Zeiss 1847-316, 1907-605, 1907-593, 2008-996, 2008-992 User manual

...

Compact Prime and Zoom lenses

ZEISS Mount Change Instructions

A. Adjusting the ﬂange focal distance to the lens B. Overview

Congratulations on the purchase of this Compact Prime CP.2 lens set. We are convinced

that your new lenses will bring you much pleasure and success.

The Compact Prime CP.2 lenses are the latest members of the ZEISS family of lenses

for digital and ﬁlm cameras. They deliver great ﬂexibility by introducing interchangeable

mounts that allow the lenses to be used with a wide range of cameras, from traditional

cine to HDSLR systems. Available in ﬁve different mounts – PL, EF, F, Micro 4/3 and E –

this new family of ZEISS lenses enables cinematographers to be completely free in their

choice of camera systems. The Compact Prime CP.2 lenses cover the full-frame image

format without vignetting.

In this manual we take a Compact Prime CP.2 35mm/ T 2.1 with EF mount, scaled in feet

as an example to explain how to change a lens mount and the subsequent matching of your

lens to a DSLR camera. Proceed in the same sequences to switch to any other CP.2 mount.

General instructions

• The use of a T6 torque wrench with a torque of 0.4 Nm is strongly recommended.

This wrench can be purchased from Carl Zeiss (see appendix, page 17).

• Ensure that the environment is clean and free from dust so that no dust particles can

enter the lens during the following procedure.

• Smudges and ﬁngerprints on the lens surface can be gently removed with a soft brush

and then with a dry and clean cotton cloth. The ZEISS lens cleaning kit will give superior

results and is highly recommended for this purpose.

• When matching the lens, ensure that the colored shims lie on top of each other in the

groove of the lens barrel and do not cover the screw holes.

• Please handle the shims carefully as they can easily kink or tear which makes them unusable.

General drawing

Lens

Groove of the lens barrel

Shim

Adapter ring with attached silver support bracket

Mount including threaded black inner ring (e.g. EF)

Torx screws

2 3 4 5 6

C. Changing the mount

1. Remove the rear lens cap.

2. Remove the four torx screws of the silver EF mount with a T6 torque wrench

and place the mount and the screws on one side.

The size of the black inner ring depends on the focal length of the lens and is securely

fastened to the EF mount (or F, MFT or E Mount) at the factory.

4. Now you see the colored shims in the groove of the black lens barrel.

5. Place the PL mount on the lens in such a way that the groove on the rear side

of the PL mount ﬁts over the silver screw on the lens barrel.

6. Tighten the eight torx screws with the T6 torque wrench using a torque of 0.4 Nm.

3. Remove the eight torx screws of the black EF adapter ring and place the ring

and the screws on one side.

The silver support bracket is already installed on the EF adapter ring at the factory and does

not need to be removed.

7. When the torx screws have been tightened, the lens can be ﬁtted to a camera

with a PL mount and used.

8. Check the ﬂange focal distance of the lens (see section D) in combination with your camera.

screw of the lens barrel.

4 5

Instructions on changing to an EF or to any other CP.2 mount

1. Ensure that the groove on the rear side of the black EF adapter ring ﬁts over

the small screw of the lens barrel.

2. Place the silver EF mount on the EF adapter ring in such a way that the blue dot

on the mount has the same orientation as the ZEISS logo and the support bracket points

to the serial number on the lens barrel.

4. Please note the correct orientation of the Micro 4/3 and the E mount

to the serial number on the lens barrel.

5. Tighten the torx screws using a torque of 0.4 Nm.

3. Please note the correct orientation of the F mount to the ZEISS logo.

6 7

+ 7 hidden pages