P310i
Table of contents
Loading...
Card
General information
Printer
Solutions
FOREWORD
This manual contains installation and operation information for the P310
i
Series card printers manufactured by Zebra Technologies Corporation,
Camarillo, California.
RETURN MATERIALS AUTHORIZATION
Before returning any equipment to Zebra Technologies Corporation for
in-warranty or out-of-warranty repair, contact Repair Administration for a
Return Materials Authorization (RMA) number. Repack the equipment in the
original packing material and mark the RMA number clearly on the outside.
Ship the equipment, freight prepaid, to the address listed below:
For USA, and Latin America
Zebra Technologies Corporation
Card Imaging Division
1001 Flynn Road
Camarillo, CA. 93012-8706. USA
Phone: +1 (805) 579 1800
Fax: +1 (805) 579 1808
Toll Free in US: (800) 452-4056
For Europe, Asia and Pacific:
Zebra Technologies Corporation
Card Imaging Division
Zone Industrielle, Rue d’Amsterdam
44370 Varades, France
phone: +33 (0) 240 097 070
Fax: +33 (0) 240 834 745
COPYRIGHT NOTICE
This document contains information proprietary to Zebra Technologies
Corporation. This document and the information contained within is
copyrighted by Zebra Technologies Corporation and may not be duplicated
in full or in part by any person without written approval from Zebra. While
every effort has been been made to keep the information contained within
current and accurate as of the date of publication, no guarante is given or
implied that the document is error-free or that it is accurate with regard to
any specification. Zebra reserves the right to make changes, for the purpose
of product improvement, at any time.
TRADEMARKS
P310iis a service mark and Zebra is a registered trademark of Zebra
Technologies Corporation. Windows and MS-DOS are registered
trademarks of Microsoft Corp. All other marks are trademarks or registered
trademarks of their respective holders.
I
Card
General information
Getting started
Operation
Cleaning
Specifications
Appendix A
Appendix B
Troubleshooting
Printing a card
Appendix C
P310iPlastic Card printer
Printer
Solutions
PRODUCT WARRANTY STATEMENT
Printers
All Zebra Card Printers are warranted against defects in material or
workmanship for twelve (12) months from the purchase date.
Proof of purchase or shipment date is required to validate the warranty
period. The warranty becomes void if the equipment is modified,
improperly installed or used, damaged by accident or neglect, or if any
parts are improperly installed or replaced by the user.
Note: Products returned must be packaged in the original or
comparable packing and shipping container. In the event equipment is
not so packaged, or if shipping damage is evident, it will not be
accepted for service under warranty. Surface transportation charges
for return to customers in the continental United States is paid by
Zebra. Otherwise, Zebra pays CPT (carriage paid to) nearest airport,
customer pays customers, duties, taxes, and freight from airport to
destination. If Zebra determines that the product returned for warranty
service or replacement is not defective as herein defined, the customer
will pay all handling and transportation costs.
Printheads
Since printhead wear is part of normal operation, the original printhead
is covered by a twelve (12) month warranty. Warranty period begins on
purchase date.
To qualify for this warranty, the printhead must be returned to the
factory or to an authorized service center. Customers are not required
to purchase Zebra supplies (media and/or ribbons) for warranty
qualification. However, if it is determined that the use of other
manufacturer supplies has caused any defect in the printhead for which
a warranty claim is made, the user is responsible for Zebra’s labor and
material charges required to repair the defect. The warranty becomes
void if the printhead is physically worn or damaged; also if it is
determined that failure to follow the preventive maintenance schedule
listed in the User’s Guide has causes defect in the thermal printhead for
which a warranty claim is made.
Spare Parts
All parts, maintenance kits, options kits, and accessories are warranted
to be free of defects in material and workmanship for 90 days (except
where otherwise denoted) from date of purchase. This warranty
become void if the item is modified, improperly installed or used, or
damaged by accident or neglect.
II
Card
General information
Getting started
Operation
Cleaning
Specifications
Appendix A
Appendix B
Troubleshooting
Printing a card
Appendix C
P310iPlastic Card printer
Printer
Solutions
DECLARATIONS OF CONFORMITY
This equipment is being tested for compliance with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses ans can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference’s by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
The user may find the following booklet, prepared by the Federal
Communications Commission, helpful:
How to identify and resolve Radio/TV Interference Problems. This booklet is
available from the U.S. Government printing Office, Washington, D.C.
20402, Stock No. 004-000-00345-4.
Use of a shielded cable is required to comply within Class B limits of Part 15
of FCC Rules.
Pursuant to Part 15.21 of the FCC Rules, any changes or modifications to
this equipment not expressly approved by Zebra may cause, harmful
interference and void the FCC authorization to operate this equipment.
INDUSTRY CANADA NOTICE
This device complies with Industry Canada ICS-003 class A requirements.
III
Card
General information
Getting started
Operation
Cleaning
Specifications
Appendix A
Appendix B
Troubleshooting
Printing a card
Appendix C
P310iPlastic Card printer
European Council Directive
73/23/EEC modified
by 93/68/EEC
EMC Directive
EN 500082-1,1992
Immunity to
Electromagnetic
Disturbances
Compliance to Standards
89/336/EEC
modified by
92/31/EEC and
93/68/EEC
RF Emissions
control
Low voltage
Directive
EMC Directive
EN 60950
EN 55022-B
Product safety
Model: P310iconforms to the following specification:
FCC Part 15, Subpart A, Section 15.107(a) and Section
15.109(a) Class B digital device-Testing in process
Printer
Solutions
INTRODUCTION
Thank you for choosing the Zebra P310iPlastic Card Printer.
These printers produce cards ideal for personalized identification, access
control, visitor, membership, promotion and luggage card, badges and
tags.
This manual guides you to an efficient start up and operation of your new
Card Printer.
P310iPRINTER MODELS
Zebra's Product Numbers tell the story:
Here is a quick review of Zebra's Card Printer Series numbering and
lettering system to help you.
Zebra's P310i Plastic Card Printer Series employ Dye Sublimination and
Resin Thermal Transfer Technologies. Model numbers include identifiers
that specify options and items in the Ship-Away kits.
Printer Type:
I = RFID
C = Color
F = Monochrome
Smart Card:
O = No
E = Yes
Magnetic Encoder:
O = No
M = Yes
Magnetic Encoder Options:
O = No
1 = Stripe down HICO
2 = Stripe Down LOCO
3 = Stripe Up HICO
4 = Stripe Up LOCO
Memory:
O = Standard
Interface:
P = Parallel (DB - 25 Male)
S = Serial (DB - 25 Female)
U = USB/Parallel
R = USB/Serial
IV
Card
General information
Getting started
Operation
Cleaning
Specifications
Appendix A
Appendix B
Troubleshooting
Printing a card
Appendix C
P310iPlastic Card printer
}
Ship-away kit
P310i X - X X X X X - X DO
DO =Documentation CD &
Driver Wizard
Power Cord:
I = International (120 / 220)
U = UK
Printer
Solutions
Card
General information
Getting started
Operation
Cleaning
Specifications
Appendix A
Appendix B
Troubleshooting
Printing a card
Appendix C
P310iPlastic Card printer
V
Important general information
Mechanical hazard, such as one associated
with moving parts, capable of resulting in
equipment damage or personal injury.
Electrical hazard, such as an exposed voltage
point, capable of causing electrical shock and
personal injury.
An area where electrostatic discharge (ESD)
can cause component damage. Use a
grounding wrist band.
Elevated temperature hazard, capable of
producing a burn.
Keep Card Printer clean by minimizing cover
open time.
ICONS
Throughout this manual, different icons
highlight important information, as follows:
Printer
Solutions
Table of contents
ICONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
UNPACKING YOUR CARD PRINTER . . . . . . . . . . . . . . . . . . . 1
INDICATORS AND CONTROLS . . . . . . . . . . . . . . . . . . . . . . . 3
ITEMS INCLUDED WITH YOUR PRINTER . . . . . . . . . . . . . . . 3
PRINTER INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
P310i PRINTER FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . 5
LOADING RIBBONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
LOADING CARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
FEEDING ONE CARD AT TIME . . . . . . . . . . . . . . . . . . . . . . . . 11
REMOVING CARD CARTRIDGE . . . . . . . . . . . . . . . . . . . . . . . 11
PRINTING A TEST CARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
PRINTING A SAMPLE CARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
CLEANING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
CLEANING THE PRINT HEAD . . . . . . . . . . . . . . . . . . . . . . . . 19
CARD CLEANING CARTRIDGE . . . . . . . . . . . . . . . . . . . . . . . 20
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
TECHNICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
APPENDIX A - MAGNETIC CARD STRIP ENCODER . . . . . . . . . . . . 29
APPENDIX B - SMART CARD CONTACT STATION . . . . . . . . . . . . 31
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
APPENDIX C - ACCESSORIES AND SUPPLIES . . . . . . . . . . . . . . . . 33
RIBBONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
CARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
VI
Card
General information
Getting started
Operation
Cleaning
Specifications
Appendix A
Appendix B
Troubleshooting
Printing a card
Appendix C
P310iPlastic Card printer
Printer
Solutions
Card
General information
Getting started
Operation
Cleaning
Specifications
Appendix A
Appendix B
Troubleshooting
Printing a card
Appendix C
P310iPlastic Card printer
1
Your P310iprinter ships in a carton and
protective anti-static bag. Keep all packing
material in case you need to move or re-ship the
printer.
While unpacking, inspect the carton to ensure
that no damage occurred during shipping.
Please ensure that you have a clean and nearly
dust free environment for proper operation and
storage of the printer.
UNPACKING
YOUR CARD
PRINTER
GETTING STARTED
Printer
Solutions
In addition to user documentation, make sure the
following items are included with your P310
i
printer:
2
Card
General information
Getting started
Operation
Cleaning
Specifications
Appendix A
Appendix B
Troubleshooting
Printing a card
Appendix C
P310iPlastic Card printer
If any items are missing, please contact your dealer.
To reorder, please refer to Appendix C of this manual.
+ OPERATOR HELP GUIDE
(Not Shown)
CARD CARTRIDGE
POWER CABLE
CARD OUTPUT HOPPER
INTERFACE CABLE
CD Rom with driver Wizard &
user’s manual
CLEANING KIT
CARD CLEANING
CARTRIDGE
Printer
Solutions
INDICATORS (green, amber & red) signal printer
activity by illuminating or flashing, a follows:
3
Card
General information
Getting started
Operation
Cleaning
Specifications
Appendix A
Appendix B
Troubleshooting
Printing a card
Appendix C
P310iPlastic Card printer
Your P310i printer has three Status indicators and
a panel button on the front and power switch on
the rear :
INDICATORS
AND CONTROLS
Printer
Solutions
Card
General information
Getting started
Operation
Cleaning
Specifications
Appendix A
Appendix B
Troubleshooting
Printing a card
Appendix C
4
PRINTER
INSTALLATION
The following will guide you through the
installation of your P310i Printer.
CAUTION: Limit AC power supplied to the P310i
to 110 ~ 230 volts, 60 ~ 50 Hertz, for an
associated 800 ~ 400 milliamps. Limit excess
current draw to 16 amps or less, using an
associated circuit breaker or other such device.
Never operate the printer in a location where
operator, computer, or printer can get wet.
Personal injury could result. The electrical
security of the printer is based on the reliability
of the mains power source.
1. Place the printer in a location that allows easy
access to all sides. The printer should never be
operated while resting on its side or upside
down.
2. Place the printer's power swith in the OFF (0)
position.
3. Insert the power cable into the printer power
socket and attach to grounded electrical socket
of the proper voltage and type.
4. Attach interface cable to printer and computer
and then secure.
5. Switch power on.
CAUTION: Intermittent or unpredictable
operation may occur from unsecured
connectors. If damaged, the power cable must
be replaced by an exact equivalent.
P310iPlastic Card printer
Printer
Solutions
Card
General information
Getting started
Operation
Cleaning
Specifications
Appendix A
Appendix B
Troubleshooting
Printing a card
Appendix C
5
OPERATION
P 310i PRINTER
FEATURES
The following shows the features found on your
P310i Printer.
STANDARD FEATURES OPTIONAL FEATURES
1. Print Head A. Magnetic Encoding Station
2. Print Head Unlock Lever B. Smart Card Contact Station
3. Manual Holder
4. Card Output Hopper
5. Status Indicators
6. Panel Button
7. Card Cleaning Cartridge
8. Card Cartridge
9. Card Thickness Control
PLEASE NOTE: Any blue items inside the printer can be operated by the user.
P310iPlastic Card printer
Printer
Solutions
Card
General information
Getting started
Operation
Cleaning
Specifications
Appendix A
Appendix B
Troubleshooting
Printing a card
Appendix C
6
LOADING
RIBBONS
“i Series”Printers requires the use of “i Series”
ribbons for full color printing. The Resin
Thermal Transfer and Dye Sublimation ribbons
for P310i only are specifically designed for your
P310i Printer. For optimum performance and
printer life (Print Head), use True Colors ribbons.
DO NOT TOUCH the print head or the electronic
components on the print head carriage.
Discharges of electrostatic energy that
accumulates on the surface of the human body
or other surfaces can damage the print head and
other electronic components used in the device.
1. Remove ribbon from packaging.
2. Open cover and press down on the print
head unlock lever to open the print head
carriage. The print head carriage will pop
open.
Continued on next page .......
P310iPlastic Card printer
Printer
Solutions
Loading...