Zeeva TL 0021 User Manual

Product Overview Remote Control

VIDEO

ON VIDEO

Package Contents

Drone Battery Charging

Drone Accessories Assembly

14+

EXPLORER

Drone

Instruction Manual

Thank you for purchasing the explorer drone.

This manual provides more information about this drone,

please read the instructions before using.

Start off

Power (Failure) program

The drone equipped four receivers for fault protection. When the drone is not received the remote control
signal, battery power failures or other failures, to ensure the motor does not start to achieve protection.

Step 1:

Turn on the power switch of drone, and place the drone on a flat
location, the status indicator start flashes, the gyroscope start
reading the midpoint.

Step 2:

Turn on the remote control power switch, push the Up/Down
joystick from the lowest to the highest, and then pull it down to
lowest position. Drone are ready for takeoff.

Operation Method

Note: To avoid losing control, always pay attention when controlling the drone.

Up/Down joystick

Turn Left/Right joystick Control drone left or right rotation

Control drone up and down

Left rotation

Lowest Highest

Right rotation

Front

Back

BackFront

Forward

Backward

Forward/Backward joystick

Left/Right side joystick

Control drone forward and backward movement

Left traverse Right traverse

Control drone left or right lateral movement

Sensitivity Settings

The drone have three operation modes: low, intermediate and advanced.

Tap the Forward/Backward & Left/Right side joystick enter setup mode
Turn on the remote control to enter the low axis mode (sensitivity up to 40%)
When the remote control to issue “DI” sound twice, axis into the intermediate mode (sensitivity up to 60%)
When the remote control to issue “DI” sound three times, axis into the advanced mode (sensitivity up to 100%)
The sensitivity can be adjusted by the fine-tuning button on the remote control, then press and hold the button
for one second to confirm or exit.

3D rolling action

When all the of the basic movements are skilled, you can try to
perform some advanced action. Click on the rolling action button of
the remote control, the remote emits a continuous sound, the
drone will trun into the 3D rolling action mode.

Explorer Drone x 1

Remote Control x 1

Propeller Guard x 4Landing Gear x 4

USB Charger x 1

Camera x 1

User Manual x 1

Specification

Remote control power supply: 3 x “AA” 1.5V Alkaline Batteries (Not Included)
Drone power supply: Rechargeable Li-ion Battery 3.7V
Charging time:1-2 hours
Play time: 6-7 minutes
Radio control type: RC model
Control distance: 70 Meters

Follow this Instruction can perform some 360-degree rolling action. In order to perform rolling action,
ensure to maintain the height of drone.

Left side tumbling

Push the "Forward/Backward & Left/Right side joystick" toward the right, then quickly turn joystick to the
left, finally push the joystick back to the middle.

Right side tumbling

Push the "Forward/Backward & Left/Right side joystick" toward the left, then quickly turn joystick to the
right, finally push the joystick back to the middle.

Front rolling

Pull the "Forward/Backward & Left/Right side joystick" backward, then quickly lift the joystick toward to the
top, finally push the joystick back to the middle.

Backflip

Push the "Forward/Backward & Left/Right side joystick" front, then quickly lift the joystick backward, finally
push the joystick back to the middle.

Under this advanced flight mode the drone is very fast and can perform a variety of tumbling instruction. You can
not perform rolling action when battery is low. Tap the "throttle joystick" back to normal mode.

High/Low speed switch

Up/Down & Turn
Left/Right joystick

Headless mode

One key return mode

Turn left
fine-tuning

Light Control

Power ON/OFF

Turn right
fine-tuning

Antenna

Indicator

Left side parallel

movement fine-tuning

Rolling action button

Forward/Backward &
Left/Right side joystick

Forward fine-tuning

Photo button

Video button

Right side parallel
movement fine-tuning

Backward fine-tuning

Remote Control Batteries Installation

3 x “AA” 1.5V Alkaline Batteries

(not included)

To install batteries into the controller,
unscrew the screw on the battery
box cover, to open the cover.
Insert 3 x “AA” batteries 1.5V Alkaline
Batteries (not included) into the battery box.
Batteries sould be placed as show on the diagram.

Notice:

When inserting the batteries, you must
insert according to the correct polarity,
the remote wont function if batteries are
reversed.

Notice

Please read this instruction manual carefully before operating the product.

Please do not operate the product in the gale.

The flying ground should be the local field and legal for remote control flying. Please do not operate the
product in forbidden zone or around people or animals.

Keep the aircraft a certain distance (at least 2-3 meters) from others when playing together.

Warning

This product is suitable to be used by people who has operating experience in flying model or aged no
less than 14 years old.

This product is not a toy but a precise equipment that integrating mechanics and electronics with expertise
of aerodynamics and high-frequency transmitting. It requires to be correctly assembled and debugged so
as to prevent the accident from being happened. The user should operate or control it in a safe way.

Please do not put the product in the mouth to prevent choking hazard of small parts.

Please do not put the finger into available interspaces.

Please do not play the product in a brutal way such as throwing, crashing or twisting it.

Please store the smaller-sized product accessories in places that are out of reach of children, in order to
avoid the occurrence of accidents.

The product is very powerful. For first time flight, it shall be observed that the joystick must be slowly
pushed in order to prevent the product from ascending too quickly and result in unnecessary collision and
damages.

When the flight is ended, the power supply of the remote control shall be switched off and then followed by
switching off the power supply of the product.

Avoid placing the batteries in places with high temperatures and exposure to heat.

When young children are operating the product, it shall be ensured that the adults are guiding and making
sure the product control is within the viewing range of the controller ( or instructor)such that it makes the
control very convenient.

When the product is not in use, please switch off the power supplies of both the aircraft and the remote
control, and remove the batteries in the remote control.

Please note that we won’t take any responsibility for any wrong operation as this may result in severe
injury or loss of property, and we cannot control the operating process during the time when the user
assemble or use this product.

Once this product is sold, we won’t be responsible for any safety responsibility during the time the user
operates or uses or controls this products.

ON VIDEO

OFF

ON

ON VIDEO

OFF

OFF

OFF

To recharge the battery of the drone, open battery box cover. Disconnect the rechargeable li-ion battery from the
drone. Connect and plug into the socket of USB charger for battery charging.

In the process of the battery charging, the indicator shows red light; after full charging, the indicator

diagram.

light will turn off.

Sould be placed as show on the

Drone Accessories Assembly

Propeller Guard: Insert four propeller guard into the holes of the propeller guard, and use the screwdriver

to lock four screws lightly.

Landing Gear:

Camera:

video section.

Insert the four landing gear into the landing gear holes at the bottom of the drone.

Insert camera stuck on fuselage buckle at the bottom of the drone. And plug the wire to the

Care and Maintenance

Always use dry and soft cloth to clean this product.

Avoid this product to be exposed to sunlight or heat.

Avoid immersing these toys into water, otherwise, the electronic parts may be damaged.

Regularly check and inspect the plug and other accessories. If any damages are discovered, please
immediately stop using it, until it is completely repaired in good working condition.

IMPORTANT: BATTERY INFORMATION

CAUTION:

1. TO AVOID BATTERY LEAKAGE

a. Always follow the instructions carefully. Use only batteries specified and be sure to insert
them
correctly by matching the + and - polarity markings.
b. Do not mix old batteries and new batteries or standard (carbon-zinc) with alkaline
batteries.
c. Remove exhausted or dead batteries from the product.
d. Remove batteries if product is not to be played with for a long time.
e. Do not short-circuit the supply terminals.
f. RECHARGEABLE BATTERIES: Do not mix these with any other types of batteries.
Always remove from the product before recharging.
Recharge batteries under adult supervision. DO NOT RECHARGE OTHER TYPES OF
BATTERIES.

2. Should this product cause, or be affected by, local electricl interference, move it away
from
other electrical equipment.Reset ( switiching off and back on again or removing and
re-inserting batteries) if necessary.

Propeller Guard:

Landing Gear: Camera:

VIDEO

ON

OFF

Camera Photo / Video Instructions

Turn the drone power on, the camera ready when the RED indicator change from flasching to BLUE and
keep light on. If the RED indicator light on and light off for after few seconds, it means the SD card is not
in the camera. Please insert the SD card, than the indicator light will turn off.

Photo: Press the photo button from remote control, will issue a “DI” sound. The indicator light of camera
will flash one time, and take a photo.

Video: Press the video button from remote control and hold for several seconds, will issue continue “DI
DI DI” sound. The indicator light of the camera will be flashing, it will start recording video, press
the button again, the RED light turn BLUE, and the camera will stop recording.

FCC Statement

This device complies with the part 15 of the FCC rules. Operation is subject to the following
two conditions:(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Caution: changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with instructions may cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on. The user is
encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.

• Consult the dealer or experienced radio/ TV technician for help.

FCC ID: 2ADM5-TL-0021

Keep All Relevant Information for Future Reference