone menu hard • Weak signal. -Connect TV to a reliable signal source. to read.

No time set. • No time on master TV. -Set time on master TV, copy time to Clone Programmer.

Menu items 7-8 not • Not necessary. -Channel Labels already cloned; if they were on master TV. on clone selection menu.

Master and Other TVs

Cloning did not work. • Procedure interrupted. -Wait until procedure complete message is displayed.

• Different TV models. -Cloning is only possible with identical model TVs.

Clone time disappeared. • Batteries were removed. -Batteries must remain installed to retain time settings.

Channel Labels not • Saved to other memory. -Must save channel labels to same memory bank as present on cloned TV. master TV setup.

New Setup not present. • TV not reset. -Disconnect newly cloned TV from power for 5 seconds.

PAGE 44

206-3824

Page 45

PAGE 45

206-3489-O

Routine TV cabinet and screen cleaning

Maintenance

1. Here’s a great way to keep the dust off the screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen.

2. Make sure the excess water is off the screen, and then let it air-dry before turning the TV on.

1. Use a soft cloth with a mild soap solution to wipe the cabinet. (Avoid using any harsh, industrial strength variety of cleaner.)

2. Rinse the cloth and wipe the cabinet again.

3. Let the cabinet air-dry before turning the TV on.

Use a quality wood cleaner and polish. This will protect the TV from dirt and dust, as well as keep the cabinet looking new.

If the TV is to be left dormant for a long time, it’s a good idea to unplug the power to protect against possible damage from lightning or power surges. If you use an off-air antenna, you may also want to disconnect it from the back of the TV.

Screen Cleaning

Minimal Usage

If you unplug the TV, you may have to reset the clock using the Clock Set menu described earlier. See page 22.

Cabinet Cleaning

Wood Cabinet

Careful and regular cleaning can extend the the useful service life of the TV. Be sure to turn the power off and pull out the plug before you begin any cleaning.

Page 46

SYMPTOMS

Snowy picture and unclear sound.

Multiple images or ‘ghost shadows.’

Interference: Sharp lines across the screen and poor sound.

Normal picture but no sound.

No picture and unclear sound.

No picture and no sound.

No color, but the sound is O.K.

Picture has a big black box on it, but the sound is O.K.

Remote control doesn’t work.

Menu options can’t be changed or selected.

No picture or sound when any non-cable source is selected.

No XDS Display.

Troubleshooting

Some quick and easy tips to resolving problems

POSSIBLE SOLUTION(S)

• Check the antenna connection or location.

• Check the cable input.

• Check to see if the TV/VCR button on the VCR has the TV selected.

• Check the antenna direction and/or location.

• Check the cable input.

• Make sure the wire from the antenna to the TV is properly connected.

The following may cause image problems or distortion: Electrical appliances, powerful lights, cars, trucks; computers or portable phones; medical equipment

• If possible, increase the distance between the TV and the offending appliance.

Or turn one of them off.

• Check volume levels.

• Make sure the TV sound is not Muted.

• Try another channel. The problem may be the broadcast, not your TV.

• Are the Audio A/V cables properly installed?

• Are the wires for external speakers (if you have external speakers) properly installed?

• If the audio mode is set to SAP, that channel may not have a SAP program.

• Make sure output channels on all A/V equipment are on the same channel (3 or 4).

• Check that all connections are tight.

• Is the AC power cord plugged in?

• Check that your AC power outlet works. (Test it by plugging in another device or try another outlet.)

• Make sure brightness and audio controls are set properly.

• Try another channel. The problem may be with the broadcast.

• Check the picture settings in the Video menu.

• Try another channel. The problem may be with the broadcast.

• The CC (closed caption) option may be in Text mode. Select Caption 1, or OFF in the Captions menu.

• Make sure the batteries are fresh and installed properly (see page 10).

• Try unplugging the TV power cord for a few minutes, then plugging it back in.

• Check to see if the source equipment has been turned on.

• Make sure that the connections are secure on the back of the TV and on the

source equipment.

• XDS data will only appear if provided by the broadcaster.

PAGE 46

206-3824

Page 47

206-3898

End User Remote Key Functions

TIMER ALARM

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

remote control part number

SC652Z

124-213-18

6710V00108A

FLASHBK (FLASHBACK)

Returns to the last channel viewed.

POWER

Turns TV On or Off

CHANNEL (UP/DOWN)

Selects next available channel, and the Video Channel (Audio/Video source).

MUTE

Turns sound Off and On, while the picture remains.

ENTER

Press to view the

Channel/Time/Audio display or to

remove any on-screen

display or menu.

NUMBER KEYPAD

Used to key-in numbers and select channels directly: key-in channel numbers and press ENTER to go to new channel

TIMER

Press repeatedly to set the TV turn-off

time from 10 minutes up to 4-hours.

Chooses AM/PM in the Alarm menu.

VOLUME (LEFT/RIGHT)

Adjusts the sound level.

CHANNEL PREVIEW

Displays the available TV channels, including access to guest’s Parental Control menu (if Active). Allows guest to select the Video source. (Use the Audio/Video jacks on the back of the TV as the source of the picture and sound.)

CC (CLOSED CAPTIONING)

Direct access to closed captions.

Press ENTER to exit.

A quick list of the keys on the optional end user remote for L20V34S and what they do

ALARM

Press to display menu, then follow on-screen instructions to set a time for the TV to turn itself on.

NOTE:

The channel and volume keys can be used by the end user to select and adjust the Parental Control settings, if the installer activates the Parental Control option in the Installer menus.

PAGE 47

Page 48

End User Parental Control Menu

Mini glossary

MOTION PICTURE ASSOCIATION OF AMERICA (MPAA) RATING SYSTEM

G General Audiences Content not offensive to most viewers. PG Parental Guidance Content is such that parents may not want their children to view the program.

Suggested

PG-13 Parental Guidance Program is inappropriate for preteens, with a greater degree of offensive material

Suggested than a PG rated program. R Restricted viewing Not for children under age 17. Strong elements of sex and/or violence. NC-17 Restricted Viewing Not for children under age 17 under any circumstances. Strong sexual content. X Hard Core Films Same as NC-17 rating.

Note: Zenith Electronics Corporation is not liable for any program content that appears when using this rating system; as always, user discretion is advised.

Overview

To insure complete coverage for all TV programs, (movies and regular TV shows) choose a rating for MPAA, from the selections below AND choose ratings from the TV Parental Guidelines Rating System on the next page, using the Age Block option for General Audiences, and for Children. In addition to those, you may wish to add additional restrictions from the Content Block menu. See the Parental Control menu, and submenus example on the next page.

Things to Consider before Setting Up Parental Control

Do you want the auxiliary video source blocked entirely? (Block the content of the equipment, such as a VCR, connected to the TV Audio/Video input jacks; in the Aux. Block option.) Or leave unblocked, and Parental Control will restrict the video picture and sound based on the restrictions you have specified.

Block program “Content” based on individual parameters such as: Strong Dialog, Bad Language, Sex Scenes, Violence Scenes, or Fantasy Violence Scenes; in the Content Blk option.

How many hours do you want Parental Control to be active? You can set the Hours option for up to 12 hours.

Select a secret password; in the Set Password option. Use the number keys on the remote. Don’t forget the password, it is the only way you can access the Parental Control menu and change rating selections, or turn Parental Control off.

Do you want Parental Control to be active all the time? If not, you can turn it on or off; with the Lock On/Off option.

This optional feature can be used to “block” undesirable programming from appearing on the TV

You should set Parental Control viewing restrictions for general audiences and for children - - both should be active at the same time.

Simply specifying one content block such as Sex Scenes, will not automatically block another content in the programs from appearing.

If you choose to have the Aux inputs unblocked, the ratings you specify will automatically restrict the programming that appears from the video sources.

You cannot disable Parental Control by disconnecting the TV from power. Block hours will automatically reset to the original block time setting specified if power is disconnected.

This TV offers the user a wide variety of options and settings that restrict or “block” the programming that can appear on the TV. Parental control allows the user the capability of defining which program rating they consider acceptable, to the younger or more sensitive viewer. It can be preset and turned either on or off by the user who specifies the secret 4-number code, the password. The number of hours blocked are specified. General audience and children viewer blocks should both be programmed into the TV’s memory. Viewer ratings are specified for both TV and the motion picture industry; both rating systems can be used. The ratings are based mainly on the ages of children.

206-3824

PAGE 48

Page 49

End User Parental Control Menu

Mini glossary

TV PARENTAL GUIDELINE RATING SYSTEM

TV-G General Audience Considered suitable for all audiences; children may watch unattended.

TV-PG Parental Guidance Suggested Unsuitable for younger children, may contain: Suggestive Dialog, Bad Language, Sex, and Violence Scenes.

TV-14 Parents Strongly Cautioned Unsuitable for children under 14, may contain: Strong Dialog, Bad Language, Sex, and Violence Scenes.

TV-MA Mature Audience Only Adults only, may contain: Strong Dialog, Bad Language, Sex, and Violence Scenes.

CHILDREN’S CLASSIFICATIONS

TV-Y Children Considered suitable for all children under 7 years old.

TV-Y7 Children 7 and over Considered suitable for children over 7, may contain Fantasy Violence Scenes.

After you have read the preceding page, follow instructions below to set up and activate Parental Control

TO BLOCK

CHANNEL PREVIEW• 5 - - - 9 - - - 20 - - - 32 - - - 44 - - - AUX - - - -

CONTENT BLOCK

DIALOG LANGUAGE SEX SCENES VIOLENCE F VIOLENCE NO RATING

TV-MA

CC FOR PARENTAL CONTROL

CH TO SELECT, ENTER TO QUIT

PRESS CC TO RETURN

TIMER ALARM

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

4/6

Press CH PREVIEW.

Press CC to go to PARENTAL CONTROL menus.

Use CHANNEL Up/Down to highlight an option like CONTENT BLOCK.

Use VOLUME Up/Down to go to the CONTENT BLOCK menu.

Use CHANNEL Up/Down to highlight an option like SEX SCENES.

Use VOLUME Up/Down to choose: Unblocked, TV-PG AND ABOVE, TV-14 AND ABOVE, or TV-MA. (AND ABOVE means more restrictive headings are automatically included when you choose a low restriction setting like TV-PG.) See the Mini Glossary, Ratings Charts on this and the previous page for rating meanings.

After you have selected and adjusted the parental control menu options to your preferences:

- Set the number of hours Parental Control will be on.

- Set a 4-number password.

- Set the Lock On/Off option to either on or off.

Press ENTER to remove menu.

Note: some broadcasts do not contain rating information.

Note: The institution decides if the Parental Control feature will be available to the end user. If available, Parental Control will appear as an option in the CH (CHANNEL) PREVIEW menu.

3/5

206-3824

PAGE 49

Page 50

User Menus & On-Screen Displays

PRESS DIGITS TO SET TIME

TIMER TO SELECT AM/PM

ALARM MENU

TIME NOW 3:11 PM

TIMER

6:10 AM

TIMER

VOLUME•

CAPTION 1 IS ON

Press the remote keys indicated below to access these menus and displays

Sleep Timer Menu

Press TIMER. Press repeatedly to set the Sleep Timer. Shows remaining time before TV shutoff.

Volume Display

Press VOLUME. Shows currently selected sound setting.

Ch Preview Menu

Press CH PREVIEW. Displays list of the available TV Channels, Guest Parental Control menu (if active), and Video Channel access. Use CHANNEL Up/Down to select a channel, or menu, then ENTER to go to the channel or menu.

Closed Captions Menu

Press CC. Turns selected Caption/Text option on and off.

Alarm Menu

Press ALARM. Sets the time the TV will turn itself on. Use the number keypad and TIMER to set AM/PM.

CHANNEL PREVIEW• 5 - - - 9 - - - 20 - - - 32 - - - 44 - - - AUX - - - -

CC FOR PARENTAL CONTROL

CH TO SELECT, ENTER TO QUIT

Ch 25 - PBS

7:15

OLD TIME MOVIES

LENGTH 01:00 TIME LEFT 00:36

Rating: TV-14

Channel/Time Display

Press ENTER. Shows currently selected channel or source, current time if the clock has been set, incoming audio signal, and XDS data if provided by broadcaster.

206-3824

PAGE 50

Page 51

206-3886

PAGE 51

Front Panel Controls Operation

captions

vol

power

captions

vol

power

TV Operation

Press the POWER button to turn the LCD TV/Monitor on from standby mode.

Use the ch (Channel) button to cycle through the available channels.

Use the vol (Volume) button to adjust the sound level to your preference.

Press captions repeatedly to select a closed captions option or turn Off.

Captions Operation

Use captions to select the closed captions mode:

Off, C1, C2, C3, C4. Typical closed captions are broadcast on C1, if available on program.

On-Screen Displays

On-screen displays will appear when the feature is active or the function is being used.

Using the front control panel to operate the LCD TV/Monitor

Note: The TV master switch must be set to ‘

I’

for the TV to be in standby mode.

Not

functional

Page 52

Image-Persistence Cause & Prevention

Image-Persistence is rare on LCDs but is something of which you, the customer, should be

aware.

What is Image-Persistence?

A residual image from a previous screen is still viewable after changing channels/inputs.

Sometimes the after image will fade away in a few seconds/minutes, but it is possible that the

image is persistent and doesn’t fade away. This problem is most common on devices that use

phosphor in the screen, but can also affect LCDs. Although Image-Persistence takes longer to

happen on LCDs than with phosphor based displays, care should be taken to prevent

permanent effects. Image-Persistence is also known as “Image Burn-In”, “Image-Retention”,

and “Image-Sticking”.

What causes Image-Persistence on LCDs?

When an LCD TV or monitor is operated continuously for a long period of time with a fixed (non-

moving) image, a trace of electric charge can build up near electrodes inside the LCD module.

The result of this is a residual image of the previous image when the screen is changed.

How do I prevent Image-Persistence on my LCD?

• Turn the device off when not use.

• Do not leave static DVD or game menus on the screen for long periods of time.

• Use a screen saver and/or power save feature when using the LCD as a PC monitor.

• Change your PC’s background wallpaper periodically.

How do I reverse Image-Persistence on my LCD?

• Leave the device off for several hours/days.

• Display a white image on your screen for several hours/days.

• Use a screen saver that uniformly “exercises” each part of the screen.

NOTE: These methods do not guarantee that image burn-in will be reversible.

Is Image-Persistence covered by warranty?

No, this is considered misuse and is not covered by warranty. Normally, only product defects are

covered by warranty and Image-Sticking is inherent to the technology used to make the display.

Page 53

LCD-TV/Mon 1/03

206-3886

Issue *

For Customer Support/Service Please call:

1-888-865-3026

www.zenith.com

LCD TV/Monitor Welcome to the Zenith family! We believe that you will be pleased with your LCD TV/Monitor. Please read this warranty carefully, it is a

“LIMITED WARRANTY” as defined under Federal Law. This warranty gives you specific legal rights, and you may also have other rights that vary from state-to-state within the U.S.A.

ZENITH’S RESPONSIBILITY

Service Labor During a period of one year from effective warranty date, Zenith will provide service labor by a Zenith authorized service center when needed, as

determined by the Zenith service center, as a result of manufacturing defects.

Parts New or remanufactured replacements for factory-defective parts will be supplied by a Zenith authorized service center for one year from effective

warranty date (color picture tube — two years). Such replacement parts are warranted for the remaining portion of the original warranty period.

Warranty Service Warranty service is provided in the institution in most cases. (Some repairs may require the unit to be taken by the servicer to the repair facility and

returned, at no additional charge.) Call 1-888-865-3026 for further information.

Not Covered This warranty covers manufacturing defects and does not cover installation, adjustment of customer controls, installation or repair of antenna systems,

cable converters or cable company-supplied equipment; it also does not cover damage due to misuse, abuse, negligence, acts of God or other causes beyond the control of Zenith. Any alteration of the product after manufacture voids this warranty in its entirety.

THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND ZENITH SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INDIRECT, OR INCIDENTAL DAMAGES OF ANY KIND, INCLUDING LOST REVENUES OR PROFITS IN CONNECTION WITH THIS PRODUCT. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.

OWNER’S RESPONSIBILITY

Effective Warranty Date Warranty begins on the date of installation of the Commercial Products LCD TV/Monitor.

For your convenience, keep the dealer’s dated bill of sale or delivery ticket as evidence of the purchase date.

Operating Guide Read the Installation and Operating Guide carefully so that you will understand the operation of the unit and how to adjust the controls.

Antenna Reception problems caused by inadequate antenna or faulty antenna connections are the owner’s responsibility.

Important Product Registration—Please fill out and mail the Product Registration Card. It is imperative that Zenith know how to reach you promptly if we should

discover a safety problem that could affect you.

Warranty Service For warranty service information, call 1-888-865-3026. Parts and service labor that are Zenith’s responsibility (see above) will be provided without

charge. Other service is at the owner’s expense. If you have any problem in obtaining satisfactory warranty service, call 1-888-865-3026. You must provide the model number, serial number and date of purchase or date of original installation. Before you ask for warranty service, read “Troubleshooting” in this installation guide. You might avoid a service call.

Your Zenith LCD TV/Monitor Warranty

Zenith L10V34H, L10V34S Installation And Setup Manual

Specifications and Main Features

Frequently Asked Questions

User Manual