We hope you enjoy your Zeraxa 2.0 Auto-Hovering Camera Drone from
RadioShack. Congratulations! No FAA Registration is required for this drone.
Please read this user’s guide before setting up and using your drone.
Features
• Detachable camera • Digital proportional control
• USB charging • 6-axis gyro stablilization
• 2.0 system upgrade with air pressure sensor for enhanced hovering
Package Contents
• Zeraxa 2.0 Camera Drone • Remote Control
• USB Charging Cable • Spare Propeller with screw (4)
• 3.7V Drone Battery • User’s Guide
Specifications
Power ...............................................................................................................................................
Maximum SD card support ...................................................................................... 32G
Specications are subject to change and improvement without notice. Actual
product may vary from the images found in this document.
Fly Safely
• Do not y the drone near or at other people or animals.
• Do not y your drone where emergency responders are working, or
emergency aircraft are operating.
• When ying outdoors, keep the drone away from power lines, trees, weeds,
and water.
• Do not y your drone over private property where you are not welcomed.
• When ying indoors, keep the drone away from walls, air conditioning, air
vents, fans, breakable objects, and other obstacles.
• Keep eyes, hands, hair, and loose clothing away from moving propellers.
• Fly safely. If the drone crashes, the SD card may fall out.
• Adult supervision is recommended at all times.
6001434_UG_EN.indd 37/6/2016 3:25:41 PM
CHOKING HAZARD! Small parts. Not for children under 3 years.
3
Charge the Drone Battery
Make sure you use the supplied battery and battery charging cable, or one
of the same type: 3.7 V, 530mAH lithium polymer.
1. Use the USB charging cable to connect the battery to a USB power
source. The LED on the USB connector lights red during charging, and
turns o when charging is complete.
LED
A full charge takes about 100 minutes. A fully charged battery provides up
to 7 minutes of ight and camera time.
2. After charging, unplug the USB charging cable. Do not attempt to
overcharge the battery.
3. To install the battery, use a
screwdriver to open the drone
battery compartment door.
4. Match and plug the two ends of the
white battery connectors. They
only t one way, so do not use force.
Neatly slot the battery and cables into
the compartment.
5. Screw the compartment door close.
Note: To recharge the battery, you can
leave the battery inside the drone. Simply unplug the battery connectors, then
follow steps 1-2 to charge using the supplied USB cable.
Lithium Battery Notes
• Do not charge longer than recom mended. Unplug the charging cable when
the battery is charged.
• Do not attempt to charge or operate damaged toys.
• Do not puncture or crush. Do not disassemble.
• Do not dispose of lithium batteri es in the trash.
• If the elect rolyte in the cells shoul d get on your skin, thoroughl y wash with soap
and water. If in the eyes, rinse thoroughly with cool water. Immediately seek
medical attention.
Recycle Rechargeable Batteries
Recycle used rechargeable batter ies at one of the many collection
sites in the U.S. and Canada. To nd the site nearest you, visit www.
call2recycle.org or call 1-800-822-8837.
4
Screw
1
2
6001434_UG_EN.indd 47/6/2016 3:25:42 PM
Install Batteries in the Remote Control
1. Make sure the remote control is turned o.
2. Use a screwdriver to open
the battery compartment.
Then insert four AA batteries
(not included), matching the
polarities (+ and –) marked
inside. Use alkaline batteries
for optimal performance.
Replace the cover.
Note: If the remote control’s LED
ashes during use, the batteries
are low and should be replaced.
Battery Notes
• Dispose of old batteries promptly and properly. Do not burn or bury them.
Use only fresh batteries of the required size and recommended type.
• Do not mix old and new batteries, dierent types of batteries (standard,
alkaline, or rechargeable), or rechargeable batteries of dierent capacities.
• Remove batteries during longer storage periods. Batteries can leak
chemicals that can damage electronic parts.
Pairing
1. Turn on the drone. The LEDs on the drone ash.
2. Place the drone on level ground.
3. Turn on the remote control. The remote control's LED ashes.
4. Move the throttle all the way up and then down to pair the remote control
with the drone. The drone’s propellers remain still during pairing. When
paired, all LEDs on both the remote control and drone light steadily.
Note: If pairing fails, turn o the drone and remote control and repeat the steps
above, or change locations to avoid electrical interference.
Fly Your Drone
There are 3 ways to take o:
For beginners: With the drone on the ground, press the button
drone will automatically take o, ascending about 5 ft (150cm) and then hover.
Intermediate users: With the drone on the ground, move the throttle forward
to ascend. To avoid ground air turbulence, y the drone at least 1 ft. (30cm) o
the ground.
Advanced users: Hold the remote control with one hand, resting your thumb
on the throttle. Throw the drone about 9 ft. (3m) away from you, and move the
throttle forward to y. The drone adjusts itself automatically and ies smoothly.
6001434_UG_EN.indd 57/6/2016 3:25:43 PM
. The
5
Loading...
+ 9 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.